Search Documents

By D. J. Scarratt

Fisheries make a significant regional contribution to the economy of Canada. In the Atlantic Region, over 70 thousand workers depend on the primary or secondary fishing industry. Fisheries are vulnerable to pre-emption of space by other marine industries and to contamination by chemical discharges. Markets may be affected even by the threat that products may be tainted. Fish may be killed by drags and dredges, and their physiology and behaviour affected by suspended sediments are stirred up by mechanical devices. Virtually no evidence exists of adverse impacts £ran ocean mining on fisheries, but projections from other marine activities such as fishing itself, dredging and other marine discharges give reason for caution. Department of Fisheries and Oceans policy calls for review of ocean mining proposals to ensure adequate protection of fish stocks, fishing activities and fish habitat, and compensation for losses attributable to any industrial project. Adverse impacts can be minimized by careful attention to details of location, technology and timing, and to close co-operation and information exchange between industry and the regulatory agencies.

Jan 1, 1985

By S. Naidu, J. Kelley, Roger Amato

The Alaskan Continental Shelf covers 76 % of the total shelf area of the United States. There are a lot of potential gravel deposits in the Alaskan offshore region. The gravel resources are currently not feasible for mining for the following reasons (U.S Congress, 1987): 1. Much of the glacial gravel is poorly sorted. 2. Gravel deposits are overlain by sandy and muddy layers. With the sea level expected to rise 70 cm in the next 100 years (Intergovernmental Panel on Climate Change, IPCC, 2001; Day, 2004), erosion of coastlines will be a major problem not only in Alaska but worldwide. Hence beach nourishment projects designed to minimize erosion will require large volumes of sand and gravel. Offshore areas will become a logical source for the fill material because of their proximity and ready availability. It is likely that future supply of coarse aggregate in Alaska may involve exploitation of marine deposits. The Chukchi Sea is a potentially favorable region for this type of mining because of extensive deposits of paleo beach and other relict gravel found in the near shore region (Stauffer, 1987). However a systematic analysis of potential gravel resource has not yet been conducted and it is the purpose of this research to estimate the size, extent and variability of gravel material that may be available in the continental shelf, offshore Kivalina.

By In Kwon Um

The XRF Core-Scanner system performs non-destructive analysis of elements from Mg to U, in concentrations of ppm levels on split cores with digital images. Using the AVAATECH XRF Corescanner system, we conducted high resolution element analysis of deep sea sediment cores from Clarion-Clipperton fracture zone of the northeastern Pacific to reveal recent environmental changes. Comparison of data estimated by the XRF core scanner with ICP-AES showed relatively weak correlation coefficients except Mn contents. Down-core variations of most elements seem to be matched with each other and reflect changes of sediment colors. Especially Mn/Al ratio significantly change at distinct color boundaries. The variations of Mn/Al ratio with sediment colors are suggestive of changes in redox condition and further divided into two types probably affected by activities of benthic organisms. Be isotope age datings of select core (BC08-02-13) indicate that the color boundaries are approximately coincident with late Pliocene and Pleostocene also early Pliocene and late Pliocene boundary. Keywords: XRF core scanner, High resolution, C-C zone

Jan 1, 2011

By W. H. Pelton

Polymetallic sulphide (PMS) deposits have recently been discovered associated with hydrothermal vents on the sea floor off Vancouver Island, B.C. Visual estimates indicate reserves in excess of 1 million tons. Reliable reserve estimates have not yet been made, however, due to the extreme difficulty of drilling cores in 2 km of water. Few geophysical techniques can aid in the exploration of these deposits. There is little or no difference in radioactivity, magnetic susceptibility or electrical resistivity between the deposits and the surrounding sea floor sediments. This precludes radiometric, magnetic, electromagnetic and resistivity methods. There is a density contrast, but the logistics of gravity surveys at such depths are formidable. The physical property which shows the most contrast with the sea floor sediments, and which is perhaps one of the easiest to measure (with modern equipment) is polarizability. The induced polarization (IP) method is one of the major electrical geophysical techniques for exploring for PMS deposits on land.

