Search Documents

By Paulo Castillo, Cesar Gomez, Jaime Alvarez

Operations using flotation to produce mineral concentrates require testing of frothers to characterize their ability to preserve bubble formation size and to build a stable froth. Many techniques have been proposed to measure parameters associated with these two roles. These techniques focus, in general, on only one of these roles and are based on special equipment operated at conditions quite different from those existing in industrial cells and columns. Both roles have been simultaneously characterized in a laboratory flotation column, but the requirements associated with the installation and operation of one of these units, are a serious limitation for its use on-site. A technique based on the use of a laboratory mechanical cell, a common piece of equipment in operations, will have wider application. Establishing the ability of a frother to control coalescence by preserving bubble formation size is done through bubble size measurements as a function of frother concentration. Froth build-up and stabilization is associated with the amount of water carried by bubbles into the froth layer, which has been demonstrated to correlate with the gas holdup in the collection zone. Procedures devised for determining the critical coalescence concentration (CCC) from measurements of bubble size as a function of frother concentration, and the gas holdup by collection of water displaced from the cell by the presence of bubbles at different frother concentrations, were tested. Three analytical-grade frothers were utilized: a straight-chain (1-heptanol) and a branched (MIBC) alcohol and a polyglycol (PPG425). The results obtained at a standard set of conditions, demonstrated consistent differences between these frothers, and the ranking from least to most effective for reducing bubble size or decreasing water drainage followed the same sequences found when more complex frother characterization techniques are used.

Jan 1, 2014

By Z. Kwela, A. Manhique, W. W. Focke, W. van der Merwe

"The main features of the de Wet improved alkali fusion process for the manufacture of AZST are: Fewer process are steps necessary; radioactivity is removed by leaching rather than by precipitation; fewer waste streams are generated; there is less waste to discard and alkali reagent is recovered in the form of a sodium silicate solution that is essentially free of radioactivity.Here we report on our efforts maximize the alkali recovery in the sodium silicate product stream: Milled zircon, d50 ˜ 9 µm, was fused with caustic soda pearls in open reaction vessels at temperatures between 650°C and 850°C. Fusion times of 1, 2, 4, 24 and 336 hours (with intermittent milling) were investigated. The fusion products were characterized by infrared spectroscopy, X-ray diffraction and by wet chemical analysis.For prolonged fusion times the fusion products approached equilibrium compositions. However, the phases Na2ZrSiO5 and Na4Zr2Si3O12 observed at 850°C did not form at 650°C. Since these compounds do not hydrolyze in water they limit the recovery of alkali in the sodium silicate product stream. For 2-hour fusions a broad spectrum of non-equilibrium reaction-products, that are rich in sodium silicates, is formed."

Jan 1, 2003

By J. Kwon, D. Lee, H. Cho

"The use of the combined grinding and liberation model to predict liberation characteristics of iron ore comminuted by a ball mill was studied. Comminution characteristics were obtained using the one-size fraction method. The iron ore samples were crushed and separated into a number of narrow size fractions by screening. The size fractions were further divided by magnetic separation into three classes: concentrate, middling, and tailings. Subsequently, various size-grade classes were subjected to ball milling, and the results were analyzed in terms of the kinetic grinding model. The mineralogical textures of the grinding products were analyzed using mineral liberation analysis. The distribution of iron content within the size fractions was characterized by the beta distribution combined with the Andrew–Mica diagram. It was found that the grinding characteristics of the iron ore samples varied slightly with the iron content. However, the liberation characteristics were well described by the same set of liberation model parameters, regardless of composition. The variation in grinding kinetics with composition and the liberation model parameters was used in the combined comminution–liberation model to predict the evolution of the size-composition matrix as grinding proceeded. The predicted results agreed well with the experimental results. The developed model can be used to construct the yield–recovery graph and to calculate the liberation efficiency to determine the size reduction threshold for efficient separation. INTRODUCTION In mineral processing, comminution is usually the first step that ores undergo to liberate valuable minerals from gangue minerals. Generally, as the particle size decreases, higher liberation can be achieved. However, excessively small particles are unfavorable to subsequent processes, such as separation. Moreover, comminution is a highly energy-consuming process itself that accounts for approximately 60% of all energy used for processing. Therefore, there is a definite need to increase energy efficiency by applying adequate stress so that a high degree of liberation can be acquired at the coarsest size without overgrinding. To this end, it is essential to develop a model to predict the liberation of minerals as a function of size reduction."

