Search Documents

By Filippo Maria Leoni, Wesley Schmutzler

"Deep Mixing Method (DMM) for the Rio Puerto Nuevo Project in San Juan was chosen by the Corps of Engineers to improve the soils adjacent to a 90 inch forced sewer main relocation and to improve the soils for the base of a new drainage channel. The project is located just east of San Juan and south of the Horizon Port. The soils to be improved consisted of fill, marine clay, organics (peat) and the foundation clay layer. A preconstruction soil investigation campaign was performed to assess soil properties and to retrieve samples of the different soil layers for the laboratory Bench Scale Testing program (BST). The BST was conducted using various binder contents and water/cement ratios in each of the soil types; the selection of the different combinations and dosages was based on past extensive experiences on similar materials. Following the laboratory program, a full scale Field Test (FT) was done installing several DMM elements to verify the results of the BST and fine tune the construction parameters. Each element consisted of two 5.5 feet diameter overlapping mixing augers installed simultaneously to a depth of approximately 60 feet using a SOILMEC SR-90 dual axis drilling rig. The FT construction and post-construction coring results showed significant differences between the lab study and the actual field conditions. This paper will highlight these differences and the importance of performing both pre-construction laboratory and field tests in order to ascertain the proper mixing parameters in the different soil layers.IntroductionThe Puerto Nuevo project consists of the stabilization of a major drainage channel using Deep Mixing Method (DMM) and the relocation of a 90 inch forced main sanitary sewer outfall. The first portion of this project was a 40 x 16 x 2,000 foot box culvert installed in 2004. In order for the drainage system to be completed and function properly, the 90 inch forced main needed to be lowered about 20 feet to allow for proper drainage.DMM was chosen by the US Army corps of Engineers to stabilize the drainage channel as well as improve the soil under the relocated sewer main. The overall layout of the project is shown in Figure 1. The DMM is arranged in different zones (A through E) with variable top and bottom design elevations as can be seen in the typical cross section for ZONE A and B as an example. (Figure 2) The total amount of soils to be treated by DMM is approximately 84,000 cubic yards up to a maximum depth of 57 feet from ground surface and an Area Replacement Ratio of 100%.The equipment used to perform the DMM is a Soilmec SR90 twin-shaft jet assisted deep mixing rig (Figure 3) coupled with a LODOS 30 grout plant and two Soilmec 7T-500J high pressure pumps."

Jan 1, 2015

By James M. Tantalla, Roderic A. Ellman, W. Allen Marr, Scott R. Bamford

"Construction of the powerhouse for the Willow Island Hydroelectric Project required a 100-ft deep excavation inside the limits of a cofferdam and embankment-seepage cut-off wall through soil and rock adjacent to the Ohio River. Portions of the rock had preexisting weak plans and slickensided surfaces with low frictional strength. Stability analyses were performed for critical sections of the excavation to evaluate the stability of the soil slopes and rock cuts using buckling, tension crack, and limit equilibrium analysis techniques. Loading conditions included the 100-yr and intermediate floods, normal pool, sudden drawdown, and seismic design conditions.Stability analyses indicated adequate factors of safety for soil slopes and for rock cuts through the landside embankment sections. However, the results of deep-seated stability analyses through the rock supporting the riverside cellular cofferdam indicated unacceptable factors of safety. Consequently, the riverside portion of the excavation required measures to increase stability. Long, high-capacity rock anchors and deep dewatering wells to lower the site piezometric head were chosen for this purpose.Thirty high-capacity rock anchors were installed on the upstream, riverside, and downstream sides of the cofferdam rock cut. Required rock anchor loads varied from 1,968 to 2,074 kips. The designed anchors consisted of multiple, seven–wire strands with up to 59 strands per anchor. Bond lengths used an allowable bond stress of 100 psi based on the rock bond measured with pull-out tests. Maximum bond and anchor lengths were 50 ft and 140 ft, respectively. Measurements of forces in selected strands and displacements of the excavation showed excellent performance."

