Search Documents

Ni and samaria-doped ceria (Ni-SDC) cermet are desirable materials for making a solid oxide fuel cell anode working at intermediate temperature (800°C or lower) due to its good ionic/electronic conductivity at the reduced operating temperature. An advantage of the use of a Ni-SDC anode is the enlargement of the effective reaction zone in the interfacial area between the anode and the electrolyte. As a result of the mixed ionic/electronic conductivity of the anode, the electrode reaction rate is enhanced. Investigations into the properties of the ceria-based anode reveal that the performance of the anode is closely related to its microstructures, which are dependent on the composition and fabrication conditions of the ceramics. In this paper, a method for quantitative characterization and correlation of Ni-SDC cermet microstructures to the performance of an anode is investigated. A series of Ni-SDC anode samples are prepared by screen-printing (SP) and spin-coating (SC) techniques, and different microstructures of the samples are obtained through controlling the SP or SC conditions and the sintering temperature. Individual phases (Ni, SDC and pore) in the tri-phase boundary (TPB) microstructures in the electrode are differentiated and segmented from each other in optical and SEM images based on the differences in refractivity and atomic contrasts among the phases. The geometric properties of the segmented phases are characterized using image analysis methods, so that a quantitative skeleton illustrating the TPB microstructures of the Ni-SDC electrode is obtained. Statistical analysis of the distribution of the three phases in the TPB microstructures is performed and the relationship of the microstructures with the optimum electrode is interpreted in terms of the microstructure analysis data.

Jan 1, 2005

By A. Gillis

"In order to obtain the equipment necessary to automate the equipment it was decided that the Department of Mines and Milltronics would jointly survey the circuit. This survey involved a metallurgical study by the Department of Mines and Milltronics took sound recordings during manual operation, checking in circuit bottle necks and determining the number of sensors that could be applied.The conveyer is driven by 2 PIV drives, each has a variable speed of 3/ 1. The cross conveyer that feeds directly into the rod mill feed chute will contain an automatic sampler and will eliminate the necessity of stopping the belt feeders to take samples. At present, hourly samples are taken from this point and the circuit is upset and cycling results.The Adequate scale is very close to the rod mill to totalize and thereby give a continuous indication and the second purpose is to take a signal from it and control the solution addition to the rod mill.A pneumatic positioner was obtained and put on the scale which produces a 3 tp 15 psi signal which is proportional to the actual tonnage going across the scale. This signal was fed to a bias loader which was mounted on the control panel. From there the operator can set the amount of solution that is wanted by the rod mill. No matter what the feed rate is, the signal coming from the bias loader will follow it automatically. This in turn goes to the pneumatic solution valve (1 ½” ) and the solution goes in with the feed to the rod mill. This is only part of the solution required for dilution since the rest of it is used as a force jet for the feed to the rod mill."

Jan 1, 1965

Cameco Corporation is in the process of revitalizing the Key Lake mill. As part of this process, the company is considering installing the Rabbit Lake style strong acid stripping in solvent extraction. This would lead to using hydrogen peroxide for uranium precipitation. The process currently employs ammonia stripping and ammonia precipitation. As part of the process evaluation, an indirect fired drier pilot plant test was conducted. This paper will discuss the results of that test work, including the relationships between the following: ? Drying temperature and product grade ? Drying temperature and product colour ? Drying temperature and product reactivity with water ? Drying temperature and energy input requirements ? Drying temperature and shipping costs