Jan 1, 1985

By J. R. Hein

East Diamante is a submarine volcano in the southern Mariana arc that is a complex caldera about 10 km x 5 km (elongated ENE-WSW), and breached on its northern and southwestern sectors. A large field of barite-sulfide mounds was discovered in June 2009 and revisited in July 2010 aboard the R.V. Natsushima using the Hyper-dolphin ROV. The mound field occurs on the NE flank of a cluster of resurgent domes inside the caldera. The mound field extends for more than 100 m long and is about 30 m wide, and is aligned along a NE-SW rift valley. A sample of dacite yielded a 40Ar/39Ar age of 20,000±400 years. Individual mounds are typically 1-3 m tall and 0.5-2 m wide, with lengths from about 3 to more than 5 m. The mounds are composed of barite-dominant layers interbedded with Zn-sulfide-rich barite layers. Rare inactive spires and chimneys cap some mounds. Fe and Mn oxides are currently forming small (<1 m diameter, ~0.5 m tall) subsidiary mounds on the top of some of the sulfate/sulfide mounds and drape the flanks of others. Both diffuse- and focused-flow fluids emanate from the subsidiary oxide mounds. Ages of the basal sulfate/sulfide mounds cluster around 4,000 years old based on 226Ba/Ba, whereas the oxides are less than 5 years old based on 228Th/228Ra. Most mound and chimney samples are dominated by barite and amorphous silica; sulfides occur in variable amounts that in decreasing order of abundance include sphalerite, galena, pyrite, and chalcopyrite. Anglesite, cerrusite, and a Pb phosphate occur as late-stage interstitial phases. Some mound samples have fragmental textures; layered clasts composed of chalcopyrite and pyrite may have been derived from collapsed chimneys. Despite the abundance of barite, samples contain high concentrations of Zn (to 23 Wt.%), Pb (to 13 wt.%), Ag (to 500 ppm), and Au (to 15 ppm). Copper is enriched in a few mounds samples, up to 3 wt.%, but is typically <1 wt.%. Other significant metal enrichments include Sb (to 1320 ppm), Cd (to 1180 ppm), and Hg (to 55 ppm).

Jan 1, 2011

By Patrick J. C. Ryall

Remotely control led drills capable of being lowered to the sea-floor from ordinary research vessels have been developed over the past two decades. These drills are currently being used in geological survey programmes on the continental shelves (Canada, Japan, Norway, United Kingdom) and for studies of mid-ocean ridges. Generally the drills fall into two categories: 1) those which are powered from the surface and controlled by an operator, and 2) those which are battery powered and follow an automatic programme. Some drills have a television camera mounted on them sending a picture to the surface as an aid to site selection and geological interpretation. Typically the drills are capable of drilling a core 2.5 - 5 cm diameter up to 10 m long. While most of these drills are designed for <1000 m depth, some can drill in water depths of as much as 3500 m.

Jan 1, 1985

By Tetsuo Yamazaki

Deep-sea rare-earth element-rich mud (REE Mud) distributes in pelagic clayey sediment column on ocean seafloor at 4,000-6,000 m deep. The thickness ranges 5-80 m and the burial depth 0-100 m. The REE content ranges 600-2,250 ppm in Pacific and one of the richest, maximum 6,500ppm, has been found in Marcus Is. exclusive economic zone. By applying a conventional hydraulic excavation and lifting methods, the economy of REE Mud mining around Marcus Is. is preliminary examined. Because the waste content in REE Mud is high and the disposal cost in Japan is very expensive, the mining is recognized far away from economy.

Sep 14, 2011

By H. Shimoda, K. Tamaki, K. Iizasa, M. Watanabe, K. Okamura

Modern Kuroko-type deposits occur in submarine calderas of island-arc fronts and back-arc rifts in Japan. They occur primarily on or adjacent to caldera boundary faults. Hydrothermal sulfides in the Myojinsho submarine caldera are one of Kuroko-type deposits, but their occurrence is different from other deposits found within the area 200 km2 around the Quaternary volcanic front of Izu-Ogasawara arc.

Aug 24, 2006

By Charles L. Morgan

The Minerals Management Service of the U.S. Department of the Interior and the State of Hawaii Department of Planning and Economic Development are investigating the cobalt-rich ferromanganese oxide crust deposits found within the Exclusive Economic Zones (EEZ) of the Hawaiian Islands and Johnston Atoll. The objective of this investigation is to complete a preliminary resource assessment and an Environmental Impact Statement for potential leasing of mineral rights to these crusts. The results of this effort will be summarized and published in a Draft Environmental Impact Statement in March 1986. Three oceanographic cruises to deposit sites in the Hawaiian Islands EEZ were conducted by the University of Hawaii in 1984. As a result, data and sample analysis yielded the following resource estimates (in thousand tonnes): (1) total crusts - 378,500; (2) cobalt - 2,500; (3) manganese - 76,200; (4) iron - 59,700; and (5) nickel - 1,400. These estimates do not include key factors such as deposit continuity, recoverability, and environmental sensitivity. A preliminary attempt to quantify some of these factors for one particular deposit is in progress and will consist of detailed field studies followed by laboratory analysis. Similar evaluations of the Johnston Island EEZ have also begun and are based upon field work conducted by West German researchers and the U.S. Geological Survey. The Johnston Island EEZ appears to have crust resources about as large as those contained in the entire Hawaiian EEZ.

