Search Documents

By Martin B. Hudson, Kenneth S. Hudson, Gwendolyn Arreguin

A twin high-rise project site in Century City posed several foundation engineering challenges for the design team. One portion of the twin high-rise project site was required to utilize top-down construction in order to allow a driveway to remain open during construction of the project’s 40-foot deep excavation. The challenge was compounded by the need to utilize a mat foundation to support the high-rise construction and yet have temporary drilled shafts through the mat foundation area that would not create excessive differential settlement. This was accomplished by constructing a deck supported by eight drilled end- bearing drilled shafts with Osterberg load cells and five 7-foot-diameter end-bearing drilled shafts. The Osterberg load cells served to verify the capacity of each of the drilled shafts and preload the soils at the drilled shaft tips. The 7-foot-diameter shafts were constructed with bond breakers to prevent skin friction but instead mobilize end bearing (for settlement compatibility with the surrounding mat foundation). After the drilled shafts were placed, then top-down construction began beneath the driveway, leaving the driveway supported on the drilled shafts. Construction challenges included drilling of the shafts through previously abandoned tieback anchors from an adjacent parking structure basement, as well as cemented layers within the rock materials. The paper describes the use of the various analytical methods used to calculate capacities and check settlement compatibility, the construction and testing methods utilized, and the construction challenges encountered. INTRODUCTION Wood Environment and Infrastructure Solutions, Inc. (hereafter referred to as Wood) performed a geotechnical investigation for the New Century Plaza currently being constructed in the Century City District of Los Angeles, California. The New Century Plaza project consists of the construction of two new towers (designated as North and South Buildings) and the rehabilitation of the existing Hyatt Regency Century Plaza Hotel. The existing hotel tower is 15 stories in height above the existing grade and is underlain by four subterranean basement parking levels. The new North and South Buildings will stand approximately 46 stories in height above the existing grade to accommodate residential use. The new towers are planned west of the existing hotel. The site was previously occupied by the existing hotel subterranean parking structure and overlying podium structure, and a loading dock in the southwest portion of the site. The former western portion of the podium and subterranean parking structure west of the existing hotel building western edge were demolished to allow for new subterranean levels, a new podium structure, and the new towers. The lowest floor of the proposed subterranean level required excavation on the order of 35 to 80 feet.

Jan 1, 2019

By Dominic Ammon, Mark Rothbauer, Paul Landers P. E.

Across the Potomac River from the location of the DFI47 Annual Conference (October 2022), in Alexandria, VA, two large permanent anchored walls with a decorative shotcrete face were recently constructed for the North Hill project, a new multi-family and townhome development. The project was executed with a design-build approach for the Fairfax County Redevelopment and Housing Authority with review by the Fairfax County Geotechnical Review Board. The project was constructed in highly variable Potomac group sediments that include high plasticity clay/silt terrace deposits overlying coarser grained materials. The soils were over consolidated and exhibited potential for slickensides from relief of horizontal stresses from past erosion. The wall system was designed to include deep soldier piles and permanent long strand anchors considering past slope instability in the area. As the construction progressed, problematic soil conditions and water issues required modifications to drilling methods. The two permanent walls spanned 800 and 1,000 feet long with a maximum height reaching 40 feet.

Oct 1, 2022

By Don C. Warrington

This paper describes a new wave equation analysis program called ZWAVE, which is a program specifically for external combustion hammers. The program is de-scribed in detail, the discussion dealing with topics concerning the program such as 1) the numerical method the program uses to integrate the wave equation, which is different from most other wave equation programs; 2) the modelling process of both cushioned and cushionless hammers; 3) the automated generation of mass and spring values for both hammer and pile; 4) the method of dealing with plastic cushions; 5) the use of a recently developed model for computing shaft resistance during driving; 6) the computation and generation of values based on basic soil properties such as shear modulus, Poisson's Ratio and soil density; 7) the completely interactive method of feeding data to the program; 8) the method used to compute the anticipated rebound and the energy used to plastically deform the soil; and 9) the format of the inter-active input of the program and the program's output. Sample problems for the program, along with comparison of the program results with data gathered in the field, are presented.

