Search Documents

By Olgac Kangal, Ali Guney, Gulay Bulut, Guven Onal, Ayhan A. Sirkeci

"This paper presents the results of pilot scale column flotation applications in the two different copper concentrators in Turkey. The Kure Copper Plant is located in the Black Sea Region of Turkey. There are four types of copper ore formations in the Küre region. The so called disseminated ore contains 60-70% siliceous minerals of which Cu content is around 0.5%. The remaining three ore types in the region are generally named “massive ores”. The massive ores may assay up to 15% Cu and the major gangue mineral is pyrite associated with relatively little amount of silica. The main copper mineral in all formations is chalcopyrite that is generally finely disseminated in pyrite therefore satisfactory liberation requires ultrafine grinding especially in the case of the massive ores.A blend of these ores, containing 1.7% Cu on average, is fed to the Küre Copper Concentrator whose capacity is 1.2 million tons of ore annually. Unfortunately, today the plant operates below its designed capacity treating around 550,000 tons of ore per year. The design of Küre Copper Plant was undertaken by the Outokumpu Company of Finland. The operation of the plant is almost automatically controlled and the feed, the concentrate and the tailings are assayed for copper by on-line XRF analysers. The particle size analysers are also connected to the grinding circuit. The feed material is ground almost below 50 µm and the flotation is conducted around pH 11.2 using Hostaflot X-231 (a trade mark of Hoechst) as the collector. Apart from the rougher cells, there are four cleaning stages after which the final concentrate is produced. A very fine grinding requirement for an adequate level of liberation makes successful flotation difficult and consequently the final concentrate can hardly assay above 16% Cu leading to copper losses around 20% in the tailings that contains 0.3% copper."

Jan 1, 2003

By R. Peter King, Claudio L. Schneider, Reiner Neumann

Predicting the liberation spectra that is produced from breakage of two-phase ores under the random fracture assumption can be accomplished by measuring the conditional, on length, linear grade distribution directly from images obtained from a representative sample of the unbroken texture. The technique tremendously simplifies the prediction problem by avoiding the multiple convolutions that arise from the traditional method based on a description of texture from a measurement of the chord length distributions associated with each phase in the unbroken texture. For a 3-phase system, the phase transition probabilities associated with the textural information make the traditional calculation an almost insurmountable mathematical problem. The direct measurement procedure on the other hand can be expanded to three phases comparatively easily.

Jan 1, 2003

By Bertil I. Pålsson, Sture V. Persson, Kent T. Tano

"Autogenous (AG) and semi-autogenous (SAG) mills often operate in an unstable state because of the difficulty to balance the rate of replenishment of large ore particles from the feed with the consumption in the charge. This has led to an increased interest in obtaining an accurate and direct measurement of mill load and the behaviour of the mill charge. A problem in attempting to measure those parameters is getting a sensor that is both robust and sensitive enough for continuous on-line measurement.Techniques that measure the force acting on the lifter when it hits the charge inside the mill have got an increased interest recently because of the ability to combine it with DEM modeling. This paper presents a method for the measurement of the apparent filling level in a pilot ball mill equipped with the Metso Continuous Charge Measurement system (CCM). In this technique a strain gauge sensor is mounted on a flat steel spring which is fitted into a recess underneath a lifter bar. In addition, a conductivity probe, the Boliden Grinding Measurement System (GMS), is mounted in another lifter bar with the purpose of comparing the two measurements. To visualise the behaviour of the charge a 2D DEM modelling technique is used with Metso HFS software.The pilot mill is a grate-discharge mill, equipped with 12 rubber lifters of square size 0.1 m, face angle 45 degrees. Steel balls in the size range 10-30 mm and density 8000 kg/m3, are used in the experiments. Test material is a hematite pellet feed, d50 around 45um, chosen to get stable grinding conditions with respect to feed size variations.The experiment is meant as a first test of the equipment’s performance, and to study how the sensors respond to changes in some operating variables. To get an understanding of, and distinguish between correlation and causality, experiments are performed according to a full factorial design with two levels, and in addition two replicates of the experiments at a center-point in the charge level setting."

