Search Documents

By K. A. Natarajan

Interaction with microorganisms results in significant surface chemical changes on minerals. For example, chemolithotrophs such as Thiobacillus ferrooxidans and Thiobacillus thiooxidans significantly alter the surface chemistry of several sulfide minerals such as pyrite, chalcopyrite, sphalerite and galena. Heterotrophic bacteria such as Bacillus sp. could alter the electrokinetic properties of oxide minerals such as hematite, alumina, silica, kaolinite and calcite. Microbe-mineral interactions could thus be beneficially utilised in mineral beneficiation as different from bioleaching. Microbially induced mineral beneficiation unlike bioleaching deals with interfacial phenomena at mineral-solution-bacteria interfaces and surface chemical changes are brought about at very rapid rates amounting to a few minutes resulting in mineral separations in an aqueous medium.

Jan 1, 2003

By Pradip, Beena Rai

A molecular modeling study was carried out on an adsorbed oleate monolayer on the surfaces of three calcium minerals, fluorite, calcite and fluorapatite using Universal Force Field (UFF) potentials. The cleavage plane of calcite {104} was the best template for oleate monolayer adsorbed since the surface structure enabled all the calcium sites available on the surface to be occupied by oleate anions. The area occupied per chain of oleate in this well packed monolayer was computed to be 20.2 Å, which exactly matches the value calculated to be the parking area per oleate molecule for a fully packed monolayer based on strictly geometric calculations. On the other hand, the precentage of calcium sites occupied by oleate to achieve a fully packed monolayer in case of fluroite and and fluorapatite was found to be 67% and 75% respectively. The results of this theoretical study suggest that while all the three adsorption conformations, that is unidentate, bidentate and bridging type are equally likely on fluorite and fluorapatite, bridging is most likely on calcite. Interestingly, all the conformations are observed experimentally for calcite-oleate system also. The reasons for this discrepancy between the theoretical predictions and experimental observations are not clear. More work is required to resolve this discrepancy, in particular simulation studies in presence of solvent water molecules on the surface.

Jan 1, 2003

By Kang N. Zhong, Hui H. Luo, Yunan Phosphate Chemical Co., Yi H. Wei, Yao J. Li, Yu L. Wang

"The three kinds of phosphate ores (igneous, metasedimentary and sedimentary) found in China have great differences in flotation flowsheets and reagents suite because of their crystal structure and mineral composition. The igneous and metasedimentary apatites have good floatability with fatty acid as collector and waterglass, sodium hydroxide or sodium carbonate as conditioners. The sedimentary phosphate is very difficult to beneficiate by direct flotation because of their poor floatabilities and relatively high content of MgO and SiO2, even though the dolomite depressants are used sometimes.The differences in floatability of apatites in China are closely related to their differences in specific surface area. The amount of collector to float apatite increases with the specific surface area. Apatite with lower specific surface area showed good floatability at lower collector concentration. Apatite with a higher specific surface area needed a higher concentration of collector. The content of CO3 2- will affect the specific surface area of apatite by distortion of its crystal structure and consequently affect its floatability.Dolomite can be easily rejected from apatite in a weak acidic medium (pH=5), especially in phosphoric acid medium by reverse flotation. Quartz and siliceous gangue in sedimentary apatite can be removed by direct flotation using fatty acid or by reverse flotation using amine. Amine is not practically applied because sedimentary apatite in China is usually very fine and needs fine grinding, which always results in excessive, very fine, stable and non-flowable foam.Based on the floatability of phosphate ore in China, a two-stage flotation process, direct and reverse flotation (D+R), was developed to beneficiate sedimentary ore. For the Haikou phosphate ore containing 25.11% P2O5, 3.46% MgO and 16.5% SiO2, a concentrate containing 31.84% P2O5, 0.48% MgO and 14.8% SiO2 can be obtained through a continuous D+R test at a recovery of 89%."