Jan 1, 1988

By Mohsen Elsayed, Amr Sallam, Ahmad Mohamed, Xuebing Zheng, Mohamed Alrowaimi

The foundation is an essential component of the wind turbine that ensures continued operation under stable and safe conditions. Both shallow and deep foundations are utilized to support wind turbines including gravity spread foundation, anchor foundation, pier or drilled shaft foundation and pile and pile cap foundations. Conventional methods were typically utilized to design the wind turbine foundations. With the advances in numerical modeling in the geotechnical field, foundation designers may utilize numerical analysis to design wind turbine foundations. Geotechnical numerical packages allow modeling structural components and soil-structure interaction that is usually neglected in conventional methods. Furthermore, the subsoil conditions, geometries, stress-strain behavior, boundary conditions and load staging can be modeled, minimizing the assumptions and generalization. This results in better understanding of the stress strain behavior of the foundation leading to optimized foundation designs. This paper includes a brief review of current foundations used to support wind turbines with an emphasis on post tensioned single pier foundations. The current conventional foundation design methodologies and state-of-the-art foundation design utilizing numerical modeling of the single pier foundation will be discussed. Two case histories where the single pier foundation, designed using numerical modeling, were utilized to support the wind turbines will be presented. INTRODUCTION The foundation is an essential component of every wind turbine that ensures continued operation under stable and safe conditions. Turbine manufacturers provides load specifications for designers to be utilized for wind turbine foundations design. Loads include bending moments, torsional moments, lateral forces and vertical forces in both operational and extreme wind conditions. Essential specifications under seismic conditions might also be provided in seismic prone areas. Turbine manufacturers also include foundation design criteria including minimum rotational stiffness, minimum horizontal stiffness, maximum allowed inclination and maximum allowed lateral movement under both operational and extreme loads. Geotechnical explorations and evaluations are typically performed at early stages of the wind development projects. The field explorations usually include Standard Penetration Test (SPT) borings, Cone Penetration Test (CPT) Soundings, geophysical surveys, and laboratory tests to define soils stratification system and soil strength and compressibility characteristics. The most critical soil parameters for turbine foundation design are shear strength parameters (cohesion and friction), shear modulus, Poisson’s ratio, and unit weight. The depth to the groundwater table is also a crucial parameter in design. Advanced field explorations techniques such as Dilatometer Tests and Pressuremeter Tests may also be utilized. Laboratory tests for foundation design typically include index parameters, consolidation and triaxial tests.

Jan 1, 2019

By Joel B. Dellaria, Justin R. Lewis

"No. 9 Walton is a new high-rise condominium building located in the Gold Coast area of Chicago. The adjacent building, Walton on the Park, featured 4 levels of below grade parking and utilized a secant pile wall with integral drilled shafts to support the exterior columns. The earth retention system (ERS) for No. 9 Walton also employed a secant pile wall in combination with drilled shafts. The excavation into the soft Chicago clays varied in depth from 9.75 m to 12.5 m (32 feet to 41 feet) below grade. The temporary excavation support used internal braces from the new secant piles to the existing foundation system of Walton on the Park to provide earth retention. Engineering teams for both projects worked together to design the bracing scheme and connections to ensure that the new excavation and internal bracing would not overstress any elements of the existing structure. Further complicating the project, immediately to the west of the project was a historic church founded on shallow spread footings which required underpinning to minimize movements.The project involved three different building owners, small values for acceptable wall movement, an extensive monitoring program and the challenges of merging two earth retention systems. The subsurface conditions at the site, the adjacent structures, the excavation, and the performance are described. A summary of the design methods and the expected movements of the ERS are discussed, and the performance monitoring system is described. Overall, the ERS performed better than expected with less than 1 inch of measured lateral wall movement during and after the excavation was completed. Measured performance of the ERS is compared to the predicted performance and to the performance requirements for the project.INTRODUCTIONNo. 9 Walton is a new high-rise condominium building in Chicago located in the Gold Coast. The building has 3 levels of below grade parking and 36 levels of living space above grade. Developers originally slated the project to be Phase 2 of the Walton on the Park development built in the mid 2000’s, using portions of the existing foundation system for development of the new structure. However, the housing market crash in 2007 prompted cancellation of Phase 2 of the Walton on the Park development. The property sat undeveloped until 2015 when design and construction for No. 9 Walton began under a new development and design team. The project team completed foundation excavation and below grade structures in 2016 with the first units of the building turned over to new homeowners in 2017.The structural design for No. 9 Walton consisted of reinforced concrete columns and slabs, supported laterally by a heavily reinforced concrete central core. Drilled shafts to rock supported the interior columns and core with the exterior columns and foundations integrally included in the earth retention system. The structure had a below-grade footprint of approximately 1,490 m2 (16,000 ft2). The general excavation extended 9.75 m to 12.5 m (32 feet to 41 feet) below street level with the deepest portions at the central building core mat foundation."

