Search Documents

By R. Venugopal

Hydrocyclones have been used extensively for more than 100 years to classify mineral slurries for recirculation in grinding circuits. Sometimes hydrocyclone classification is carried out in more than one stage to improve the efficiency of classification. Factors affecting separation efficiency include fluid velocity, density, and viscosity as well as the mass, size, and density of the particles. The geometric configuration also affects its efficiency; it includes parameters like cyclone diameter, underflow and overflow diameter, position of vortex finder, height of the cyclone, feed inlet geometry, and diameter etc. Besides changes in the basic parameters some modifications in cyclone has also been introduced from time to time which have affected its efficiency, some of these are :-(i).Introduction of magnetic force along with the centrifugal and drag force to control the flow of the magnetic particles inside the chamber.(ii). Introduction of sparger, air is introduced in the chamber in the form of bubbles, to control the flow of fine particles and hydrophobic particles. (iii). Introduction of dilution technologies for the dilution of thickened underflow. (iv).Introduction of new model. In spite of wide use and simple geometry, the real working principle of hydrocyclone chamber is extremely complex because of the swirling turbulent flow inside the device. In order to get more knowledge about hydrocyclones and to increase its efficiency, past 10-15 years simulation techniques are being developed. The simulation models also enabled a deeper insight into the static and dynamic behavior of hydrocyclones. Therefore, more emphasis on simulations by methods like Computational Fluid Dynamics (CFD), Finite Element method (FEM) is given. Overall, a status review of the work carried out on the analysis of hydrocyclone performance, modeling approaches and its contribution in the efficiency of mineral processing operation is highlighted.

Sep 1, 2012

By Ritva Tuunila, Antti Häkkinen

"Wet stirred milling is one of the most effective grinding methods in producing very fine powders in large scale production, but it is a very energy-intensive process, especially when pigments or even nanosize particles are produced. Therefore, optimization of the process parameters is important. The specific energy consumption is a function of stress energy, which describes the effect of tip speed and media characteristics on grinding, and is related to the number of stress events during milling. In effective grinding, a large number of stress events are necessary. The stirrer configuration influences the number of stress events and their intensity, because the motion of the media and the suspension are caused by a rotating stirrer. The effect of three different stirrer types: a pin, disc and blade stirrer, on the grinding rate, i.e. product fineness and specific energy were investigated in this study with a batch laboratory stirred mill with two tip speeds. The material used in the experiments was calcium carbonate. The results obtained with the smaller tip speed showed approximately similar grinding rates and energy consumption for all stirrer types. When looking in closer detail, the blade stirrer seemed to give the finest product with all grinding times compared to the pin and disc stirrers, which both produced almost the same product fineness with the same grinding times. The specific energy consumption was the smallest with the disc stirrer, but not very big differences were obtained. With a higher tip speed, greater differences occurred both in grinding rates and specific energy consumption. The blade stirrer was the most effective in grinding, and the pin stirrer the next. The net energy consumption for the blade and pin stirrers was almost the same, but it was slightly higher for the disc stirrer."

Jan 1, 2014

By W. Z. Yin

It is investigated systemically in this paper that the granularity of the precursor, ZnC2O4?2H2O, is influenced by synthetic conditions. Instantaneously adding of precipitation agent is able to control the mean size of precursor ZnC2O4?2H2O under 300nm, which has great function to obtain well-dispersed ZnO nanoparticles in the next step, pyrolysis. The pyrolysis kinetics model of ZnC2O4?2H2O powder is obtained. Two steps take place during the pyrolysis. The first is dehydration, which the pyrolysis kinetic model is 2(1-a)2/3(chemical reaction), A=8.3×108s-1, E=(75.82±3.00) KJ/mol. The second is formation of ZnO, which the pyrolysis kinetic model is (1-a) (random nucleation and latter growth), A=8.45×1028s-1, E=(360.54±12.00)KJ/mol. ZnO nanoparticles obtained by pyrolysis take on self-growth behavior. It is resulted that for precursor ZnC2O4?2H2O pyrolysis time takes obvious influence on the partilces size under 420?, 500? and 600?. Finally, a new flow sheet for synthesis of ZnO nanoparticles is investigated, in which blendes is used as raw material and hydrometallurgy is introduced into it. The whole flow sheet has no industrial wastes, that is all byproducts can be used in the flow sheet recycled, resulted in the de-crease of productive cost and industrial wastes.