Jan 1, 2018

By Valentin V. Shatalov, Irina V. Pastukhova, Alexander V. Kurkov

"We have developed a technology to improve the quality of low-grade concentrates containing minerals of tantalum, niobium and tin on the basis of given conception by the way of improving selectivity and using certain reagents composition. The basic collector presents a traditional or complex-forming collector used together with organic diphilic reagents – the secondary reagents regarding the basic flotation regiment, capable of forming associates with the main collector on the surface of the mineral, thus altering the interaction energy. In the given process the main collector is the fraction of hydroxamic acids C7-C9, the reagent of the secondary action – sulphosuccinamate, which added in moderate concentrations range provides for a synergistic effect.We have determined the parameters of the process stability and necessary modifying reagents for a selective recovery of tantalum, niobium and tin minerals from refractory products. Variants have been studied where the main collector and the secondary action reagent were substituted with some more efficient flotation reagents. A possibility of a more flexible reagent compounding for the process has been shown. The flotation process is highly stable regards the saline composition of the liquid phase in the pulp. It can operate under conditions of the complete water recycling with the total salt content up to 12 kg/m3, iron up to 1.2 kg/m3.The given results consider the efficiency testing of the suggested technology for the gravitation products, which were obtained from ores of various genesis and contain large quantity of the most refractory minerals, such as topaz (80%), gamet (55%), tourmaline (30%). High selectivity of the process has been registered with the metal recovery about 92-98%, which appears to be similar to hydrometallurgical operations under certain conditions."

Jan 1, 2003

By Peter Ay, Matthias Schmidt, Christian Stollberg

"The aim of the study is the development of a seamless reprocessing procedure for plastics from automotive parts which are to be recycled (figure 1). Before automatic sorting can be performed, the materials first have to be identified by a near and middle infrared (NIR/MIR) system.Materials reprocessing basically includes research on size reduction, decoating, and roughening of the materials. Variants of the necessary technologies such as different shredders and mills and physico-chemical or mechanical decoating and roughening procedures together with the fundamental approaches underlying these methods are investigated and benchmarked. This allows the theoretical determination of the impact of each method not only on the overall process but also on the result achieved within the identification and sorting procedures."

Jan 1, 2003

By K. W. Stöckelhuber, A. Wenger, H. J. Schulze

"An important elementary step of the flotation process is the forming, drainage and rupture of a thin intervening liquid film between bubble and mineral particle.After the encounter of the bubble with the solid surface a wetting film is formed. The initial thinning of this film is driven by the capillary pressure inside the bubble. When the film has reached a certain thickness rupture can take place.There are two possible mechanisms describing this process:-, Growing fluctuation waves (spinodal dewetting) on fluid interfaces under the influence of any kind of attractive forces (electrostatic, van der Waals). -, Nucleation inside the film.Metastable wetting films on negatively charged, hydrophobic glass surfaces (gaseous phase methylated), or on hydrophilic, positively charged glass surfaces (with Al3+ ions), have been analysed by means of the kinetics of film thinning according to the Reynolds law. These experiments demonstrate that both mechanisms can be responsible for the rupture of a thin wetting film. In the case of hydrophobic surfaces the nucleation mechanism is preferred; in the case of opposite charged silica surface the capillary waves mechanism due to an attractive electrostatic double layer force between silica and air bubble takes place.Hereby the existence of a long range hydrophobic force. on a hydrophobic surface can be excluded. The apparent interaction can be explained by the presence of gas nuclei formed on heterogeneous surface sites. The results provide deeper insight into the mechanisms of wetting film stability, adhesion process in flotation and droplet coalescence."

