Search Documents

By Hideki Yamamoto, Norihiro Murayama, Junji Shibata

"Hydrothermal syntheses of zeolite from coal fly ash were carried out by using various alkali sources. NaOH, Na2CO3, KOH, K2CO3 and their mixture were applied for an alkali source of zeolite synthesis. The various physical properties of the reaction product, such as the kind of zeolite crystal, cation exchange property, surface texture and so on, was investigated through the zeolitization reaction from fly ash. The mechanism of zeolitization reaction was considered from these results.Zeolite P(NaP), hydroxysodalite(HS) and chabazite(K-CHA) are synthesized as zeolite species, when fly ash hydrothermally reacts in various alkali solutions at 393K. The crystal structure of the products obtained in NaOH solutions for 3h changes from NaP to HS with increasing NaOH concentration. K-CHA formation in KOH solutions needs 10h of reaction time, which is longer than that of NaP or HS.Dissolution, condensation and crystallization steps exist in the zeolitization reaction from fly ash, and the particle surface of products remarkably changes in each step. The fly ash is spherical particles and the surface is smooth(Fig.1(a)). The dissolution of fly ash occurs in the heating process until 393K, and the particle surface changes like unevenness(Fig.1(b)). In case of NaP, the condensation of aluminosilicate ions takes place at 373-393K, and the amorphous aluminosilicate is deposit on the unreacted fly ash(Fig.1(c)). The crystallization of NaP already begins to occur at 393K and the surface is covered with fine zeolite crystals for 24h(Fig.1(d))."

Jan 1, 2003

By Hong Zhong, Shuai Wang, Zhanfang Cao, Ting Dai

"Manganese is widely used in industries such as the steel industry and is now an essential element in modern industry. Technologies for the efficient and clean utilization of manganese resources must be developed and employed to ensure the sustainable growth of the manganese industry. Our research focuses on the use of beneficiation technologies to improve the grade of ores or the replacement of low-grade manganese carbonate ores with high-grade manganese oxide ores, and thus, to reduce reagent and energy consumption and the yield of electrolytic manganese residues from metallurgical processes; the study of leachate purification technologies; the study of electrochemical behaviors during electrolysis and energy-saving electrolysis methods; the development of chromium-free passivators as alternatives to the highly toxic potassium dichromate passivator; the non-hazardous treatment and resource utilization of electrolytic manganese residues and other manganese by-products; and the development of new manganese products. INTRODUCTION Manganese is widely used in the steel industry, nonferrous metallurgy, the chemical industry, electronics, batteries, agriculture, etc. Globally, more than 90% of manganese is consumed by the steel industry, and thus, it is said that ""No steel industry without manganese""(Banerjee et al. 2017, Zhang et al. 2017). Current manganese resources mainly include manganese ores, marine manganese nodules and waste catalysts. The total global output of manganese ore from land deposits is 18 million tons (metal volume), and the reserves, most of which is in the form of manganese oxide ores, are estimated to be 620 million tons (metal volume). More than 400 manganese ore deposits with a total reserve of 1.22 billion tons have been discovered in China. These deposits are predominantly manganese carbonate ores. Marine manganese nodules exist on the surface of the deep seabed at depths of 2000-6000 m. These nodules, which are also called polymetallic nodules, manganese balls, manganese aggregates and manganese tumors, are mainly composed of iron and manganese oxides. The total reserves of these resources add up to more than 3 trillion tons. Furthermore, the manganese in manganese-containing catalysts can be recycled after they become inactive."

Jan 1, 2018

By D. R. Nagaraj, Raymond Farinato

Water constitutes one of the most valuable resources employed in mineral recovery and processing. Identifying potential problems encountered in mineral processing in waters unusable for drinking or agriculture (including seawater and even hypersaline waters), understanding chemical factor interactions, and optimization of flotation reagents will greatly expand our ability to create more sustainable beneficiation technologies. The current paucity of our knowledgebase regarding high salinity effects on flotation clearly signals a need for a significant research effort. We report here results of a study designed to probe effects of pulp chemistry on metallurgical performance in the flotation of Cu and Cu-Mo ores in saline waters. The results clearly demonstrate that pH (more correctly dosage of pH modifier to target a pH set point) has the most significant effect on Mo recovery when using seawater. This is linked to the formation/precipitation of Mg(OH)2 when pH = 10.3 (in seawater). The type of pH modifier used, NaOH or Ca(OH)2, had no impact on Cu or Mo recovery, indicating that Ca2+ ions were not involved in any reduction in Mo recovery in the pH range of 9-11. Our results in tap water spiked with either Ca2+ or Mg2+ ions in the same pH range (controlled by NaOH), confirmed that Ca2+ ions had no effect on Cu or Mo recovery, but that addition of Mg2+ ions had a severe adverse effect on Mo recovery at pH = 9.5, and to a lesser extent on Cu recovery. The onset of Mg(OH)2 precipitation occurred at a higher pH, and the adverse impact of Mg(OH)2 on Cu recovery (and perhaps Mo recovery as well) was less, in sea water than in tap water spiked with Mg2+. These effects are attributed to the mitigating role of the high electrolyte concentration, notably NaCl.