Jan 1, 2017

By Bill Shea, Gordon King

"For a drainage channel built in San Juan, Puerto Rico, a value engineering (VE) proposal incorporating a secant pile top-down approach saved time and facilitated construction work on the larger flood control project. The channel, at the Bechara Industrial Area, Puerto Nuevo Port Facility and the Puerto Rico Maritime Shipping Authority Dock, was needed to allow drainage of the Rio Puerto Nuevo into San Juan Bay. The port area, one of the busiest in the Caribbean, has over 6,000 ft (1,800 m) of berthing wharves for ocean-going container ships along with over 500,000 sq ft (46,000 m²) of container loading and unloading areas, and is critical to the local economy.Planners wanted to minimize the impact of construction to the port and dock users, and developed a construction methodology and work sequencing that would prevent a complete barrier to port traffic. This plan involved non-contiguous and limited work area that “leapfrogged” along the alignment so as to prevent long barriers to lateral traffic movement across the culvert alignment.After reviewing the project plans and schedule, Morris-Shea Bridge Company (MSB) proposed an alternate design and construction approach that provided significant cost and schedule benefits, and also provided better access for the port and dock users. The alternate VE proposal involved top-down construction methodology and redesigned drainage culvert geometry with two parallel 2,000 linear ft (lf) (600 m) secant walls installed on each side of the culvert. These walls facilitated excavation and formed part of the culvert permanent walls. The result was a significantly reduced required construction right of way that allowed construction work in contiguous areas largely without impact on ongoing port activity. MSB conceived the design concept, and engineered design and construction of the VE alternate secant pile culvert.The project initially consisted of an open channel in the industrial area picking up water from the existing Rio Puerto Nuevo, transitioning to an enclosed culvert through the port and dock areas, and outfall through the existing dock. The base bid construction included three main areas of work:"

Jan 1, 2012

By Ronald E. Walkington

The U.S. Department of Energy (DOE) is building the world's newest accelerator-based, pulsed-neutron system, called Spallation Neutron Source (SNS). The facility, located in Oak Ridge, Tennessee, is a partnership of six DOE national laboratories - Argonne, Brookhaven, Jefferson, Lawrence Berkeley, Los Alamos, and Oak Ridge. Oak Ridge has the responsibility for managing the partnership and ultimately operating SNS. SNS will provide opportunities for up to 2,000 researchers each year from universities, national laboratories and industry from around the world for basic and applied research and technology development in the fields of materials science, magnetic materials, polymers and complex fluids, chemistry and biology. When completed, this state-of-the-art research facility will provide neutron beams that are 12 times more intense than any other such source in the world. Most of the world's neutron sources were built decades ago. Therefore, it is easy to understand how SNS will provide new research opportunities unavailable elsewhere, and at the same time restore United States leadership in neutron sciences. Neutron scattering research provides valuable information about materials that cannot be obtained through microscopy, X-rays, spectroscopes, or other techniques. The information gained from neutron scattering research leads to improved materials that are used in high-temperature superconductors, powerful lightweight magnets, aluminum bridge decks, jet aircraft, compact and computer discs, magnetic recording tapes, shatter-proof windshields, and many other applications. SNS is like a flashing strobe light providing high-speed illumination of an object and will record the structure of physical and biological materials from plastics to proteins. Because neutrons have no charge, they can penetrate more deeply into materials than do X-rays, light, or electrons and thus reveal bulk structure and properties of materials. SNS will help to understand and "engineer" better materials and the manufacture of better products at the atomic level. Our high-technology society demands new materials that are stronger, lighter, and cheaper yet perform well under severe conditions. SNS, which is designed with the future in mind, will be the leading neutron research facility for many years to come.