Jan 1, 2003

By Elzbieta Mielczarski, Jerzy A. Mielczarski

"It is well documented that xanthate adsorption on sulphide minerals is electrochemically controlled process. Under well controlled potential conditions the adsorption of xanthate takes place at different potential on each mineral, hence, each mineral component can be selectively separated from ore. This was demonstrated in the past for single mineral systems. In real flotation this concept never works out for two reasons: the potential of single mineral particle results from its interaction with solution as well as from galvanic contact with other particles present in the flotation pulp. Thus, the potential of a single particle results from complex surface reactions controlled by solution chemistry and the presence of other mineral particles that also interact with the solution. In flotation it is not possible to control mineral particle potential as it was demonstrated in voltametric studies of single mineral.In this study adsorption of xanthate on pyrite, galena and chalcopyrite has been investigated in the presence of those minerals. The second mineral was in solution: (i) without any physical contact with the first one, (ii) in direct contact (non-liberated grain or connected by wire), (iii) in collision type contact similar to that observed in real flotation.The adsorption of amyl xanthate on pyrite, galena and chalcopyrite was monitored by infrared external reflection technique directly on mineral surfaces. Type of the adsorbed species and their amount were concluded from the recorded reflection spectra. The presence of second mineral in solution without any physical contact does not influence adsorption. The minerals behave as if they were separated (at least during 30 min of the experiment). However, any type of galvanic contact between grains of two different minerals has tremendous consequence on the adsorption of collector on the both minerals. The detected changes are dramatic, from no adsorption to a few monolayer coverage formation.For example, pyrite that adsorbs amyl xanthate strongly in single mineral system in its galvanic contact with galena practically shows no adsorption of the collector in the same solution conditions. On contrary adsorption of xanthate on galena is tremendously enhanced during the galvanic contact with pyrite. The observed changes in the surface reactions are discussed and mechanisms of xanthate interactions in different galvanic contact are proposed."

Jan 1, 2003

By Konstantin Fedotov, Victor Beloborodov, Anatoly Potyomkin

"There are areas in Russia, which cover huge territories and they are north, and Siberia. These difficult to access regions with cold climate are rich in a great number of distant deposits of valuable and rare metals, gold and platinum. The development of such deposits requires highly effective technologies of mineral processing which could be realized in modular and quick-built processing plants.The work presented includes the results of long term research in the development of new technologies of processing of zirconium (in the form of rare mineral Baddeleyite – natural zirconium dioxide) bearing ore of the Kovdor deposit which is located in the Polar region of the Kola peninsular and also in Siberia deposits of of ledge ores of gold."

Jan 1, 2003

By Chris A. Bennett, Glenn S. Dobby, David A. Bulled

Establishing reagent dosing strategies for new ore bodies has traditionally involved a combination of experience and empirical experimentation using standard laboratory tests. The grade and recovery data resulting from these lab tests have historically been used as direct indicators of plant performance despite the obvious differences between the flotation environments. A reagent scheme selected in this way would subsequently be employed to generate the grade and recovery information for the geometallurgical model which in turn was used for metal production and cash flow forecasts. If the reagent scheme was sub-optimal then so too would be the forecasts and the resulting cash flow.

Jan 1, 2003

By J. B. Rubinstein

"The paper gives an overview of the history of flotation machine development. The laws of their evolution are stated and the place and role of column flotation are demonstrated.The major parameters of column cell diameter and height are discussed. Options are proposed for optimization of the hydrodynamic characteristics of large-capacity column cells. The high efficiency of columns with cell height of 4-6 m is demonstrated. The optimum parameters of multisectional column machines are determined. Their advantages compared to monocells are shown. A scaling-up procedure for column machines was developed based on flotation macro- and microhydrodynamics simulation."

Jan 1, 2003

By Carin Laubscher, Francis W. Petersen, Jaap P. Smit

"Waste streams, such as acid mine drainage, are often characterised by low pH values and high concentrations of heavy metals, dissolved solids, calcium and sulphates. Although lime remediation effectively removes most of the heavy metals as hydroxides, it is less effective at lowering levels of sulphates. Various methods of removing sulphates from effluents exist, such as precipitation with lime, precipitation with barium salts, co-precipitation with calcium carbonate, reverse osmosis, and ion exchange. Mintek developed a chemical precipitation (SAVMIN) process to treat acid mine drainage, which entails the addition of lime to precipitate the metal hydroxides, and the subsequent formation (precipitation) of calcium sulphoaluminate or ettringite. The key to the viability of the new technology lies in the correct use, regeneration and recycling of Al(OH)3 used to precipitate the ettringite. The water produced by this process is suitable for disposal to watercourses or for agricultural, domestic or industrial consumption. No brines are produced as the salts are converted to solid hydroxides, gypsum and calcium carbonate.The SAVMIN process has been tested successfully during several laboratory scale operations, and during two pilot plant operations at Stilfontein Goldmine for Anglogold and Navigation Plant, Witbank for Anglocoal. During the pilot plant campaign at Navigation Plant, metal and mineral precipitation was achieved with lime addition. The sulphate concentration in the water was reduced from 2136 mg/L to an average value of 102 mg/L and the calcium concentration was reduced from 727 mg/L to an average value of 70mg/L.The SAVMIN process generates a number of different waste streams including metal hydroxide sludge from neutralisation, gypsum sludge from the gypsum crystallisation steps, and calcite sludge from carbonation. The metal hydroxide sludge is composed of Mg, Ca, Mn and Fe hydroxide, and could be disposed of on a slimes dam. Gypsum sludge was greater than 99% CaSO4.2H2O. This gypsum could be used for dump or road capping, underground backfilling, production of wallboard and cement. The calcite sludge is pure CaCO3, which is recycled back to the neutralisation stage."