Jan 1, 2017

By F Debidin

The progressive rise of an H-pile during driving of an adjacent pile is described in this case history in which piles 15 to 18 m long were driven to end-bearing for the foundations for a 230 m long building. The use of a reaction beam-soil anchor system for compression load tests is discussed. The results of static load tests to determine pile capacity are compared with those obtained by the Pile Driving Analyzer and by theory. Unusual high temporary compressions were observed by field control staff. Proof testing was necessary to determine the need for restriking of some piles in which rise had occurred.

Jan 1, 2010

By Masahiko Yamaki, Takahiro Yamanashi, Hijiri Hashimoto, Hirochika Hayashi

"In this study, the authors used heat conduction analysis with the aim of quantitatively evaluating whether treating improved ground with cover soil is an effective measure for maintaining strength development in the surface layer of improved ground after constructing cement treated soil for the winter season. This report describes a simple procedure to evaluate covering soil thickness, which is necessary for the strength of the surface of cement treated soil, by using the freeze index and both the water content ratio and dry density.INTRODUCTIONIt was reported that when ground improvement using cement is performed in winter in a snowy cold region (Fig. 1 photo, Fig. 2), the uppermost 1 m of the improved ground (i.e., the cement-treated soil) tends to become prone to solidification failure from exposure to the cold air during curing (Hashimoto et al. 2006). In light of this, our research laboratory conducted unconfined compression tests using curing temperature as a parameter of analysis on improved ground toward understanding the influence of curing temperature (ambient air temperature) on the strength improvement afforded by ground improvement.The authors found that if the curing temperature is maintained at 0°C for the first 28 days after improvement and then at 5°C for the next 337 days after improvement, the improved ground is expected to have 90% of the unconfined compressive strength of improved ground whose temperature was maintained at 20°C for the first 365 days after improvement (Hashimoto et al. 2011)."

Jan 1, 2015

By Amr M. Sallam

A case history of utilizing a mat foundation enhanced with ?settlement-control? piles to support a high-rise building in Downtown Orlando is presented. Original geotechnical engineering studies, performed by others, recommended pile foundations due to difficult soil conditions and highly variable loads. The value engineering study performed by the authors provided alternative foundation system of the mat foundation enhanced by ?settlement-control? piles. The alternative foundation system required few iterations of structural and geotechnical analysis. A target stiffness for the settlement-control piles was selected by the structural engineer. Pile load tests were performed to verify the recommended pile geometry. A total of 81 auger-cast-in-place settlement-control piles 45-foot long 16-inch diameter were installed. A total of 24 columns were monitored for settlement, which showed substantially less settlement than predicted. It is the authors? opinion that the ?settlement-control? piles increased the mat stiffness, relieved the concentration of contact pressures around heavily loaded columns, and reduced potential differential settlement. Mat foundation with settlement-control piles provided border-line foundation solution between shallow and deep foundations and has the potential to be widely used in Central Florida for similar subsoil and loading conditions; however a thorough analysis using three dimensional Finite Element Modeling may be needed to refine the geotechnical evaluations.

Jan 1, 2009

By Robert Thurner, Albin Norrman, Sami U. Raja

The West Link is a double track railway project currently under construction in Gothenburg, Sweden. The project includes the construction of 8 kms of track, 6 kms of which will be in tunnels. Beside several large excavations, three new stations will be built: Centralen, Haga and Korsvägen, all within the city of Gothenburg. The first construction phase of the project began in May 2018, and the finalization of the project is expected in 2026. The project is divided into five sections. Keller is involved in four of these contracts since the design & planning phase in 2018 assisting the special foundation works with various geotechnical techniques including Dry deep soil mixing (DDSM), jet grouting, rock grouting, uplift piles, sheet piling and rock dowels. The core idea behind successful collaboration has been to apply the right product for a location specific challenge which can help optimise costs & time for the project with a minimal environmental impact. Due to the extensive nature of the project, a team of experts from various locations around the world is helping design and execute various foundation technologies and providing solutions to the practical challenges in the project like working close to existing structures, rail lines, river etc.