Jan 1, 2014

By Jyotirmoy Sarma

The surface-active agent, like sodium humate, in the present systems produces a very stable suspension. Saline water up to 15% is used as a flocculating agent for recovery of water from the dispersed phase containing 1% solid. The recovered water in the presence of humate at different concentrations (0.05-0.2%) and at pH 8 also produces a stable dispersed phase of iron ore fines and tailings. The beneficiation techniques adopted in the present systems can increase ~ 2-3% iron value in the concentrate of iron ore fine, however, for tailings the increase in iron value is not observed. Keywords: beneficiation, flocculation, iron ore fines, tailings, saline water, surface-active agent

Sep 1, 2012

By M. Bhartia

India is the 5th largest producer of steel in the world and is slated to produce more than 180 Mt by 2020. Expectedly about 50 % of this would be through the Blast furnace route and the rest through Sponge iron / DRI route. Considering that there will not be any major change in iron making technology by that time, the Blast operation would require lump ore (10-40mm) with around 64% Fe grade and sinter fines (<10mm) with 60% Fe (min) as its feed. DRI process would need calibrated ore of size 5-18 mm as the most suitable size of feed. It is also expected that of the total requirement of ore for the DRI route a significant part would be DRI pellets. In India, there is considerable debate going on regarding the technology to be adopted for the processing of iron ore and there is a lack of clear consensus. The above scenario indicates that the processing requirement of iron ore in the country would involve both washing technology as well as beneficiation technology. CDE Asia Ltd is in the forefront of iron ore processing in the country and the experience gained by the company over the last few years of functioning has led the company to believe that route to be adopted depends on the end product requirement and the starting grade of the feed. Keeping in mind the nature of the feed required for the Blast furnace & DRI operation; it is obvious that good washing technology would be highly beneficial to the iron ore industry. Depending on the grade of ore available the limits of washing will be decided and equipment for lump ore beneficiation such as jigs could be incorporated into the washing circuit. Scrubbing of ore either before washing or selectively scrubbing the lumps could be necessary. Very low grade ore and jig rejects would be required to be totally ground and beneficiated for the production of pellet feed in order to utilize the iron ore resources entirely. Another source of ore for pelletisation would be slimes generated from the washing process as well as the huge quantities already available in the tailings dams in the operating mines. Deslimimg and magnetic route of beneficiation could release at 30-40% of the Fe locked up in these tailings ponds/dams. The paper describes the concept with examples from operating plants and proposes how the adoption could be engineered through test work and proper plan of integration. Keywords: washing, beneficiation, iron ore, lumps, sinter fines, pellets, jigs, screens, evowash, nanowash, thickeners, log washers, drum scrubbers

Sep 1, 2012

By Lilong Huang, Xiang Zhao, Yuan Long, Li Shi, Guowang Zhang, Xiao Xiao

"Vertical stirred mill is expected to upgrade the iron concentrate by further size reduced efficiently. The tests for fine grinding of iron ores from Baiyun Boyu iron ore, Baogang Goup, iron contained tails of Cu-Pb-Zn ore in Wanguo ore, Xiaoshalong iron ore in Qinghai were conducted in this paper. The data of appropriate grinding fineness, optimum grinding conditions and energy consumptions obtained from the test were used to select appropriate scale of the vertical stirred mill, optimize the parameters of the grinding process and upgrade the iron concentrate of the iron ore dressing plant or design the new ore dressing plant. Based on the laboratory tests, industrial system of regrinding and magnetic separation with vertical stirred mill as the regrinding mill in micro-fine grained iron concentrate upgrading has worked out very well. The grade of Fe in iron concentrates has increased to about 65.0% (by 4.0~6.5 point percent) when the iron concentrates were reground to designed fineness and the specific energy is 5.0~7.1kWh/t. The system of regrinding and magnetic separation is proven to be eco-efficient in iron concentrate upgrading."