Jan 1, 2003

By Peter N. Holtham, Mary M. Ng

"Resistivity measurements of minerals in the laboratory are commonly made with a low DC voltage source. Common test voltages specified in the ASTM Standard D257 are 100, 250, 500, 1000, 2500, 5000, 10000 and 15000 V, however 100 and 500 V are the most frequently used. Resistivity results obtained in the laboratory have been used to infer the electrical behaviour of minerals undergoing electrostatic separation. However because the voltages employed in electrostatic separation in the plant are of the order of thousands of volts, typically greater than 15000 V, whether the laboratory results are applicable as a predictor of plant performance is a critical question. It is unclear whether resistivity values taken at a low voltage are characteristic of those seen in electrostatic separation, in which the minerals are exposed to a much higher voltage. No definitive answer could be found in the literature.In this work, the resistivities of zircon, rutile and ilmenite were measured in a corona field for the first time. The measurement principle was based on a technique developed to measure fly ash resistivity in electrostatic precipitators, however the test apparatus and findings are novel.Resistivities of rutile and zircon were found to be easy to measure. The values measured in a corona field were several orders of magnitude less than those obtained with a dc voltage of 100 V. Evidence of back corona was observed with zircon. When the voltage drop was greater than the sample layer could withstand a localised electrical stress developed, resulting in a voltage breakdown, at which point a sudden surge of corona current (back corona) was detected in the sample layer. Rutile, on the other hand, exposed to the same conditions as that of zircon (i.e. same temperature and applied voltage) did not exhibit any sign of back corona. Its resistivity across the range of test voltages (14 to 33 kV) remained fairly constant."

Jan 1, 2003

By James Y. Oldshue

"Very seldom is it possible when contacting a gas with a slurry to measure the dissolved gas concentration in the slurry, and even were it possible, seldom are equilibrium data available with a suitable Henry’s law constant.In general, by assuming a reasonable value for the dissolved gas concentration in the slurry and a corresponding equilibrium gas partial pressure P*, Kga values can be calculated for the pilot plant and scaled up. Then, with the same P* value at various reaction conditions, a mixer can be designed which is quite satisfactory, having a reasonable design factor for full-scale performance.We will take as an example a slurry of a known solids composition and use a continuous 4 tank system. By assuming a percentage saturation of the dissolved gas in the first tank, the dissolved gas concentration can be obtained in the other three tanks. It usually is possible to measure the off-gas composition in each of the 4 tanks. If the top of the tanks is connected in the form of a multi-compartmented horizontal autoclave, then a modified top off-gas composition in each compartment must be used."

Jan 1, 2003

By Johan C. van Dyk, Johan W. van Zyl, Martin J. Keyser

"Coal is a crucial feedstock for South Africa’s unique synfuels and petrochemicals from coal industry and it is used as the main feedstock to produce synthesis gas (CO and H2) via the Sasol-Lurgi Fixed Bed Dry Bottom gasification process. Detailed coal characteristics are essential to predict gasification behaviour when a specific coal source is to be gasified.The principle aim of this paper is to highlight and discuss those specific coal characteristics, which affect gasification behaviour and stability.In order to determine the suitability of a coal source for gasification purposes, the coal is characterized and the results compared with historical data. Benchmark data, where it was possible to operate the gasifier with ease and relatively high stability, is used as a reference.Coal sources with extreme properties (i.e. low reactivity, ash content <10% as is used by Dakota Gasification Company, or “brown coal” with moisture >30%) can probably be gasified in a Sasol-Lurgi Fixed Bed Dry Bottom gasifier provided that certain operational changes are implemented. Other properties, like high caking and extreme ash content for example, require blending to acceptable levels."

