Search Documents

By Jochen Franke, Derek D. Lichti

"This paper gives a brief introduction and presents recent enhancements in the MillMapper technology developed for thickness gauging and condition monitoring of liners in grinding mills used for mineral comminution. It also introduces the recent expansion of MillMapper functionality aimed at mill operational optimization. MillMapper uses calibrated laser scanner data captured inside a mill to determine thickness at several million points on all liner surfaces at feed, shell, and discharge ends with millimeter accuracy. Data capture takes nominally 5 minutes, hence interruption to mill operation is negligible.The paper is structured as follows. First, a review of the technology and discussion of recentlyimplemented innovations such as liner change out forecasting, automatic ball charge volume and weight measurement, and automatic mill liner volume/weight measurement for mill operational control or load cell calibration are presented. Combined weight information provides control over load related issues such as load fill levels for relining, or start-up load after reline. Feature descriptions are followed by a listing of the numerous advantages over existing techniques and the benefits to operations. Results from the application of MillMapper are presented throughout.INTRODUCTIONThe need for thickness gauging of liners of grinding mills used for mineral comminution is well known but the task is rarely completed to a satisfactory standard. Liner failure resulting from excessive wear can have expensive consequences. Furthermore, mill performance as well as liner wear are known to be correlated to lifter bar geometry (Napier-Munn et al., 1999; Rajamanni et al., 2005). At present, the following techniques are routinely used to gauge the thickness of mill liners:1. Visual inspection;2. Ultrasonic thickness gauging (for steel liners); and3. Physical inspection (e.g. nail inserted in rubber liners)"

Jan 1, 2008

By David Rahal, Des Erasmus, Ken Major

"Over the past twenty years there has been an increased emphasis on fine grinding in the minerals industry. This spurred the development of a range of new fine grinding equipment in the 1990s. At that time, the Knelson-Deswik mill was developed in South Africa for the pigments industry.Knelson Milling Solutions currently offers a wide range of laboratory, pilot and production scale mills. These mills bridge the gap between traditional low speed vertical mills and the high speed horizontal mills (tip speed < 3 and > 15 m/s respectively). They are designed to run at tip speeds between 10 and 12 m/s and are capable of operating with very dense grinding media. The result is a power intensity that is higher than the low speed mills and overlaps that of the high speed mills. This allows the mill to be customized for a wide range of grinding applications.A case study at Aquarius Platinum’s Kroondal Mine shows that the Knelson-Deswik technology can produce a consistent product size despite feed variations. It also shows that the throughput was proportional to the slurry density at Kroondal. The case study identified increasing the slurry density as a process change that can increase throughput and reduce the specific energy consumption.INTRODUCTIONThe increasing complexity and finer grain sizes of modern ore bodies have increased the importance of effective mineral liberation in obtaining acceptable grades and recoveries (Jankovic, Valery and La Rosa, 2003; Lichter and Davey, 2006; Napier-Munn, Morell, Morrison and Kojovic, 1996). This trend has increased the significance of fine grinding technology because the input energy increases exponentially as the required product size decreases from 100 to 10 microns (Gao and Weller, 1993a).The US Department of Energy recently provided the context for the potential energy savings in the US Mining Industry (BCS, 2007). They reported that grinding consumes approximately 494 TBtu/year. This was over double the consumption of the second highest equipment category, diesel materials handling systems (211 TBtu/yr). The proportion of grinding energy allocated to fine grinding can only be expected to increase as finer ore deposits are mined. It is therefore critical that fine grinding efficiency continue to improve through the selection of appropriate equipment and the development of best practices for existing applications."