Jan 1, 2014

By Teja Reddy, Narasimha Mangadoddy, Mandakini Padhi

"In mineral comminution circuits, the feed to hydrocyclone consists of a heterogeneous mixture having varied degrees of liberation and sizes leading to the multi-component particle system. The presence of multicomponent particles exhibits a significant change in the classification performance parameters. In this work, a numerical study is conducted with an artificial mixture of magnetite and silica of different proportions having similar particle size distribution to understand the multicomponent interaction in a laboratory scale hydrocyclone. The heterogeneous feed is injected tangentially would attain different settling rates under the influence of centrifugal, drag and turbulent dispersion forces. In this work, Large Eddy Simulation (LES) is used to resolve the continuous phase turbulence. Modified Algebraic Slip Mixture (ASM) model using the corrected Newtonian rheology of fines to simulate multi-density and multi-size particles of the mixture in a hydrocyclone. The influence of the multi-component particles on classification performance is extracted from the simulation in terms of the performance curve, i.e. recovery to underflow, volume fraction distribution and the key forces acting on each particle in the mixture. An interaction was observed between different components during the classification process, featuring accumulation of heavier particle at wall-side pushing the lighter particles into the inner locus of zero vertical velocity (LZVV) zone. The comparison of separation factors of different size particles presented the higher probability of the magnetite of same size reporting to wall region and hence to underflow. Hence, an increased component cut-size with the increased magnetite proportion, particularly a profound effect on lighter density component’s cut-size was observed. INTRODUCTION The multicomponent existence is found in naturally occurring ores, affecting the pure metal extraction, nonetheless also affects the comminution and classification processes. Among many another classifier, hydrocyclone is a vital equipment used vastly in many industries. The main advantages over other classifiers are a static body, low operating cost and maintenance, high throughput, low floor space requirement etc. A typical hydrocyclone consists of a cylindrical section with a central tube connected to a conical section with a discharge tube. The fluid is injected tangentially into hydrocyclone causes swirling and thus generates centrifugal force within the device. The multiphase interaction inside the hydrocyclone is extremely complex and mostly explained by theories based on hypothesis. In past years, many theoretical models were proposed like a balanced orbital model (Criner, 1950), the residence time model (Reitema, 1961) etc. Though these models give an estimation of the cut-size and other performance parameters, it cannot predict the accurate performance of the actual state of operation. Among these models, the balanced orbital theory is the most adapted concept, based on the force balances of the particle in the dual vortex flow of hydrocyclone. The finer particle is subjected to the inward drag force, generated from the outer vortex flow to the air core, and drags the particle towards the overflow. The larger particle with the higher mass have enhanced centrifugal force and falls into primary vortex near wall reporting to the underflow. Generally, the forces acting on the particle include the drag force, centrifugal force, pressure gradient force, added mass force, Saffman lift force, Magnus force and basset force (Kraipech, 2005). The major forces like a drag, centrifugal, pressure gradient are the function of the particle properties like the size and the density. Hence, the existence of the multi-size and the multi-density particle will affect the separation phenomenon, with the varied forces acting on it. The understanding of the multicomponent classification effect using ores has been only explored in few studi"

Jan 1, 2018

By Bo Feng

The development of surface charge of serpentine mineral and implications for sulphide ?otation have been studied through flotation tests, sedimentation tests, zeta potential measurements and optical microscope photos. The results show that the serpentine mineral was positively charged at an extensive pH range, with an isoelectric point (IEP) of 11.9. The magnitude and sign of the pyrite particles were pH dependent and were negative for pH values above 2. At pH value 9, where ?otation of nickel sul?de ores is routinely performed, serpentine and pyrite particles attract through an electrostatic mechanism. Slime coatings of serpentine adhere to the surface of pyrite, reducing pyrite flotation recovery. The removal of magnesium ions from the serpentine surface by acid leaching results in a decrease of serpentine IEP and eliminates the adverse effect of serpentine on pyrite flotation. Therefore, it has been clearly established that the surface charge value developed in the serpentine/aqueous electrical interface is a function of the serpentine surface incongruently dissolution. As a result of hydroxyl dissolution, the magnesium ions are left in serpentine surface, which is responsible for serpentine surface charge. The methods, which can remove magnesium ions from serpentine surface, can be used to eliminate the adverse effect of serpentine on pyrite flotation.