Jan 1, 2003

By Claudia Ríos Figueroa, Gonzalo Montes-Atenas

"Among the many variables mentioned in the literature that may influence the froth flotation performance, particle size is perhaps one of the most renowned. Empirical knowledge has indicated that recovery of fine particles will inevitably drop below certain particle size threshold. Several processing alternatives have been suggested to improve the recovery of fine particles. Some of these initiatives have been reached the status of patents and other intellectual property related documents; however, there is still a disconnection between the scientific knowledge available and the industrial operations practicalities implemented to address this matter. In fact, in general terms, none of these ideas or processes concepts have become a final solution to this problem. At first glance, economical reasons may be argued as the main cause hindering the development of these and other ideas, but it would be an oversimplification as technical issues behind them are still themes to be discussed and sorted out. This study aims to review technical aspects behind scientific ideas and processes concepts suggested to solve the problem of low beneficiation of fine particles in froth flotation. The analysis was performed using the theory of inventive problem solving (TRIZ) which allows identifying technical gaps these initiatives have not considered or overlooked. Statistically the scientific databases indicates that reports on fine particles froth flotation only represented less than 50% of all reports involving fine particles processing. Most of the solutions derived from classic contradictions derived from bubbles and particles hydrodynamics only (reducing the bubble size or increasing the turbulence would increase the rate of bubble-particle aggregates formation but may reduce the recovery). This contradiction encompasses a small range of contradictions possible to be accounted and to be resolved. The method is expected to provide insights towards designing definitive solutions for the industry in this field."

Jan 1, 2014

By Khoi Nguyen, Luke Keeney

"Hardness" is an important yet diverse material physical property and is a key parameter in the mining industry in fields such as comminution, geotechnical and blast modelling. Several laboratory and field based measurement techniques exist to measure hardness (e.g. Point Load Testing, Vickers, Brinell, A*b, BMWi, UCS), all are designed for specific applications. Current tests are generally destructive and require specific sample preparation procedures which results in high cost tests that are not conducted in adequate quantities to map hardness across an ore body. The EQUOtip rebound hardness tester is a device that has been developed for application in ore body hardness domaining within the AMIRA P843 GeMIII Research Project. The rebound hardness test is non-destructive and suitable for application on half and whole diamond drill core. Data acquisition protocols and a data processing software application (EQProcess) have been developed to facilitate routine collection of comparative hardness information. This paper outlines the data acquisition and processing methodology and provides application examples of defining relative hardness domains in different geological deposit styles.

Jan 1, 2014

By Gülay Bulut, Ünzile Yenial

"Water composition has a significant effect on flotation. A better understand the role of water composition in flotation is very important for process quality and performance. Based on source of process water, the concentrations of the dissolved ions, hardness, contaminants and residual composition of reagents can varied in the process water. The various water resources employed during lead and zinc flotation caused activation, depression or selectivity effects on minerals due to the presence of different ions in solution. Metal ions in these water resources were adsorbed on the ore, whilst ions associated with gangue minerals were released into the flotation pulp.This paper includes a research for the effect of different water compositions on lead and zinc sulphide flotation. Experiments were carried out five types of water such as tap water, recycling water, tailing dam water, underground mine water and sea water. The ore sample was obtained from Esan Balikesir-Balya mine. The mineralogical study of ore sample shows that it contains mainly galena, sphalerite, pyrite, hematite, quartz, diopside, epidote, calcite, and chlorite. It is found that recycling water and tailing dam water has a positive effect on recovery of lead and zinc minerals and detrimental effect on content of both minerals. This result may explain with remaining reagents in these waters. Underground mine water and tap water gave nearly the same recoveries of zinc. Sea water affects the recovery lead and zinc negatively."