Aug 1, 2010

By L. V. Bell

"The gold deposits of the Caribou mine are representative of those of the Province of Nova Scotia as a whole. The ore shoots within the deposits, in common with those elsewhere within the Province, are associated usually with interruptions or irregularities in the broader and uniform fold structures. The structural factors localizing ore deposition as applied more specifically to the Caribou mine are demonstrated chiefly by the close relationship of the two principal ore shoots, known as the main orebody and the 'high-grade' vein, with a pitching drag fold developed in the southeast limb of the major northeast-southwest trending anticlinal fold or elongated dome that constitutes the primary structural feature of the Caribou gold district. It is of interest to note that the evidence indicates that this drag fold, in common with other folds subsidiary to the primary fold, formed as a result of movement similar in nature to that which caused the primary fold itself. Presumably, therefore, these folds are coincident in time.The property described here as the Caribou mine is an amalgamation of two adjacent properties formerly known as the Ross and the Nova Scotia Gold, but which since 1934 have been controlled and operated as a unit by The Consolidated Mining and Smelting Company of Canada, Limited. The Caribou mine is situated in the Caribou gold district about 45 miles to the northeast of the city of Halifax and about 6 miles to the north of the Moose River gold district.The history of mining at Caribou dates back to 1867. The first recorded gold production is for 1869. From 1869 to 1933 the gold produced from the mines of the Caribou district aggregated 47,249 oz. from 93,234 tons of ore treated. The grade of the ore on the basis of the gold actually recovered from the district would thus average 72 oz. gold a ton, which, as will be noted from the following, is precisely the grade of the ore treated from the Caribou mine during operations by The Consolidated Mining and Smelting Company. These operations commenced in September, 1934, and milling on a commercial basis was under way during 1938. Since that time production, apart from a short period in 1945 during which efforts were concentrated on development work, was continuous to early in 1947, when the mine closed down owing to exhaustion of the known orebodies. Gold produced from the Caribou mine by The Consolidated Mining and Smelting Company from September, 1934, to the close of 1946 aggregated 43,205 oz. from 90,754 tons of ore milled; the grade of ore treated averaged 0.50 oz. gold a ton. The indicated average grade of O.S oz. gold a ton for the ore of the Caribou district throughout its mining history ranks somewhat higher than the 0.37 oz. a ton average for the ore milled to date from the several gold districts throughout the Province as a whole according to the production statistics of the Provincial Department of Mines."

Jan 1, 1954

By Z. S. Abisheva

The Zhezkazgan copper sulfide ore deposit in Kazakhstan contains both rhenium and the rare osmium isotope "osmium-187" (187Os) in the high isotopic purity of 99.4 ± 0.2%. This isotope is believed to have originated as a result of the disintegration of one of the rhenium isotopes, according to the reaction: 187Re75 ?> 1870576 + B- + v~ (where B is a 13-particle, v~ is a 3-disintegration antineutrino). The distribution of osmium and rhenium in metallurgical byproducts produced during the recovery of copper from these ores has been studied and process flowsheets for the processing of rhenium and osmium-containing byproducts have been developed.

Jan 1, 2007

By Peter McBride

Human excellence in all areas of endeavour is acknowledged and recognized. Establishing role models and spreading the word on best practices helps broader audiences. For on-the-job safety, recognition awards are a component of successful programs. In Canada?s mining industry since 1941, the John T. Ryan Safety Trophies initiative has contributed to the sector?s improving record in this area. The much sought after and rich in history John T. Ryan trophies are recognized symbols of safety excellence in Canada. The effectiveness of the Ryan safety recognition program in Canada has led to its export to other mining countries seeking to improve their overall safety performance.

May 1, 2008

By M. Cimenti

Fuel cells have tremendous potential as power sources but much fundamental research is still required. One key component of the research is the experimental set-up used. In particular, the placement of the reference electrode is extremely significant in measuring the half-cell overpotential of solid oxide fuel cells, since differences in area, misalignments, and also differences in the kinetics of the working and counter electrodes can cause both scaling errors and frequency distortions of the measured impedance. The impedance of thin solid electrolyte cells of different electrode geometries has been calculated using the finite element method and the results compared to experimental values obtained for the oxygen reduction reaction on platinum.

Jan 1, 2005

By J. H. Baek, D. W. Lee, B. K. Kim

Nanostructured Cu-Al203 composite powders were synthesized by thermochemical process for an electrode application. The synthesis procedures are 1) preparation of precursor powder by spray drying of solution made from copper and aluminum nitrates, 2) heat treatments to evaporate volatile components in the precursor powder and synthesis of nanostructured CuO+Al2O3, and 3) CuO reduction by hydrogen into Cu. The suggested procedures stimulated the formation of the gamma-Al2O3. The mean particle size of the final composite powders was 20nm, and the electrical conductivity and hardness in the hot-extruded bulk were competitive with Cu/Al2O3 composite by the conventional internal oxidation process.

Jan 1, 2004

By A. Cadieux, J. -B. Pineault, C. Allaire

The temperature measurement of the molten metal in the aluminum transformation process is of prime importance. This is particularly the case for aluminum treatment furnaces, such as holding and melting furnaces. Such reverberatory type of furnaces involve a thermal gradient across the metal line which limits the life of conventional thermocouple protective ceramic shields, due to the action of locally induced thermal stresses. This paper presents a novel thermocouple assembly using a composite refractory protective shield allowing long term resistance to such above conditions. Example of results obtained from various tests in aluminum holding furnaces are presented. The results confirm the superiority of the novel thermocouple assembly, as compared to conventional thermocouple units.