Jan 1, 2014

By Y. S. Sun, P. Gao

Compared with conventional roasting and magnetic separation processes, higher reduction temperatures and stronger reducing atmospheres are used in reduction technologies to reduce iron oxides to metallic iron, which is often liberated during reduction and amenable to magnetic separation. Reduction and magnetic separation of an Australian refractory iron ore was therefore studied as a function of reduction temperature, time, coal addition, feed thickness and size of Australia iron ore. It was found that during reduction, the particle size of the reduced iron increased with reduction temperature and time. Subsequent magnetic separation tests were further conducted on the reduction products. A reduced iron powder with a Fe grade of 85.67% was obtained at a Fe recovery of 87.82% under optimum reduction conditions where a metallization rate of 85.82% was achieved. The mechanism involved in reduction is discussed based on XRD and SEM examinations. And the results indicated that theiron minerals such as hematite and limonite in the Australian iron ore were reduced as follows: Fe2O3?Fe3O4?FeO?Fe. Furthermore, the metallic iron particles produced by reduction increased in size with longer reduction times.

Jan 1, 2014

By A. I. Urvanzev, N. V. Shikhov

"In this paper, we present the study’s results of electrical separation processes on the basis of new separator designs, new technological solutions, and newly discovered effects. We considered the options of enrichment by magnet separation of magnetite and titanomagnetite ores, ores and products containing chromium and manganese, ores of non-ferrous and precious metals. During pneumo-electric separation of mixed iron ore of SMPC, 43.3% of the output of the concentrate with an iron content of 61.7% was obtained in one step, with extraction of 70.5%. The paper also presents the results of the finalization on the air-electric separator of the magnetic fraction when separating oxidized ores of MPPOO (mining and processing plant of oxidized ores) on the Jans polygrade magnetic separator. A concentrate was obtained with an iron content of 65.1% with the extraction of 95.0% and tails with an iron content of 13.0%. The possibility of obtaining low-silica concentrates from these ores with an iron content of 67.15 and a quartz of 2.88% is shown. Also, the results of tests on the enrichment of chromite ores on the firing-magnetic scheme with corona-electrostatic separation are considered. On the initial ore of the Don MPP (mining and processing plant), a concentrate with a content of 61.8% Cr2O3 was obtained with a quartz content of ~ 1.0%. The results of pneumo-electric separation with triboelectric charge of the separated particles are presented. The results of the tests indicate a principal possibility of enriching chromite ores without costly high-temperature roasting. Dry technology of enrichment of manganese ores with the use of electrical separation increases the quality of the oxidized concentrate to the first grade and raises the total extraction by 2 times. For the Chineya deposit of titanomagnetite ores with copper impurities, electroseparation operations were carried out on two samples with a Cu content of 1.93 and 3.75%, respectively. For a sample with a Cu content of 6.02%, a copper concentrate output of 24.42% was obtained with a Cu content of 23.82% and the extraction of 94.88%. The results of enrichment by electroseparation of gold-containing sulfide ores can have the practical importance. For ores of the Berezovskoye deposit, a pyritic concentrate containing 100 g / t of gold was obtained after two or three operations of IES (integrated energy systems)."