Jan 1, 1985

By Peter M. Bartlett

The Republic of South Africa ranks among the world leaders in both reserves and production of numerous land-based mineral commodities. Over the last three decades, however, South Africa has also identified several commodities that may exist in commercial quantities in the marine environment. The major targets include 1) placer diamonds; 2) titanium- and zirconium-rich beach sands; 3) sedimentary and concretionary phosphorite and glauconite deposits; 4) manganese nodules; and 5) hydrocarbons. South Africa ranks second in world reserves of diamonds and has potentially enormous sea resources. Diamonds are currently recovered on the Atlantic side from ancient beach gravels in the Northwest Cape Province and from the seabed south of the Orange River to Lamberts Bay. Approximately 100,000 carats (or just 1% of South Africa&apos;s total annual production) are produced each year from offshore operations. DeBeers is investing approximately $5 million per year on sea prospecting activities and currently operates three vessels in offshore recovery operations. Diamonds recovered at sea will remain a small percentage of total production because of huge land-based reserves that are mined at a fraction of the cost of seabed operations.

Jan 1, 1986

By Steven D. Scott

Stephen D. Scott Steven Scott is a Professor of Geology, Director of the Marine Geology Research Laboratory and, until May 1997, was Chairman for 9 years of Geological and Mining Engineering, all at the University of Toronto. Steve also holds a cross appointment at the University of Western Brittany&apos;s European University Institute of the Sea in Brest, France. He was educated at the University of Western Ontario (B.Sc. and M.Sc.) and at Penn State (Ph.D.). Steve is a geologist/oceanographer specializing in base and precious metal massive sulfide deposits which he and his students have studied on five continents and on the bottom of three oceans. He was the first ore deposits geologist and first Canadian to witness "black smokers" on the ocean floor. Since 1982, he has participated on 21 oceanographic surface and submersible expeditions, many of them as Chief Scientist. His research team is currently carrying out projects in the W and NE Pacific Ocean. Steve has published more than 150 research papers and lectured in more than a dozen counties. Popularized accounts of his work have appeared in various media.. He has been honored by several awards and distinguished lectureships. Steve is President of the Canadian Scientific Submersible Facility, which operates the Canadian ROPOS robotic submersible, and is President of the International Marine Minerals Society.

Jan 1, 1998

By Robert G. Ditchburn

Dating seafloor mineralization at hydrothermal centres of submarine arc volcanoes is important for understanding deep-seated volcanic events that can produce deposits rich in base and precious metals. The activity ratios, 228Th/228Ra, 228Ra/226Ra (Bq.Bq-1) and 226Ra/Ba values (Bq.g-1) are used for dating barite- rich seafloor massive sulphide (SMS) in the age ranges 0.3 ? 12 years, 3 ? 35 years and 500 ? 15,000 years, respectively. Thus, the time elapsed to amass an economic deposit and, ultimately, its capacity for sustainable extraction, can be estimated. 226Ra/Ba and 228Ra/226Ra values have been measured in relatively young chimneys that were collected, 1998 to 2006, from hydrothermal sites at Brothers and Clark volcanoes (Kermadec arc) and East Diamante volcano (Mariana arc) to check these initial ratios, essential for calculating ages for older mineralization at the same sites, were not varying significantly. We found that the 226Ra/Ba value for fresh SMS mineralization at the Brothers NW caldera and East Diamante hydrothermal sites have been reasonably stable for 6 years and 2 years, respectively. At both sites, the 228Ra/226Ra value for fresh SMS has been stable for 5 years. This was established from young chimneys where the measured 228Ra/226Ra value could be corrected for radioactive decay using the age derived via the 228Th/228Ra method. However, long-term stability of the initial 226Ra/Ba and 228Ra/226Ra values has yet to be proven. These isotopes of Ra are used as a proxy for better understanding of the transfer of Ba from deep magmas to the seafloor, via the circulating fluids of the hydrothermal system.