May 1, 2022

By John S. Pack

The application of square shaft helical piers in expansive soils is a standard of practice in many areas of the United States. Over 20 years of performance monitoring show exceptional performance and economy will result if proper design procedures, specification requirements and installation procedures are followed. This is true for new foundations and the repair of existing foundations, including lightly loaded wood-frame structures on expansive soils. Proper design includes: 1) site geotechnical characterization, 2) pier layout such that each pier is loaded to its maximum design capacity, 3) maximize spans between piers, 4) minimize the number of piers, 5) isolate the structure from the expansive soil with an appropriate void zone below all grade beams, slabs or other components that would otherwise be in soil contact and 6) utilize only single helix piers. Proper specification employs a performance specification that specifies: 1) the design load on each pier with a suitable safety factor, 2) the minimum installation torque, typically 4,000 ft-lbs (5.4 kN-m), or refusal, 3) a minimum pier shaft steel Fy = 70 to 90 ksi (483 to 621 Mpa) and pier helix steel Fy = 80 ksi (552 Mpa), 4) 1.5 to 1.75 inch (38.1 to 44.5 mm) square shafts, 5) smooth shaft surface, 6) the ICC Evaluation Report (ER) number of the manufacturer and 7) the manufacturer ISO 9001 certification for material quality control. Proper installation requires: 1) equipment with sufficient axial compression force (crowd) on the pier shaft so the helix engages the soil and advances to the specified minimum installation torque or refusal, 2) additional specialized techniques for expansive soils and 3) qualified specialty helical pier installation contractors experienced in expansive soils who submit and utilize pier configurations, techniques and equipment that will most effectively and economically meet the specified performance.

Jan 1, 2007

By Craig H. Olson

"A new ship dock at a Philadelphia area refinery will be capable of docking the largest tanker to travel the Delaware River, the Stena V-MAX, which will induce significant lateral loads. The loads at the dock, a system of mooring dolphins and platforms, will be resisted by over 150 pipe piles, including some 20- and 30-in diameter, reinforced, concrete-filled pipe piles and H-piles. Construction included driving the pipe piles to the required ultimate capacity, flushing the pipe pile casing clean of overburden materials, followed by drilling rock sockets into the underlying Wissahickon Formation. The Wissahickon Formation is a complex subsurface that includes variations in depth to bedrock, rock quality, degree of weathering and the presence of very hard quartzite lenses or inclusions. Because of the problematic subsurface, the designers and client requested extensive pile dynamic analysis (PDA) testing by TRC Engineers (TRC).Before beginning, the contractor requested that TRC perform the WEAP (wave equation analysis program) to evaluate the proposed hammer (APE D30-32 open-end diesel) to drive the piles into the proposed bearing strata while maintaining allowable compression stress levels. The WEAP provided a prediction of blow counts and stresses for various ultimate capacities, and showed that for the HP14x89 piles with a required ultimate capacity of 480 kips, a blow count of at least four blows per in at a stroke of 8.0 ft was necessary.New Approachway RampThe PDA testing began at the new dock approachway ramp, parallel to the existing one. The new structure is a 300-ft-long by 21- ft-wide concrete deck supported on seven bents; each has two 24- ft-diameter steel open-ended pipe piles. Every pipe received an HP 14 x 89 x 80-ft pile that was later driven beyond the pipe pile tip to create a composite pile. The pipe piles were later cleaned of overburden materials and finally filled with concrete and rebar. At each bent, a cap was installed on top of each pair of pipe piles, and then a prefabricated concrete deck was added."