Jan 1, 2014

By A. Morrison, D. Mesa, P. R. Brito-Parada

"Froth flotation is the most widely used mineral separation technique. It is based on the relative hydrophobicity of valuable and gangue particles. In a flotation tank, two distinct zones can be identified: the pulp and the froth. The pulp is a turbulent region in which hydrophobic valuable particles attach to air bubbles while hydrophilic gangue particles remain in the slurry. As the particle-laden bubbles rise, a mineralised froth zone is formed that overflows as a concentrate. Although the process is more than a hundred years old, there remain many aspects that are not completely understood, particularly for the froth zone. Thus, the rules governing the design of flotation tanks tend to focus on pulp zone parameters, which are largely based on operating data. An example of this is the design and operation of impellers. These tend to be designed paying attention to hydrodynamic phenomena in the pulp zone, but their effect on the froth zone has not been completely addressed. The role of impellers in a flotation tank is to break the air bubbles in order to generate smaller ones and to provide an environment that enables the collision between those bubbles and the particles in the slurry. This usually creates turbulent regimes that can affect the pulp-froth interface, destabilising the lower regions of the froth and affecting the overall performance of the process. Different impeller designs and retrofit modifications have been proposed in the past, addressing some of those issues. However, there is no systematic study of the effect of different impeller designs on the bubble size in the pulp and its links to the stability of the froth. This work tested the impact of an impeller designs combined with the use of a stator on the performance of an 87 litres continuously operated laboratory-scale flotation tank, with a focus on bubble size in the pulp and froth stability. The results showed that the implementation of a stator system decreased bubble size and increased froth stability. That resulted in an increase of mass pull, measured as a proxy of metallurgical recovery."

Jan 1, 2018

By Claudio Bisso, Javier Vargas, Charles Lozano

"This paper summarizes the activities performed to predict SAG milling throughput at Minera Esperanza. Having highly reliable geometallurgical models aided by the new computer tools and specific metallurgical testing to rely on has become a major issue in recent times due to their impact on the business. Minera Esperanza’s SAG throughput model was constructed by characterizing the ore feed and operational parameters of the plant. Producing a robust model required satisfying number of requirements for the parameters used for both the ore and the plant as follow: 1) geologic and geometallurgical characterization parameters; and 2) parameters of a plant running at the rated production under optimum operating conditions. Obtaining these parameters required increasing the quantity of samples and metallurgical testing through drilling campaigns, mapping the drill holes and putting samples through various comminution tests while sampling all operational flows at the plant to obtain the metallurgical information for the operational parameters. The information was entered on the JKSimMet software to enable a throughput model to be developed to output SAG mill throughput predictions that are very close to actual throughput figures, i.e., accurate within a range of 2% on a monthly basis."

Jan 1, 2014

By B. McFadzean, J. Taguta

The enthalpy of immersion is the heat change arising from the replacement of the solid-gas interface with the solid-liquid interface when a solid surface is immersed in a liquid. Although immersion calorimetry has been established as a valuable and reliable means of determining solid surface properties such as wettability, it has seldom been applied in mineral processing research. In this study, precision solution calorimetry was employed to measure the enthalpies of immersion of different minerals in water. The enthalpies of immersion were then related to the first-order flotation rate constant as determined by the microflotation technique. The same measurements were also made on sulphide minerals whose surfaces were modified to different degrees of hydrophobicity using different percentage coverages of amyl xanthate collector. The enthalpy of immersion technique was capable of distinguishing and ranking minerals according to their wettability. All mineral types and collector-treated minerals conformed to the same relationship that was found between the enthalpy of immersion and the flotation rate constant. This conformed, empirically, to a power law equation. As the enthalpy of immersion decreased, there were large increases in flotation response for very small changes in hydrophobicity. In addition, a critical enthalpy of immersion (CEI) was found, above which no flotation could occur. The scatter in the data points could be corrected for by adjusting the rate constant using the density of the minerals to produce a robust relationship between the rate constant and enthalpy of immersion. These results have shown that the enthalpy of immersion is able to indicate both the natural mineral hydrophobicity and the extent to which collectors can render a mineral hydrophobic. This technique has considerable potential to be used as a sensitive and accurate measure of mineral surface wettability in order to predict flotation performance.