Jan 1, 2011

By I. V. Kubrakova, O. A. Tyutyunnik, M. L. Getsina, A. M. Asavin

An analysis of noble metals (NM) in natural samples is most problematic. Determination of their traces in geochemical samples, in part, for the purpose of deposit evaluation, is a difficult analytical task. A number of international standard reference materials of rocks and ores, in which NM content is certified, is estimated at a half dozen. For example, in the International proficiency test for analytical geochemistry laboratories (GeoPT), which is held by the Department of Earth Sciences (The Open University, United Kingdom), the data for gold and platinum are observed very rarely, and the results obtained in different laboratories differ on 1-3 orders of magnitude. It is caused by low contents of NM in nature, by a variety of their complex and mineral species, as well as by a complicated matrix composition of platinum-containing objects. Among these objects are ferromanganese ores, enriched strongly with Fe, Mn, Ni, REEs - the elements hampering a precise determination of NM due to a complexity of instrumental inter-element correction. The absence of the reliable methods of NM determination in these ores drastically limits the possibility of deposit evaluation.

By Michael J. Cruickshank

Marine minerals are more than an academic curiosity as they represent the most significant global source of mineral materials for economically and ecologically sustainable development for the future. Minerals research is traditionally carried out by industry and thus, in the United States at least, applied research in marine minerals may not get the share of government funding or attention that more exotic programs for space exploration or future global disasters engender. Two recent events have significantly changed the status of marine minerals. Discoveries made in the last thirty five years indicate that the potential for mineral occurrences in the oceans and seabeds, area for area, is as high as for terrestrial lands. On this basis the global mineral resource base has been recently increased by a factor of four of which three quarters is underwater. The recently enacted Law of the Sea has mandated what is probably the most far reaching re-distribution of natural resources in human history, and has resulted in a peaceful subdivision of seabed jurisdictions between the coastal nations of the world which should significantly affect future mineral markets and the balance of economic powers. Significant applied research efforts are ongoing for marine minerals as an adjunct to commercial production in southern Africa for diamonds; and in many other parts of the world for sands for beach and coastal protection. Forward planing, including research and development activities focussed on future commercial production of metalliferous oxides, continues in Korea, China, Japan, India, and with lesser activity, in the United States, United Kingdom, Germany and the CIS. Annual expenditures for this work amount to millions of dollars. In all cases the environmental aspects of commercial produc¬tion are a significant part of the research. Geologic studies on the occurence and distribution of metal sulfides at plate boundaries continue on a regional basis in the Pacific.

Jan 1, 1996

By Cees van Rhee, Rudy Helmons

INTRODUCTION Seafloor Massive Sulphides are typically found near the oceanic ridges at larger water depths (>1km). The physical properties of SMS, as shown in table 1, are comparable to the properties of weak rock. One of the technical challenges to enable extraction from these locations is the cutting or excavation process. Experiments have shown that the energy needed to excavate the material may increase with water depth (Alvarez Grima et al. 2015). Besides that, it is demonstrated that rock that fails brittle in atmospheric conditions can fail more or less in a plastic fashion when present in a high pressure environment, as would be the case at large water depths. The goal of this research is to identify the physics of the cutting process and to develop this into a model in which the effect of hydrostatic and pore pressures is included. The cutting of rock is initiated by pressing a tool into the rock. As a result, at the tip of the tool a high compressive pressure occurs, which leads to the formation of a crushed zone. Depending on the shape of the tool and the cutting depth, shear failures might emanate from the crushed zone, which will eventually expand as tensile fractures that can reach to the free rock surface. Through this process intact rock will be disintegrated to a granular medium. For an overview of the process (figure 1). Additionally, the presence of water in the pores of and surrounding the rock influences the cutting process through drainage effects. The most relevant effects are weakening when compaction and strengthening when dilation occurs in shearing and tension. Deformation of the rock causes the pore volume to change, resulting in a under or over pressure. As a result, the pore fluid needs to flow. The magnitude of the potential under pressure is limited through cavitation of the pore fluid, limiting further reduction of the pore pressure (figure 2). The drainage effects cause the rock cutting process in a submerged environment to show a stronger dependency of both the hydrostatic pressure as well as the deformation rate (figure 3).

Jan 1, 2018

By Ivo Dreiseitl

The interaction between nodule harvester and eupelagic sediment on the seabed is definitely one of the key aspects of mining technology for polymetallic nodules which is to be studied in details. Physical properties of sediments play major role for evaluation of protection and preservation of marine environment while strength properties of sediments will come in useful for future mining operations. Cone penetration test (CPT) used for testing in situ is one of methods for investigation strength properties of sediments. The testing apparatus for CPT consists of an instrumented cone having a tip facing down and it is mounted on special underwater equipment (rus. UGI-1). UGI-1 can determine subsurface strength down to the depth interval 0 ? 1.10 m. Special IOM geotechnical cruise was accomplished in 1989 on board R/V Academic A. Karpinski within the extra test area of about 1000 km2. Thanks to UGI-1 the IOM database recorded unique strength sediment data (cone penetration resistance) from 279 seabed points of sounding at profiles 125.6 km long. Up to 35 strength data from depth interval 0-1.1m (every 3cm) were obtained from any particular testing point. As a result 279 strength charts could be plotted (two examples in Figure 1). The cone penetration resistance values can be correlated to shear strength parameters.