Sep 1, 2012

By X. Xu

This paper presents the research on comprehensive recovery of copper, gold, silver and iron from tailings from high-intensity magnetic separation in Tonglushan Mine. By comparison of experimental results of three flowsheets?regrinding of tailings-conventional sulphidizing flotation, water heating enhanced sulphidizing flotation and acid leaching-sulphidizing precipitation flotation, it is concluded that regrinding of tailings-conventional sulphidizing flotation flowsheet has the best economical and technical performance and practicability. Regrinding and using the mixture of sodium hydroxamate and sodium xanthate are two of the notable technical characteristics of this best flowsheet. The system for comprehensive recovery of tailings has been put into production. It not only can recover the valuable minerals from tailings in Tonglushan Mine, but also can reduce the environmental pollution, resulting great economic and social benefit.

Jan 1, 2014

By Linghu Changjin

Based on the characteristics of typical marine sedimentary phosphate rock in Guizhou, Southwest China, together with the research findings made on the surface electric properties of pure collophanites taken from different areas in pure water and under the action of collectors, a pure minerals flotation test of collophanite was conducted in this research. The differences of collophanite flotation behavior and the effects of the different pH values, varieties, and dosage of collector on flotation separation of collophanite were studied. It is suggested that that in pure water, collophanite had a negative charge within a wide pH range. The electro negativity values of collophanite increased with the addition of collectors GJBW and WF-01. When GJBW and WF-01 were used as collectors, the collophanite was depressed in acid medium, but had a good flotability in basic medium.

Sep 1, 2012

By J. Jirestig

Poor grade iron ore, suffering from interlocked particles, is challenging for any process technology. Extensive grinding is required to attain liberation and to yield concentrates of desired grade. Fine particles are commonly very difficult to retrieve, resulting in value losses to tailings. In this paper, results from HGMS tests on fine to ultra fine hematite are reported. Special emphasis is put on slurry flow velocity. If hydrodynamic drag force, i.e. flow velocity is not controlled and kept constant during the feed and/or rinse phase, fine particles will not be captured and retained. Flow velocity control and constant flow during separation are achieved by discharge valves/slots and parallel magnetic flux and pulp flow configuration. In tests, increased slurry velocity from 178 to 268mm/s caused Fe-recovery to drop from 78 to 48%. Proving that flow velocity control is essential to optimise grade and recovery. HGMS tests at the Metso mineral laboratory on natural (weathered) hematite fines clearly show a large potential to recover valuables, currently lost to tailings. Even at particle size distributions as low as D80=35µm concentrate grades and recovery are very satisfying. Two samples, in-plant desliming rejects (D80=35µm and 50µm) where significantly upgraded and recovered, from 45,3% to 63,6% and 53,0% to 63,4% Fe, at 73,8% and 81,1% Fe-recovery respectively. Other types of in plant rejects, such as gravity separation or WHIMS tailings, also benefits from HGMS separation. Gravity separation reject, 55,8% Fe, at D80=500µm was tested, yielding a magnetic concentrate of 60,8% Fe at 50,7% Fe-recovery. The results indicated that the hematite was poorly liberated. HGMS separation was repeated after a regrind to D80 150µm, resulting in a magnetic concentrate of 62,8% Fe at 75,9% Fe-recovery. The tests prove that hematite, presently lost to tailings streams, can be recovered by HGMS and thereby significantly contribute to improved overall economy. Keywords: HGMS, magnetic separation, recovery of ultra-fine hematite, Indian hematite ores, hematite recovery from tailings

Sep 1, 2012

By D. Chen

The experiment adopted magnetic separation-priority flotation (first to float copper,then float lead) combined technology to deal with a complex Cu,Pb ,Zn multi-metals ore which has high sulphur content, difficult to separate Cu, Pb ,Zn minerals from sulphur and separate Cu from Pb. Floatable pyrrhotite was separated through magnetic separation which could eliminate the adverse effect on the flotation followed up. And then adopting the priority flotation process to recover the Cu, Pb ,Zn from the magnetic tailings. In priority, flotation Cu, BP(a kind of ethionine ester collector ) and ethyl xanthogenate were used as the collector, LD-1 and sodium sulphite were used as the depressant.The depressants combined with humic acid sodium and lime were used for chalcopyrite ? pyrite separation to further improve the copper concentrate grade. Considering the raw ore that contain 0.32% copper, 0.54% lead and 25.54% sulfur. The copper concentrate grade is 23.61%. The lead content of copper concentrate is only 0.85% . The recovery of copper is 75.03%,and the lead concentrate grade is 54.58%, the copper content of lead concentrate is only 0.81% and the recovery of lead concentrate is 62.24%. The mineral processing indexes were excellent, finally realizing the high effective separation of Cu, Pb , Zn and pyrite. This technique provides a new approach to highly utilize complex copper-lead-zinc ore.

