Search Documents

By M. Leroux, S. R. Rao, J. A. Finch

"Poor Pb/Zn selectivity during Pb flotation in laboratory tests on a Mississippi Valley-type Pb/Zn ore was traced to a pH effect. In the pH range 9.5-11 sphalerite floated readily without copper activation. Compared to sphalerite flotation with copper activation this procedure gave equivalent selectivity but reduced flotation rate.Possible mechanisms of this sphalerite flotation without copper activation are discussed. Activation by Fe(OH) 2 is suggested, the Fe++ions being derived from superficial oxidation of pyrite in the ore.INTRODUCTIONGalena and sphalerite commonly occur together. The usual practice is to float galena first followed by the flotation of sphalerite after activation with copper (II) sulphate. If ores contain pyrite it is depressed by maintaining an alkaline pH (9- 10) and using NaCN as depressant.In flotation tests with a Pb/Zn ore from Polaris selective flotation of galena could not be achieved consistently as a considerable amount of sphalerite, even though unactivated, floated. A systematic study was carried out to determine the cause of this problem. This led to the unexpected finding that sphalerite floated in the alkaline pH range 9.5-11.0 without preactivation with Cuso 4 . This paper describes the results of this study and discusses a possible mechanism of the flotation of sphalerite."

Jan 1, 1987

By P. J. Foster

Bowtie analysis has recently emerged as a technique of choice that can be used when looking specifically at major hazards in the mining industry. A Bowtie diagram is a graphical means of assessment that focuses on identifying all the specific causes and consequences of major events, from which all the ?pre-event? and ?post-event? control measures can be identified. From this critical control measures can be identified and monitoring/assurance systems can be established. It is this assessment of control measures and their effectiveness that replaces the more traditional evaluation of risk (using matrix-based approaches) based on the fact that risk is a function of control ineffectiveness. This is a major difference with traditional risk assessment where all too often control effectiveness is assumed. This paper summarises the Bowtie analysis process and outlines one specific case study where the technique was used on the unwanted event of a collision of a haul truck and light vehicle in an openpit mine. Although more effort is required in undertaking the assessments, control assurance provided this way will go a long way in ensuring that risk assessments and major hazard management become much more effective in practice.

Aug 1, 2013

By Patrick Laflamme, Jean-François Boulanger

Les minerais de cuivre sulfurés, qui représentent 80% de la production mondiale de cuivre, imposent une étape de concentration des minéraux, premièrement pour atteindre une teneur en cuivre minimale qui permette le traitement pyrométallurgique, mais aussi pour limiter la présence d’élément pénalisants (délétères). Cette introduction offre un survol des principes, limites et pistes d’améliorations touchant la concentration des minéraux de cuivre.

May 2, 2024

By Denis Bois

La Bolivie est un pays en développement qui compte une tradition minière qui précède même l?établissement espagnol en Amérique. Pendant toutes ces années, l?exploitation minière s?est faite sans grands égards pour l?environnement. Au cours des dernières années cependant, le gouvernement bolivien a modifié ses lois afin de rendre nécessaire la prise en compte de l?environnement dans le processus d?exploitation d?une mine. Dans le cadre d?un projet MRN-ACDI1 visant à renforcer le secteur minier en Bolivie et ses retombées pour la population, l?URSTM2 a été mandaté pour développer et mettre en place un programme académique de gestion environnementale minière, basée sur l?expertise canadienne. Ce programme vise à renforcer les institutions académiques boliviennes responsables de la formation en environnement minier en Bolivie ainsi que les ministères et agences gouvernementales concernées.

May 1, 2001

By Lawrence Devon Smith

"The Management and Economics Society has undertaken a survey of industry practice in the evaluation of mineral projects. The survey addresses a number of issues relating to evaluation techniques, discounted cash flow methodology, and risk. Completed during the spring and summer of2005, the results provide a record of opinion at an active and vital time in our industry.The 2005 survey questionnaire was distributed by e-mail to groups and organizations around the world. There were 22 respondents out of several hundred questionnaires distributed (we gather this small proportion of respondents is typical for such surveys). The responses, although a small number, show a consistency that suggests that the survey has captured the views of the industry. The results of the survey are summarized below in series of tables and graphs.The reader is cautioned that the results are a snapshot of industry practice at a point in time as represented by a small sampling of the industry's practitioners. These results should be viewed as indicative values."

