Search Documents

By Michael McVay

The use of augered cast-in-place piles has seen tremendous growth under commerical structures in the past twenty years. Problems with vibration, soil densification and/or heave associated with driven piles do not occur with properly installed augered piles. Augered cast-in-place piles were originally constructed (1950s) with diameters of .31 m (12 in.) and lengths up to 6.1 m (20 ft); however with the advent of better drilling equipment, diameters varying from .41m(16 in.)to .61 m (24 in.) and typical depths ranging from 18.3 m (60 ft) to 24.4 m (80 ft) are achievable. Reinforcement may vary from a single high strength rebar (Grade 60) at the top of the pile to a continuous steel cage depending on loading (compression, tension-uplift, and lateral). Typical axial design loads (compression) for a single augered cast-in-place pile are in the 445 kN (50 tons) to 890 kN (100 tons) range.

Jan 1, 1997

The process of pile driving disturbs the soil around the pile. The nature and magnitude of disturbance depends upon 1) the pile size, and 2) the nature of soil. Therefore, the prediction of a single pile behavior based on soil properties of undisturbed soil samples may not match its performance. Under lateral loads, the pile may loose contact with the soil near the ground surface especially in clays. The soil pile interactions are influenced the most by pile behavior in this zone. This situation further affects the tally of prediction and performance. Piles are used in groups. The zones of overlapping stress from one pile to the other both around the pile and below their tip particularly in soft soils, contribute to group effects. Empirical solutions have been developed for prediction of the pile group behavior. The group action is more involved under vibrations. Several cases of single piles and pile groups under static and dynamic loads from published records have been analysed. It has been shown that single pile test is the best source of information on the soil-pile-soil interaction effects.

Jan 1, 1989

By Paul J. Axtell

This case history describes the foundation design and construction for the New Mississippi River Bridge, presently under construction in St. Louis, Missouri. The 1,500 ft (457.2 m) main span of the cable-stayed bridge is supported by two delta tower pylons in the river, with anchor piers on each bank. The final foundation design was completed as a part of an Alternate Technical Concept (ATC) proposal by the winning construction team, and utilized drilled shafts up to 11.5-ft (3.5-m) diameter that were socketed into very hard limestone. As part of the ATC foundation design, a full-scale, bi-directional static load test was performed to verify the design and allow use of higher resistance values. This paper presents the results of the site exploration, construction of the load test shaft, details of the load testing, and a comparison of the test results with various design parameters.

Jan 1, 2011

By N. V. Nayak

Maharashtra State Road Development Corporation Ltd., has initiated a scheme for construction of 55 flyovers in Mumbai in India. To ensure speedier completion of projects several new technologies were adopted to save time without compromising on safety and reliability. Many of the flyovers involved large diameter pile foundations carrying loads ranging from 3500kN to 1375kN. Significant time would have been lost in using conventional load testing procedure to check pile capacity apart from the difficulty in mobilizing the load and the obstruction to site movement and traffic on the adjoining roads. High Strain Dynamic Testing was introduced on the project sites in lieu of static load testing after conducting numerous co-relation studies on various project sites. A total of seven co-relation studies have been conducted till date and based on these data static testing has been replaced by dynamic testing on numerous flyovers. The paper presents the results of such studies. CAPWAP analysis was also conducted on the data to evaluate the percent skin friction and end bearing so as to improve future design parameters.

