Search Documents

By Ruddle R. W.

Magnetite occurs in the reverberatory furnaces, blast furnace and converter (a) as the result of its presence in the materials charged, and (b) as the result of oxidation of the FeS in the charge in the absence of sufficient SiO2 to slag the FeO as it is produced and thus prevent its subsequent further oxidation. Magnetite is reduced by FeS according to FeS+3Fe3O4=10FeO+SO2 and similar reactions. This reaction is markedly affected by temperature and does not proceed to any important extent below about 1200°C. To ensure comparative freedom from magnetite it is therefore necessary to raise the temperature of the furnace to the highest practicable figure and to use plenty of siliceous flux. Since the maximum operating temperature is likely to be limited by the resistance of the refractories to attack by the slag, investigation of the factors affecting this attack should be helpful. It is reasonable to suppose that the formation of magnetite might be minimized by ensuring intimate admixture of matte and slag during conversion so that silica is readily available for combination with ferrous oxide as the latter is formed. The literature gives no clue to the importance of this factor and some experimental work on this aspect might be fruitful

Jan 1, 1953

Discussion of papers with authors' written replies and closing remarks.

Jan 1, 1947

By Winmill T. F.

(Paper presented at the Institution of Mining Engineers' general meeting held in London on 8th June 1916.) The conclusions reached in this paper may be summarized briefly as follows: (1) The method of estimating moisture in coal by determining the loss in weight of a sample heated to 105°-110° Cent, in an air-bath for an hour is untrustworthy, the results so obtained being too low. (2) Dried coal has a very considerable power of absorbing moisture, and a sample, after being dried, must be protected instantly if it is to remain free from moisture. (3) A fairly accurate estimation may be made by heating the coal in a current of dry air at 105° to 110° Cent., and collecting the moisture evolved. (4) In cases in which it is proposed to use the dried coal for any further experiments, the drying must be done in the absence of oxygen, and this can be done simply and quickly by the vacuum method now described

Dec 1, 1916

By A. Policard

The question, of the pathogenesis of pneumokoniosis is very important not only from the social and economic points of view but also from the purely biological. The study of the pathogenesis of the disease leads to fascinating problems of cytology and cytochemistry. Two problems present themselves for examination from an analytical and critical point of view: 1. The first reactions of the alveolar walls to inhaled dusts. 2. The precise nature of the action of mineral dusts.

Jan 1, 1947

By M. D. Gibbs, T. N. Smith, B. Verbaan

When heated in the absence of oxygen, pyrite from refractory gold concentrates decomposes endothermically to pyrrhotite, releasing sulphur. The decomposition starts at the particle surface and progresses inwards, leaving an adhering layer of porous pyrrhotite. Use of the conventional shrinking-core model implicitly assumes a negligible partial pressure of sulphur in the bed, but this pressure is in fact at least equal to the equilibrium vapour pressure of sulphur over pyrite, constituting the principal control of the rate of decomposition. Further experiments showed a decrease in reaction rate as the conversion increased. Both phenomena are attributed to the persistence of non-isothermal conditions in the fluidised bed during pyrolysis, caused by the endothermic nature of the reaction and the relatively slow rates of heat transfer to particles and vapour removal from the bed. Equipment must be developed to maximise these two parameters

Jun 19, 1905

By K. El-Barawi, Hussein M. Kamal

Chlorination was performed of iron-rich chromite ore from Barramyia, United Arab Republic (UAR), together with its concentrate. The effects of change of grain size, chlorine gas flow rate, time and temperature were studied. The extent and mechanism of chlorination were followed through chemical and structural analyses of the feeds and complete chemical analysis of the chlorination products. By conducting the chlorination process for short periods at 600°C or lower temperatures, products having high Cr-Fe ratios suitable for ferrochrome production can be obtained.