Jan 1, 2003

By T. M. Ahmed

Sherritt International Corporation experienced corrosion failures with the 316L stainless steel tubing in a high-pressure still condenser employed for ammonia recovery. A detailed failure analysis was conducted on the condenser tubing to determine the mode and the root cause of the failure. The analysis included both optical and scanning electron microscopy (SEM) of the inner and outer surfaces of the tube as well as characterization of the corrosion products using energy-dispersive X-ray spectroscopy (EDX). Results revealed that the corrosion attack was confined to the first ?100 mm of the tubing at the inlet where the tube was connected to the top tubesheet. The tube suffered both external stress-corrosion cracking (SCC) and crevice corrosion from the shell side (water side), and wall thinning of the inner surface (the tube side) due to erosion corrosion. It was evident that failure of one of the tubes occurred due to SCC that penetrated the whole wall thickness and resulted in a leak failure. Some prevention measures are proposed to avoid this type of corrosion attack in the future.

Jan 1, 2005

By A. Plumtree

The morphology of environmentally assisted cracks in stressed pipeline steel has been investigated. For a dilute and neutral solution (NS4) simulating ground water in contact with the steel, semi-elliptical cracks grow faster on the surface (2c) than in the depth (a), hence, the aspect ratio (a/c) decreases. This is explained using a deterministic concept since corrosion is dominant and the primary constraint is the conservation of charge. By contrast, when mechanistic conditions prevail, significant growth occurs in the depth. When underloads are imposed in the loading history, temporary accelerations in crack growth occur because corrosion rather than mechanical effects become dominant.

Jan 1, 2005

By M. Brochu

In this paper, we present a computer-vision approach developed for wall-thickness measurements of corroded pipes inspected by double-wall radiography. The main objective of the work is to optimize data collection and film interpretation using computerized image analysis. To date, the system is able to identify the inner and outer contours of a pipe and perform wall thickness measurements at each pixel of a radiograph. This will be presented by analysing pipes having different dimensions. Another important feature of the system concerns the algorithms' adaptability to pipe wall texture. In other words, image analysis is automatically refined around rough or corroded areas. This allows more precise thickness measurements and shape identification in critical sections as will be demonstrated with examples. Finally a brief overview of results exploitation will be given and compared with human interpretation. It will show the reliability of automated image analysis and the many possibilities offered by complete output analysis.

Jan 1, 2005

By R. Druffel, P. Wittke-Gattermann, M. Wittke

"The two tubes of tunnel Hirschhagen along the highway A44 in Germany, underpass the federal road B7, a railway line and the valley of the river Losse close to the city of Hessisch Lichtenau. The ground in the area consists of Triassic sand- and siltstones (""Buntsandstein"") as well as tertiary clays. Prior to tunneling, the groundwater in the area is planned to be lowered by means of a gallery of deep wells. As a basis for the design of this dewatering gallery, two large pumping tests have been carried out. The results of these tests have been evaluated by means of 3D-Finite Element analyses. By means of the large-scale model, the influence of the anisotropy resulting from jointing and bedding and the influence of fault zones in the area have been taken into account, which lead to a thorough basis for the design of the dewatering gallery.INTRODUCTIONThe 4.2 km long Tunnel Hirschhagen of the highway A 44 crosses below the federal road B7, a railway line and the river Losse close to the city of Hessisch-Lichtenau in central Germany. Both tunnel tubes are located in a subrosion depression in which Triassic sandstone and tertiary clay prevail. It is planned to lower the groundwater table in the area of the meadow of the Losse prior to tunnel heading [1]. Groundwater lowering is planned to be achieved by means of a series of large pumping wells. The bottom of the river Losse will be sealed in order to avoid direct inflow of water from the river into the ground (Fig. 1 and 2)."

Jan 1, 2015

By R. Thierbach, W. Kahnt, Oberthür. T., D. Eisenburger, V. Gundelach

ABSTRACT: The ground penetrating radar (GPR) method was used in a platinum mine in Zimbabwe by members of the Federal Institute for Geosciences and Mineral Resources (BGR). The measurements were carried out in boreholes and drifts. Electromagnetic re?ections from a fault that consistently trends parallel to the mineralization zone permitted the mapping of the economically minable parts of the deposit. An introduction is given to the geology of the studied area and the application of the GPR method. The electrical parametres of the rocks are measured in situ, the GPR measurements are displayed with radargrams, and the visible structures are explained in illustrations.

Jan 1, 2010

By L. M. Guayacán-Carrillo, G. Armand, A. Noiret, D. Seyedi, S. Ghabezloo, J. Sulem