Jan 1, 2018

By William Skinner, Jonas Addai-Mensah, Keith Quast, David Robinson, Jason Connor

A review of the laboratory- and pilot plant-scale physical separation techniques for the beneficiation of nickel (Ni) laterites shows limited efficacy. To date, the only upgrade technique adopted commercially, prior to hydrometallurgical processing of Ni laterites, is the removal of a barren, coarse size fraction in the feed by classification. In the present work we investigated two low grade (~ 1%), goethite-rich Ni laterite ores’ upgrading by magnetic separation, attritioning/coarse, (lower Ni-grade) gangue rejection and flotation techniques. Low intensity (0.1T) dry magnetic separation at ambient temperature of raw samples and those pre-heated at temperatures up to 450 °C showed evidence of pay metal Co and Mn bearing asbolane and/or lithiophorite minerals pre-concentration in the magnetic fractions. Ni distribution, however, did not show any noticeable magnetic upgrade but followed the weight distribution. Other ore pre-treatment methods (e.g., desliming and sulphidisation) followed by froth flotation with anionic and cationic reagents also led to noticeable (~35%) Ni upgrade. This is due to the deportment of Ni across several gangue host mineral phases (i.e. Fe oxide/hydroxide and a range of silicate/aluminosilicate minerals). From chemical analysis, after disaggregation of ~ 1% Ni grade feed ore, coarse (-600 + 38 µm) and fine (-38 µm) fractions of ~0.6% and 1.3% Ni grades respectively, were also produced, suggesting that a significant upgrade in Ni content can be achieved by rejecting the + 38 µm fraction with the loss of <40% of the Ni. The ore mineralogy, particularly the complexity and high number of un-liberated Ni-bearing phases, greatly compromises physical separation methods for these ores, with the possible exception of screening after disaggregation of the fines inherent in the run of mine ores.

Jan 1, 2014

By Héctor X. Toro, José Francisco Cabello, Douglas Batista, Álvaro Videla, Claudio Luiz Schneider

The Minas-Rio Project, located in the state of Minas Gerais, Brazil, is currently under construction. The new plant will have a regrinding circuit that uses VertimillTM. The objective is to process itabirite iron ores and it is expected that the consumption of media will represent a large part of the plant operating cost. Many studies in the literature indicate that the size of the grinding media directly influences the grinding efficiency. The size distribution of the charge media is related to the surface area of the charge. In this study, a sample of itabirite iron ore was tested with respect to grindability in a laboratory scale ball mill. The test mill was equipped with a torque device to accurately measure power consumption, as required for the determination of energy specific kinetic parameters. Five tests were carried out with different sizes of steel balls and with SICAM (sub-inch Cast Media). The size distributions of the feed and product of the several grinding tests were used to calibrate population balance model parameters for each condition. The results confirmed that the ball charge with smaller diameter is the most efficient among the different media charge tested.

Jan 1, 2014

"The most common agglomeration technique in iron and steelmaking is sintering, which requires the use of iron ore/concentrate mixtures, limestone and dolomite as fluxes and coke as fuel in order to produce the required melt at high temperature to cause agglomeration of the particles. Sinter feed blends containing high proportions of magnetite concentrate are difficult to granulate and to produce granules of high permeability, and sufficiently robust quasi-particles for successful sintering operations. Since the granulation of iron ore sinter feed requires no use of a binder, the added fluxes play a vital role in holding the granule particles together until they sinter. The fluxes also help to improve the granule quality and control slag composition in the blast furnace. It is well-known that the particle size distribution of the fluxes affects the granulation effectiveness and green bed permeability which determine the productivity, physical and metallurgical properties of the granules and sinter. Hence it is necessary to understand the role of flux particle size on granule properties so as to improve the granulation of iron ore sinter feed blends containing high magnetite concentrate. In this study, laboratory granulation experiments have been carried out on iron ore sinter feed blends containing high proportions of magnetite concentrate at different addition levels of limestone and dolomite mean particle sizes, to understand the influence of limestone and dolomite particle sizes on granulation rate processes and granule properties.INTRODUCTION Increases in iron ore production to meet the global demand for iron and steel products has led to the depletion of high grade iron ores and thus the current utilisation of low grade iron ore fines and concentrates. However, sinter, pellets and the lump are the required feed types used in the blast furnace. The high basicity sinter is the main iron bearing feed accounting for 70-85% in the blast furnace due to its good metallurgical and mechanical properties that allow high productivity, efficient processes and low production cost (Adam et al., 2017)."