Jan 1, 2001

By Joshua R. Omer

A numerical model is developed for predicting the load transfer and settlement behaviour of vertically loaded, bored cast in-situ piles. Based on analysis of full-scale pile tests, closed-form equations are formulated to uncouple the shaft and base transfer resistance components of the pile/soil system. Appropriate parameters are introduced to take into account: (i) the shaft resistance distribution in unlined and partially lined piles, (ii) the effects of ?soft toe? (voided toe pile) behaviour on base resistance development. For convenience, an interactive computer program has been developed in Matlab? with a user friendly interface system. The program can be applied to predict the complete load-settlement curve and axial force distribution in bored cast in-situ piles if reliable soil test data are available. To demonstrate its validity, the proposed method is applied to 4 test piles, which are also analysed using two previously published methods: (a) elastic solution method and (b) layer discretisation method. Methods (a) and (b) above are based on load transfer (t-z) and finite element models respectively. It is shown that the proposed method yields axial force distributions and load-settlement curves that are in good agreement with the observed pile test data.

Jan 1, 2010

By Ziyad Abunada, David O’Connor, Fei Jin, Abir Al-Tabbaa

"In-situ remediation of contaminated land with deep mixing can enable a multi-technique remedial strategy on the same site combining low permeability barriers, permeable reactive barriers, stabilisation/ solidification treatments as well as ground improvement, delivering significant advantages over alternative strategies. This was the core objective of Project SMiRT (Soil Mix Remediation Technology) which involved the execution of the largest research field trials in the UK to date to provide field validation for this technique. Around 800m3 of soil were treated on a contaminated site in Yorkshire in May 2011 with 6 different treatments, testing ~40 binder compositions and 10 different installation methodologies. Field monitoring, testing and coring activities at the site took place within the first 2 months after treatment and then again at 34 months after treatment. This paper presents an overview of the field activities to date and some 3-year results and assessment of a subset of the treated soil sections. Some good correlations are seen together with some clear differences between treatments. There is generally an observed consistency with depth, with the mixing effectiveness having a more profound effect than the binder composition or content, within the tested materials and ranges. These field trial activities are currently being used in the development of the full-scale commercial remedial strategy for the site.INTRODUCTION AND OVERVIEW OF PROJECT SMiRTWhile there are strong financial and environmental incentives to remediate and redevelop brownfield sites there are also barriers including fear of the unknown, regulatory control, delays, increased costs and the stigma associated with such sites. Hence the remediation process needs to be conducted in such a way to maximise the incentives and overcome the barriers, which is how deep mixing found its niche in the land remediation market. Soil mix technology is such a versatile technique that can perform a number of remediation treatments on the same site. These include low permeability in-ground barriers (cut-off walls), permeable reactive barriers (PRB), stabilisation/solidification (S/S) treatments, other additive related remediation, e.g. in-situ chemical oxidation and bioremediation, as well as soil amendments for greening and also ground improvement all on the same site (Al-Tabbaa et al, 2011). Placed in the context of alternative solutions, soil mix technology could potentially replace the five techniques shown in Figure 1, which would be required to deliver the same treatments mentioned above. Treatment trains strategy, where a combination of techniques in succession are used to both reduce the contamination levels and deal with residual contamination, is becoming common in land remediation and the use of one set of equipment to deliver this would bring about significant financial advantages. In addition, soil mix technology has many other advantages in terms of speed of implementation, elimination of exposure to contamination, elimination of off-site disposal and low cost. Soil mix technology for the remediation of contaminated land emerged in the UK in the mid 1980s and has since been employed in over 30 or so projects, which far exceeds its application to ground improvement for which only a handful of jobs have been carried out to date."

Jan 1, 2015

By M. Meckkey El Sharnouby

In this paper, the results of full-scale field testing of reinforced helical pulldown micropiles (RG-HSP) installed in clayey till soils and resting on sandy soils are presented. Piles were tested under monotonic and two way cyclic lateral loadings. Effect of different loading setups on the results is demonstrated. The factors affecting the piles' performance are discussed. It was found that under monotonic loading the piles were able to sustain displacement up to 50% of the grout shaft diameter. Under low cyclic loading levels, the piles did not suffer degradation in the performance. Also, the degradation rate during cyclic loading increased with the increase of the load level. The experimental results show that the reinforced helical pulldown micropile is a reliable foundation option for lateral monotonic and cyclic loading applications.

