Search Documents

By John A. Herbst, Ming Song, Xiangjun Qiu

"It has been known for sometime that as wear occurs in tumbling mills there is an associated change in mill throughput. These changes have traditionally been simplistically, attributed to “mill volume effects”. New high fidelity simulation (HFS) tools (involving DEM, CFD and Breakage models) are now giving new “microscale” insights into the complex interactions that occur between evolving lifter/liner profiles and breakage. An illustration of this analysis is shown in Figure 1 below.Here we see that after a new lining is installed (Region I) the wearing process reduces the liner thickness resulting in a larger power draw and an associated higher throughput until Region II is reached. By this point the lifter height is reduced significantly changing charge motion (less cataracting) the power begins to decline, but the comminution efficiency increases with this type of “calmer” breakage environment therefore the throughput continues to increase. In Region III the lifter is no longer providing the minimum required charge lifting action, the power and the throughput both drop off significantly. In the last two stages the behavior is especially complex because throughput is not linearly related to power since grinding efficiency is changing.The study described here shows that these new HFS tools allow the design of wear part profiles which will maximize mill productivity over the entire life of liner/lifter systems. A simple example of such a design procedure is shown involving the selection of a sinusoidal profile for a 34 ft diameter SAG mill.The paper discusses how the principles exposed in this simple example can be applied to search for an optimal profile in which non-standard modifications are allowed to compensate for throughput or wear shortcomings of standard profiles."

Jan 1, 2003

By Muammer Kaya, Sait Kursunoglu

"Energy is the major concern for society. It is expected that developing country economies and populations will grow and consume more energy. Interest in nuclear power is rising, while the world looks for non-depletable energy source that will not contribute to global warming. However, it still has concerns of nuclear proliferation, radioactive waste and safety. It is necessary to overcome these concerns if nuclear energy is expanded to developing countries. Thorium (Th) utilization as nuclear fuel will be an opening key of these difficulties because Th produces less Plutonium (Pu) and less radioactive waste with enhanced safety. Research into the use of Th as a nuclear fuel has been taking place over forty years, through with much less intensity than that for uranium (U) or U-Pu fuels. Nuclear industry is currently using only 0.7% of the available energy from mined U. With huge resources of Th and relatively little U, Turkey has made utilization of Th for large-scale energy production a major goal in its nuclear power programme. Thorium fuel is plentiful and inexpensive. Energy is major concern for developing Turkish society. Turkey, today exports more than 70% of its energy as fossil fuels. In the last 50 years, Turks are skeptical, anxious and indecisive about having nuclear energy for electricity production. In the last 10 years, Thorium is brought into Turkish government’s attention and national discussion as a new, safe, clean, affordable, CO2-free, alternative, strategic and domestic nuclear energy fuel. Turkey recently contacted four VVER-1200 type Russian Nuclear Power Reactors using U as a fuel in Akkuyu (Rosatom) and another four units will be established in Sinop in the next decade by Japan (Mitsubishi-Westinghouse). Turkish nuclear programme must envisage use of domestic Th as a fertile material. This paper briefly reviews the developments of Th-fuel cycle for nuclear energy from global and Turkish perspectives. Previous Th reserve development and recovery studies from Turkish bastnasite ore are summarized in this paper."

Jan 1, 2014

By R. X. Li

The overall flow-sheet of producing chromium (III) sulfate is described in this paper. The suitable conditions of each process such as sintering, leaching, aluminum removal, reduction, and de-composition conditions were experimentally studied. The results show it is reasonable to produce chromium (III) sulfate with the flow-sheet pointed out in this research work. The final product is Cr2(SO4)3 solution contained 150~250g/L Cr.

Jan 1, 2014

By B. Q. Xiao

The nitrate content is an important factor for environmental water samples and flour. In a 0.35 mol/L H2SO4-2NO solution, has a strong catalyzing function on the decolourization of Gallocya-nine (GC) oxidated by NaBrO3. Based on this, a novel method was developed to measure the NO and -3NO concentrations in water and flour. The flow injection technology was introduced into the analysis system. A single-valve dual- cingulums to inject which the Copperized-Cadmium slice and the reduction zone are isolated. The optimum solution for this method contains 1.48×10-4 mol/L GC, 0.06 mol /L NaBrO3 and 0.2 mol /L of NH4-2NOCl. Two empirical equations were proposed to calculate the and -3NO concentrations based on the measured signals. It can be used to measure -2NO of from 0.001 mg / L to 2.0 mg/L and -3NO of from 0.002 mg / L to 2.5 mg/L. The measurement frequency can be up to 20 samples / h. The relative standard deviation for eleven samples is less than 5%.