Jan 1, 2000

By David C. Kraft

Helical piles and ground anchors were used to meet critical design and constructability requirements for an urban forest Canopy Walk at the Atlanta Botanical Garden, Atlanta, GA. The 12-foot wide pedestrian walkway path was to be nestled among the treetops of a forest, extending to 600 ft. in length, and soaring 40 ft. high above the forest floor. Of particular concern during construction was that the foundation system for the temporary steel shoring system had to be non-invasive to the subsoil, could not damage the forest floor, trees, root systems, or foliage, and upon completion of the concrete walkway pour, could be removed, again without disturbing the subsoil. Accubrace, Inc. designed and installed all the helical foundation types, as well as provided steel braces, typically used in Tilt-Up building construction, for the walkway project. The braces, some extending to 43 ft. in length, were used to provide lateral support against wind loads for the walkway form. In addition, the braces acted as secondary support for lateral loads during the placement of wet concrete along the 600 ft. length of the walkway. Helical foundation products installed included vertical compression piles, ground anchors for tension rods, and ground anchors for the braces. The installation of the piles and anchors was particularly challenging since the forest floor elevation varied as much as 50 ft. due to the presence of a ravine. Information is provided on the subsoil conditions, required loads, design, installation, and acceptance criteria for each helical product type installed for the project. The results of vertical and lateral load tests on the helical piles in the pre-construction phase, conducted in conformance to project specifications are presented. Photographs to illustrate the nature and complexity of the project are included. The concrete pour for the walkway was successfully completed on December 12, 2009, and the walkway was opened for visitors in May, 2010.

Jan 1, 2011

By d&apos, E. Appolonia

A construction project is successful when all parties contributing to it are winners. It is not a success when there are winners and losers. Con­tractors, engineers, suppliers and equipment developers, and especially owners, each can contribute and benefit from a revaluation of attitudes and contacts from planning to final payment. The Deep Foundations Institute was initiated with this as its major purpose. The help of educators is essential to promote this with the next generation. The Association of Soils and Foundations Engineers has developed guides for "Mediation Arbi­tration of Construction Contracts."

Jan 1, 1985

By J. M. Pei

In this paper, the nonlinear finite element analysis is used to study the support system of a tunnel which is designed to pass through deep-embeded stratum. The rock mass is rather intact, though a section of tunnel will pass through the weak belt. Under the influence of the high ground stress, the condition of stability and the form of support become complicate. This paper, talcing into account the nonlinear properties of rock mass and the Interaction between rock, and support, makes a comparison between the two kinds of soft and rigid support systems, and analysed the changes of their bearing forces.

Jan 1, 2010

By Mazin Adnan

The 80m high dam at the Peribonka river in the Canadian province of Quebec was designed for the generation of 385 MW of hydro electrical power (Fig.1). The complex ground conditions required the employment of a variety of geotechnical construction methods stretched to limits never experienced before. Innovative grouting and trenching techniques were used for the construction of a plastic concrete cut-off wall down to a depth of about 116m, to cut hydraulic seepage through alluvial deposits forming the dam foundation. The bedrock where the cut-off wall is embedded forms a glacial gully with steeply sloped flanks, which created further challenging conditions. [ ]

Jan 1, 2008

By Seth L. Pearlman

Pin Piles are small diameter high capacity drilled and grouted piles also called minipiles or micropiles. They are ideal for building foundations on sites with poor ground conditions, sensitive surroundings, restricted vertical clearance, or difficult access. They are also well suited to foundation underpinning, arresting ground movements, and increasing the capacity of existing foundations. The major factors for selection of Pin Piles are reviewed; drilling, grouting, and design fundamentals are summarized; and a major case history is presented for the underpinning of the 43 story elevator core at the recently opened Mandalay Bay Resort and Casino in Las Vegas, NV.