Jan 1, 2018

By Vladimir G. Kochnev

"Autogenous and semi-autogenous grinding (AG and SAG) have been considered a step forward in comparison to conventional grinding circuits with several stages of crushing and using ball (and/or rod) grinding mills. However, existing AG and SAG technologies still can be improved and have an immense potential from the viewpoint of economic benefits.Experience gained by the Technics & Technologies of Disintegration Ltd. (TTD) in the research of grinding processes shows that comminution in AG and SAG mills can be performed in a more effective way. The company’s approach comprises the following elements:- Novel mill design- New liners and lifters- Novel discharge grid design- Technique of treating material of critical particle sizeA novel mill of the cantilever type capable to operate in the AG and SAG mode has been developed. The cantilevertype mill has a high diameter to length ratio, which dramatically increases the throughput rate, and is characterised by high reliability, fast installation and low capital and operating costs.Tests of the new heel-shaped liners, originally aimed at improving the intact condition of diamond, indicated that they play an important role in the grinding process. Tests performed by TTD jointly with ALROSA, MINTEK and Anglo-American Corporation, demonstrated that the heelshaped liners provided the increase in the throughput rate varying from 30 to 80 % and the decrease in power consumption in the range 30-55 % for grinding of kimberlite and platinum-containing ores.Investigation of the influence of the main grid parameters on the efficiency of grinding led TTD to a special design of a mill discharge grid, with a radial location of openings, the slot width varying from the periphery to the centre and the grid surface provided with “heels”. The design allows one to control the particle size distribution of the ground product without affecting the grid throughput rate."

Jan 1, 2003

By Lutz Rolf, Halit Z. Kuyumcu, Salas Cazón. Milton A.

Aim of experimental investigations was the mathematical description of the abrasion process running with a single particle stress. This is on the one hand the basis for the physical interpretation of the process, on the other hand the base for the simulation of abrasion processes carried out in technical scale. With this investigation for the first time the influence of the particle shape changing with increasing abrasion progress was quantitatively described. This influence affects itself particularly strongly on break-fresh particles up to an abrasion degree of approximately 10 to 20%. This is for the description of technical processes the most interesting area.

Jan 1, 2003

By Scott C. Brown, Brij M. Moudgil, Ivan U. Vakarelski

The manipulation of the apparent hydrophobicity of particlute surfaces is necessary to achieve optimal selectivity in flotation processes. Previously a number of works have investigated the role of microscale surface and particulate morphologies on chemically modified substrates. These works have suggested that microscale surface asperities lead to an increase in flotation efficiency by assisting in the rupture of wetting films. Yet, in mineral processing the presence of surface asperities may lead to a reduction in flotation. The reason for this may-in part-be due to the presence of nanoscale irregularities at the interface. In this work, it is proposed that the presence of roughness at the nanoscale may have a dominant impact on the apparent hydrophobicity of mineral surfaces during flotation. It is suggested that as inter-asperity seperation distances are reduced capillary effects are enhanced for high energy mineral surfaces leading to the formation of liquid domains, which adversely impact hydrophobicity. In addition, as these distances approach the surfactant headgroup size obstruction of surfactant self-assembly process may occur, thereby further limiting flotation.

Jan 1, 2003

By Chris J. Martin, Nichola A. McKay

"In mid-2001, North American Palladium commissioned a new 15,000 tonnes per day milling and flotation circuit at their Lac des Iles Mine (LDI), one of only two primary platinum group element (PGE) producers in North America. The mill treats an ore containing 2.3 g/t PGE producing a concentrate assaying 300 g/t PGE, at a recovery of roughly 75%.Top-size control crushing is conducted ahead of semi-autogenous milling. A portion of the SABC circuit feed is crushed to –25mm to increase mill throughput. Product from the SABC circuit is fed to flotation. Flotation consists of roughing and scavenging, with the rougher and scavenger concentrates each being reground using vertimills. Cleaner flotation uses two stages of cleaning using mechanical cells, and a third stage using flotation columns, the column tails being scavenged using a bank of mechanical cells. Rougher concentrate by-passes the first cleaner circuit. Reagents added include amyl xanthate collector, dithiophosphate promoter, MIBC frother and a carboxy methyl cellulose-based gangue depressant.SGS Lakefield Research, together with staff at LDI initiated a structured plant optimisation program comprising on-site testing, bench-scale flotation and mineralogical analysis using QemSCAN. The objectives of the mineralogical studies were 1) to identify feed PGM, their size distribution and mineral associations, 2) establish relationships between the PGM mineralogy and PGM floatability, and 3) characterize the culprit silicate minerals diluting the final concentrate.PGM flotation response at Lac des Iles is clearly bi-modal in nature, with about 60% of the PGM floating quickly, to a high value rougher concentrate. The mineralogical work was able to explain the causes of the bi-modal PGM floatability, which in turn created new opportunities for the metallurgists to optimise the circuit."