Sep 1, 2012

By R. S. C. Smart

Surface chemical factors, including the balance of hydrophobic (e.g. collectors) and hydrophilic (e.g. oxidation products, precipitates) species, are major control determinants in flotation rates of specific minerals and therefore grade and recovery. There are a number of challenges involved with the surface analysis of different mineral phases from process streams in a flotation facility. The first is to collect samples that are representative of the process and retain their surface chemistry prior to introduction into the instrument. The second challenge in studying the surface chemistry of specific minerals is to find reliable methods of mineral phase recognition. In surface analysis of mineral particles, confident mineral selection can be difficult with many multi-metal minerals and with precipitated, adsorbed, reacted and contaminant species in the outermost molecular layers. The third challenge is to provide a statistical surface analysis of multiple grains of the same mineral. Methods to achieve these aims are described. Principal component analysis (PCA) of ToF-SIMS data provides improvement in phase recognition, particle selection and associated variations in surface species. Specific examples from both lab and plant operations, demonstrate that this technique can be utilized to differentiate surface chemical factors promoting (hydrophobic species) or inhibiting (hydrophilic species) flotation. A study of copper ion transfer (inadvertent activation) from chalcopyrite to pyrite and sphalerite clearly identified a statistical difference in copper intensities between the sphalerite and pyrite phases corresponding to their flotation response. The PCA analysis applied to concentrate and tails samples collected from the Inco Matte Concentrator demonstrated extensive CuOH and NiOH transfer between chalcocite and heazlewoodite minerals. The statistical analysis has been able to identify mechanisms controlling recovery and selectivity. High intensity conditioning (HIC) tests in which sphalerite was separated from a complex sulfide ore gave a 5% increase in the overall Zn recovery. The PCA/ToF-SIMS statistical analysis revealed the discriminating depressant action of adherent aluminosilicate (gangue) fine particles and adsorbed ions on the surface of sphalerite grains. HIC conditioning resulted in the removal of these gangue fines improving surface collector attachment efficiency.

Jan 1, 2014

By L. S. Bbosa

Single particle impact breakage experiments provide essential data to aid in understanding of rock fracture in comminution. Such experiments, conducted using devices such as the drop weight tester, split Hopkinson bars and more recently the rotary breakage tester, have been successfully used to characterize ore breakage properties in relation to measured fracture energies. The work presented in this paper highlights the techniques behind the calculation of impact breakage properties from each of these three devices. The breakage parameters that can be calculated from experimental data from each of these are to be described. Drop weight tests are used to calculate A and b hardness parameters using the standard JK breakage model. Split Hopkinson pressure bars are used to establish the ultimate compressive stress of particles through single impact breakage tests and the fraction of impact energy utilized to cause particle fracture. Low energy breakage tests using the rotary breakage tester are shown to be used in calculating particle breakage probability. Methods to calculate parameters related to particle breakage probabilities such as E0 and Ecrit are also discussed.