Jan 1, 2018

By Z. S. Abisheva

Results of the study targeted to development of universal acidic-extraction-precipitation technology for gallium recovery from the sublimates are presented in the paper. This will let to utilize a new non-traditional source for gallium production. Phase composition of gallium containing dust was studied. Forms of gallium in the sublimates were determined. The main form is Ga2O3, however, GaP form is also present in the cottrel dust and Na5Ga3F14 form is present in the dust of aluminum electrolysis. The possibility of gallium concentration was established via secondary pyro-selection of the dust. Kinetics of interaction of dust components with sulfuric acid was studied. The products of the interaction subsequently were leached with water. Optimum conditions for direct leaching with HCl and H2SO4 were determined providing gallium recovery from the cottrel dust and the ash carry outs up to 95 %. Gallium recovery from the primary dust and the secondary dust of aluminum electrolysis was at 52; 64 % and 63; 83 % respectively. Effect of Fe, P, K, Na and Al admixtures for gallium extraction from hydrochloric acid solutions was studied. It was shown that gallium chloride complex (GaCl4-) is extracted into the organic phase from the following acid mixtures: HCl + H2SO4, HCl + H3PO4, HCl + H2SO4 + H3PO4, HCl + HF. Kinetic regularities of gallium extraction in the system (tri butyl phosphate) TBP ? HCl - Ga were studied using diffusion cell method with agitation. Optimum conditions for gallium extraction from complex hydrochloric acid solutions with TBP were found providing 99.9 % recovery and separation coefficient for gallium and iron (III) of more than 25 in one stage. Sodium hydroxide and water were selected as reagents for re-extraction of gallium from the organic phase. Different options for disposal of by-products that are formed in the processing of cottrel dust, ash sublimates and dust of aluminum electrolysis were proposed and tested. Keywords: gallium, kinetic, sulfatization, leaching, extraction, technology

Sep 1, 2012

By S. Q. Zhu

Coal Water Mixtures (CWMs) are densed suspensions of coal particles in water. Viscosity is one of the most important rheological properties of CWMs and it is desired to be as low as possible. The slurry viscosity was influenced significantly by additive formation, the particle size distribution and the ash content of the coal. However, the influence of dispersants is most obvious. At present, there are several kinds of dispersants such as polymeric styrene sulfuric sodium, lignin sulfonate, humate, polycarboxy salt, ethylene epoxide surfactant. In this paper, a newly synthesized CWM dispersant has been reported, which is an efficient anionic surfactants of polycarboxylic acid type. The synthesis process includes three steps. At the beginning, the polyglycol acetate ester has been performed by acetic acid and polyethylene glycol (PEO) on the condition of acetic-acid/PEO ratio 1:1.1, at 368~373K for 30 minutes. Then the macro-monomer is prepared through the esterification of 85.71% acrylic and 14.29% polyglycol acetate ester, at 368~373K for 10 minutes. After that, the polycarboxylic acid CWM dispersant is polymerized using proper proportion macro-monomer, acrylic (AA) and sulfonic styrol sodium, at 368~373K for 1 hour. This new dispersants are used in the coal water mixtures formulation. Four kinds of coal used in the experiment are Shuang Yashan, Tunliu, Luning, Changcun samples. ? The highest concentration for shuanyashan coal is 70% when the dosage of dispersant is 0.4%, and the content of -200 meshes particles is 75.53%. As the dosage of dispersant de-creases to 0.25%, the Shangyashan CWM concentration is 67%. ? For Tunliu coal CWM concentrations are in the range of 76% to 75% when dosage of the dispersant changes from 0.4% to 0.25% at the same particle size distribution of 83.5% minus 200 meshes. ? The highest concentration for Luning coal is 69% when dosage of the dispersant is 0.4%, and the content of -200 meshes particles is 88.86%. ? For Changcun sample, the coal concentration of CWM is 73%~75% when dosage range of the dispersant is 0.35%~0.5%. The experiments show that the synthesied dispersant is quite promising for some coals CWM preparation, but a little bit coal-dependent. The Proximate and Ultimate analysis, surface characteristic measurement have been made to investigate the interactions between coal and additives.