Jan 1, 2000

By Michael Arnold, Jonathan Delgado

In 2017, Bauer Foundation Corp. (BFC) was awarded the contract to install the deep foundations for the new 17-story Hotel Tower and the Low Rise Casino Expansion at the Seminole Hard Rock Hotel and Casino in Tampa, Florida. The site was underlain by extremely challenging Florida Limestone geology and surrounded by occupied existing buildings and infrastructure. To overcome the challenges of the difficult subsurface conditions, and to successfully complete the foundation installation without impact to the surrounding buildings and casino operation, Langan Engineering (EOR) and BFC were required to modify both the design and installation techniques during construction. The scope of work included 147 temporarily cased drilled shafts to depths up to 230 ft (70 m) below ground surface (BGS), 76 permanently cased micropiles up to 200 ft (61 m) BGS, and more than 300 augered-cast-in-place (ACIP) piles up to 125 ft (38 m) BGS. Voids and zones of high permeability in the limestone created many challenges for execution of the foundation scope including ACIP piles overbreaks of more than 400% above neatline volume, and construction induced ground subsidence/collapses adjacent to structures supported on shallow foundations. This paper will discuss site limitations, design and construction challenges, difficult geology, varied soil conditions, and lessons learned. PROJECT The project is located at Seminole Hard Rock Hotel and Casino Tampa, Florida, as shown in Fig. 1. Seminole Tribe, the owner, started the construction of a new 17-story Hotel Tower and the Low-Rise Casino Expansion at the beginning of 2017.

Jan 1, 2018

By Jacob Chacko

The Izmit Bay bridge, a 3-km-long suspension bridge crossing of Izmit Bay, Turkey is planned to be constructed in one of the most seismically active places in the world. The site, which has the potential to experience significant earthquakes associated with the relative motion accommodated on the North Anatolian Fault, is underlain by deep deposits of soft soils, and areas of unstable and liquefiable soils. Characterizing the seismotectonic setting, foundation soil conditions, potential fault locations, as well as other geohazards was a critical component for the project concessionaire to finance the project and obtain meaningful bids for bridge design and construction. Given the Build Operate Transfer (BOT) funding mechanism, executing this work in the least possible time was critical to the concessionaire?s financing scheme. Fugro was retained to provide geotechnical, geological, and seismological evaluations for the project region, and to generate data for contractors to develop reliable designs and bids. The uncertainties in these data made it difficult for the BOT concessionaire to finance the project and tender Bridge design and construction. The investment in an early and comprehensive site characterization program to evaluate and quantify those uncertainties allowed the concessionaire to save schedule, provide a robust bid basis to bridge contractors, and persuade banks to finance what was perceived to be a relatively high risk project.

Jan 1, 2011

By H. W. Hunt

Accessories are increasingly used to protect and extend H, pipe, precast concrete, timber, and sheet piles for any soils conditions. With point protection, piles can be driven through boulders, layered rock, garbage dumps, and waterfront debris to provide dependable support for all types of structures. Splicers for pipe piles can be tapered for a water-tight drive-fit that does not require welding. The pipe splicer can be made applicable to precast concrete piles. Splicers for H make the long pile as strong as an unspliced length with only simple welding. Transition splicers quickly connect different types or sizes into efficient composite piles.

Jan 1, 2010

By Antonio A. Cristóvão, Alexandre Pinto

"Abstract Deep foundations of buildings using driven ductile iron micropiles TRIM solutions, leads to recognized advantages, from technical, schedule and economic points of view. High production rates together with the possibility of using conventional equipment, duly adapted, confer this solution a high versatility.The aim of this paper is to describe the main design criteria adopted for the foundations of the Church ""Nossa Senhora dos Navegantes"" building in Lisbon - Portugal. In addition, results of a full scale load test carried out at site are presented, confirming the adequacy of the solution to the geological and geotechnical scenario, which is characterized by the proximity of the Tagus River Basin as well as the presence of heterogeneous landfill material and alluvial layers of soft clay (muds).1. INTRODUCTION Located on the right bank of the Tagus River, in Lisbon, the new Church building of ""Nossa Senhora dos Navegantes"", patroness of fisherman and navigators, with three or four upper floors, is surrounded by a school and by new residential buildings.The Tagus River basin is known by its alluvial soft soils, achieving, in certain areas, more than 50m meters depth, challenging the construction of new facilities due to the significant unfavorable geotechnical conditions.With a modern an unusual architecture, allusive to the ships used by the Portuguese navigators, the building has a reinforced concrete structure, with one basement and three upper floors. A bell tower with about 40m high, emerging from the structure, marks the landscape with the presence of this religious building (figure 2).For all the reasons previously described, geotechnical engineers play a crucial role on the design of valid foundation solutions, from both technical and economic point of view. Ideally, the solutions adopted should be supported by full scale load tests, performed at site, so that design assumptions could be verified and adjusted on time."