Dec 1, 1971

The mineralogical composition of the ore was determined and the mineral phases with which nickel is associated were identified. The ore was prepared by grinding to -420 micrometres and classification into granulometric fractions. Prior to the main series of experiments the effect of agitation rate on nickel recovery was investigated. The influence of sulphuric acid concentration, temperature and particle size on the kinetics of nickel extraction was then studied, both quantitatively and qualitatively, over fixed value intervals. Application of the initial rate method enabled determination both of the order of reaction with respect to sulphuric acid concentration and the activation energy for the dissolution of nickel. The results indicate that a physical mechanism can be ruled out as the rate-determining step in the extraction of nickel from the ore and that a chemical mechanism is more likely

Dec 1, 1991

By Hirsch H. H.

The paper, presented at the North of England Institute of Mining Engineers' general meeting held in Newcastle-upon-Tyne on 12th February 1916, gives a short description of the Hirsch lamp, which, though largely used in the United States of America, has not yet been adopted in Great Britain. The lamps, which consist of (1) the watchman's lamp and (2) the miner's lamp, are portable, and have been designed to provide a safe and reliable light for use by watchmen, and in mines, rescue-work, powder-works, oil-refineries, and other places where special precautions become necessary on account of the presence of explosive materials or gases. The lamps are in each in­stance operated by a storage-battery contained within a casing, and this supplies the current necessary for a miniature incandescent lamp. Each safety-lamp forms a complete unit and can be carried from place to place or held in any position. Appendices give details of battery cleaning, test results and safety reports

Dec 1, 1916

By M. L. Schmulian

"The Windarra nickel deposits display many of the characteristics that typify Archaean volcanic peridotite-associated nickel sulphide ores of Western Australia. The Fe-Ni-Cu sulphide mineralization, which comprises dominantly disseminated sulphides, occurs at the base of a differentiated ultramafic volcanic pile grading upwards from massive meta-peridotitic flows to thin, locally spinifex-textured meta-picritic units. The entire mafic-ultramafic belt has been subjected to mid-amphibolite- facies metamorphism. The ore-bearing ultramafic is immediately underlain by dominantly sulphide-facies banded iron formation (BIF), which commonly contains nickel sulphides adjacent to its contact with mineralized ultramafic. BIF-hosted ores are formed both by physical remobilization of ultramafic-hosted sulphides and by migration of Ni and Cu into pre-existing iron sulphides.At Mt. Windarra the mineralization comprises eight steeply dipping, steeply plunging elongate oreshoots, which display a marked parallelism with major and minor fold structures in the underlying BIF. Seven of the shoots occur at or close to the base of the ultramafic pile, and are hosted by at least three overlapping flows. The zone of overlap occurs at the northern end of each flow, where picritic ultramafic, representing a dominantly liquid portion of the flow, occupies the basal contact. A gross south- north ultramafic flow direction is inferred. The eighth shoot occurs in a stratigraphically higher position within the ultramafic sequence.At South Windarra at least two overlapping mineralized flows occupy the basal contact, the ore zone having a strike extent three to four times its downdip extent. There is no obvious structural control to the mineralization."

Jan 1, 1984

By D. F. Ball, P. R. Dawson, J. T. Fitton

Report of discussion at December, 1970, IMM general meeting (Chairman: M. J. Cahalan, President) and contributed remarks on the paper published in Transactions/Section C (Mineral Processing & Extractive Metallurgy), vol. 79, September, 1970, pp. C189-96, plus the authors' replies. Contributors included Cohen E., Hope B., Wasse D.G., Shakespeare A.G., Burwood D.S., Jones H.A., Dartnell J., Carter G.C., Henderson T.A., Relf G. and Clark S.W.

Dec 1, 1971

Jan 1, 1947

By B. H. Smith

"Most of the discoveries of nickel sulphide deposits in Western Australia have followed the search for gossans. The chances of further discoveries depend on improving our understanding of the cover of strongly leached and transported materials that obscure approximately 85% of the area of the Yilgarn Block that has nickel sulphide mineralization potential. The lateritic profiles that are observed on the Yilgarn Block today were formed over a period of more than 100 m.y. of warm and humid climates. This lateritized land surface has been preserved by induration during subsequent arid climates as well as by the structural stability of the Yilgarn Block.In geochemical surveys of lateritied terrain samples have to be taken from at least the saprolite zone usually by drilling so that confident predictions can be made of the significance of analytical data. Account must be taken of the mineralogy of samples, as well as the nature of the horizon of a laterite profile that is being sampled, owing to the concentrating effects on trace elements of Fe and Mn oxides.Multivariate techniques have been applied successfully to analytical data in gossan recognition when textural evidence is ambiguous. Pathfinder geochemistry has also been used in gossan recognition and the most significant recent advance has come from studies of platinum group metals in nickel sulphides and their dispersion during weathering."