Jan 1, 2014

By S. Banisi, A. Ghasemi, S. Zare, F. Ghorbani, E. Nematollahi

"Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Working at the maximum operating capacity of comminution equipment plays a significant role in the efficiency of the circuit. Appropriate design of cone crusher feed box could result in the choked crushing which is known as a vital factor in achieving target performance. In this research, the non-uniform cone crusher feeding at the Sarcheshmeh copper complex was studied and appropriate measures were taken to solve the problem. The problem resulted in non-uniform and high wear rate of crusher liners and high fluctuations of power draw. In recent decades, the discrete element method (DEM) has been applied successfully to study the effect of different factors on the behavior of particles flow. In this work, various designs for feed box were tested using an in-house developed DEM software called KMPCDEM©. The best feed box design obtained from the simulations was selected, constructed and installed in of the cone crushers. The new feed box design resulted in more uniform feed distribution on the distributor plate of crusher indicated by a reduction of the standard deviation of power draw measurements from 13 to 3 kWh. The better control of the crusher, 49% increase in the crusher throughput and finer and narrower product size distribution were the main outcomes of the installation of the new feed box. Furthermore, the wear rate on mantle and liners of crusher not only decreased but it also became uniform.INTRODUCTION Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Reaching the maximum operating capacity in comminution equipment is a key sign of approaching the nominal productivity of the process. Due to the effect of crusher efficiency on the downstream circuit performance, optimization of the crushing circuits has received considerable attention (Herbst, & Potapov, 2004; Quist, & Evertsson, 2010; Li, Huiqi, McDowell, Glenn R, Lowndes and Ian, 2014; Cleary, Sinnott, Morrison, Cummins, & Delaney, 2017). Improving the performance of crushing circuits not only decreases the capital and operating costs but also increases the efficiency of downstream grinding circuits (Jacobson, Janssen, & Urbinatti, 2010). In cone crushers particles can be subjected to two different modes of compressive breakage; single particle breakage (free feeding) and inter-particle breakage (choked feeding). The maximum efficiency of the cone crusher directly depends on the type of feeding arrangement (Operation Manual, 1977). An appropriate feeding must lead to choked feeding the cone crusher. If the rate and method of feeding the crushers are correctly be executed, the maximum efficiency of the crushers could be available (Jacobson et al., 2010)."

Jan 1, 2018

By Nina Panteleeva, Elena Afonina, Stanislav Titkov, Jury Buksha

"Flotation processing of water-soluble minerals (potassium ores, sedimentary salts of salt lakes) is currently the main method for production of potassium fertilizers and concentrated carnallite which is the initial product for production of metallic magnesium. Flotation of sylvite (KCl) and halite (NaCl) is carried out in the electrolyte solutions: KCl-NaCl-H2O and KCl-NaCl-MgCl2-H2O. The report presents the results of studies of the effect of concentration and the electrolyte type on the size of air bubbles in a flotation cell in comparison with the floatability of mineral constituents of potash ores. The floatability in electrolytes of various compositions has been studied: - of sylvite (KCl) by alkylamines, - of halite (NaCl) by alkylmorpholines, - of silicate-carbonate slimes contained in the ore by ethoxylated surfactants. The reagent modes (regimes) activating the flotation desliming of potash ores have been developed."

Jan 1, 2014

By V. F. Petrov, O. D. Khmelnitskaya, V. M. Lodeischikov

"The processing of copper gold ores is one of the major issues of gold-mining industry in the beginning of 21st century. In this case, application of ammoniacal cyanidation process for this type of mineral raw materials deserves special attention. Irgiredmet Institute has carried out a wide range of studies on ammoniacal cyanidation process and evaluated the possible commercial use of this process for Russian operating plants. Copper gold-bearing ore from a current Russian deposit was studied. The content of gold and copper in the ore is 9.4 g/t and 0.4%, respectively. Based on the results of preliminary test work, a flow sheet was developed. It included gravity concentration followed by cyanidation of the gravity tailings using CIP. The flow sheet provides sufficient total gold recovery (91.5%). However, this technology has disadvantages, such as high specific consumption of reagents: 4.5 kg/t NaCN and 13.5 kg/t Ca(OCl)2 the ore and the increased gold grade in the liquid phase of the tails slurry (0.2 g/t). In order to improve cyanidation process parameters, test work on gravity tails processing using ammoniacal cyanidation was carried out. After the test work was completed, ammoniacal cyanidation flow sheet for copper gold-bearing ores was developed. Leaching conditions were optimized using recycled process solutions. Recommendations on gold recovery from the solutions and tails detoxification are given. The proposed flow sheet provides 91.5% gold recovery. In this case, compared to the conventional option, the consumption of cyanide decreases by 3-4 times.INTRODUCTION The technology of precious metals recovery from gold-bearing ores is based on cyanidation. This accounts for up to 90% gold recovery and the significant portion of silver (Lodeischikov, 1999). However, there exists the category of so called refractory ores. They are not amenable to direct cyanidation (without using additional expensive processes), or they are characterized by low indices of metals recovery and high consumption of reagents. The latter also include copper gold ores. Their deposits can be found extensively both worldwide and in Russian Federation. A feature of these ores is that they contain not only gold but also copper. It is considered not only as a valuable component but also as a harmful mineral impurity that hinders gold cyanidation, gold precipitation from the solutions by cementation onto zinc dust and adsorption onto activated carbon (CIL, CIP-processes), detoxification of cyanide bearing effluents."