Jan 1, 2003

By Markus A. Reuter, Antoinette van Schaik

"INTRODUCTIONGoods and products, such as passenger vehicles, are manufactured by using a wide spectrum of different raw materials to meet highest consumer requirements during use. Due to the time-varying composition and complexity of multi-component products such as cars, recycling is complicated. It involves a network of interconnected processes and material and energy flows. Improving the efficiency of the material cycle of the car to comply with the recycling targets as imposed by EU legislation, requires insight into all aspects influencing the closing of the material cycle (dynamics, technology, economy, legislation, etc.) and their mutual relation. In order to define the link between recycling end-of-life products, their changing composition and design a dynamic model was developed for the resource cycle of cars. The model integrates the optimisation of the material cycle with the dynamic behaviour of recycling systems."

Jan 1, 2003

By Javier Baladron, Mijail Villar, Brandt Henriksson

"In this presentation an overview will be given of what has been observed by the authors in the copper concentration industry, with a large diversity of tailing thickeners operating under different conditions, although many of them are located in the same neighborhood. A closer look will be taken at the reported performance from different sites and from different thickener designs, either conventional or high rate, including those that were retrofitted, regardless of the thickener brand. An analysis is also made of the generic correlation of the size of the thickener and the performance in terms of solids loading (or unit area) and % solids. The paper envisions a technology development route, makes a brief analysis of the economic impact of the suggested route and points out the need for development in technologies around tailings thickeners, such as automation, yield stress measurement, slurry pumping and construction methods."

Jan 1, 2014

By Raquel Franco de Souza Lima, Isao Matsuoka

"Microflotation studies and abstraction experiments were conducted with synthetic oxide spinels relating to chromite (MgCr2O4, FeCr2O4, FeFe2O4 and FeAl2O4), using sodium oleate as collector. An attempt was done to correlate this data with the speciation of oleate in the bulk solution and at the interface solid-water, to explain the floatability curves. The microflotation tests were conducted using a microflotation cell. The abstraction of sodium oleate was measured at 25°C, with one gram of synthetic spinel and the abstraction time was 30 minutes. After centrifuging, the residual oleate concentration in the supernatant was measured by using the spectrophotometric method described by Mizuniwa et al. (1977), that covers the range from 1.5 to 9 ppm. To cover the range from 0.2 to 1.5 ppm, the residual oleate concentration was measured using the spectrophotometric method described by Gregory (1966). The amount of oleate abstracted was calculated from the difference between initial and residual (equilibrium) concentrations.Figure 1 shows the floatability of FeCr2O4, FeAl2O4, FeFe2O4, MgCr2O4 as a function of pH and sodium oleate concentration of 1 x 10-5 M. The IEP of each sample is indicated in the figure by a vertical line in the horizontal axis. The chromium-bearing spinels FeCr2O4 and MgCr2O4 show the lowest isoelectric points (IEP), around pH 6, while in the case of FeFe2O4 and FeAl2O4, the isoelectric points lie at pH 6.5 and 7.3, respectively. It is seen that the flotation-pH curve for FeFe2O4 has a peak at the pH of the IEP, while flotation peak for FeCr2O4 appears at pH below the IEP and that of MgCr2O4 does at pH above the PZC. On the other hand, FeAl2O4 is floated at pH range between about 4 and 7,3 (IEP). This suggests that the pH value at which the maximum flotation occurs is dependent on the sort of spinel to be floated, though it appears in the vicinity of the respective IEP."