Jan 1, 2014

By G. V. Kalabin

"The paper supports applicability of satellite imagery at regional and local level for rapid quantitative assessment of natural environment in zones of activity of mining complex enterprises. Exacerbation of environmental problems during mineral mining and processing associated with their scale and geography of field distribution through the vast territory of our country requires constant monitoring of natural environment status, which necessitates engagement of space surveillance nowadays. It is proposed to use the monitoring of land cover and land use at regional and local level for the environmental assessment of a particular production or complex productions. You must establish the dependence of NDVI change trend with the magnitude of anthropogenic impact on the source or multiple sources of environmental pollution a particular area.. We present the results of studies of vegetation remote sensing methods in a number of territories placing mining enterprises. INTRODUCTION Ensuring a healthy environment is necessary both in untouched areas and disturbed. The condition of the developed territories should be monitored with particular attention, since the restoration of the disturbed territories requires great efforts and financial costs. More narrowly, the health of the environment (Zakharov V.M. and etc.,2001) means its quality ensuring the health of man and other species of living organisms, which includes two aspects (Zakharov V.M. and etc, 2000): - ensuring an environment conducive to human health as a biological species: - maintaining the health of the natural environment, i.e. its constituent species of living organisms and plants. The consequence is the disturbance of natural ecosystems, which determines the quality of the environment, favorable for human habitation and the state of health of the population in total determine the status of the territories where enterprises for the development of georesources are located and allow them to be ranked according to the degree of environmental danger. Without knowledge of the trajectory of ecosystem successions, it is impossible to offer adequate requirements for the technologies used to ensure the implementation of the preserved natural potential after the removal or reduction of man-made stress."

Jan 1, 2018

In this paper High Pressure Grinding Rolls(HPGR) was utilized to pretreat CVRD southern specular hematite for enhancing the pelletization of the refractory hematite. The process parameters of HPGR, balling and firing were optimized, and the mechanism of HPGR was demonstrated by determining the surface activity by means of Blaine specific surface area tester, laser size analysis, scanning electron microscopy (SEM),X-ray diffraction (XRD), micro calorimeter and pelletability index. It is shown that the pelletization of the refractory hematite was greatly improved. The drop strength of green balls increases from 3.4 times to 13.6 times from 0.5m height while the bentonite dosage decreases from 2.2% to 1.3%.The compressive strength of roasted pellets also reaches 2500N/pellet. The mechanism of the pretreatment of CVRD southern specular hematite concentrates by HPGR is revealed that the surface activity is improved by an increases in specific surface area and the amount of micron size fractions, and higher lattice deformation and defects due to the fractures occurring inside particles during static pressure comminution, resulting in more wetting enthalpy, higher pelletability index and good property of roasting.

Jan 1, 2014

By Yimin Zhu, Dezhou Wei, Haijun Liang, Zhifu Zhou

Pyrite is one of sulfide minerals most widely distributed in the earth. During the flotating separation of metal sulfide and the floating desulfation of coal, it is often requaired to restrain pyrite. However, the result is not very satisfactory because of the little difference of floatability of minerals to be separated. The problem is extremely outstanding for the floating desulfation of coal. Researchers carried out a number of experiments with T. ferrooxidans (Yang et al, 2001; Zhou et al, 2000; Zhou et al, 2001; Wei et al, 2001) for an enhanced restraint to pyrite. The results showed that the T. ferrooxidans after being cultured works the best in restraining pyrite. After 10 min pretreatment, the removal rate of pyrite from coal is up to 80%~90%. The research results by Yuan Xin et al (Yuan et al, 2000) show that T. ferrooxidans can restrain effectively the floatability of pyrite and can reduce the recovery of pyrite from 95% to 8%. Though the restraining properties of T. ferrooxidans to pyrite have been proved by many tests and experiments, there are very limited reports on its restraining mechanism. Thus, a systematic experimental research is carried out in this paper.