Jan 1, 1984

By J. A. Saunders, E. L. Rowan

It is now widely accepted that the metal-rich waters found in the oil wells are possible present-day analogues of the mineralising solutions that formed the Mississippi Valley-type (MVT) deposits throughout mid-continental USA and elsewhere. A study characterising the trace-metal content provides additional circumstantial evidence for a genetic link between sediment-hosted mineral deposits and basin brines: Ag, Co, Ni, As and Mo, detected in the scale, are locally present in accessory minerals in MVT deposits and the levels of Ag found in the wells support the conclusion that sedimentary sources for silver should be considered in evaluating the origin of Pb-Zn-Ag deposits in sedimentary terrains

Jun 12, 1905

By Gibson J.

Written discussion contributions to the paper presented at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 12th February 1916, with Mr. T.Y. Greener, President, in the chair, comprise comments by Kilpatrick W.M., Routledge W.H., Watson J. and Smith W., along with the author's reply. Also briefly noted are the demonstration of two pieces of equipment, an incline chock and a cage arrestor

Dec 1, 1916

By Winmill T. F.

Paper presented at the at the Institution of Mining Engineers' general meeting held in London on 8th June 1916: In a previous paper it has been shown that the rate of absorption of oxygen by coal is neither directly proportional to the surface area of the coal exposed nor to the percentage of oxygen in the air. Further experiments are now described supporting this conclusion

Dec 1, 1916

By M. D. Pritzker

Shrinking-core models are used to describe the physico-chemical processes that are associated with many metallurgical gas-solid and liquid-solid reactions. The models can be used to evaluate rate constants and effective diffusion coefficients from experimental data. This work generalises the model for diffusion through a product layer to cases where the transport of more than one species is rate-controlling

Jul 1, 1991

By G Fakes

This paper describes the history of civil engineering tunnelling and developments in soft ground techniques during the 19th and 20th centuries, culminating in the design and use of high speed tunnelling machines for all types of ground conditions. Some of the problems encountered are outlined, and descriptions are given of some contemporary developments in rock tunnelling techniques, with comparisons of methods used in the mining industry.

Jan 5, 1996

"Prior to the publication of the General Report of the Miners' Phthisis Prevention Committee of South Africa in 1916 little attention was paid to the dust hazard and the necessity for its suppression in the underground workings of the Broken Hill mines. Such precautions as were observed for the elimination of dust were related rather to the prevention of lead poisoning, which, in the early days of Broken Hill when large tonnages of lead carbonate ore were being won, was rather prevalent. Ventilation and hygiene followed the general practice in this and most foreign countries.This paper covers incidence and action since 1918, considering medical aspects and operating aspects. "

Jan 1, 1947

Jan 1, 1947

By G. D. Nicholls

There have been very few attempts to isolate the various factors that contribute to the overall imprecision of geochemical analytical procedures, due in part to the difficulty of distinguishing between them. The technique of spark source mass spectrography permits a ready distinction between the contributions to overall precision from sampling error and instrumental and other errors. With conventional methods of sample preparation for this technique sampling difficulties are responsible for 80-90 per cent of the overall imprecision. Examination of the probable location of the major difficulties in sample preparation indicates that the preliminary stage of grinding, mixing and extraction of a first aliquot (about 1/100 of the original sample) is generally perfectly adequate. The difficulty lies in the subsequent stages of sample preparation. Dry mixing techniques are unlikely to give good precision if the sub-samples actually examined by the analytical technique are less than 10 mg in amount. Solution techniques are less prone to sampling difficulty. Fusion techniques, unless conducted with great care, can produce more difficulty than dry mixing. Sample preparation is critical to the success of many analytical procedures. Selection of appropriate sample preparation techniques requires just as much care as the selection of techniques for the actual analysis.

Dec 1, 1971