Jan 1, 2004

By J. H. Baek, S. Alexandrovskii, D. W. Lee, B. K. Kim

Nano-phase titanium carbide was synthesized by Mg-thermal reduction process using a novel route of Mg-thermal reduction. The processes are based on I) feeding of TiC14+CxC14 x = 1, 2 ) solution into liquid magnesium, 2) Mg-reduction of metal chlorides, 3) TiC formation by the reaction of released Ti and C atoms, and 4) vacuum separation of residual liquid phases of Mg and MgCl2. In this study, the process for titanium carbide production with composition close to stoichiometry and the minimum content of impurities was optimized with the various process parameters such as concentration of initial solution, its feeding rate and reaction temperature, as well as a kinetic study.

Jan 1, 2004

By G. Brooks, M. Hamed, S. Nightingale, K. Coley

The Marangoni effect plays a significant role in slag line corrosion of refractories. Previous experimental studies for various refractory /slag systems and mathematical models are reviewed and show that Marangoni flow is important in slag line corrosion under static conditions. Recent work by the authors is presented which also shows significant slag-line corrosion of MgO refractory in SiO2-CaO-FeOx-MgO slag. The rate of attack of the MgO was marginally slower in the case of slags containing alumina. A semi-empirical model developed by Hrma based on mass transfer control described reasonably well the observed progression of corrosion with time. Further work is proposed to evaluate this model.

Jan 1, 2004

By T. Cutard, H. Marzagui, E. Ouedraogo, M. Roosefid, M. Prompt, C. Deteuf

The present work is achieved in the framework of a French national program on modeling and experimental characterization of the thermo-mechanical properties of refractory materials (PROMETHEREF). This research program is aimed to establish fair models and experimental database and to make it available to industrial partners for numerical simulation of industrial structures made of these materials. The present paper focuses on two silica-alumina refractory castables, an andalusite based one and a bauxite based one. We will present the first rheological characterization results achieved at room on normal and preheated samples of these two refractory castables. Refractory castables are characterized with the help of four points bending tests, compression tests and tensile tests.

Jan 1, 2004

By J. A. Haskin

The Engineering Department at Flin Flon has the following responsibilities: 1. Underground Surveying. 2. Open-Pit Surveying and Supervision of Blasting. 3. Mine Geology and Examination of Prospects. 4. Design of Plant Additions and Improvements. 5. Miscellaneous Field W ork, Reports, etc. The entire surface plant, as well as the underground workings, are located by co-ordinates based on a triangulation system covering an area approximately one mile long by one-half mile wide. The origin of this system and one end of the base-line is the southwest corner of Township 67, Range 29, west of the Principal Meridian. The bearing of the base-line was determined from the township boundary, which runs true north, so that all other bearings are almost astronomical. This is a great convenience when our surveys must be tied to mineral claims, rights-of-way, and land subdivisions. As the base-line extends across Flin Flon lake, its measurement across smooth ice was simple and accurate. The length, slightly over 1,600 feet, has been adjusted for the temperature and tension of the standard tapes used and checked sufficiently to ensure a maximum error of 1 : 15,000. Each angle was repeated ten times, but as no special refinements were used, errors of as much as four or five seconds are possible. The elevation of the origin of the triangulation system was approximately 1,050 feet above sea level. The use of this true elevation in our surveys would have resulted in negative elevations underground as soon as the mine reached a depth greater than 1,050 feet. To avoid this complication we therefore added 4,000 feet to this elevation. The collar of the Main shaft, for example, which is actually 1,072 feet above sea level, appears in our records as at elevation 5,072. Underground surveying, which follows standard practice, is done by two mine surveyors who share three helpers. The meridian is taken underground from two wires hung in either of the two vertical shafts.