Jan 1, 2014

By S. S. Gajin

The paper deals with parametric vibrations of an axially loaded pile. The dynamic model is derived by means of Hamilton's principle and reduced to a partial differen­tial equation with variable coefficients and corresponding initial boundary conditions, taking into account the influence of the axial force. By means of Galerkin's method, the partial equation is further reduced to a Matheu-Hill's matrix partial differential equation of the second order. Since the problem of the dynamic stabili­ty has been expressed only for standing piles, the paper analyses in detail two stan­ding piles, one which is restreined, whereas the other is hinged at the toe. In both cases it is assumed that head horisontal displacement is prevented. Using Ruunge-Kutt's method, a computer analysis in the time domain is given for the characteristic parameters and possible boundary conditions. The paper analyses the stationariness of the process, as well as the dependance of the critical excitation frequency upon the pile parameters. The results have been illustrated by respective diagrams.

Jan 1, 1989

By Sangseom Jeong, Moonkyung Chung, Junyoung Ko

"Abstract The plugging effect of open-ended piles in sandy soil is analyzed by full-scale field test and plugging measurement. PLR (plug length ratio) measurement data from 144 field cases are analyzed with pile diameter. Based on the plugging measurements, PLR of open-ended piles which have above 1000mm diameter is predicted to be above 0.9. Through plugging measurements, a new empirical method is suggested for quantifying the plugging effect of open-ended piles. The proposed PLR equation is possible to predict the behavior of soil plug in the preliminary design stage. In addition, in order to investigate the behavior of the soil plug of open-ended pile, field load tests are performed on instrumented three piles driven into sand. It is obtained that the resistance components of open-ended pile are separated by double-walled pile system. It is found that inner shaft capacity is developed nearby pile tip. However, upper soil plug did not influence the inner shaft capacity. Also, it is found that all test piles are floating piles and unplugged condition because the sum of inner shaft capacity and outer shaft capacity is calculated about 58 to 76% of the ultimate bearing capacity.INTRODUCTIONIn Korea, a number of huge construction projects such as harbor terminals, offshore grand bridges, and lifeline systems are progress in urban and costal area. In these areas, steel pipe piles are frequently used to support high-rise buildings and heavy weight structures for ensuring structural safety rather than serviceability limit capacity. Also, steel pipe piles are frequently used in civil engineering structures because they have many advantages such as high-load bearing capacity, light weight and outstanding workability. The mega foundations of grand bridges and high-rise buildings are required in geotechnical engineering. Large diameter driven piles are frequently used in several projects.Many specifications such as API, FHWA and AASHTO have been reported as a design guideline of plugging effect, however , the current design method for plugging effect of steel pipe piles are mainly based on the our knowledge derived from observation of the model test or the small diameter pile load test. Therefore, these specifications have limitation to apply the large diameter steel pipe piles.Much work has been done to study the plugging effect by many researchers. Yamahara (1964) reported that soil plug has been modeled as a thin disk element as shown in Figure 1, since the increment of radial strain of the soil plug can be neglected due to high rigidity of the pile compared to that of the soil plug. Klos and Tejchman (1977) reported that the end bearing capacity of open-ended piles was almost equal to that of a closed-ended pile when penetration depth of pile was above 15times the pile diameters by model tests. Paikowsky and Whitman(1990) reported fundamental studies on mechanism of plugging effect in sand. Paik et al. (2003) reported that empirical relations for plug load capacity, annulus load capacity, and shaft load capacity of open-ended piles are proposed based on the model pile tests. As discussed above, much work has been done in the area of plugging effect. But little work has been done to study the plugging effect by full scale field tests."