Jan 1, 2003

By Ghislain Bournival, Seher Ata, Yesenia Saavedra Moreno

"In froth flotation, frothers are commonly added to the pulp to modify the interfacial properties of bubbles. These properties may be modelled using commercial software packages. The volume of fluid (VOF) method was used to track the interface motion during the post-rupture oscillation of the newly formed bubble. The aim of this research was to provide an insight into the modelling of viscoelastic phenomena through the coalescence dynamics of two bubbles in solutions of various surface tensions using a three-dimensional computational study. Different surface tensions were used to simulate changes in methyl isobutyl carbinol (MIBC) concentration. The computational results were evaluated by comparing the oscillatory motion of the newly formed bubble for the different MIBC concentrations. For known MIBC concentrations, the deviations of the computational damping constants from the experiments were quantified, revealing possible deviations in the VOF surface tension model. In addition, the analysis provided insight into the flow patterns of the fluids and the effect of frother concentration on the velocity magnitude in the liquid and air phases. This analysis provided a further understanding of coalescence dynamic and post-rupture oscillation in froth flotation. Such a process is believed to affect the stability of particles at the interface due to the release of surface energy when the bubble surface is reduced.INTRODUCTIONIn froth flotation, bubble coalescence is an important phenomenon that is highly dependent on the interfacial properties of the liquid film between bubbles. It is known that the frother adsorption at the liquid-air interface changes the interfacial properties, resulting in an increase of surface elasticity and reduction of surface energy (Pugh, 2016). However, in a two-phase system, it is the frother type, concentration, frother molecule conformation at the interface and viscoelasticity properties that dictate film stability (Pugh, 2016). The viscoelasticity phenomena can be explained in terms of surface viscosity, which quantifies the energy dissipation at the interface and surface elasticity that represents the energy absorbed at the interface as result of bubble oscillation (Pugh, 2016). In the case of systems stabilized by nonionic frothers, it has been shown that surface forces alone do not account for film stability, but the viscoelasticity represents the ability to damp external disturbances in the thin film separating the bubbles and prevent coalescence (Santini et al., 2007)."

Jan 1, 2018

By Kazutoshi Haga, Atsushi Shibayama, Altansukh Batnasan

"The aim of this study was to develop a hydromellurgical processing for removal of arsenic from high-arsenic copper sulfide ores and concentrates, providing increase in copper recovery. In this study, three different enargite ore samples containing 28.2–46.7% copper, 1.9–15.0% arsenic and 10.6–27.5% iron were used to determine optimum conditions for the extraction of copper and removal of arsenic. High pressure oxidative leaching process was preformed using various leaching reagents such as sulfuric acid (H2SO4), ferric sulfate (Fe2(SO4)3), hydrochloric acid (HCl), ferric chloride (FeCl3), sodium sulfate (Na2SO4), sodium chloride (NaCl) solutions and distilled water (DW), respectively, under the fixed conditions which were selected to be as follows: NaCl concentration, 0.34 M; concentrations of other leaching reagents, 0.1 M; particle size, -45 ?m; pulp density, 100 g/L; agitation speed, 750 rpm; leaching temperature, 160 ?C; leaching time, 60 min and total pressure (oxygen gas and vapor pressure) into an autoclave, 1 MPa. Results show that under the leaching conditions, more than 90% of copper leaching was achieved with lower than 2% arsenic content as a consequence of the formation of arsenic precipitates in a solution of Fe2(SO4)3–NaCl. It was determined that copper, arsenic and iron concentrations in the pregnant leach solution were 42 g/L, 0.3 g/L and 0.3 g/L, respectively. As a result, it can be concluded that the Fe2(SO4)3 solution in the presence of NaCl or FeCl3 are more efficient leaching media compared to other leaching agents under the high pressure oxidation conditions, because of their high copper recovery and lower arsenic level in the pregnant leach solution.INTRODUCTION Generally, copper is usually produced from copper sulfide ores by a combination of several processes which are flotation and smelting followed by refining [1-3]. Arsenic content in copper sulfide ores tends to increase due to the depletion of high grade copper deposits, hence conventional mineral processing and metallurgical processes cannot effectively treat these ores containing high levels of arsenic to obtain consistently high purity copper concentrates. Because high levels of arsenic in copper ores/flotation concentrates reduces the value of concentrates due to the restriction of smelting process and causes it to be a source of environmental pollution [4-6]. From this point of view, the known way of prevention against high-arsenic copper sulfide concentrates in further metallurgical treatments is to develop economically and environmentally competitive technologies for removal of arsenic impurity from copper sulfide ores before treating the ores/flotation concentrates by the pyrometallurgical routes."