Jan 1, 2003

By Graeme Heyes, Warren J. Bruckard, Michael A. Somerville

"Over the past few years CSIRO Minerals has been conducting research aimed at developing a continuous copper converting process to replace the traditional two-stage batch process that is currently used to produce blister copper. Sirosmelt type reactors and calcium-ferrite (lime-based) slags have been used rather than the conventional iron silicate slags. The research work has now been extended to focus on the development of a single-stage continuous copper making process (so-called direct copper converting) in which copper concentrates are converted to low-sulfur blister copper in a single step, that is the smelting and converting steps occur in one continuous stage.One feature of the direct copper converting process is that copper losses to the slag phase can be high, meaning the slag produced needs to be treated to recover the copper value. The feasibility of the whole copper making process will most likely depend on the efficiency and cost effectiveness of the copper recovery stage. Flotation has been identified as the most economical option to recover the copper from direct copper converting slags where it has been estimated that a copper recovery from the slag of above 90% is required to make the overall single stage copper making process economically feasible.A limited series of laboratory batch flotation tests was conducted on a suite of calcium-ferrite-based slags made in laboratory smelting trials. Copper sulfide concentrates from MIM were used as feed-stocks. The objectives of this work were to develop a robust flotation process to maximise the copper recovery and iron rejection from slags made in the process, and to establish operating conditions for future continuous flotation pilot plant trials.The slags treated included a reduced low copper slag, an oxidised high copper slag composite, and a very reduced low copper self-pulverising slag. The copper content of the slags varied from 2.9% to 14% Cu and the CaO/Fe ratio varied between 0.30 and 0.54. In general, the higher the copper content the more oxidised the slag. The copper was present as metallic copper, oxide copper and copper-calcium ferrite phases with the phase mix related to smelting conditions. The slags were crushed, ground, wet-screened at 355 or 210 µm to remove coarse metallic particles of copper, and floated at natural pH (about pH 11) using reagents and conditions appropriate for the selective recovery of the copper phases. Reagent additions were typically 200 g/t KEX and 500 g/t Na2S.9H2O and the grind size was generally a P80 of about 40 µm."

Jan 1, 2003

By D. P. Hatfield, G. de Jager

"Recent developments in image analysis techniques and the power of computer hardware have spurred international interest in the potential uses of image analysis techniques in a range of industrial applications. One of these applications is the control of the complex flotation process. Despite years of work, the flotation process is still poorly understood. Current attempts to control flotation cells focus on consistently duplicating the control achieved by human operators.In human control of flotation two of the dominant visual cues are the froth flow speed and the froth stability. These two factors can be measured and inferred respectively from image analysis of video of the froth surface. Two important hydrodynamic variables for control of the flotation process are the air addition rate and the level of the froth pulp interface.The current work focuses on the relationship between froth flow speed and the rate of recovery of concentrate from a flotation cell. Results are presented that show a strong relationship between flow speed and concentrate yield. These results include tests where the conditions in the cell were not changed, as well as tests involving changes to the cell level and air addition rate. Preliminary results are presented which show a correlation between froth stability and froth percent solids.Future developments of the system will include comprehensive froth texture typing, colour space and stability analyses."

Jan 1, 2003

By Francisco Vicuña, Miguel Becerra, Gonzalo Montes-Atenas

"The optimization of the copper recovery from smelting slag by a process of comminution / flotation has been a widely discussed topic during the last few decades. Several studies covering the characterization of different types of slag, the impact of the slag cooling rate and of different flotation operating conditions on the flotation performance have been widely published. Currently, at El Soldado mine site (Angloamerican), there are large copper bearing slag deposits that can be a profitable alternative for the concentrator with capacity to treat this material. Under this process schema, the optimization of the flotation process to obtain better copper recoveries is a relevant topic of study. The aim of this study is to assess the efficiency of a sulfidation stage of a slag and to correlate that process with copper recoveries results in a flotation circuit. This article presents a detailed examination at both laboratory and plant scales of the slag sulfidation on the recovery of copper in the flotation process. The experimental methodology involves studying the effect of the sulfidation agent dosage, the pH, the particle size distribution of the flotation feed and the conditioning time. Furthermore, the performance of the sulfidation stage was analysed through the XPS analytical technique. It was observed that the sulfidation of particles in floatable size fractions correlated well with the increase in copper recovery. The results indicated that it is possible to increase between 2 to 4 points the total copper recovery with a sulfidation process implemented appropriately."