Jan 1, 2014

By Antti J. Perala, Teemu J. Yli-Kovero

"Efficient use of land is constantly requiring more underground construction. Minimized execution time and disturbance to surroundings and nearby structures are essential benefits for all construction techniques. To meet the demands of a modern construction project, suppliers have to be able to provide high-quality and tailor-made products just on time. RD pile wall is a retaining wall based on drilled steel pipe piles which are connected to each other with special interlocking profiles. RD pile wall is a solution which enables penetration of overburden soil, dense fill layers including stones and boulders, and embedding into the bedrock in one single operation. Several test installations and laboratory tests have been made to develop the system and to test and improve the water tightness of the wall. Beside these tests, RD pile wall has also proven its reliability in almost 70 projects. Largest project so far has been Pasila Tripla project in Helsinki, Finland. A permanent retaining wall with surface area of 18,000 m2 (193,750 ft2), excavation depth of 21 m (68 ft) and over 17 m (56 ft) of water pressure was made with 711 mm (28”) and 406.4 mm (16”) pile sizes. Piles were delivered to site in one piece with lengths up to 33.5 m (110 ft).INTRODUCTIONExcavations in cramped city centers and in between of existing buildings and other structures are facing more and more challenges. Installation of sheet pile walls is often problematic or even impossible due to obstacles in ground from old structures and due to demand to extend the excavations to even deeper and harder soil layers. Also installations of secant pile walls are facing difficulties due to cramped construction sites and constantly tightening execution times.On the other hand, an efficient and reliable piling technique suitable for the demanding soil conditions described above, percussion drilling, has been developed since the 1960’s, and especially from the mid- 1990’s, when the concentric drilling method with the ring bit and pilot was introduced. A new retaining wall application, the RD pile wall, was developed by combining that drilling method with the widely used retaining wall solution based on steel pipe piles and welded interlocks (a pipe pile wall normally installed with vibratory or impact hammers).PRINCIPLE AND MAIN BENEFITS OF THE METHODRD pile walls can be used in all soil conditions. Most beneficial the system is in extremely demanding soil conditions where the installation of traditional retaining walls is challenging or even impossible. The RD pile wall is a combination of drilled steel pipe piles and interlocking sections as shown in Fig. 1.Individual RD piles are connected to each other with interlocks welded to the piles on the automated welding line at the workshop. The matching dimensions of the drilling system and interlocking sections allow the installation of RD piles through stones and boulders and even into the bedrock, if necessary, in a single operation. Installation is done by a down-the-hole (DTH) hammer using the centric drilling system and oversized ring bits or a drilling system consisting of a pilot bit and reamer wings shown in Fig. 2."

Jan 1, 2017

By Joseph C. Gillen

This paper discusses the design, construction, and performance of the support of excavation system used at The Atlantic Building jobsite. The support of excavation system had to be adaptable to the different conditions surrounding the site. These conditions included support of four historic building façades, including the nine-story Atlantic Building, as well as support of three historic row-houses along two walls. Directly adjacent to the site is the historic Ford?s Theatre and townhouse. Across a 15? alley is the American Immigration Lawyers Association (AILA) Building, and across a 30? alley is the Federal Election Commission Building and another ongoing excavation. Of historical note, these two alleys were the escape route for John Wilkes Booth following his assassination of President Lincoln. With the excavation being 53? to 58? deep, the system included driven and drilled soldier piles, drilled bracket piles, and two modified tangent walls. The bracing included tiebacks, corner braces, wales, cross lot struts, and a specially designed support system for the nine-story façade. The footprint of the excavation included 12 corners and all alleys and streets were to remain open during construction. The performance requirements for system movement at Ford?s Theatre and AILA Building were ½ inches in the horizontal direction. The modified tangent walls were used in these areas to provide stiffness. The soil conditions at the site were fill material on top of a shallow, sandy, silty, gravel layer on top of a deep layer of soft organic silt and clay. Below the silt and clay layer was fine sandy material at the subgrade.