Jan 1, 2014

By V. I. Ryaboy, I. V. Ryaboy, E. D. Shepeta

"The problem of separation of copper minerals and arsenopyrite remains relevant because of environmental requirements. The selective action of reagents with the thioamide group (thioamides) is known in iron sulfide’s flotation of pyrite and pyrrhotite. The aim of this study was to reduce the arsenic content in the copper concentrate when using thioamides by reducing the flotation of arsenopyrite in the flotation of the sulfide part of the skarn scheelite-sulfide ores. We have chosen the most widely used thioamides for the study, such as Z-200. We also synthesized new reagents with the thioamide group. The most selective and the most powerful thioamide copper collector were used for further studies. Reduction of arsenic content in copper concentrates is achieved in the following way: You need to apply a strong thioamide collector with a selective but weak dialkyldithiophosphate collector, or vice-versa, a selective, but a weak thioamide collector should be used with the dialkyldithiophosphate reagent with strong collective properties. The proposed combination presents industrial interest because of its accessibility. The application of thioamides in copper minerals and arsenopyrite selection has showed that these reagents have fewer selective properties than dialkyldithiophosphates. To achieve the comparable recovery of copper using dialkyldithiophosphates requires markedly greater consumption of thioamides, due to their lower hydrophobic ability. The application of a composition of thioamides and dialkyldithiophosphates allows to increase the recovery of copper and to obtain a lower arsenic content in copper concentrates compared to their individual use. The lowest arsenic content in the copper concentrate is obtained in the composition consisting of the newly synthesized thioamide with strong collective properties and selective dialkyldithiophosphate. The addition of even small amounts of xanthate to the composition of thioamides and dialkyldithiophosphates causes a sharp increase in the arsenic content in the copper concentrate without a notable increase in copper recovery."

Jan 1, 2018

By Longjiang Li, Mao Jiang, Zhihui Shen, Guizhou University, Yin Pan

This paper aims to study the influence and action mechanism of collector Y-89 on the flotation of auriferous pyrite. The measurement to identify adsorption quantity, IR and XPS spectrum analysis and flotation experiment made on the pure mineral were conducted. The research results show that when the dosage of MIBC is 20 mg/L, and pH of 8, the dosage of Y-89 over 60 mg/L, the pyrite recovery rate is greater than 80%.And when the dosage of Y-89is 60 mg/L, dosage of MIBC 20 mg/L, the pH in a wider range (pH=4~9), the recovery is greater than 75%. When the pH is above 10, the pyrite is depressed and its recovery rate is found to be dramatically dropping. Adsorption quantity measurement also shows that the strong alkaline conditions inhibit the adsorption of Y-89 on the surface of auriferous pyrite. IR measurement indicates that chemisorption of Y-89 occurs on the surface of auriferous pyrite. XPS spectrum analysis indicates that without adding Y-89, oxidation reaction occurs on the surface of pyrite. But when Y-89 is added, the chemical environment of Fe on the surface of pyrite has changed. Such findings indicate that with Y-89, chemisorption occurs on the surface of auriferous pyrite.

Jan 1, 2014

By M. Roy

Coke combustion during sintering process is significantly governed by coke breeze size distribution, which in turn affect sinter quality i.e. sinter granulometry, Tumbler index, Reduction Degradation Index and Reducibility Index of sinter. To know the effect of microfines of coke breeze on sintering process parameters, pot sintering tests were conducted and it was found that when microfines are eliminated and optimum coke size (1-3mm) is used yield of sinter increased by more than 7%. Similarly productivity increased by 9%, the strength of sinter i.e. ISO Tumbler Index increased by 2.3% and +10mm sinter size increased by 5.5%. Controlling of microfines during crushing and by improving crushing index will result in improved quality and productivity of sinter with lesser amount of coke breeze. This paper describes that how to optimize solid fuel i.e. coke breeze consumption in sintering process through granulometry control. Keywords: iron ore sintering, coke breeze granulometry, productivity of sinter, quality of sinter

Sep 1, 2012

By F. Boylu

In this study, Ca-bentonite was subjected to a series of systematic hydrocyclone tests with the aim of developing separation procedures and in turn achieving optimum recoveries. In hydrocyclone tests, vortex and apex diameters and also feed pressures were investigated. In each hydrocyclone set, vortex diameter was kept constant while the other two parameters varied to produce bentonites con-centrates of various smectite contents. The separation efficiencies were evaluated based on the cation exchange capacity (CEC), particle size and swelling index. The detailed hydrocyclone tests showed that, upgrading of Ca-bentonites require procedures different from the bentonites reported in the literature. Sodium and mixed bentonites are easy- to-disperse and easy-to-separate whereas calcium types need to be scrubbed rigorously for disintegration. Scrubbing properties of ca-bentonite were investigated as a function of scrubbing time and percent solids by weight (PS). The scrubbing conditions at 700 rpm for 1.5 hours and percent solids of 30 % were found more effective for achieving a better quality bentonite. In addition to the parameters mentioned above, the effect of percent solids on hydrocyclone separation was also studied. Although Ca-bentonites permit studying at higher percent solids, increasing solids content of the pulp deteriorated the quality of the clean products. Application of an appropriate separation scheme enabled the development of a unique separation procedure involving stage wise scrubbing followed by hydrocycloning which yielded calcium bentonite concentrates with CEC of 90 meq/100 g and high swelling indexes of 12 mL from the original bentonite of 65 meq/100 g and 7.0 mL, respectively. These results indicate that upgraded bentonite products can be conveniently used in various diverse industrial applications including bleaching earth, desiccant, cat litter, paper etc.