Jan 1, 2008

By Luca Pingue, Regine Jagow-Klaff, Franco Muratore, Carlandrea Albonico, Damiano Frontini, Rudolf Wernecké

This paper describes an artificial ground freezing (AGF) application carried out to ensure both watertightness and structural support for the safe excavation of four cross passages of the Forrestfield Airport Link (FAL) project in Perth. The line will deliver 8.5 km extension of the existing urban rail network connecting the growing eastern suburbs of Perth with the existing suburban rail network. The proposed soil improvement technique is adopted as a smart alternative to jet grouting from the surface since the use of heavy equipment with long vertical mast was not allowed due to the line underpassing an airport in operation. In this paper, details of the challenges and lessons learned during both design and construction phases are given. Furthermore, it is described the geometry and the installation of freeze pipes in presence of a massive steel frame, ventilation system and slurry pipes of the tunnel boring machine (TBM) in operation. It is also illustrated the web monitoring system to allow key personnel to follow in real time the development of soil temperatures, tunnel convergences and ground surface deformations as well as changes in the interaction between international parties involved due to the COVID-19 pandemic.

May 1, 2022

By Leo Panian, Ryan Nagle, Priyanshu Singh, Gina Carlson, Wayne Magnusen

"This case study presents the design and construction of an integrated foundation and ground improvement solution utilizing deep soil mixing (DSM) and micropiles. 270 Brannan is a midrise office building in San Francisco that straddles the historic shoreline that was reclaimed in the 19th century. Subsurface conditions include shallow bedrock inland of the historic shoreline, and steeply dipping bedrock overlain by 60 feet of compressible deposits and liquefiable fill on the bay side. Project challenges included mitigating the liquefaction and lateral spreading hazards, addressing settlement concerns in the fill and the bay deposits, developing a cost-effective foundation support solution, assuring satisfactory seismic performance, and addressing construction restrictions with existing adjacent structures.DSM combined with micropiles was identified as the most cost-effective solution for the ground conditions. The DSM panels act both as a liquefaction mitigation mechanism and a foundation support system. Resistance to seismic overturning is provided by uplift-resisting micropiles. The DSM-micropile solution allows the use of efficient conventional spread footing foundations, integrating isolated micropile groups to anchor the shear walls. Successful installation of the system relied on a program of field testing to validate the design and conformance with the design criteria.INTRODUCTIONThe regular grid of surface streets within San Francisco’s South of Market (SOMA) district provides little evidence of the geotechnical complexities that lie below. In the late 1800s, sand dunes, bedrock hills, cliffs, marshes, and mud flats were flattened and filled, concealing their locations and characteristics. The 1906 San Francisco earthquake and fire leveled many buildings in SOMA; new buildings were built after 1906 – often on top of rubble and debris from the structures that came before. Locally, the combination of natural geology and historical interventions can produce complex subsurface conditions that vary dramatically over short distances. This is particularly true at locations where tidal mudflats once met bedrock hills at the shore of San Francisco Bay.This case study describes an integrated foundation and ground improvement system implemented for a multistory “Class A” office building at a complex SOMA urban infill site. The system utilizes cement deep soil mixing (DSM) in combination with spread footings and micropiles to address a range of design and construction issues, including liquefaction and lateral spreading mitigation; consistency of earthquake ground motions; shallow foundation support; seismic uplift resistance; and avoidance of loading adjacent basement walls. The system was implemented by a technically-sophisticated owner through a process that included constructive collaborations between the project geotechnical engineer, structural engineer, general contractor, and specialty foundation and ground improvement contractor(s). The system is designed to cost-effectively provide a high level of seismic performance."

Jan 1, 2017

By Richard Schmidt, Lijun Deng, Mohamed Abdelaziz, Weidong Li

Helical piles are widely used as a foundation supporting a variety of different structures. Understanding the axial behaviour of helical piles is required to confirm the engineering design. Helical pile research is often conducted in the field, but this method can be prohibitively expensive in some cases. Geotechnical centrifuge modeling offers an alternative method for the helical pile research and practice. A series of axial load tests of helical piles installed into cohesive soils were conducted on the geotechnical centrifuge at the University of Alberta. The objective was to investigate the effects of inter-helix spacing and soil strength on the axial behaviour of helical piles. Four types of aluminum model helical piles including one single-helix pile and three double-helix piles with various inter-helix spacing ratios were tested. Both compressive and tensile loading tests were conducted. All model piles were instrumented with multiple strain gauge stations. The clay had an undrained shear strength of approximately 50 kPa and 120 kPa. The test results indicate that there is a transitional failure mode between the two widely recognized failure modes, i.e., individual plate bearing and cylindrical shearing. The shaft adhesion was significantly reduced by the helix. Axial capacities were comparable to the field test results.