Jan 1, 2011

By Olgun

Energy piles are a new innovative renewable energy technology to access and exploit the relative constant temperature of the ground for efficient heating and cooling of buildings. Examples of energy piles include drilled shafts, continuous flight auger (CFA) piles, driven piles, and micropiles. A field test setup was installed at the Virginia Tech Geotechnical Research Facility to study energy piles. The field test consists of a total of five micropiles 25 cm (10 inches) in diameter, four of which were equipped with circulation loops. The test piles extend to a depth of 30.5 meters (100 feet) and are heavily instrumented with strain gauges and temperature sensors. Several observation boreholes were formed around the test piles to monitor ground temperatures. Thermal conductivity tests and field load testing were performed to investigate the behavior of Energy Piles. This paper presents results of the thermal conductivity tests and thermo-mechanical field load test performed as part of this field investigation.

By Rohrbach

Crosshole Sonic Logging (CSL) testing is commonly used to verify the integrity, quality and ultimately the acceptability of the concrete in structural elements such as drilled shaft foundations, secant pile cutoff walls, and secant/tangent pile earth retention structures. Besides concrete quality, many factors can impact CSL test results (e.g. laitance, air temperature, access tube spacing, access tube debonding, etc.). Effective use of CSL testing requires fully informed qualified practitioners capable of distinguishing between abnormal readings unrelated to deficiencies in the drilled shaft concrete and similar readings indicating the presence or possible presence of drilled shaft defects. Based on data and experience gathered from CSL testing of thousands of drilled shafts across North America, this paper discusses such factors and other information useful when evaluating CSL test results, and provides practical recommendations intended to reduce the potential for incorrect test data interpretation. The CSL testing industry is lacking in a clear, universally accepted guideline for the interpretation of CSL data and acceptance criteria of these concrete elements. This paper proposes terminology and a streamlined process for use when atypical results are obtained. The proposed terminology and method are intended to simplify and expedite the submittal review and approval process. Because construction activities for these elements are often on the project?s critical path, the benefits obtained in terms of project savings and reducing costly delays are undoubtedly valuable.

By Karsten Beekhaus, Sander W. Odijk, Rabea Bahlum, Mazin Adnan, Ayman Abdelh Al Nuaimat, Hassan Farhat

The Arab Potash Company, APC, is one of the 10 largest potash producers of the world. The solar ponds at the Dead Sea, used for the enrichment of the salt content in the brine, are of crucial importance for the first step in the exploitation of the potassium salt. Targeting at the expansion of production in the since over 50 years utilized facilities, the increase of the brine exploitation capacity, reducing the substantial brine seepage losses from the ponds, becomes a crucially required measure. In this context, the remediation measures on the over 11 km long Dyke 1, being a main dyke of the solar ponds system, became inevitable to reduce the brine losses, prevent further development of sinkholes and cavities and hence assuring the stability of the dyke. The highly aggressive environment, the acting hydraulic conditions and the sensitive stratification and nature of the existing ground represented remarkable challenges for the design, as well as its implementation by the construction activities. Royal Haskoning developed a solution addressing the challenges above and targeting at a high sustainability of the executed structure, especially in view of the various geological and hydrological hazards repeatedly occurring in this Dead Sea region, including sinkholes of several meters by diameter and depth. The construction works, consisting of a cut-off wall, with depths reaching down to 31 m, were awarded to Bauer International FZE, a subsidiary of Bauer Spezialtiefbau GmbH. Upon the execution of the first section of 4.2 km length, additional sections were subsequently commissioned, also on further dykes, totaling to about 300,000 m² of cut-off wall. The specific project conditions, such as utilization of cutter technique for the excavation in Halite rock, the stability of open trench exposed to hydrostatic pressure of salt-saturated ground water, resulted in unconventional requirements towards the supporting fluid. The extremely aggressive saline conditions –with a Dead Sea water density of 1.25 tons/m3; one of the world's saltiest water–, were further a decisive factor for the definition of the backfill material concept. Despite its clear advantage for construction of cut-off walls with installed sheet piles, the single-phase system with hardening slurries, fulfilling both functions of excavation support and cut-off wall backfill material, had to be abandoned in favor of the two-phase system, to construct a hybrid cut-off wall made of sheet piles and plastic concrete.