Jan 1, 2014

By N. Ahmed

"This paper is concerned with the drainage behaviour of gangue mineral in the froth phase. Experiments were carried out in a continuous laboratory flotation cell in which froth depth and bubble size can be changed independently. The fraction of solids returning from the froth to the pulp zone was expressed using a rate constant by considering the appropriate froth regimes. A mixture of hydrophilic solids (silica) and floatable particles (glass ballotini) was used as a flotation feed. Samples of glass ballotini of different hydrophobicities were obtained, using controlled silanation. Three samples, with contact angles of 50, 66, 82 degrees, were used. The effect of the initial bubble size (pulp bubble size), concentration of gangue mineral in the froth zone, and froth depth on the drainage of silica, were also investigated.Typical results obtained from this study is shown in the figure given below. In this figure drainage rate constant for the entrained solids in the presence of particles of the three hydrophobicities is plotted against froth height. As observed, the drainage rate of the entrained solids increases considerably with an increase in the degree of hydrophobicity. Concerning the effect of pulp bubble size on the drainage rate of entrained solids, larger bubbles always give higher drainage rates due to formation of relatively loose froth structures which allows gangue particles to easily move down to the pulp zone. Conversely, smaller bubbles exhibit lower drainage rate constants, in particular at shallow froth depths."

Jan 1, 2003

By Daniela Campos, Aldo Casali, Gonzalo Montes-Atenas

The understanding of the effect of the major variables influencing the froth flotation performance may allow both to predict and to identify best operating conditions towards optimizing the process efficiency. The aim of this research work is to model the effect of dissolved oxygen onto froth flotation performance. Experimental pilot plant results were obtained from a continuous circuit consisting of a ball mill and a rougher bank of four flotation cells. A series of flotation experiments were run with different conditions of dissolved oxygen keeping constant most of other operating conditions. Variables difficult to control were measured or estimated. A set of mathematical models suggested in the published literature were tested. It was found that the copper recovery results were highly sensitive to the concentration of dissolved oxygen. The latter confirmed the reactions mechanisms associated to the collecting capabilities of current flotation reagents used in the flotation of copper sulfide ores. On the contrary, the results of molybdenum recovery varied non-linearly with changes in dissolved oxygen which could not be explained directly in terms of the computed specific rate constants. The error analysis confirmed that Klimpel continuous model exhibited the best specific rate constant correlation with molybdenum recovery data. Lastly, the classic particle force balance equations indicated that the adjustments of estimated mineral liberation with experimental data exhibited a turning point when passing from highly liberated to low liberated particles. The values of recovery for such turning point correlated well with the concentration of dissolved oxygen. The results indicated corrections due to changes in the dissolved oxygen must be incorporated in future froth flotation descriptions.

Jan 1, 2014

By Barbara Peszko, Tadeusz Tumidajski

"Various methods are used to identify the grain composition of fine-grained materials because so far the best notion of the grain size has not found and there is no single method to define grain size. In practice the most important are the following grain sizes: sieve diameter dt, effective diameter de, substitute diameter d2 and statistical diameter dst. The mentioned sizes are connected with the methods of analyses. Methods are correct but measure of different diameters of grain and their results are different.The most important methods of granulometric composition analyses are the following: the sieve analysis, the sedimentation method and the conductometric (Coulter-Counter) methods. In each of these methods various physical features connected with the grain size are measured.Sizes of grains defined by different formulas or measurement methods are associated mutually by dependencies, which are results of differences in their determination or calculation ways.In order to determine principles of results comparison the classification analysis results on linearly or non-linearly connected was made. Analyses which results demonstrate the same type of grain size distribution are treated as linearly connected. It is based on the general formulae which determines the probability density function of random variable which is the function of another random variable having the known density function.In order to show the difference in the grain composition of the same material qualified by different methods, three methods of investigations were distinguished. They are: the sieve analysis performed on precise sieves, the sedimentation analysis performed by means of a sedimentation balance “Sartorius” and the microscopic analysis performed after preparing a microscopic slide where the grain size was measured by the Martin’s method.The materials selected for the analysis were quartzite and glass, which are the material of high purity.The obtained results of mentioned above three types of analyses were approximated by distribution function of four distributions: Weibull, log-normal, cut Weibull and Gaudin-Schuhman."