Jan 1, 2003

By D. Chakraborty, Neeraj Kumar

"The study provides the comparative analysis of the performance of water only cyclones and hydrocyclone for iron ore fines processing at Joda Iron ore processing plant, Tata Steel. Joda iron ore deposits have higher proportion of kaolinite in the finer fractions and are meant to be separated with cyclones. The iron processing flowsheet of Joda comprises of water only cyclone for beneficiation of iron ore fines. Water only cyclones are used for the beneficiation of fines in the iron ore processing industry and have a larger cone angle compared to that of conventional hydrocyclones to enhance the density effect in the separation. They are aimed to achieve better product quality of underflow however; the desired result could not be achieved at the Joda processing plant. The water only cyclones were operating at the corrected cut-size of about 60 micron with an imperfection of 0.40 and water split to underflow was approximately 10%. The overall Fe recovery from the water only cyclones were 60%. Since the quality of fines produced from the water only cyclone couldn’t be improved, an attempt was made to process the fraction in the conventional hydrocyclone to achieve the desired product quality. The trial results indicated better product quality with the Fe recovery of 72% at corrected cut-size of 70 microns and imperfection of around 0.29. In view of above results it was recommended to replace the water only cyclones with hydrocyclones to achieve higher product quality of about 60% Fe content.INTRODUCTION Water only cyclones were installed at wet plant, Joda to process the classifier fines where the cyclone underflow is considered as concentrate and overflow is discarded as slime. Because of the lower capacity of the cyclones 30% of the classifier overflow was bypassed directly to thickener. Apart from this the quality of fines produced from the water only cyclone couldn’t be improved further hence an attempt was made to process the fraction in the conventional hydrocyclone to achieve the desired product quality and quantity. Hydrocyclone was installed at Joda after replacing stub-cyclone and came into operation on 23rd Aug’ 2017.The process variables of water only cyclones and hydrocyclones are tabulated below:"

Jan 1, 2018

By Arkady Senchenko

The paper deals with the problem of refractory gold-containing material processing. It is observed that all traditional methods for liberation of fine gold from this type of products are characterized by a number of essential disadvantages, where the main ones are ? considerable expenses for ore processing and big environmental impact. As an alternative to the existing methods there is considered a gold liberation method, which is based on the combination of ultra fine grinding process with the consequent atmospheric oxidation. The theoretical justification of atmospheric oxidation was carried out, in the result of this the mechanism and the degree of sulphide minerals? oxidation was found out, the dependence of gold dissolution speed on the slurry content in liquid phase produced by grinding and oxidation was identified. The experimental data and results of pilot-plant testing are given and the most effective grinding and atmospheric oxidation mode is selected on this basis. The performed complex of research works allowed us to use the provided technology at the gold processing plant having capacity of 8 mln. tons of ore per year. The questions, problems, advantages and disadvantages of atmospheric oxidation technology for refractory gold-containing concentrates are considered in this paper. Keywords: refractory gold-containing material processing, gold liberation method, cyanidation

Sep 1, 2012

By Sergey Gudkov, Yuri Yemelianov, Stanislav Balikov, Andrey Boldyrev, Andrey Bogorodsky

"The results of POX of refractory gold-bearing concentrates using halide-ion as a lixiviant for precious metals and activated carbon as an adsorbent are given. It was found that gold did not recover to the solution when halide was added during POX. Silver partially dissolved in the solution. When halide-based reagents and activated carbon were added during POX, gold dissolved and loaded onto the activated carbon. The degree of sulfides oxidation was 99.3-99.6%. The recovery of gold onto granulated carbon was 94.7-94.8% when using chlorine-bearing lixiviants: NaCL, CaCL and carnalite and 98-99% when using KJ and KBr. This treatment process of refractory gold-bearing concentrates combines sulfide oxidation, dissolution and adsorption of precious metals. The results of the metals recovery achieved using this process can be compared with the recovery during POX-cyanidation. In this case, sodium cyanide was not used. This allows the reduction of capital and operational costs due to the absence of cyanidation, CIL and detoxification of leaching tailings circuits."

Jan 1, 2014

By João Queiroz, Cristian Marquez-Sarmiento, Luiz Teixeira

The removal of various metals from process waters and effluents is usually done by precipitation of the corresponding hydroxide. Manganese however is one metal that does not respond efficiently to that approach. It may be seen in its eH X pH diagram that the way of oxidation to Mn IV rather than hydrolytic precipitation of the Mn II ion as its hydroxide, is the way to efficient precipitation of Mn in the pH range 6 to 10. We studied the use of oxidants O2; NaClO; H2O2; Caro´s Acid (H2SO5) and the combinations of O2 or H2O2 with Na2S2O5, and H2O2 with NaClO, for the oxidative precipitation of Mn from synthetic solutions starting with 10 mg/L Mn, at 25 oC. In adequate conditions, which include pH > 8, it is possible to reach final [Mn] less than 0.1 mg/L in 60 minutes of reaction time.