Jan 1, 2018

By Polezhaev S. Yu, I. V. Ukraintsev, Boduen A. Ya, Saburbayeva L. Yu

"Comparison studies of different technologies are performed when selecting optimum option for gold ore and concentrate processing. Methods of ultrafine grinding, oxidizing roasting, bacterial leaching and pressure oxidation are used to extract gold from refractory ores and concentrates. Refractory gold flotation concentrate produced from pyrite-arsenopyrite ores of Bestobe deposit is a case study in this paper. The results of the experimental tests of the direct leaching of flotation concentrate and pre-oxidation products using different methods (oxidizing roasting cinder, pressure oxidation and bacterial leaching cakes) are the following: - cyanidation of original flotation concentrate provides recovery of Au at 46.6 %; - oxidizing roasting increases gold recovery from 46.6 % to 85 %; - BIOX increases gold recovery up to 86 %; - preliminary pressure oxidation of flotation concentrate ensures steadily high Au extraction in the follow-up cyanidation at 94.9-96.5 %. Pressure oxidation and bio-oxidation has changed dramatically the strategy of refractory gold ore processing. These solutions provided for development of ore deposits that considered earlier non-commercial. However, refractory ore processing has a complex character in terms of developing process flowsheet and requires large amount of studies to be performed for each new project. Gold extraction is the basic but not the only criteria to technology selection for gold ore and concentrate processing. Opex and capex, ore reserves, regional geography, developed infrastructure and skill personnel should be considered. Process studies and feasibility study of the developed technology shall be provided for each specific gold ore deposit. INTRODUCTION Due to changes in available feedstock and depletion of easy-to-process ores, refractory ores containing finely disseminated gold and silver in sulphides (primarily, in pyrites and arsenopyrites) are more and more involved into processing. Experts say that such ores amount above 40 % of the world’s gold reserves. Conventional technologies of gold extraction from refractory ores include flotation, roasting and cinder cyanidation (Fraser etal., 1991). However, today’s best available practice for refractory gold ore processing are bacterial (BIOX) and pressure (POX) oxidation."

Jan 1, 2018

The quality of iron ore fines in terms of high iron content and low levels of deleterious impurities such as Silica, Alumina, Sulphur and Phosphorous is a critical parameter, in sintering and subsequent iron and steel making processes. As the higher-grade ores become depleted, there will be a stronger focus on treating lower-grade haematite/goethite ores and developing suitable beneficiation techniques to reduce the levels of impurities. Innovative flow sheets, based on new and commercially available technologies, is required. These will be needed to include gravity concentration devices, which can handle coarse and fine feed sizes. In this paper, efforts made to reduce the silica and alumina content of a low grade iron ore fines (<1.0 mm size) sample from the Pilbara region in Western Australia are described. The feed sample, a goethite abundant lower grade iron ore fines, which was a plant reject assaying 48.66% Fe with 13.61% SiO2and 5.09% Al2O3 was investigated. To this end, an experimental campaign was undertaken, and beneficiation studies were conducted on the sample using a Floatex Density Separator (FDS), a gravity device which can be operated for size classification and/or relative density separation. The objective was to produce high-quality iron ore material suitable as sinter feed. An iron concentrate with a grade around 57.0% Fe (Calcined Fe of about 63.0%) was achieved while recovering around 67.0% of the feed weight. In addition, a rejection of substantial content of Silica (>75%) and Alumina (>66%) was achieved while securing >77% iron recovery. On the other hand, sharp classification efficiency with low values of imperfection around 0.20 was obtained. Consequently, the response of the lower grade iron ore sample to FDS application, has vast potential to reject deleterious impurities as a single stage separating beneficiation equipment. Remarkably, it was demonstrated, that a great amount of goethite, abundant in lower grade iron ore fines/plant rejects, which are currently being either stockpiled and/or dumped as waste, can be treated using FDS application and potentially can add a significant value to the iron ore mining industry by recovering additional iron ore fines. Keywords: deleterious impurities, beneficiation techniques, classification, relative density separation