Jan 1, 2003

By Andrew D. McCallum, Russell A. Heins

"Until the advent of intensive cyanidation, gold gravity concentrates were generally treated by tabling. The table concentrates were smelted while table middlings and tailings were recycled to the milling circuit for further grinding and subsequent leaching in the CIP/CIL circuit. Gold recovery on production tables is relatively low, often only 30 percent, and rarely above 60 percent. Significant factors in tabling performance are; mineralogy and the operator’s experience and ability. Units have been developed by Gekko Systems to treat both batch and continuous gold concentrates. Unit sizes are determined by leach kinetics and the required residence time of the concentrate in the unit.Gekko commenced the commercialisation of intensive leaching of gravity gold concentrates in 1997 with the first commercial prototype of the InLine Leach Reactor (ILR). Over 20 units are now installed worldwide with half that number on the African continent. South African mines, South Deeps (Placer Dome WAJV) and Target (AvGold) have both installed InLine Leach Reactors. Ashanti Goldfields have placed the ILR on their standard equipment list and have six operating units with a seventh on order. AngloGold installed one of the first ILR production units at Morila in Mali.Gekko Systems successfully installed an ILR1000 Batch unit at the Antapite Mine in Peru in December 2002. The unit was installed to treat gravity concentrates and to replace a shaking table. Following installation, gravity gold recovery increased from 15% to 40% of total gold. The unit was operational from start up and the first gravity batch treated achieved 98% gold recovery. The gravity concentrates also have a high silver content and 95% recoveries on silver were also achieved.Preliminary testwork identified that the concentrates required additional oxygen to achieve peak performance. As a result of optimisation work in the laboratory, leach kinetics in the ILR have been excellent with only 6 hours residence required to achieve maximum gold extraction."

Jan 1, 2003

By Georgios N. Anastassakis

"The depletion of the high-grade chromite ores and the inefficiency of the gravimetric methods to process fine particles has shifted the industrial and research interest from gravimetric separation methods to flotation. However, the response of the minerals to various flotation schemes is not clearly established. In this work, the physicochemical behavior of chromite and olivine is studied using a fatty acid collector.The minerals used were from Vourino area (Kozani, Northern Greece). Macroscopically pure samples of chromite and olivine were selected by hand picking, crushed and subsequently ground to the required size. Each sample was then submitted to panning and magnetic separation for the removal of impurities. The mineralogical and chemical analysis of the purified samples revealed the following: a) The purity of chromite was 95% while the minor constituent was mainly magnetite. Its chemical analysis was: 12.50% Fetot, 2.50% SiO2, 54,54% Cr2O3, 9.31% Al2O3, 0.47% CaO, 13.10% MgO. These analyses show that Cr3+ has been substituted by Fe3+ and Al3+ as well as Fe2+ has been significantly substituted by Mg2+. b) Forsterite is the main constituent of olivine either as pure forsterite (Mg2SiO4), which is the prevailing form, or as iron-forsterite [(Mg,Fe)2SiO4] in less amount. Chrysotile, which belongs to the serpentine group, was also detected at a percentage of 10-15%. The chemical analysis of olivine was: 36.90% SiO2, 0,53% Cr2O3, 7,43% Fe2O3, 0.72% Al2O3, 0.91% CaO, 47.00% MgO, 6.02% LOI.The electrokinetic behavior of the minerals was studied in a electrophoretic mass transport equipment Model 1202 of Micromeritics. The reagents used were sodium hexa-metaphosphate of commercial grade and sodium oleate."