Jan 1, 2003

By Jian Zhang, Yongfu Yu, Fuguang Zhang, Liping Che

There is one large-scaled iron ore deposit in Inner Mongolia of China, but it is very complex which includes about 170 types of minerals and 71 elements. The hematite, magnetite are mainly iron ores. It is difficult that the iron mineral can be separated efficiently by common dressing methods due to the complexity, and the iron concentrates in the mineral processing factory contains many foreign substance such as K, Na and Si so that the process in iron mill is influenced because of the foreign substance, so it is vital reducing the foreign substance.

Jan 1, 2003

By Chris A. Fleming

"Interest in the recovery of cyanide from gold and silver plant tailings has heightened in recent years. This interest has been spurred by several factors:Increasingly stringent regulations throughout the gold producing world, governing discharge limits for free and total cyanide to tailings ponds and the environment.The increasing cost of active chemical treatment versus passive (natural degradation) treatment of tailing, to bring them in line with environmental regulations.The worldwide trend to processing of more complex gold ore bodies, which is usually accompanied by higher levels of cyanide consumptions and greater concentrations of cyanide (particularly the copper cyanide complex) in tailings.The growing negative perception of the general public for the gold mining industry, due to several highly publicized cyanide spills in recent years (breaches of tailings dams, accidents involving trucks carrying cyanide to gold plants, etc.).The ability to recover cyanide from gold plant tailings has been known almost as long as the cyanidation process has been practiced, but there has been little incentive to process tailings in this way in the past. With the development of technologies that make it possible to recover and recycle free or complexed cyanide directly from gold plant slurry tailings, which indicates, on paper at least, the potential for significant cost savings compared to cyanide destruction, coupled with the introduction of legislation to seriously limit the discharge of cyanide to the environment in most gold-producing regions of the world, many companies are evaluating the cyanide-recovery alternative."

Jan 1, 2003

By Roberto C. G. Oliveira, Scott C. Brown, Brij M. Moudgil

"The wettability or surface energy of particle surfaces dictates a number of multiphase ensemble interactions that have a significant impact in mineral processing. Dispersion, bulk powder handling and flotation are just a few of the processes that are largely influenced by the degree of hydrophillicity or hydrophobicity on particulate surfaces. Because of the importance of surface wettability, a number of simple, precise and accurate techniques for accessing surface wettability or contact angle on macroscopic flat surfaces have been developed. However, these techniques cannot be directly applied to the particulate surfaces that are often in query. Though a number of techniques are available for accessing the wettability of particulate surfaces, these methods are either relative, application specific or prohibitively tedious. In the present study, key features of existing techniques are combined to formulate an improved method to delineate particle wettability that is simple, versatile and capable of providing reproducible measurements in an industrial environment.Through the use of an inert adhesive and an inert macroscopic surface as a support, it is illustrated that precise measurements of particle wettability are obtainable under suboptimal or ‘shop floor’ conditions. The measurement of the maximum external meniscus height formed between a test liquid and a particlecoated rod is employed to estimate phenomenological contact angles on particles ranging form a few nanometers to several hundred microns in size."

Jan 1, 2003

By Rhulani F. Maluleke, Francis W. Petersen, John H. Marsh, Johann de T. Steyl, Allan Nesbitt

"Pressure leaching of chalcopyrite and nickeliferrous pyrrotite at temperatures between 105 and 200 ºC has been proposed as a potentially viable route for the extraction of mineral elements from sulphide concentrates. In general, these concentrates contain iron, and the economic success of the processes is partially dependent on the choice of the environmentally acceptable iron-removal technique. One of the most widely used methods for the removal of iron from sulphate liquors is precipitation as hematite, goethite, or jarosite. The nature of the iron precipitate formed, dictates downstream dewatering and residue treatment and disposal options. However, a better understanding of iron precipitation under the defined process conditions would consequently be of benefit in process design and optimization.This study investigated the precipitation of iron in the autoclave at temperatures between 105 and 200 ºC. The effects of temperature, acid concentration, iron concentration, and the presence of other metal cations on the nature and composition of the precipitates were determined."