May 1, 2022

By Nicolas Denies, Jeroen de Leeuw, Bart Lameire, Jan Maertens, André Vervoort, Flip Hoefsloot, Noël Huybrechts, Flor De Cock

"In recent years, the Deep Mixing Method has increasingly been applied for the construction of earth and water retaining structures. From practice, it has been experienced that there is a real need to develop execution and design rules adapted to the function of the soil mix wall (retaining wall, water barrier, foundation solution or a combination) including the temporary or permanent character of the application. Based on the results of the BBRI Soil Mix project (2009-2013), a design approach has been developed in collaboration with the SBRCURnet. The present paper briefly discusses the principles of this design approach which takes into account the function of the soil mix wall and the characteristics of the soil mix material. The interaction between the soil mix material and the steel reinforcement can be considered in the calculations depending on the function of the soil mix wall. Design and quality control requirements are given in function of the application and take the lifetime of the structure into account. Durability aspects of the soil mix material are therefore considered in the present design approach.INTRODUCTIONSince several decades, the deep mixing method is used for ground improvement works. A more recent application is the use of soil mix as structural elements such as in the case of the earth-water retaining soil mix walls. Since 2000, due to the economic and environmental advantages of the method, this particular application has shown an amazing growth in Belgium and in the Netherlands. A typical excavation (16 m depth), realized with CSM (Cutter Soil Mix) panels, is shown in Fig. 1. For temporary applications, the questions related to the mechanical characteristics of the material, its permeability and its adherence with steel have been investigated with success within the framework of the BBRI Soil Mix project (2009- 2013) (see Denies et al. 2012 for more details). The durability of the soil mix material remains a complex topic while permanent applications are more and more observed in practice. In order to define an obvious design approach, it was necessary to clarify the potential functions of soil mix walls and to establish the requirements related to their design and construction. The BBRI (in Belgium) and SBRCURnet (in the Netherlands) have therefore worked together to publish guidelines in the form of a handbook titled ‘Soil Mix Walls’ (publication foreseen in 2015). In this handbook, a methodology is proposed for the design of the soil mix walls for which the interaction between steel and soil mix can possibly be taken into account dependent upon the application. Each potential function of the soil mix wall is described (e.g. earth retaining wall, cut-off wall, etc.) and the temporary or permanent character of the application is always considered."