Jan 1, 2018

By K. Malysa

Bubble collisions with ore grains and a selective formation of the bubble-grain aggregates are necessary steps for flotation separation of useful and gangue components of an ore. For the attachment of valuable mineral grain to the colliding bubble a liquid film, separating the bubble and the grain needs to rupture during short time of their collision. High hydrophobicity of the grain surface is favorable because stability of the separating (wetting) film is much lower at such surfaces, that is, the film ruptures faster and at greater thickness. Simultaneously, it needs to be kept in mind and taken into consideration that high affinity to air is a typical feature of hydrophobic surfaces. Thus, when the hydrophobic surface is immersed into aqueous phase the air can stay attached to such surfaces and affect kinetics of the bubble attachment. The paper presents results and analysis of dynamic phenomena occurring upon the collision of the rising bubble followed by its attachment to hydrophobic (Teflon) plates of different roughness. The influence of the Teflon surface roughness, solution concentration, bubble size and impact velocity on bouncing of the colliding bubble, time of the three phase contact (TPC) formation and drainage time of the liquid film, formed between the solid and bubble surfaces, is described. High hydrophobicity, as showed earlier (Malysa et al, 2005), does not assure that each collision leads to the TPC formation and attachment of the colliding bubble. Roughness is the parameter of crucial importance for kinetics of the bubble attachment to hydrophobic surfaces (Krasowska and Malysa, 2007; Krasowska et al, 2009; Kosior et al, 2011). Enlarged roughness of the Teflon plate, from ca. 1 to 80µm, results in shortening the time of the TPC formation (bubble attachment) by over an order of magnitude - from 105 to a few milliseconds only. Higher surface roughness means that larger amount of air can be entrapped in bigger scratches and cavities of the Teflon plate during its immersion into aqueous phase. Results documenting importance of the air presence are showed and mechanism of the air facilitated TPC formation and bubble attachment to hydrophobic surfaces is described. Keywords: bubble collisions, hydrophobic surfaces, teflon plate roughness, TPC formation

Sep 1, 2012

By C. Stollberg

The recovery of valuable materials from electronic waste is of growing importance for the re-source management not only in the industrialized nations. Being a significant step in an innovative automated process for recycling of metals and plastics from used electric and electronic equipment, the results of the work introduced below, prove the applicability of microbial leaching of metals from printed circuit boards (PCBs) at industrial scale. Within the first project step, which started in March 2005, experiments in shaking flasks with a mixed culture of chemolitotrophic bacteria (mainly Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans) were carried out to study the solubilization of non-ferrous metals present in the electronic waste. It was found that the best results were achieved by means of a two-stage process in which leaching of these metals was carried out by acidified ferric sulphate solutions generated as a result of the prior bacterial oxidation of ferrous ions to the ferric state. Special reactor systems for bacterial generation of such solutions and for the subsequent leaching of non-ferrous metals from the waste were developed, constructed and tested under laboratory and pilot scale conditions. The optimum technological parameters such as concentration of iron ions, pH-value, temperature and presence of nutrients were established for both reactor systems. Parameters such as particle size, pulp density and flow rate of the suspensions being leached were established for the leaching process carried out under continuous-flow conditions. The complex flow sheet reflects a highly efficient technology on the basis of metal recovery, environmental effect and economical acceptance. The process was successfully implemented into an industrial demonstration unit.

Jan 1, 2014