Jan 1, 2003

By T. V. Chnyrenkova, J. Troncoso, V. A. Luganov, G. P. Kluev

"Arsenic-gold bearing ores are used as flux in smelting or are leached out with extraction of gold. For decreasing arsenic content in processed materials and for breaking up the lattice and opening up of gold the raw materials are roasted. Some regularity was established for sulfidizing of arsenic bearing compounds in a presence of pyrite and for oxidation of ores and concentrates in the presence of soda.This article analyses the results of laboratory and pilot testing of dissociating and oxidizing roasting of gold-arsenic bearing concentrates. During the dissociation roasting under vacuum arsenic is sublimated into elemental and sulfide forms. This process allows minimizing the negative influence on the environment but requires costly engineering solutions. Roasting in a limited quantity of oxygen in the gaseous phase makes it possible to sublimate arsenic in the form of oxides and sulfides and may be carried out in fluid bed furnaces."

Jan 1, 2003

By Atsushi Shibayama, Toyohisa Fujita, Luo Lin, Toshio Miyazaki

A novel process is developed in this study for separation of tungsten and vanadium from a leach solution of tungsten alloy scraps. Specifically, a magnesium salt combined ammonium solution is employed to precipitate vanadium and impurities in the purification of the leach solution. This separates vanadium from tungsten by rejecting tungsten in aqueous solution. Finally, tungsten is recovered as the form of ammonium para-tungstate (APT). Vanadium is recovered as the form of ammonium meta-vanadate(AMV).

Jan 1, 2003

By John C. Gathje, Rick Moritz, Wilhelm de Beer, Gary L. Simmons

"Froth flotation has a long history of success for the recovery and concentration of a wide variety of minerals of commercial interest. Both the art and science of flotation have progressed greatly, and as our knowledge has increased so has our ability to improve mineral separations and recoveries.One area of interest in recent years has been the flotation of refractory gold ores to recover the goldbearing sulfides. In many instances, the use of conventional air flotation to concentrate these values has achieved only limited success. However, as a result of intensive research, Newmont Mining has expanded the boundaries of flotation, and it can now be used to successfully treat many gold-bearing sulfide ores as well as platinum and palladium ores. This has been achieved through the use of the patented N2TEC technology, which utilizes nitrogen as an inert gas in the flotation process."

Jan 1, 2003

By Shailin Lalloo, Allan B. Nesbitt

"Gravity separation by centrifugal equipment, particularly in the mineral processing industry is a novel approach of optimising product recovery. The manufacture and sale of centrifugal equipment by recently established companies is now beginning to have a significant impact on the industry. Some benefits of operating at increased gravity include: reduced environmental issues, a shorter lead time, lower capital cost and improved recoveries of elemental mineral before entering the grinding circuit.Of topical discussion is the use of centrifugal separators for the recovery of less valuable minerals that will form a greater proportion of the feed compared to traditional scalping circuits where the gold content is extremely low. This ultimately results in the centrifugal system having to have a greater mass pull. In addition, the relative density difference between gangue and valuable mineral is likely to be less and therefore modelling and optimisation of this separation process will be necessary. Some researchers have muted using fluidisation models to model the forces present in the separation zone of a centrifugal separator2. It is not unusual for the manufactures of centrifugal separation equipment to use fluidisation terminology to describe what happens in the separation zone. Most fluidisation models are based on the empirical/classic relationship between superficial fluid velocity and voidage postulated by Richardson and Zaki. However, no researcher has proved the effectiveness of this relationship in an increased gravity Environment."

Jan 1, 2003

By P. Harris

"Comparison of the two most commonly used classes of depressant in the South African platinum industry is complicated by the fact that these polymers induce different effects on the surfaces onto which they adsorb. The use of carboxymethyl cellulose (CMC), which is ionically charged in solution, can lead to increased particle dispersion in addition to the effect of reduced surface hydrophobicity (depression). Guar is typically only slightly charged in solution. Comparison of these two depressants is complicated since it is uncertain whether differences in their action is a result of either depression of dispersion effects.This work investigates the role of dispersion independently to that of depression in the batch flotation of a platinum bearing ore. An inorganic dispersant, sodium hexametaphosphate (NaHMP) was added in parallel to the uncharged guar depressant to simulate the action of depressants with varying degrees of dispersion. By distinguishing between the material recovered by entrainment and the floatable gangue and by including the effects of froth stability it was possible to decouple the effects of dispersion and depression.The results show that both dispersion and depression led to increased grade of the sulphide minerals. Depression leads to a decreased recovery of floatable gangue minerals. Dispersion leads to an increased recovery rate of these minerals and an accompanying decrease in froth stability."

Jan 1, 2003