Sep 1, 2012

By John O. Marsden

"Technology development and innovation has played a crucial role in the copper industry throughout history. The effective development and implementation of new technologies allows mankind to produce copper at progressively lower cost of production at a given feed grade and mineral type. This progress serves to counteract cost inflation/escalation over time and, depending on the magnitude of the cost benefit, allows ore cut off grades to be reduced thereby improving the availability, accessibility and utilization of resources. Two broad categories of technology development and innovation play a key role in this process: (i) incremental improvements and optimization of existing technology provide benefits in the near- to medium-term, and (ii) step change technologies provide value over the longer term. A key issue for potential developers and implementers of new step change technology is how to justify resource allocation and expenditures for such initiatives. This paper examines this issue with reference to specific case studies in the copper industry. INTRODUCTION AND BACKGROUND Technology development and innovation has played a crucial role in the commodity minerals industry throughout history, and none more important than the copper industry. As new, cost-efficient technologies are commercialized, the cost of production in real terms at a given ore feed grade and mineral type decreases. This progress enables ore cut off grades to be reduced allowing lower grade material to be processed economically, which in turn increases the availability and supply of the metal or mineral of interest. Cost inflation/escalation works in the opposite direction, squeezing margins for operations utilizing incumbent technology to process material from a given ore deposit. A prior review by the author considered the issue of technology development and sustainable competitive advantage. This review concluded that first movers and fast followers can achieve competitive advantage for periods of 10-15 years through effective deployment of new technologies (Marsden, 2004). A new, more comprehensive study and evaluation was completed in 2014. This paper presents a portion of the results from the 2014 study."

Jan 1, 2018

By S. J. Liu

The conventional collector for bauxite mineral is oleic acid, which is highly insoluble and must be used in high dosage in bauxite flotation operations, that is the great drawback of oleic acid in use. A series of hydroxamic acid were synthesized, and their collecting ability to certain minerals in bauxite: diaspore, kaolinite were studied. The collecting power of various reagents to diaspore in an incremental sequence were shown as follows: benzyl hydroxamic acid<amylic hydroxamic ac-id<heptylic hydroxamic acid<oleic acid<octylic hydroxamic acid; while the incremental sequence of the collecting power to kaolinite was like this: benzyl hydroxamic acid<amylic hydroxamic ac-id<heptylic hydroxamic acid<octylic hydroxamic acid<oleic acid. It could be seen that octylic hydroxamic acid had the capability of high collectivity and good selectivity, and octylic hydroxamic acid was chosen to use in the following experiments. Reduced zeta potential showed the adsorption of the anionic collector on the mineral. By the adsorptive capability and IR tests, the adsorption of octylic hydroxamic acid on diaspore was determined to be chemical absorption, which was greater than that of oleic acid, as it was physical absorption. Results of floatation experiments on manually mixed minerals indicated that the collectivity and selectivity of octylic hydroxamic acid were better than oleic acid.

Jan 1, 2014

By E. P. Olberg, A. Yu. Chikin, S. V. Petrov, M. P. Belykh, N. L. Belkova

"Bacteria that grow in autochtonous communities of gold heap leaching (HL) wastes are adapted to high concentrations of contaminants and environmental conditions. An example of a mine in the Sakha (Yakutia) Republic showed that the bacterial factor had a significant influence on cyanide breakdown and copper and nickel removal in the conditions of HL ore pile zoning compared to chemical oxidation. The diversity of bacterial communities growing in natural and simulated conditions of a HL ore pile was determined for the purpose of the study. The identified bacterial communities included genus Achromobacter and Serratia, which were found to be adapted to a wide range of temperature and can be considered as potential microorganisms for detoxification of gold HL wastes. INTRODUCTION Technologies and systems of passive treatment are of a special interest in relation to solving environmental problems of gold HL wastes detoxification, when neutralization time is not considered as a limitation (Alvarez et al. 2005). Passive treatment methods are based on reagentless spontaneous breakdown of cyanide caused by natural factors, including activity of autochthonous bacterial communities. Implementation of a reagentless biodetoxification technology for mature HL operations provides reduction of environmental impact on industrial site locations and substantial economic benefits compared to conventional chemical processes of neutralization that prevail in the Russian Federation territory. Passive treatment of cyanide-containing wastes was investigated by M. Botz, T. Mudder, S.V. Petrov, L. Simovic, A. Smith, C.A. Young etc. However, the bacterial factor (autochtonous bacterial communities) role in this process is practically unexplored. Thus, the aims of the study included the investigation of a bacterial factor influence on passive treatment of gold HL wastes and the identification of functional groups of bacteria involved in passive treatment."