Jan 1, 2014

By I. Grigoryeva, G. Voiloshnikov, V. Dementyev, N. Moskaeva, N. Voiloshnikova

"Adsorption processes with use of anion exchange resins are widely applied in the gold mining industry of Russia and the former Soviet Union. Anion exchange resin AM-2B and its analogs (with mixed basicity) are used as adsorbents. This paper focuses on the study of weak base anion exchange resin and its comparison with AM-2B resin. Different nature of the ion exchange groups of the adsorbents mentioned above provides essential differences in their properties both during adsorption and elution of gold and silver. Multistage gold elution and resin regeneration procedure is used for AM-2B resin whereas alkaline cyanide solution is used for weak base resin and allows for the reduction Capex and Opex in comparison with AM-2B resin. Anion exchange resins AM-2B and PuroGold S-992 were tested. Weak base resin is sensitive to pH of adsorption medium. Optimal pH value is 10.1-10.3 (at ?? >10.5 gold loading onto resin decreases dramatically). Adsorption isotherms for gold, silver, nonferrous metals, cyanide and thiocyanate ions from synthetic individual metal cyanide solutions were defined. Adsorption of all components onto PuroGold resin was lower than for ??-2? resin. Adsorption of metals from the solution with equal molar metal concentration (0.1 mg-equivalent/L of each metal) was also studied. The affinity of resins to cyanide metals complexes was established. Weak base resin has higher selectivity to gold in comparison with ??-2B resin and is less sensitive to ion composition of cyanide solution or pulp treated. Weak base resin was tested for gold recovery from gold ores. On the base of test results it was recommended to introduce this resin at some new plants in Russia. Commissioning and operation performance of gold plants confirmed efficiency of weak base resin use."

Jan 1, 2014

By J. Masinja

The mining industry is known to be a potential major contributor to the industrial development of any economy. Large-scale mining has been going on in Zambia for the last 100 years. The impact of mining in Zambia has been to create a development corridor along the line of rail to the Copperbelt Province, where hitherto, mining was concentrated, and then to develop a large consolidated high-density economic zone covering an area of about 72 km by 60km. This area is home to a number of very large integrated copper/cobalt mining complexes. The mining zone has expanded to the Northwestern Province in the last 10 years, where the largest copper mine in Africa now exists, having produced about 300 000 tonnes of copper in 2011. The total output of the Zambian mining industry is now about 820 000 tonnes per annum with projections of reaching 1.5 million by 2015, due to new Greenfield investments expected to come online by then. These new mining industry developments have come on the back of strong and sustained high base metal prices, in the last 10 years or so, due to demand mainly from China and India. This new lease of life has increased the contribution of the sector to the national treasury. The mining industry in Zambia has undergone a very important ownership restructuring with the sale of the previously Government owned parastatal, Zambia Consolidated Copper Mines (ZCCM) which dominated the sector, to allow for private sector participation. The privatization process lasted from about 1995 to about 2002. The recent growth of the mining sector has unfortunately not been matched by an adequate supply of skilled manpower for various reasons. These include: (i) A lack of strong in-house training strategies by the new mine owners (ii) Decrease in industry support to the training institutions (iii) The demise of and restructuring of ZCCM which has consequently limited the Government human resources planning tools for the mining sector (iv) The cyclic nature for the fortunes of the sector has lead to fluctuating interest of student recruitment into training institutions (v) Limitations, both staff and equipment, in the training institutions (vi) A re-structuring of the training institutions This paper examines the current status, and student output from tertiary training institutions for the mining sector in Zambia. This is then compared to the skilled labour demands of the sector. The various cause and effect issues are considered and a proposal on how this skills gap could be addressed sustainably is proposed. Keywords: skills gap, graduate training, quality of graduates

Sep 1, 2012