Jan 1, 2011

By Tetsuo Yamazaki

Seafloor massive sulfides have been a subject of interest for profitable commercial mining these ten years. Because of the higher Au, Ag, and Cu contents, they have received much attention as immediate commercial mining targets by private companies and nations. Some of them already proposed the technologies necessary for the commercial mining. However, the technologies for survey, excavation, lifting, and ore dressing have not yet well been examined from viewpoint of the economy. In this presentation, the authors present some key factors and improvements for better economy in the mining.

Jan 1, 2010

By Daniel E. Walsh

The recovery of most minerals, which are amenable to gravity concentration, is standardly determined by accurate sampling and assaying. .With respect to particulate - gold ores, sampling and assaying are still the convention, but the accuracy and reproducibility of these operations are much discussed and debated points. Evaluation of gravity concentrators by conventional sampling and assaying techniques is very time consuming, costly and may introduce a large amount of uncertainty into the results due to the particulate nature of placer gold. These problems are not unique to placer gold ores and apply to any low grade ore with particulate values. A gravity concentrator evaluation process developed by MIRL employs the use of neutron activated gold (198Au) and radiation detection circuits which monitor the concentrator&apos;s product pulp streams. Concentrator recovery is determined from the ratio of the number of gold particles detected as passing into the concentrate to the total number of gold particles detected over all monitored pulp streams. This system eliminates the experimental errors introduced by sampling, sample reduction, and assaying and allows recovery to be evaluated for gold particles of specific sizes, shapes, and flatness. This system enjoys its greatest utility where a large number of tests are to be run in order to evaluate a concentrator over a variety of operational settings, i.e. factorial designs, and allows accurate testing of concentrators operated in closed circuit systems. Beginning in 1984, MIRL conducted radiotracer studies of unit processes, which included jigging, static wedge wire screening, elutriation, and concentration with compound water cyclones.

Jan 1, 1989

By Katherine H. Walton

The research affiliate projects of the Continental Shelf Division of the Marine Minerals Technology Center concentrate on the development of technologies and methodologies for the exploration 4 and assessment of nonfuel continental shelf mineral resources within the U.S. Exclusive Economic Zone. Three of the FY 1990-91 research grants are summarized below. Scientists at the Center for Applied Isotope Studies at the University of Georgia have developed ?An Advanced Design for a Seafloor Gamma Isotope Mapping System? for the rapid collection of data on seafloor sediments. This system is designed to detect gamma radiation emitted by naturally occurring radioactive elements found in marine sediments. This data can be used to study seafloor lithology and has direct application in marine mineral surveys. The purpose of this study has been to redesign and calibrate the system for marine mineral survey work. Recent modifications of the sled design, gamma radiation detector, and supporting software have resulted in considerable improvements in sensitivity, functional operation, and data acquisition.

Jan 1, 1991

By Valcana Stoyanova

Data and information for this study were collected in June-July 2009 onboard the RV Yuzhmorgeologiya in the area covers about 7000 km2 in the eastern part of the CCFZ between 10º05? - 10º55?N and 119º25? ? 121º08?W. In accordance with the IOM research program the cruise was intend to acquire both geological and environmental data and information necessary for delineation of nodule deposits and also data for identification of the baseline of benthic ecosystem. Having implementation of its 15-year plan of work for exploration under the contract with ISA, current activities of IOM were focused on nodule fields within prime areas that could be mined in the future. Bottom photographs obtained by towed deep-sea vehicle NEPTUN along 6 profiles with common length about 300 km (Fig. 1). In total, about 11,500 digital photographs (what cover approximately 40,000 m2 of the ocean floor) were analyzed for assessment of nodule coverage and investigation of megafauna (animals, visible in photographs, the dimension more than 2 cm). The giant single-cell organisms Xenophyophorida were the most multiple animals in seabed photographs. Their number on the site area averaged 1187 ind/ha. However, the vertical camera position does not allow counting all xenophyophorids, therefore their valid number is represented 10 times more. According to all available information these protozoans play the relevant role in assemblage of deep-water environment, giving for other animal groups an [ ] additional source of nutrition and a substratum for settlement and attachment. The ophiuroids are found in assemblage with xenophyophorids in many cases, standing on a sediment at their base.

Jan 1, 2010