Jan 1, 2018

By Y. S. Sun, P. Gao

"In this investigation, a pilot-scale suspension magnetization roasting reactor was introduced and used to enhance magnetic properties of an iron ore. Consequently, the effects of roasting temperature, reducing gas CO flow rate and fluidizing gas N2 flow rate on the magnetization roasting performance were investigated. The results indicate that the hematite and siderite are almost completely converted into magnetite by a gas mixture of 3.5 Nm3/h CO and 2 Nm3/h N2 at roasting temperature of 520 °C. Under the optimized conditions, the magnetic iron concentrate with an iron grade of 60.18% and iron recovery of 90.17% was achieved. The XRD and Fe mineral phase analyses revealed that most of the hematite and siderite were converted to magnetite, and the magnetic properties were greatly enhanced. INTRODUCTION The steel and iron industry in China has rapidly developed in recent years requiring a large quantity of iron ores. Low-grade and complex iron ores are currently the overwhelmingly dominant mineral resource for iron in China. Therefore, China depends on imported iron ore resources heavily, resulting in an increase in the production costs of iron-making and steel-making[1-3]. Using domestic resources to produce a steady supply of high-quality iron ores is an important step toward the sustainable development of the steel and iron industry[4-5]. The iron ore from Jiuquan iron and steel company is abundant and recognized as typically complex iron ore resources in China. Magnetization roasting followed by low-intensity magnetic separation has been proven as the most feasible methods to upgrade refractory iron ore[6-10]. In present research, an innovative roasting technology, namely suspension magnetization roasting, was developed and applied to recover iron from a typical refractory iron ore. Suspension magnetization roasting technique and equipment developed by Prof. Yuexin Han’s Group at Northeastern University (NEU) is an effective way for the utilization of refractory iron ore. The advent of suspension magnetization roasting will, in China and even globally, produce a significant technological revolution in the field of iron ore beneficiation. Based on the previous works, this paper mainly described experiments on the separation and recovery of iron from a complex refractory iron ore by means of suspension magnetizing roasting and low-intensity magnetic separation processes. The purpose of the research is providing a new technology for effective utilization of refractory iron ore. Process parameters that affected the separation and recovery rate of iron were conducted and optimized, and the reaction process was analyzed by XRD and Fe mineral phase analysis."

Jan 1, 2018

By T. Sun, J. Kou, C. Sun, D. Gong

"HPGRs (high pressure grinding rollers) have demonstrated higher energy efficiency than conventional comminution equipment due to their application of particle-bed breakage mechanism. In the past decades, a large number of studies have been conducted to understand the characteristics of particle-bed breakage, however, few of them concerned the difference between single-particle and particle-bed breakage in compression comminution. This comparison is able to demonstrate possible advantages of particle-bed against single-particle in a breakage event due to the isolation of the effect of force loading mechanism. The present study investigated progeny fragment size and energy efficiency of these two breakage methods at variable energy inputs and particle sizes. The results show that at low energy inputs of around 0.25 kWh/t, the numbers of fines resulting from the two breakage methods are very similar. However, at higher energy inputs of around 1.0 or 2.0 kWh/t, particle-bed breakage generated significantly more fines. From the perspective of newly generated surface energy, particle-bed breakage is obviously more energy efficient than single-particle breakage at energy inputs between 1.0 and 2.0 kWh/t. It was also found that HPGRs demonstrate high energy utilization rate in generating new surface energy within their typical range of specific energy input. INTRODUCTION Rock comminution is an important and energy-intensive process in mining operations. Nowadays, decreasing head grade and mineral liberation size of ore deposits greatly increase the energy cost of comminution process. HPGRs have been successfully applied in the mining industry to improve the energy performance of comminution circuits. Typically, 10 to 30% of energy saving can be achieved due to the application of HPGR (Wang et al., 2013; Casteel, 2005; Günter et al., 1996)."

Jan 1, 2018