Jan 1, 2006

By Lok M. Sharma

"Construction of a new bridge in a seismically sensitive area requires careful assessment of earthquake impact on the serviceability of the facility. Not only is the superstructure vulnerable, the foundations play a key role in the bridge’s survivability. A new bridge in eastern part of the state of Missouri in the U.S.A. is located in a seismically active area and hence subject to additional thrust on the foundations and superstructure and potential damage due to liquefaction. An eleven span bridge with foundation soils varying from shallow bedrock to over 30 m (100 feet) overburden soils were considered for the bridge support piers. Two of the bridge support bents located within the flood plain area through over 30m (100 feet) of alluvial deposits were considered most affected by an earthquake event due to the additional thrust and lateral ground spreading. This paper describes the determination of site specific seismic hazard, numerical modelling of the foundation system, and methodology of dynamic analyses, effects of lateral spreading and liquefaction potential on bridge support bents. From numerical modelling using FLAC, the increase in thrust on piers and deformations were computed to predict the behavior of the foundations.INTRODUCTIONA newly constructed bridge on route US 40 crosses the Missouri River west of St. Louis, Missouri and upstream of Mississippi River in mid-west USA. The west abutment area has near surface bedrock while the east abutment area has overburden deposits over 30m (100 feet) thick, mostly river sediments comprising of silts, lean clays and sands overlying bedrock. Softer layers of silts and sands in the east river bank area are assessed to be liquefiable during a high magnitude earthquake event. St Louis area has a potential for a high magnitude earthquake due to the New Madrid Fault some 160km (100 miles) south. The bridge foundations were designed as drilled piers, 2 m (8 feet) in diameter and socketed into the bedrock. Bents No. 10 and 11, located in the lower flood plain area of the river, are considered to be most affected by a seismic event.In order to perform dynamic analyses of the foundations, earthquake ground motion time history was developed for the specific site using a Probabilistic Seismic Hazard Analysis (PSHA) and selecting and scaling of a recorded time history. Relying on the U.S. Geological Survey (USGS) Earthquake Hazard Program for the PSHA and AASHTO Guide Specifications for LRFD Seismic Bridge Design, spectral acceleration values for the site were developed. The spectral acceleration values were for a 7 percent probability of exceedance in 75 years (1000 year return). Numerical modelling using FLAC computer program was performed. This paper presents the seismic design parameters, methodology used in the dynamic analyses, static and dynamic analyses, impact and mitigation of liquefaction on Bents 10 and 11 and the abutment fills, and effect of lateral spreading on the foundations in the lower flood plain area of the bridge. From the numerical modelling, increase in thrusts on pier foundations and estimated deformation were computed."

Jan 1, 2017

By J. Nakayama

Construction of foundation piles or diaphragm walls through rocky or boulder containing formations has been long-standing difficulty. It has been widely understood that the down-the-hole hammer is the most capable mechanical means but is restricted in drilling diameter by the unavailability of drillhead sufficiently large diameter and the difficulty of disposal of cuttings. A great number of submersible motordrills have been used for the construction of cast-in-place piles and diaphragm walls and the reverse circulation system employed has demonstrated its advantage of the prompt removal of cuttings. The development of multi-head down-the-hole hammer drill combined with reverse circulation system presents a powerful engineering choice for those "hard-to-drill" ground formations. This paper will introduce the features of the system and some actual operation results in the foundation engineering through those hard rocky ground formation in some countries.

Jan 1, 1989

By K. Viking

The vibratory characteristics of full-scale sheet piles, vibratory driven into the ground, have so far not been described systematically in detail. This paper concerns the preliminary results of a series of full-scale field tests where both the driveability and induced ground vibrations have been continuously monitored. Furthermore, the results of measured ground vibration levels have been measured at two different sites characterised as having hard and easy driving conditions. In the light of the presented results, the paper briefly discusses how the complexity of a driveability and vibration prediction can be subdivided into three parts, namely, vibrator-, sheet pile-, and soil-related parameters, all of which significantly affect both the driveability and induced ground vibrations.

Jan 1, 2000