Jan 1, 2011

By Tony Moore, Peter Riccio

"MMG (Minerals and Metals Group) operates the LXML Sepon’s mineral processing facility located 40 kilometers north of the town of Sepon, in the Savannakhet Province, Lao PDR. The Sepon copper plant produces 70,000 tons/year of LME grade A copper cathode using leachautoclave- SX/EW-flotation technology (Baxter et al., 2003). Pyrite recovery in the flotation circuit is critical to the operation, as it is used to generate acid and soluble ferric ion for the leach circuit. Low pyrite recovery has been an on-going challenge in the flotation circuit. Final tailings characterization work done by Ian Wark Research Institute (Bassell et al., 2006) showed that the pyrite losses to the tailings are made up of a combination of coarse liberated particles and finer particles that have been coated by clay fines.In December of 2005, a joint Cytec-MMG technical program was initiated to address the pyrite recovery issue. A series of diagnostic tests were performed in the Cytec Stamford Research Facility using synthetic plant water showing that the collector was precipitating as a metal salt and was unavailable for mineral attachment. The tests also identified several collector chemistries that would likely be robust in the low pH (< 1), high dissolved metal ion environment and will not complex with metal ions in solution. With the support of the Sepon on-site engineers, an extensive, successful laboratory program was completed, which was subsequently followed by on-plant testing that showed a step wise improvement in pyrite recovery.INTRODUCTIONLow pyrite recovery has been an ongoing problem in the flotation circuit at Sepon. Sulfur recovery (indirect measure of pyrite) was improved from 40% to 65%-75% in mid-2005 when on site laboratory work confirmed that AERO® 8045 Promoter was a more effective collector then AERO® 407 Promoter. However, sulfur recoveries above 65% could never be achieved. Sepon requested the Ian Wark Research Institute to complete a surface analysis study using Scanning Electron Microscopy, X-ray Photoelectron Spectroscopy, and Time-of-Flight Secondary Ion Mass Spectroscopy to determine if clay coated pyrite played a role. It was concluded that the pyrite losses to the tailings are made up of a combination of coarse (+ 100µm) liberated particles and finer (-74µm) particles that have been coated by clay fines. The majority of the losses appear to be due to the former. In December of 2005, a series of diagnostic tests were performed in Stamford using synthetic plant water in order to identify what chemistries would likely be robust in the slimy low pH and high dissolved metal ion solution environment. Results showed that several chemistries would not complex with ferric, ferrous or copper in solution and therefore should perform well in the Sepon flotation. The incumbent collector, AERO® 8045 Promoter was complexing with metal ions in solution. This resulted in the collector not being available for adsorption onto pyrite."

Jan 1, 2011

By Adil Aledresse, Louis Mercier, Laxman Amaratunga

"The development of high capacity adsorbents with uniform porosity denoted, MP-HMS (Mercaptopropyl – Hexagonal Mesoporous Structure) using nanotechnology, and their ability to extract gold from solution, is presented. The preparation of highly effective heavy metal ion adsorbents by the incorporation of thiol moieties into the pore channels of mesoporous silica molecular sieves has been the subject of many nanotechnology research investigations. The unique feature of these nanoporous adsorbents is their ability to adsorb gold ions from ultra-low concentration solutions like mine effluent as well as from leached solutions in gold mills. The preliminary studies from laboratory simulated gold solutions show that the adsorption capacities of these materials are also among the highest reported. MP-HMS has shown the capability to adsorb 370 mg gold per one gram of the nanomaterials from Tetrachloroaurate solution (up to 37% of their weight). Experimental studies indicated that the maximum adsorption of gold (as high as 99.9% recovery). The current studies will be extended to investigate the interaction of ionic gold complexes with nanomaterials. Future development of this work may lead to either to replace the conventional CIP/CIL processes or use nanomaterials in tandem with the former, suggesting plausible use of mesoporous material in pulp, MIP or in leach, MIL, as a novel gold extraction process.INTRODUCTIONGold typically occurs at very low concentrations in ores less than 10 g/t or 0.001% (mass basis). At these concentrations the use of aqueous chemical (hydrometallurgical) extraction processes is the only economically viable method of extracting the gold from the ore. Typical hydrometallurgical gold recovery involves a leaching step followed by the separation of the gold bearing solution from the residues, or adsorption of the gold onto activated carbon adsorbent. After elution from the activated carbon the gold is further concentrated by precipitation or electrodeposition."

Jan 1, 2008

By S. Banisi, H. R. Iran-Manesh, M. R. Shayestefar, H. Shekarchyan

"Flotation circuit of the Sarcheshmeh copper mine processes 41,000 t/d of ore at 0.9% Cu. Chalcopyrite and chalcocite are the main copper bearing minerals which are concentrated in three stages of roughing, cleaning and recleaning. Due to major changes in the reagent addition regime, make-up balls combination, and throughput to the primary mills an increase of 2.6% (from 87.2% to 89.8%) in the sulfide copper recovery was obtained during a period of six years. In order to investigate a rather large variation of monthly recovery (i.e., from 89.0 to 91.2%) of the plant after implementation of the changes, a study was undertaken to trace mineralogically possible causes of such a behavior. During a five-month period, monthly composite samples of feed and tailings of the flotation circuit were taken. At the first stage, the polished sample preparation method and the mineral counting procedure were optimized through a detailed study. Liberation degrees and types of locking of valuable minerals in both streams were determined in three size intervals of +75, +38 and –38 microns. It was found that for both recovery levels (i.e., 89% and 91.2%), there was no significant difference in the liberation degrees of valuable minerals in the flotation feed; the average liberation degree was 57.1% with a standard deviation of 3.1%. On the other hand, in the case of high recovery level (i.e., 91.2%) there was a reduction of 15% in the amount of free valuable minerals in the tailings stream. The highest reduction was found for the -38 micron size range in particular for chalcocite. It was concluded that compared to the grinding circuit the change in the flotation circuit had the significant effect on the plant recovery increase.INTRODUCTIONThe Sarcheshmeh copper ore body contains 1 billion tonnes averaging 0.90 % copper and 0.03 % molybdenum. It is located southeast of Iran and currently processes 41,000 t/d of ore. The concentrator has been in operation since 1982. Last year, the concentrator produced 130,000 tonnes of copper and 4,000 tonnes of molybednite concentrate. An expansion to the plant which will increase the throughput by 50% is under construction and will be effective in 2003.After three stages of crushing, the ore with a F80 of 12.7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of the first stage of flotation is reground and the tailings constitute the main component of the plant final tailings. A concentrate with an average grade of 30.5% Cu is obtained after cleaning and re-cleaning stages. At the present time, the average sulfide copper recovery of the plant is 89.8% which varies depending on the operating conditions and ore type."