Jan 1, 2014

By V. Sovmen

The gold-ore Olympiada deposit is located within the Yenissei range (Krasnoyarsk Region, Russia). Primary sulphides ores are metasomatic changed rocks, mica-calcite-quartz structure with impurity amphiboles, chlorites, carbon, the rare thin grains of sulfides (up to 3%~5%) and native gold. The structures of ores are fine-grained, prevailing texture of ores - interspersed, vein-interspersed, band-interspersed, veinlet. The most important minerals in the deposit are: gold, arsenopyrite, pyrrhotite, antimonite, Sb-sulphosalt, quartz, muscovite, calcite, siderite, titanium minerals, chlorite and minor sulfides like chalcopyrite, galena, sphalerite, etc. A common problem in mineralogical studies applied to mineral processing (concentration, cyanidation, etc.) is the characterization of gold in ores and technological products. This paper discusses the behavior of minerals during technological process at operating factory in Olympiada Mine and gold distribution in the ores and products. For the mineralogical characterization of minerals ? combination of analytical techniques was used. Gold is encountered in the primary ores as free grains among rocks, growth with sulfides and nonmetallic minerals, inclusions in sulfides, sulphosalt, and nonmetallic minerals. The gold-sulphide ores of Olympiada deposit can be quite complicated for enrichment. With the purpose to increase the extraction of metal from concentrates by liberating the dispersed gold, forming inclusions in sul-fides, there is used technology of biooxidation of flotation concentrates in Olympiada Mine. Gold and the basic ore-forming minerals in the ores feed, sulphidic concentrates, biocakes, tailings of concentrates of flotation and products of hydrometallurgical leaching have been studied in the mineralogical research. During researches it is established that pyrrhotite was completely oxidized while arsenopyrite was oxidized almost completely in the bacterial oxidation process. Pyrite and antimony minerals behave similarly and were oxidized only partially. The main oxyhydroxides in the bacterial oxida-tion process are goethite, limonite and jarosite. The results of mineralogical researches showed reasons of losses of gold during hydrometallurgical enrichment.

Jan 1, 2014

By Vladko Panayotov, Marinela Panayotova

"Recently, in order to extract metals, the industry is trying to process old metallurgical slag. The material requires very fine grinding that results in enhanced slime-formation. This in turn leads to problems in the course of the flotation process and to a loss of metal. In addition, it causes difficulties in the wastewater treatment aimed at water reuse. The aggregation and separation of the fine particles and their further subjecting to mineral processing would result in more efficient use of raw materials. Closing the water cycle also would be facilitated. The paper presents results from studying sixteen flocculation reagents, commercially available for treating municipal wastewater, including products based on nanotechnology, for their ability to rend the production wastewater in suitable for reuse in the flotation. It turned out that, from all studied reagents, the cationic C-587 is suitable for the purpose. Some of reagents were studied for their ability to flocculate selectively, in presence of coke fines, rich in copper fines which are produced at grinding of a slag from lead-zinc metallurgy. Most promising reagents are chosen, based on the chemical analysis of the flocculated materials. Open-cycle rough copper flotation experiments with the flocculated fines and recycled wastewater gave encouraging results."

Jan 1, 2014

By Mohammad Mainul Hoque, Linhan Ge, Ai Wang, Geoffrey Evans, Subhasish Mitra

"Dispersed phase interactions involving bubbles and particles in the turbulent environment play a significant role in the flotation process. The conventional collision models only account for the deterministic rather than the stochastic behavior of turbulenct flow. What the bubble-particle collisions would be like remains an open problem due to the complex nature of turbulent flow. To address this research question, the present study aims to quantify the bubble-particle collision efficiency incorporating turbulence using the computational method. Multiple solid particles were released to interact with a single stationary rigid bubble (non-deformable interface). Effect of particles Stokes number, turbulent intensity (TI) and integral length scale on the bubble-particle collision efficiency (Pc) was examined. Large Eddy Simulation method (LES) was used to compute the continuous phase. Fluctuating velocity required at the inlet boundary condition was derived from Gaussian energy spectrum to generate the upstream turbulence. Discrete Phase Model (DPM) is used to simulate particle trajectory. The characteristics of turbulent flow were analyzed through Energy spectrum and energy dissipation rate. The critical initial releasing radius of the annulus, where Pc equals zero, reaches up to 1.5(Rb+Rp) under high turbulent intensity (TI) 20.48% compared to 0.23(Rb+Rp) calculated from the traditional Pc model. Pc decreases as the distance of initial releasing annulus between bubble centre increases. Pc increases as particle Stokes number increase up to 0.66. The collision efficiency for particles of St less than 0.38 is higher under TI 11.78% compared to TI 4%.INTRODUCTION To increase mineral recovery, interactions between bubbles and particles are essential. All flotation devices achieve it through introducing some level of turbulence into the system by increasing specific energy dissipation rate. Figure 1 shows three different flotation equipment, traditional floatation cell, Concorde cell and cyclonic-static micro-bubble flotation column (FCSMC), with different turbulence generation mechanisms – impeller, down-flow liquid jet and pump recirculation, respectively."