"The main purpose of this paper is to analyze the convergence measurements in a drift excavated in the Callovo-Oxfordian claystone. The drift axis is in the direction of the major principal horizontal stress whereas the stress state is quasi-isotropic in the drift’s section. The initial geometry of the drift being circular, the anisotropic character of the deformation is taken into account by assuming that the drift shape evolves in an elliptical shape. The convergence measurement data on six different points around the drift are analyzed to identify the main axes of the deformation ellipse, following the methodology proposed by Vu et al. (2013, Rock Mech Rock Eng, 46, 231-246). Then, using the semi-empirical law proposed by Sulem et al. (1987, Int J Rock Mech Min Sci, 24, 145–154), the convergence evolution is fitted independently for each axis of the ellipse. This method permits to distinguish two effects: the face advance effect and the time-dependent behavior of the ground. The results for the two directions of the ellipse axes show very close values for the parameters describing the time-dependent properties of the ground, the distance of influence of the face, and the extension of the decompressed zone around the gallery. Such model can provide valuable insights for predictions of the convergence evolution in the long-term. INTRODUCTIONDeep disposal of radioactive waste has been studied in France for more than two decades. The French National Radioactive Waste Management Agency (Andra) began in 2000 the construction of an Underground Research Laboratory (URL) with the main goal of demonstrating the feasibility of a geological repository in Callovo-Oxfordian claystone. Several research programs have taken place to improve the knowledge of the rock properties and its response to the excavation progress. The optimization of supports design for long-term behavior is an important point to develop. A network of experimental drifts has been constructed with variations on: excavation method, structure geometry, supports system and orientations with respect to in-situ principal stresses’ directions. In each drift different sections have been instrumented to monitor the convergence evolution and the rock deformation. Continuous monitoring of the excavated zone around the drifts revealed the development of a fractured zone (extensional and shear fractures) induced by the excavation. The extent of this fractured zone depends on both the drift orientation and the in-situ stress field (Armand et al., 2014). Indeed, the fractures distribution has an important influence on the convergence of the drifts."

Jan 1, 2015

By C. J. Hall

This paper presents a basic motive column analysis of natural ventilation and shaft resistance, using the density depth diagram. The method makes use of tables showing the state of the air as determined by thermodynamic analysis. Several theoretical examples are given.

Jan 1, 1968

By C. D. M. Chisholm

Introduction The Sullivan orebody is a sulphide replacement deposit in beds of argillaceous quartzites. The general strike of the vein is north and south, with rather an abrupt change to northwest in the north limits, and a pronounced steepening of the dip in the same area. An east-west section across the orebody in the vicinity where the change in strike occurs will show the dip-to the east-to be about 10° to 20° above the 4500 level, 20° to 30° between the 4500 and 3900 levels, and 35° to 45° between the 3900 and 3500 levels. It is this last section, averaging 75 feet in thickness, that is being mined by the blast hole method discussed in this paper. Typically, the mineralization throughout this section follows the same general pattern between footwall and hanging-wall, there being solid sulphides for a width of 30 to 50 feet, above which lie quartzite beds of varying widths separated by ore bands which also vary in width and in grade. This banded part of the vein usually extends for 30 to 40 feet above the solid sulphides, with commercial ore terminating on reaching a siltstone bed. Development is generally carried to the highest ore band which, when averaged with the underlying quartzite band, will assay about the marginal limit in lead and zinc. When wide stopes are opened, sloughing to the siltstone usually occurs and, although the values are too low to carry the cost of developing and mining, the caved muck can be handled profitably with only haulage and treatment to be considered.

Jan 1, 1946

By O E. Weightman

This paper describes the methods used for the ventilation of raises, sublevels and drawholes at Cominco's Sullivan mine. The problems involved in ventilation during blasting, drilling and scraping operations are first re-viewed, and then the air mover, a piece of equipment developed at the Sullivan mine, is described. The design of this device is discussed, along with the operating procedures used. Some figures are given to show the effectiveness of the method. THE Sullivan mine, located at Kimberley in the southeast corner of British Columbia, is owned and operated by The Consolidated Mining and Smelting Company of Canada Limited. Current daily production is approximately 10,000 tons. The mine is developed by sixteen levels over a vertical range of 2,000 feet. The total ventilation requirements, which amount to approximately 1,000,000 cubic feet per minute, are handled through a network of fresh air intake and foul air exhaust circuits. In addition to the many development and production headings, there are three crushing chambers and an extensive conveyor system which must be ventilated.

Jan 1, 1965

By S McQuitty

The metallurgical treatment of Falconbridge ore re-quires an extremely fine grind of the pyrrhotite portion ? for maximum liberation and recovery of nickel. This paper describes the operation of a grate discharge pebble mill in closed circuit with cyclones regrinding 25 to 30 tons per hour of sulphides to approximately 90 per cent minus 325 mesh. The consumption of the screened ore grinding medium is of the order of 2.5 pounds per kw.-hour, or less than 1 per cent of the tonnage of re-ground sulphides. IN RECENT years, there has been a considerable interest in pebble grinding in the uranium industry, and a number of installations have appeared. However, the use of sulphide ore pebbles as a grinding medium has so far been relatively limited. There has also been some question as to their suitability for the very fine grinding of sulphide concentrates. This paper describes the preliminary results of a commercial operation involving the