Jan 1, 2003

By Alim Gül, Güven Önal

"Recently, there have been some attemps on the treatment of low grade ores and old plant tailings due to the decrease in high grade ores and the increase in the metal consumption with increasing world population. Cost of mining and beneficiation of low grade ores become prohibitive since the costs of grinding before flotation make the process unfeasable. Therefore, preconcentration of these ores prior to flotation becomes more important. The concentration of ores preconcentrated in coarse sizes provides a decrease in investment costs as well as grinding and flotation costs. Additionally, the requirements of less space for tailing disposal and less reagent consumption are also important from the viewpoint of environmental considerations.In this study, ore sample containing 0.6 % Cu and taken from Küre-Asiköy ore body was used. Ores contained chalcopyrite and pyrite as main minerals and diabaz, quartz, chlorite and sericite as gang minerals.Samples were all crushed under 9 mm by considering the preliminary studies and float and sink experiments were carried out with the sample in the size range of –9+1 mm using different densities of heavy liquids. As a result of these tests, it was shown that 60 % of the material should be discarded as tailings with 0.1 % Cu content. By considering float and sink test results, the following experiments were performed by using heavy medium cyclone and jigs.As a result of heavy medium cyclone tests, which are conducted on the sample in size range of –9+1 mm, 57 % of the feed material was discarded as tailing with 0.08 % Cu content and 7 % Cu loss, while a concentrate containing 1.43 % Cu was produced with 93 % efficiency (Table 1). Jig tests were done with the samples in the size range. As a result of jig tests with –9+1 mm size group sample, approximately 46 % of feed material was discarded as tailings with 0.13 % Cu content and 10.6 % Cu loss, while a concentrate with 0.94 % Cu content was obtained (Table 2)."

Jan 1, 2003

By Jean-Paul Franzidis, Robert G. Coleman, Emmy V. Manlapig

"The Floatability Characterisation Test Rig (FCTR) is a self-contained, highly instrumented mobile pilot flotation plant developed by the Julius Kruttschnitt Mineral Research Centre, the Mineral Processing Research Unit of the University of Cape Town and EIMCO, as part of the Australian Minerals Industries Research Association (AMIRA) P9 Project. Apart from being a fully operational pilot plant, the FCTR was designed to determine flotation model parameters and to develop and validate flotation plant modelling, scale-up and simulation methodologies.The FCTR was installed at WMC’s Kambalda Nickel Operation where circuit modelling, simulation and scale-up test work was performed using the AMIRA P9 flotation model as the basis of the analysis. The model parameters were obtained through metallurgical sampling, batch flotation tests and gas dispersion characterisation around the FCTR. Model parameters were determined for four FCTR circuits, each of increasing complexity. The circuits ranged from a simple rougher-cleaner configuration with no recycle streams, to a more complex rougher-cleaner-recleaner configuration with two recycle streams.Using the P9 modelling methodology, the system was analysed using four mineral species: nickel sulphide, iron sulphide, copper sulphide and non-sulphide gangue. The floatability of each mineral was analysed as two floating species (fast and slow) and a non-floating species. Mass balanced data from all four FCTR circuits were regressed simultaneously together with data from 47 batch flotation tests. Nonlinear regression was used to determine the solution. The model fit was found to be accurate with most data points predicted within experimental standard deviations. A Monte Carlo sensitivity analysis was also performed to establish the stability of the regressed parameters.Using the P9 simulation methodology, simulations of five FCTR circuits (different from the previous four) were performed. The FCTR was also operated in these five circuit configurations to obtain experimental data to validate the simulated predictions. The simulations were found to predict the recovery and grade of nickel sulphide and copper sulphide within experimental standard deviations. The prediction of recovery and grade of iron sulphide and non-sulphide gangue was less accurate. Overall the FCTR simulations predicted the changes in circuit configuration well."