Jan 1, 2015

By M. Hesham El Naggar, Maged A. Abdlrahem

"Hollow bar micropiles have constructional advantages such as: fast and low-noise and low vibration installation process and small installation equipment, which allow access to tight places. In addition, they have efficient load transfer mechanism, which facilitates carrying considerable load in compression and tension. The common practice is to use diameter ratio of drill bit/ hollow bar (Db/Dh) around 2 in their construction, and they are typically designed assuming type B as classified by the Federal Highway Administration (FHWA). In this paper, the performance and capacity of Hollow bar micropile with different (Db/Dh) ratios are investigated. Full-scale micropiles were installed at a site in Ontario, Canada, and were tested in order to evaluate the uplift performance of Hollow bar micropile with different(Db/Dh) ratios. Two micropiles with two different ratios 2.25 and 3 were constructed and tested. The total length of the micropiles was 6m with embedded length of 5.75m. The soil at the site was primarily medium dense to dense sand. The results of the load tests are presented and discussed. It was found that the uplift capacity of the micropile increased by about 19.5% as Db/Dh increased from 2.25 to 3.INTRODUCTIONMicropile is a small diameter, less than 300 mm, drilled and grouted pile and is typically reinforced according to Federal Highway Administration (FHWA, 2005). The technology of micropile was introduced in North America in 1970’s, but the growth in the east coast of United State was intense compared to all other cities around the globe (Bruce and Nicholson, 1989). Nowadays, micropile construction is used extensively worldwide as a viable solution that offers several advantages such as fast installation in low headroom, minimal disturbance to the adjacent structure efficient load transfer due to high grout to ground bond strength. As the method of grouting has major influence on the grout – ground bond strength, FHWA has classified the micropiles into four categories. Type A: the grout is placed under gravity and no pressure is required. Type B: The grout is typically pressurized under a pressure range from 0.5 to 1 MPa as the temporary casing is withdrawn. Type C: the grout is placed in two-step process. First, the grout is poured under gravity only as in Type A. Before the hardening of the grout, similar grout is pressured of at least 1MPa without the use of packer. Type D: Like Type C, it is a two – step process, the grout is placed under gravity as in Type A and sometimes pressurized as in Type B. After hardening of the initial grout, additional grout is pressurized between 2 to 9 MPa through sleeved pipe by using packers, as many times as needed. According to this classification, hollow bar micropile is usually designated as Type B. However, the construction technique is completely different from Type B. Recently; there is a trend to supplement the four types of micropiles by Type E as represent to hollow bar micropile (Timothy et al, 2012). The construction method of hollow bar micropile involves two main stages which can be performed in one–step process: advancing the drilling bit attached to a threaded hollow bar to the required depth; and pressurizing the grout through nozzles of the drill bit."

Jan 1, 2016

By Mai Yuanjian

The stabilization effect in large excavation slope with vacuum wellpoints system during construction of a dry dock located in Guangzhou is introduced in this paper. In-situ observations indicate that the effect of wellpoints for decreasing seepage in slope is remarkable even though the muddy sitty clay in it has poor permeability and the slope can remain its stability well. Meanwhile, a non-linear partial defferential equation has been set up to the whole unsteady seepage process as water level in the foundation pit excavated under water goes down to the bottom and so does the seepage in slope due to dewater by vacuum wellpoints system at the same time. And the finite-defference method has been used to solve the equation mentioned above, which differes from conventional wqy where the equation will be linearized firstly. Since the water heads in slope with wellpoints dewatering are more variable, it is necessary to keep non-linear. The calculation results are in good accordance with observation. Vacuum wellpoinnts for slope stabilization in this work is successful.

Jan 1, 1991

By Yahia M. Al-Smadi

Effect of lateral loading against existing sheet pile wall and distribution of gravity loading due to various number of construction loading scenarios were studied. The objective of this effort was to determine the loading case that permits the contractor to utilize a 400 ton crane at the specified location with the existing limitation imposed on site. Staged analysis was determined as the methodology that will more accurately predict the exiting and additional stress due to the impose crane loading. A reliable and robust analysis (ANSYS) software was used to complete both 2D and 3D finite element model and analysis. Analysis model parameters such as material properties, non-linear behavior of the soil, and meshing are presented and discussed. At the conclusion specific range of crane operation and pick weights operating on existing concrete mat supported on top of an existing tunnel was reviewed and deemed acceptable.