By Thomas W. Scott, Manh N. Tran

Marine environments present a range of challenges for pile construction. This paper contains a discussion on the design and construction of marine piles for a recent Toll Shipping wharf upgrade in Burnie, Tasmania. The project involved several new structures including mooring, berthing and ramp dolphins supported by driven tubular piles with rock sockets, and an onshore mooring dolphin and ramp abutment supported by bored piles. Through the project, a range of construction challenges were experienced, including availability of tubular piles, the different penetration depths of driven piles into rock, the ability to drill out sockets when the piles were raked, the difficulty in verifying the design intent, latent conditions and ship impacts. The paper will present a summary of the different factors that influenced design concepts for the structures involved in the upgrade, and the challenges involved in the design of the structures. Following this, the paper will describe the methodology used to verify the design (including a pullout test), observations made during pile construction and lessons learned on how to limit risk throughout construction.

Nov 1, 2022

By Mohammed Faizal, Abdelmalek Bouazza

"The operation of ground source heat pumps combined with foundation piles can have an effect on the thermal behaviour of the pile and the surrounding soil. This paper presents the effects of continuous heating, continuous cooling, and alternate heating and cooling operations on ground and pile temperatures as well as the thermo-mechanical behaviour of a field scale energy pile. The effect of pile operation on the ground temperatures is highest near the pile and reduces with increasing radial distance. The results of the present studies generally showed that the thermal elasticity of the pile is not affected.INTRODUCTIONGeothermal energy piles are foundation piles used as underground heat exchangers to maintain thermal comfort in buildings, via the use of ground source heat pumps (GSHPs). Ground source heat pumps are more economical and environmental friendly compared to conventional heat pumps. Energy piles can be combined with supplemental surface heaters or coolers, known as hybrid systems, for forcefully recharging the ground during non-operational times of the GSHP. Alternative heating and cooling of the GSHP improves geothermal energy usage and alleviates heat build-up in the ground and provides a balance of ground temperatures around the heat exchanger (Jalaluddin and Miyara, 2012).The temperatures induced in the piles during GSHP operation can lead to a complex response of thermal strains and stresses in the pile concrete. An assessment of the thermo-mechanical response of energy piles for various thermal loads may assist engineers in the design process. Furthermore, an assessment of ground temperatures will also highlight any potential thermal interactions with other energy piles in actual building operations.At present, the thermal strain and stress distribution in field scale energy piles has mostly been studied for continuous operation (Laloui et al., 2006; Bourne-Webb et al., 2009; McCartney and Murphy, 2012; Akrouch et al., 2014; Mimouni, 2014; Murphy and McCartney, 2014; Murphy et al., 2014; Wang et al., 2015). These studies have contributed considerably to the understanding of the axial thermal strain and stress distributions in the piles and have shown that pile thermal behaviour is mostly thermo-elastic without inducing major structural concerns.The present paper adds to the current knowledge by assessing the pile thermo-mechanical and ground thermal response for continuous and alternating thermal loads of a field scale energy pile. The operation modes studied are 24 hours continuous cooling (Faizal et al., 2015), 24 hours continuous heating, (Wang et al., 2015) and alternate heating and cooling operation (Faizal and Bouazza, 2016). The forced ground thermal recharging is done during the non-operating times of the cooling unit, simulating a solar hybrid GSHP system for a scheduled intermittent mode of operation."