Jan 1, 1935

By T. Melfi, M. James

Attaining required mechanical properties in welds made using the double submerged arc welding (DSAW) process is difficult, and it is becoming more difficult as the strength level of the base materials continues to increase. Producing weld metal with adequate mechanical properties involves factors that are often overlooked and not taken into consideration. Not least amongst these problems is simply finding information to use in selecting the appropriate flux/wire combination. Most of the available data on flux/wire combinations provided by consumables manufacturers is generated using the multiple pass welding procedures required for classification per specifications such as AWS A5.17 and A5.23. This data really gives no insight into the properties that can be expected in a DSAW application. Also, base plate composition plays a very significant role because of the fact that base plate dilution can be as high as 70% in DSAW welds. This means that if any elements are present in the base metal that are deleterious to mechanical properties, they will also be present in significant quantities in the weld deposit. Some of these elements can decrease toughness and increase hardness (increased hardness is a concern if the pipe is intended for sour service). Some of these problems can be mitigated by proper selection of welding consumables. Selection of proper welding consumables means selecting an electrode that provides the appropriate alloying elements to obtain the desired level of impact toughness while also keeping the hardness within any specified limits. In order to attain the necessary impact toughness, selection of a flux with an appropriate composition (in terms of its basicity and its ability to control the nitrogen content of the weld deposit) is required. As with all welding processes, the mechanical properties of DSAW welds are also highly dependent on the welding procedures. This work clarifies how to select appropriate consumables to meet a given set of requirements, and also how to achieve the optimum mechanical properties from those consumables.

Jan 1, 2005

By Lei Pan, Roe-Hoan Yoon

"Sea water flotation is becoming a reality due to shortages of fresh water. To better understand the mechanisms involved in sea water flotation, we have studied the effects of KCl and MgCl2 on the surface forces present in the wetting films of water formed on hydrophobic surfaces. The measurements have been conducted using the force apparatus for deformable surface (FADS), which is capable of measuring both the surface and hydrodynamic forces responsible for bubble-particle interactions. The results obtained with the gold surfaces hydrophobized with butanethiol (C4SH) show that the wetting films of Ultrapure water do not rupture despite the relatively high water contact angle (??= 80o) and the presence of a long-range hydrophobic force with a decay length (D) of 25 nm in the film. The film is metastable with its equilibrium thickness (he) at 140 nm, where the repulsive double-layer force is equal in magnitude to the capillary force as shown in Figure 1. The film loses its metastability and ruptures in a 10-2 M KCl solution, in which the double-layer force decreases substantially due to the decrease in Debye length (?-1) while the decay length of the hydrophobic force remains as large as 23 nm.The effects of MgCl2 has also been studied using a C4SH-coated gold surface with a water contact angle of 87o. It has been found that in a 10-4 M solution double-layer force decreases due to the decrease in the negative ?-potentials and Debye length, which should help destabilize the wetting film. However, the film remains stable due to the decrease in the decay length of the long-range hydrophobic force from 45 nm in Ultrapure water to 14 nm in the MgCl2 solution. Thus, the results obtained in the present investigation support the view that the difficulties in sea water flotation may be due to the presence of MgCl2 rather than the presence of NaCl in sea water (Ramos, et al., 2013)."

Jan 1, 2016

By Y. Kocaefe, S. Afshar, D. Kocaefe, Z. Kunt, C. Allaire

Interaction of aluminum with silica based ceramics Jose M. Soto, Jeffrey D. Smith, William G. Fahrenholtz. Department of Ceramic Engineering University of Missouri-Rolla Rolla, MO 65409-0330 USA ABSTRACT Interactions between A356 aluminum (Al-Si alloy) and dense fused silica (FS) riser tubes used for low-pressure casting of aluminum alloys were evaluated using a sessile drop approach. The tubes have a short service life, but cost and thermal shock resistance make them an effective solution. The main problem encountered during use is the reaction of aluminum with silica to form alumina and silicon, which causes failure. Tests have been conducted on as-fired (uncoated) and modified (coated) tubes. Experiments were carried out in a horizontal furnace at 1225°C under argon to minimize the effect of the aluminum oxide on the interactions at the alloy-silica interface. Images of the drop were acquired and contact angle values were estimated for uncoated and coated samples, but no significant differences in the contact angles were observed. Scanning electron microscopy revealed the presence of cracks at the interface between the reaction zone and the unreacted silica. The presence of reaction products (silicon in the reacting alloy and aluminum in a reaction zone between the alloy and the unaffected silica) has been confirmed using energy dispersive spectroscopy. A two layer coating system was found to be effective in reducing penetration of the aluminum alloy. The interactions between bed media and aluminum have been studied under static and dynamic flow conditions. An experimental system was set up simulating a small filter. Desired flow field can be created around alumina particles and velocities can be adjusted. A mathematical model was developed to predict the velocities, and this was validated using data from a visualization study. The interaction zone on the surface of the particles was analyzed with optical microscopy and SEM. This paper presents the study and compares the results under static and dynamic flow conditions.