Jan 1, 2010

By Alison Savage, Michael Terry

"For decades, the International Market Place (IMP) has been an icon in the heart of Waikiki in Honolulu, Hawaii. It was famous for Duke Kahanamoku’s restaurant where people flocked to hear Don Ho sing in the ’60s and ’70s. Later, it was a bustling, open-air hub of small vendors who peddled everything from Hawaiian souvenirs and jewelry to food court meals and farmer’s market produce. Small buildings and shacks that housed the businesses were located on a curved tract of land — just one block off the beach — that stretches from Kalakaua Avenue to Kuhio Avenue. The entrance to the complex is dominated by a huge, old (circa 1850) Banyan tree. This tract is owned by the Queen Emma Land Company. Queen Emma was a Hawaiian Queen from the 1800s. Revenue from the land has supported the Queen’s Medical Center in Honolulu for decades.The reimagined IMP is owned by Taubman Centers, of Bloomfield Hills, Mich., and CoastWood Capital Group of San Francisco, Calif. The IMP will offer a distinctive collection of upscale fashion and lifestyle retailers, including Hawaii’s only Saks Fifth Avenue store, as well as ten sit-down restaurants, including concepts by award-winning chefs Michael Mina and Roy Yamaguchi. The mall features two large open-air courts, the first of which has the huge Banyan tree as its entryway centerpiece. The second open-air court, called Queen’s Court, includes a stage and mature monkeypod trees and a few palm trees. Foundation SelectionAfter a geotechnical exploration that was directed by SME, Plymouth, Mich., and performed by Geolabs, Honolulu, it was discovered that the historical site had hidden and challenging foundation conditions. The subsurface conditions included a very deep but now in-filled ancient river valley containing more than 180 ft (54.9 m) of lagoonal deposits consisting of normally consolidated plastic clayey silts and silty clays with blow counts mainly varying in N-value from 1 to 6. The silt was underlain by several soft coralline layers, some overconsolidated clays and various basalt layers. The static groundwater level on the site was at a depth of about 5 ft (1.5 m), closely matching sea level.Although driven piles had previously been used as the preferred deep foundation support for adjacent structures, this area of town is now fully developed and local noise ordinances preclude their use. Augercast piles were initially considered, but when the general contractor dck/FWF, Pittsburgh, Pa., asked for bids for the augercast piles, several foundation contractors offered alternate systems. The practical installation depth of augercast piles was limited and due to the depth of the in-filled alluvial valley, this system could likely have left soft silt below the tips of the piles over much of the site."

Jan 1, 2016

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Numerical lateral load analysis based on the beam on Winkler foundation (BNWF) model (i.e., the p-y method) is a simple, and widely used tool to predict lateral responses of drilled shafts from field load tests. The lack of a site-specific p-y model for cemented soil layers such as caliche is one of the major limitations of simulating lateral load tests conducted in Las Vegas Valley. In this study, some of the existing p-y models for rock materials, such as Florida Limestone and Vuggy Limestone have been evaluated to simulate the lateral resistance of caliche. This has been done in the context of four lateral load tests in caliche-dominant sites from the recently constructed Raiders Stadium project in Las Vegas (NV). The uncertainty in characterizing the material properties of caliche has been addressed. The p-y analyses were performed using NVShaft, a MATLAB-based, comprehensive load analysis program. The applicability of the considered p-y models for caliche material was evaluated by quantifying the normalized error margins between measured and predicted lateral responses from the simulations of the mentioned load tests. Correlations between such errors and the depth and thickness of caliche in soil layers affecting numerical predictions were established, for both up to and beyond design load levels.

Oct 1, 2022

By Naoyuki Hanawa, Takeo Asanuma, Tatsuo Nagatsu, Sachihiko Tokunaga, Daisuke Nakagawa, Yoshiyuki Morikawa, Kazuhiko Ueno