Jan 1, 1900

By Lori A. Simpson, Linda H. Liang

A high-rise building, consisting of two tower structures occupying the entire site, is in construction in San Francisco. The North Tower will consist of 12 and 35 stories above a one-level basement. The South Tower will consist of 9 and 22 stories over one partially below-grade level of common space; a portion of the South Tower will have a three-level basement. The towers will be supported on mat foundations bearing on native very dense sand in the footprint of the threelevel basement and on ground improved with soil-cement mixed (SCM) panels that extend through loose sand and marsh deposits into very dense sand. Shoring systems for the basement excavations include cantilevered and tiedback soldier-beam-and-lagging systems and SCM cutoff walls. Subsurface conditions include loose fill and Dune Sand and loose and soft marsh deposits overlying very dense sand of the Colma formation. Groundwater is approximately 15 to 22 feet deep; the three-level basement extends below groundwater. The site is on Market Street in San Francisco, with SF Municipal Railway (MUNI) and Bay Area Rapid Transit (BART) tunnels running below Market Street approximately 45 and 36 feet north of the site, respectively. Both tunnels are 16.5 feet in diameter. The top of MUNI and BART tunnels are 25 feet and 63.5 feet below street grade, respectively. BART has stringent requirements regarding construction adjacent to their facilities, including disallowing adding pressure to their tunnel, lowering groundwater by more than two feet, and vibrations from construction activities. Design of the shoring and the foundations within the BART zone of influence were subject to their design requirements. The project was also subject to a peer review, as required by the San Francisco Department of Building Inspection. We used FLAC to evaluate stresses at the BART and MUNI tunnels and on the SCM panels. This paper will present the mitigations needed to address seismic hazards and BART restrictions and to provide adequate foundation support for a tall building with high seismic loads.

Jan 1, 2017

By Lori A. Simpson

A high-rise building, consisting of two tower structures occupying the entire site, is in construction in San Francisco. The North Tower will consist of 12 and 35 stories above a one-level basement. The South Tower will consist of 9 and 22 stories over one partially below-grade level of common space; a portion of the South Tower will have a three-level basement. The towers will be supported on mat foundations bearing on native very dense sand in the footprint of the three-level basement and on ground improved with soil-cement mixed (SCM) panels that extend through loose sand and marsh deposits into very dense sand. Shoring systems for the basement excavations include cantilevered and tied-back soldier-beam-and-lagging systems and SCM cutoff walls. Subsurface conditions include loose fill and Dune Sand and loose and soft marsh deposits overlying very dense sand of the Colma formation. Groundwater is approximately 15 to 22 feet deep; the three-level basement extends below groundwater. The site is on Market Street in San Francisco, with SF Municipal Railway (MUNI) and Bay Area Rapid Transit (BART) tunnels running below Market Street approximately 45 and 36 feet north of the site, respectively. Both tunnels are 16.5 feet in diameter. The top of MUNI and BART tunnels are 25 feet and 63.5 feet below street grade, respectively. BART has stringent requirements regarding construction adjacent to their facilities, including disallowing adding pressure to their tunnel, lowering groundwater by more than two feet, and vibrations from construction activities. Design of the shoring and the foundations within the BART zone of influence were subject to their design requirements. The project was also subject to a peer review, as required by the San Francisco Department of Building Inspection. We used FLAC to evaluate stresses at the BART and MUNI tunnels and on the SCM panels. This paper will present the mitigations needed to address seismic hazards and BART restrictions and to provide adequate foundation support for a tall building with high seismic loads.

By Terence P. Holman

Micropiles are employed to retrofit existing foundations, including underpinning prior to future construction operations and resupport of existing structures that have experienced distortion and settlement. This paper presents analyses of the two case histories requiring the use of micropiles in these applications. The first case history involves micropiles used to resupport a settled pump station next to an excavation which had suffered basal failure and ground loss. A compression load test pile experienced plunging failure which, after analysis of the strain-gauge data acquired during the test, was attributable to a greater degree of disturbance to the subsoils beneath the site than anticipated. After construction of the micropiles around the pump chamber a synchronized jacking system was used to lift and right the 320 kip chamber structure, followed by resupporting it on the newly constructed piles. The second case history entails the use of micropiles for direct underpinning support of existing columns prior to a utility tunnel installation within an existing high-bay warehouse structure. The design constraint that most significantly affected the successful completion of this project was the desire to bond the new piles into the existing reinforced concrete foundations. As a result of the coring method through the footing, the ultimate bond stress measured during a pullout test was more than twice that assumed in the design. Monitoring of the underpinned columns during trench excavation indicated that the system performance was acceptable. These case histories reinforce the concept that lower capacity micropiles can provide a rapid means to underpin and retrofit existing structures.

Jan 1, 2007

By Richard Berry

The spacing of grout injections is typically about 2 to 2 V½ meters if the purpose of the grouting is densification of the in-situ soils. Hole spacing will vary with the in-situ soil properties and the grout injection rate; faster rates requiring closer hole spacing.

Feb 10, 2003