Jan 1, 2018

By Sonia Helle, Ursula E. D. Kelm

"From a metallurgical point of view, acid leaching of oxide zone copper ore is considered in the first place in terms of ore grade, whole rock mineralogy, rock granulometry, crushed aggregate size distribution, porosity, permeability and corresponding fluid flow characteristics. Despite exhaustive physicochemical and general mineralogical characterization, drops in copper recovery occur and are often attributed to and “unquantified mineralogical misbehaviour” of the gangue phases. This study establishes an experimental link to monitor and quantify the chemical interaction of chrysocolla, malachite and atacamite with reactive gangue phases.Laboratory-scale sulphuric acid (15%) leaching in small columns is carried out using a synthetic rock composed of 57% quartz, 1% ore phase, and 42% reactive gangue. Gangue phases were selected to represent mineralogy found in argillic, advanced argillic, and propylitic alteration zones. Exotic copper ores of Codelco Norte (in particular Mina Sur) served as model for the modal distribution of mineral phases. Natural reactive gangue phases (<200 Tyler mesh) were chosen as pure as possible: Saz-1 and Swy-1 montmorillonites, KGa-1B and KGa-2 kaolinites (all Clay Mineral Society, USA, Source Clays) Nau-2 nontronite, Imt-1 illite (both Clay Mineral Society Special Clays) and Chilean mordenite, laumontite and bentonite. Ore phases are: mineraloid chrysocolla from Radomiro Tomic (Codelco Norte), reagent grade malachite and a purpose synthesized atacamite-paratacamite mixture. Complete chemical, physicochemical and mineralogical characterizations were carried out for ore and gangue phases.The following observations hold for samples with and without mineralization: Smectite-rich gangue increased up to 75% in volume. Once wet, air-filled vesicles formed due to the rapid sealing effect of overlying smectite in the column. No volume change occurred for illite, mordenite and kaolinite gangues. For kaolinite mixtures acid puddles formed on top of the column during initial leaching due to the delamination and barrier formation of this phyllosilicate. Fluid recovery was <60% for expandable phases and reached up to 80% for non-expandable mixtures. These observations confirm the very low extractions obtained in ore with a combined smectite – kaolinite gangue for Mina Sur. The most important mineralogical changes observed in the solid residues are: reduction of basal smectite phase reflections (XRD), and slight loss of illite intensities. This is also reflected in the major element composition of the residues, which demonstrate a loss of Mg, Mn, Ca, Na, K followed by Fe, Al and Si; with their proportions depending on the starting materials. Furthermore, alunogen and meta-alunogen formed, with related phases coquimbite (illite) and godichite (nontronite) also depending on gangue mineral chemistry. For laumontite samples, meta-alunogen and alunogen precipitated from the leachate."

Jan 1, 2003

By C. Çelik

Nowadays the optical sorting of industrial minerals is one of the most important processing methods which has cost efficient production possibilities. This method is used for industrial and raw materials that have different colour and brightness features. Initially this technology is used for sorting of foodstuffs and recovered glass, but for a long time also as physical mineral processing method for both industrial minerals like: limestone, marble, talc, basalt, flint, quartz and secondary raw materials like: building rubble, refractory materials, glass, plastic and household waste. In this study via optical sorting the separation of quartz out of a flint mix, which consists of the particles with different colors and brightness, is aimed. Experiments are performed on an optical sorting machine named CombiSense® 1200 at the institute of ?Aufbereitung mineralischer Rohs-toffe? RWTH Aachen. This automatic picking device was developed by the company ?Separation Systems Engineering (SSE), Wedel?. Hand picking method is used for product analysis and the efficiency tables are prepared on every step accordingly. This process enables to reach quartz products with purity up to 100%.