"In the cement deep mixing (CDM) method, one approach to joint construction is creating a surface-contact joint. In this study, an unconsolidated-undrained triaxial compression test was performed on cement-treated soil specimens with joints artificially created by successive pouring. The effects of the presence or absence of such successive pouring joints on the strength of the specimens were then examined. The results showed that the compressive strength of the specimen decreased by approximately 0%–30% with a successive pouring joint.INTRODUCTIONIn the block type and wall type improvement patterns of the CDM(Cement Deep Mixing Method) application, an integrated body of soil-cement columns is constructed by partially overlapping individual treated soil columns. The overlapping operation should be implemented before the hardening of soils by cement progresses and thus, this operation is routinely performed in construction sites usually within 24 hours or within 48 hours at a maximum. However, when the operation is forced to be interrupted on account of a typhoon or any other adverse weather conditions, it is impossible to carry out the overlapping operation within the above time limitations. In such a case, it is necessary to improve the integrity between the treated soil columns solidified first and the treated soil columns to be constructed later.One of the methods that can be adopted is to prior agitate the target area by mixing blades “without cement”, integrating the preceding treated soil columns and the subsequently treated soil columns at construction joints. This method has been adopted so far in numerous sites because no additional materials or equipment are necessary. However, its effectiveness has scarcely been evaluated quantitatively in conventional studies.In the circumstances, the authors investigated in the present research the effect of the presence or absence of construction joints on the specimen strength by performing unconsolidated-undrained triaxial compression tests using specimens of cement treated soil artificially provided with surface-abutting construction joints.Therefore, this study examined the effects of the presence or absence of artificially created successive pouring joints on the strength of cement-treated soil specimens through an unconsolidated-undrained triaxial compression test."

Jan 1, 2015

By Alexander Blatt, Franz-Werner Gerressen

Diaphragm wall technique is usually used to construct structural elements in the ground, commonly used for retention systems, permanent foundation elements or deep groundwater barriers, named Cut-Off-Walls (COW). Recent developments proof, that the technology also satisfies the demands for using the diaphragm wall technique for bulk sampling purposes. Such kind of new ideas required the adaption of equipment and tools for a depth capability never reached before by a trench cutter in any commercial application worldwide. Compared to the development of increasing depths, especially inner-city applications with limited space, demand a minimization of equipment to accommodate such projects. The paper will focus on the developments and solutions generated to fulfill these requirements and will give an outlook to future developments. Further it describes finalized reference projects and will give a general outlook on future trends and developments. The Paper/The Presentation explains as well the installation process in general.

May 1, 2022

By Silvana B. Foá

Results from full-scale loading tests showed the use of the dynamic increasing energy test (DIET) to verify the capacity of deep foundations. This method allows the measurement of dynamic resistance - displacement curve and the prediction of the static resistance -displacement curve of the pile-soil system. The comparison between the use of DIET versus the static load test is also considered herein. This work was divided in two different phases, the first accomplished in Salvador (Bahia) and the second in Brasilia (Federal District), both in Brazil. The first phase consisted of field loading tests carried out on piles comprised by an approximate 10 to 12 meters thick deposit of fine saturated sand, overlying a stiff clay layer, which is found in certain areas of the Brazilian Northeast. Two metallic (rail track) piles were field loaded in this site. One of them was dynamically tested and the other was statically tested. The second site belongs to the Post Graduate Program of the University of Brasilia. It is comprised by an approximate 8 to 14 meter think deposit of porous clay, overlying a hard strata of saprolitic state. In this site a unique precast driven centrifuged pile was tested. The DIET procedure has demonstrated to be a tool of fast execution and low cost (if compared to static load test). It is a promising procedure to evaluate the behavior of pile-soil system.

Jan 1, 2002

By Jeffrey A. Gebhard

As part of the design and construction of the new St. Anthony Falls I-35W Bridge, a full-scale load test was conducted on a 6 1/2-foot diameter drilled shaft in the St. Peter Sandstone. This load test helped identify shaft-rock interaction properties, including end bearing and multiple zones of differing shaft resistance for design of the drilled shafts beneath the three piers adjacent the river. The load test was designed by Load Test, Inc., Braun Intertec and the design team of Figg Bridge Engineers/TKDA and constructed by Design Build Consortium of Flatiron/Manson. Oversight was provided by the Minnesota Department of Transportation. Based on these test results, the drilled shafts supporting the St. Anthony Falls I-35W Bridge were designed to reduce risk and maximize economy for the people of the State of Minnesota.

Jan 1, 2009