Jan 1, 2004

By R. V. Typliski, G. J. Labarre

"Hudson Bay Mining and Smelting Co., Limited, Flin Flon, Manitoba, has developed a metallurgical wastewater treatment system employing two-stage lime neutralization, sludge recirculation and conventional mechanical thickening.Laboratory investigations, initiated in 1970, led to the construction of a pilot-scale minewater treatment plant, at Schist Lake Mine, in early 1971. This plant, treating 600 cubic metres /day of wastewater containing 30-60 mg/1 zinc. demonstrated metal extraction efficiencies of 99% under normal operating conditions.On the basis of this pilot work, a second pilot-scale treatment system was established in 1975 at the Flin Flon metallurgical plant to treat zinc refinery process waste water. Through numerous improvements, including automatic con¬trol equipment, the system has evolved to a full-scale operation capable of treating 800 cubic metres/day of wastewater containing 4-11 gm/1 zinc. Treated effluent contains 0.2-20 mg/1 zinc. The hydroxide sludge produced returns to the metallurgical process for the recovery of metals while clarified effluent discharges to waste.With the system, Hudson Bay Mining has achieved its original goal: the reduction of environmental contamination, while realizing a return from metal recovery.IntroductionWith the goal of reducing environmental contamination, Hudson Bay Mining and Smelting began laboratory testwork, during the late 1960's, into the methods and technology for neutralizing and removing heavy metals from acid mine drainage. Based on lime treatment, early tests showed much promise and culminated in the construction of a pilot-scale test plant at Schist Lake Mine in early 1971.This pilot system utilized technology developed in laboratory studies, and related to work then underway by state authorities in Pennsylvania coal mines. The basic operation consisted of a lime slurry tank, baffle reactor and a free-settling basin. Through three summers of operation, the Schist plant, capable of treating 600 cubic metres/day of minewater, produced a heavy-metal extraction of 99% under normal conditions. Although successful in proving the treatment chemistry, the plant displayed deficiencies in sludge densification and handling."

Jan 1, 1980

By V. Pouyafar

Semi-Solid metal alloys, as used in SSM processing, have a special microstructure of globular solid particles suspended in a liquid matrix, which makes them behave differently in forming processes. The sensitivity of semi-solid slurries to temperature variations and their history and rate dependant behavior, make process design and control difficult. Precise selection of the process parameters is necessary in part production. Therefore, a numerical analysis and simulation of the process can be a valuable tool in process design. In this work we proposed a structural dependent model to account for the thixotropic behavior of semi-solid metals. The parameters of the model were then determined using rheometery tests. The results show a good agreement between the model and the experiments.

Oct 1, 2011

By M. Hosseinzadeh

By changing the quality of consumed refractory bricks in burner zone of sarcheshmeh copper complex anod kiln removing of carbon precipitation phenomenon was studied. For blister deoxygenation LPG is blowing in anod kiln and cause destoring microsturcture and bonding of refractory bricks. Studies are shown that in a part of the bricks which have a temperature of 800 - 1000 °C , iron content phases in magesia - chromite bricks are like catalist and cause increasing the rate of carbon precipitation reactions . In a way that in comparsion of two bricks with best and medium quality with different analysis, this problem is more critical in best quality bricks containing high iron oxide. Therefore special magesia spinel bricks suggested and installed in burning zone.

Jan 1, 2004

By M. R. Coffin

In recent years, improved operation of the Kidd smelter has resulted in an increase in blister production capacity. Due to manpower and equipment limitations anode production and treatment rates could not be increased without incurring significant additional operating expenses. The option chosen to expand casting and refinery capacity to meet the available blister supply was to increase the anode thickness while maintaining the same anode exchange cycle in the refinery. This has resulted in a cathode production increase of almost 10% for minimal expenditure. Equipment and process modifications required to cast and refine the thicker anodes are discussed in this paper, along with the Six Sigma methodologies used to identify them. Key areas covered are Hazelett continuous caster operation, refining process parameters, plating performance and cathode quality.

Jan 1, 2007