Jan 1, 2003

By Buks Kruger

"After the milling and flotation of the platinum bearing ore, the flotation concentrate is electrically smelted in 6-in-line electric arc furnaces and the resulting furnace matte treated in Peirce Smith converters to remove the iron sulphide. The iron free (less than 1% Fe) converter matte is then granulated and sent to the Base Metals- and Precious Metals Refineries for further processing.During the smelting and converting processes two distinct gas streams are produced.The Peirce Smith converter off gas contains 4% - 9% SO2 which is treated in a conventional Sulphuric Acid Plant to produce sulphuric acid (H2SO4).The electric furnace off gas contains 0.9% SO2 and was (until September 2002) vented through a 91 meter high stack to atmosphere.Off gasses which contain less than 3% SO2 is difficult to handle and quite a few processes had been developed over the years to cope with this gas. A broad spectrum of process suppliers and technology approaches is available and the different technologies can be divided into a few main approaches i.e.Scrubbing of the off gas with an alkaline solution to produce an environmentally friendly and stable waste product which can be discharged onto a tailings dam or permanent landfill site.Physical absorption of the SO2 into a chemical solution to produce high quality chemically pure process chemicals.Catalytic reaction of SO2 with O2 to produce SO3 which is absorbed in water to produce sulphuric acid of less than 90% strength.In October 2002 Impala Platinum commissioned a Sulfacid Plant at its Smelter in Rustenburg which recovers the SO2 from the electric furnace off gasses into a weak sulphuric acid solution.The Sulfacid Plant technology is widely used in the paint pigment industry. This is, however, the first application of the technology on electric furnace off gas.The furnace off gasses contains flue dust which is removed in electrostatic precipitators. The gas exiting the precipitators normally still contains between 40 mg/Nm3 and 60 mg/Nm3 dust and passes through a quench-scrubber before entering the reactors. The quench-scrubber cools the electric furnace offgas down from ± 200 °C to 60 °C and act as a final dust removal stage."

Jan 1, 2003

By A. Collings, A. Farmer

"Power ultrasound may be used in the processing of mineral suspensions to clean the particle surfaces of oxidation products and fine coatings, mainly through the large, but very localised forces, produced by cavitation, which is the formation and sudden collapse of bubbles in a fluid. Cavitation occurs preferentially at solid surfaces in a liquid: at container walls, inserted objects or suspended particles. When the cavitational bubbles collapse near a solid they do so by forming a very high energy jet directed from the point on the bubble furthest from, and directed towards, the surface of the solid, in effect micro jet blasting.This paper highlights some of the major mineral processes where ultrasonics is beneficial namely: Surface cleaning of detrital mineral particles, where container quality glass sand was upgraded to tableware quality and up to 20% improvements in the sharpness of high tension separation of mineral sands was achieved"

Jan 1, 2003

By N. T. Beukes, W. Banda

Recovery of Co from slag is a recent advancement in the extractive metallurgy of nonferrous metals. In this study a DC arc technology at laboratory scale has been applied to investigate the selective recovery of Co from slag, under three different flux types with an emphasis on influencing the activity of FeOx, SiO2 and CoO in the slag. It is known that reduction of slag by carbon is only up to a certain level after which, the recovery will depend on the chemistry of the slag, hence the need to modify the slag chemistry. Two power settings were employed to induce higher temperatures and aggressive agitation. The results were interpreted by comparing how much Co and Fe was in the slag and alloy. TiO2 reduced the amount of Fe in the product alloy compared to when CaO and CaF2 were used. The change in power did not seem to have had a major effect on the recovery although the amount of material lost to flue dust was more at a higher power rate.

Jan 1, 2003

By N. Kgabi, F. B. Waanders, E. Vinken, A. Mans

"Mössbauer and SEM identification of the iron mineral phases present in South African coal fractions from the Free State, Gauteng, Mmpumalanga, Natal and Waterberg coal fields, as well as from ash samples from coal used in the Lethabo power plant, containing a large amount of inorganic matter, was conducted. The iron is mainly associated with sulphur in the mineral but the amounts of these and other minerals vary considerably in coals from diverse origins. By means of Mössbauer analyses the iron bearing minerals were identified as pyrite, jarosite, illite and ankerite. In the SEM analyses quartz, associated with various clay minerals was identified with differences in abundance found between the coals from the different locations.The fly ash, produced at the high combustion temperatures in the power plant, gave rise to a spectrum, typical of a glass. SEM analyses showed that agglo- meration of the fly ash was due to the presence of Ca in the coal. The lab. produced fly ash was combusted at temperatures ranging from 200-1 200°C and the pyrite changed partially to hematite and partly into the glass due to the presence of the quarts and the clay minerals. A similar spectrum as the power plant fly ash spectrum was obtained.In the weathering experiments the pyrite changed to a sulphate component in a very short time during air drying."

Jan 1, 2003