Jan 1, 1964

By Y. Obara, A. Sato

"Limestone is one of the most important mineral resources, and in Japan it is only one mineral which can be fully supplied by the domestic product. Generally limestone mines in Japan located at mountainous regions, and the combination between bench-cut method and the carry-out system using vertical shaft is widely used in the domestic mines. During mining operations, the occurrence of the blockage in the vertical shafts is very serious problem. Once the blockage in the shafts is occurred, a lot of works and dangerous procedures are necessary to solve the problems. It is thought that blockage is influenced by the cohesion and friction coefficient due to clay minerals thrown into the vertical shafts, however, the quantitative and precise reason is not revealed yet.In this study, the process of blockage occurrence was simulated by 2-Dimensional Discrete Element Method (DEM). In the 2D-DEM analysis, discontinuous circular particles are generated, and the individual movement of each particle is calculated by forward difference method. In the analysis, several typical ore distributions are applied, and the DEM analysis was conducted under the various combinations of cohesion and friction coefficient. From analytical results, it was found that the friction coefficient strongly influences to the occurrence of blockage and there were a threshold values which blockage does not occur. Several kinds of shaft shape were also simulated towards different ore size distributions, and those influences to the blockage occurrence were also discussed."

Jan 1, 2015

By J. R. Johanson, A. W. Jenike

"A solid flows out of a bin provided that the outlet is sufficiently large so that stable obstructions to flow do not develop. The geometry and surface finish of a bin and the construction of the feeder determine the type of flow pattern which then develops within the bin. The pattern, in turn, affects the uniformity and consistency of the stream, segregation, caking, degradation, live capacity and the action of level measuring devices.In most bins now in operation, material flows toward the feeder through a channel which forms within the stationary solid. This is referred to as funnel flow. If the hopper of the bin is sufficiently steep and smooth and the feeder capable of drawing material across the whole area of the outlet, all the solid flows whenever the feeder is in operation; this is referred to as mass flow. Mass-flow bins are usually far superior to funnel-flow bins; their initial cost is also usually higher.The paper describes the design criteria used in deter-mining the minimum bin outlet needed for flow and the bin geometry needed for mass flow."

Jan 1, 1970

By Bradford P. Simser

The theoretical capacity of various ground support components can be misleading, especially in bursting ground where the failure mode is often in the retainment system. Wire mesh screen seams often peel open rather than breaking the wire strands, fractured rock often un-ravels around the bolts rather than breaking the bars. If a weak link(s) in the system fails prematurely, then the potential capacity of the system may never be fully realized. Underground observations are used to show how some support systems behave in the field. Various combinations of wire mesh screen with friction bolts, rebar, modified conebolts, cablebolts, shotcrete and mechanical rockbolts are considered. A short case history is used to contrast the performance of ?just-intime? development in a high stress faulted area versus a tunnel subjected to multiple stress changes in a similar environment. The latter proved to be a serious ground support problem when the well developed fracture zone around the opening was subjected to dynamic loading from a large seismic event causing a severe rockburst. In such cases an improved mining strategy may be more relevant than higher capacity support systems.

Feb 1, 2008

By P. E. Cavanagh

Abstract Many investigators have been interested in developing some non-destructive method for detecting or determining the changes in physical properties in steel occurring during endurance tests or normal service life of a part which fails in fatigue. This paper presents a broad discussion of some of this work and the possibilities of developing useful test procedures based on some of the information obtained in the past. Changes in magnetic properties, electrical resistance, damping capacity, X-ray diffraction patterns, and remaining fatigue life at load different from service load have all been investigated as possible means for following the sequence of events during fatigue failure. In some special instances, tests such as these may be used to predict fatigue failure. As an in stance of practical application of the continuous determination of changes in magnetic properties during fatigue, a brief account is given of work done in non-destructive inspection of mine hoist-rope. As a result of extensive experiments and field crisis, it has been found possible to detect the beginnings of failure in a wire rope in service. The test method used will detect plastic deformation in a wire rope, no matter what its cause. There is no possibility of determining the remaining useful life of a rope by calibrating changes in magnetic properties in terms of remaining fatigue life. A change in magnetic properties at a point in a rope may indicate a decrease or increase in fatigue life, depending on the overload history of the rope. A continuing change in magnetic properties ac a point, however, does reliably indicate a developing weak point which will eventually lead to failure. The important point about any change in magnetic properties is not the magnitude of the change, but whether or not it continues.

Jan 1, 1947

By J. G. Speight

Laboratory studies indicate that autogenous heating of low-rank coal can be prevented by a prior treatment which involves immersing the coal for short (5-15 min.) periods in an inert liquid at temperatures between ~ 350° and 400°C. Such "carbonization" effectively reduces the accessible pore volume of the coal to levels at which heat generation through subsequent sorption of moisture and oxygen is too slow to cause significant temperature rises in a stockpile. In addition, this treatment also irreversibly removes most of the moisture held in the raw coal and raises its calorific value by as much as 10-12%.

Jan 1, 1973