Jan 1, 2014

By A. S. Broesder

"With depletion of global ore deposits, there has been an increasing industry trend towards mining of lower average grade deposits in order to meet global demand, resulting in increased processing cost, energy usage and water usage. Consequently the industry is seeking pre-concentration technologies to reduce costs, increase production in existing operations and potentially enable the economic mining of previously uneconomical deposits. This pre-concentration can also advantage downstream processing and metal recovery. CSIRO has developed a large scale magnetic resonance based technology for the rapid quantitative detection of selected copper, iron and arsenic minerals in bulk ore. The technology is suited to measurement on large primary conveyors for enabling “pod” based sorting. The approach used in high tonnage sorting is to not sense and divert individual rocks, but to instead measure groups of rocks (“pods”) carried continuously on a single primary conveyor that can be diverted by conventional mechanical means. Bulk ore sorting operates by removing barren ore pods from a stream of crushed ore based on a bulk sensor measurement at a pod resolution of ~1 – 10 tonnes. The sorting process is based on the intrinsic variability of grade during the mining process that often occurs at the few tonne scale, and for instance, is common in many porphyry copper deposits. The MR technology has been proven in the laboratory for a wide range of copper, arsenic and iron minerals. A full scale prototype sensing system has been demonstrated in a trial at an Australian copper mine. Implementation trials of commercial MR based bulk sorting systems are progressing during 2018.INTRODUCTION An increasing trend in the mining industry is the exploitation of larger lower-grade deposits to meet global demand. Low-grade deposits involve increased processing cost, energy and water usage and increased tailings. There is therefore growing interest in technologies that enable more efficient extraction of low grade deposits. Water intensity of mining activities in a context of water scarcity, and the environmental and health implications of mine tailings are existing challenges, which are only made worse by the progression to lower grade orebodies. There is therefore also an interest in safer, cleaner and less wasteful extraction and production to ensure community well-being and environmental resilience."

Jan 1, 2018

By Roberto C. G. Oliveira, Scott C. Brown, Brij M. Moudgil

The wettability or surface energy of particle surfaces dictates a number of multiphase ensemble interactions that have a significant impact in mineral processing. Dispersion, bulk powder handling and flotation behavior are just a few of the parameters that are largely due to the degree of hydrophillicity or hydrophobicity on particulate surfaces. Because of the inherent impact of surface wettability in nearly all industries, fields, and multi-phase interactions, a number of simple, precise and accurate techniques for accessing surface wettability or contact angle on macroscopic flat surfaces have been developed. However, these techniques cannot be directly applied to the particulate surfaces that are often in query. Though a number of techniques are available for accessing the wettability of particulate surfaces, these methods are either relative, application specific or prohibitively tedious. In this study, key features of existing techniques are combined to formulate an improved method to delineate particle wettability that is simple, versatile and capable of providing reproducible measurements in an industrial environment.

Jan 1, 2003

By M. M. Fan

In Florida?s phosphate industrial practice, the most favorable upper size limit of froth flotation is 1.18 mm which corresponds to particle weight of about 2.8 mg. Conventional froth flotation is not efficient in upgrading coarse particles (+0.425-1.18 mm). A limited number of studies have been devoted to understanding and improving coarse particle flotation. We have shown that the coarse particle flotation performance can be significantly improved by the presence of picobubbles generated by hydrodynamic cavitation. In this study, the size of picobubbles produced under certain hydrodynamic conditions was measured by a laser particle size analyzer. A size-by-size flotation performance analysis of coarse phosphate froth flotation in the presence of picobubbles is conducted in terms of flotation kinetics, selectivity and recovery. It was found that picobubbles doubled the flota-tion rate, increased the P2O5 recovery more significantly for +0.85-1.18 mm particles than +0.425- 0.6 mm and +0.60-0.85 mm particles. At a given acid insolubles (A.I.) rejection, the presence of picobubbles increased the P2O5 recovery by up to about 25%.

Jan 1, 2014

By Yizhong Yuan, Dao Li, Nannan Xue, Tao Liu, Yimin Zhang

A new multi-stage counter-current circulation leaching process for extracting vanadium from stone coal was proposed, and the main factors on multi-stage counter-current circulation acid leaching process were investigated. The results show that the vanadium recovery could reach 86% under the conditions of sulfuric acid concentration of 4 M, liquid to solid ratio of 2 mL/g, temperature of 95 °C, reaction time of 60 min, mean particle size of 125 µm and circulation acid leaching stage of three. The losses of vanadium in acid leaching solution appeared during the four-stage acid leaching process. The strong adsorption performance of new formed KAl(SO4)2(H2O)12 crystal was main reason.

Jan 1, 2014