Jan 1, 2003

By Claude MacDonald, John H. Ashburn

"IntroductionIndustrial growth and technological change over recent years had been accompanied by two major sources of concern to management and employees: (a) increase in occupational injury and illness and the resultant costs involved; and (b) equipment damage and breakdowns in concentrated production lines causing more extensive loss potential.Due to economic factors, management attention has focussed more on production and quality than on safety, health and related loss potential sources. As a result , occupational safety and health activism has grown, government legislation of compensation and occupational safety and health standards have progressively developed and stronger liability attitudes have been taken by courts of law.To improve efficiency and allow development in more competitive markets, rising labour costs, equipment costs and safety related financial losses have dictated that attention be given to conservation of all resources. Conservation of resources, people, equipment, material and environment, can no longer be addressed in isolation but must be managed integrally with production and quality. To this end, systems have developed utilizing sound management principles applied with equal intensity to production, quality and loss potential"

Jan 1, 1987

By J. K. Afidenyo, J. Osei-Owusu

"The Obuasi Mine of AngloGold Ashanti Limited has been operating the world’s largest Biooxidation Plant at its Sulfide Treatment Plant (STP) in Ghana, using the Gencor Biox® technology since February 1994. The Biox® technology was preferred to other alternative methods of treating refractory sulfide ores such as roasting, pressure oxidation and nitric acid leaching due to among other reasons, its lower capital and operating costs, reduced technical risk, relatively benign environmental impact and its ease of operation and maintenance in a remote location.STP has since commissioning succeeded in operating this technology successfully but not without some operational problems. The Plant has seen a number of upgrades and modifications in its circuits which were motivated by cost, operational and throughput constraints.The objective of this paper is therefore to highlight the mine’s experience in the treatment of its complex carbonaceous refractory sulfide gold ores with emphasis on plant operations and improvements such as the Biox® reactors expansion, flotation concentrate upgrade project and neutralization circuit modifications. The Biox® Plant operating cost is also discussed.INTRODUCTIONThe Obuasi mine forms part of the AngloGold Ashanti Group of Gold Mines. It is located in the Adansi West District of the Republic of Ghana. The mine is primarily an underground operation, although some surface mining still takes place. Ore is processed by two main treatment plants: the Sulfide Treatment Plant (for underground ore) and the Tailings plant (for tailings reclamation operations). A third plant, the Oxide Plant, is used to batch-treat remnant opencast ore and stockpiles, of which there are adequate tonnages to keep the plant operational until 2008.Though reference is made in this paper to the Tailings and Oxide Treatment Plants, the main focus will be on the Sulfide Treatment Plant."

Jan 1, 2008

By R. V. Ramani

"A computer simulation model of a dragline has beer developed for the study of alternative dragline deployment schemes for varying geological and mining conditions. In this paper, the mathematical aspects of the model, the input data and output results are discussed. An application of the model to a coal mine in eastern Kentucky is presented.IntroductionDraglines are very productive machines. To extend their operating ranges, they are operated in several modes such as advance benching, key cut, extended benching and pullback. Unfortunately, these variations result in low machine productivities. Appropriate methods to operate these machines must be developed on the basis of detailed analyses of dragline performance under varying geological and mining conditions. There are several standard engineering procedures for the selection of dragline, and design of a dragline pit (Ramani, Iroegbu and Manula, 1976). However, the complex interrelationship which exists among equipment, methods and natural conditions can be quantified only through orderly and systematic experiments.Computer simulation is well suited to studying these types of equipment selection and method layout problems. Several alternatives can be analyzed in a relatively short time by the modification of input variables. Also, the application of computer simulation models can significantly reduce the manpower and cost required for such analysis."

Jan 1, 1985

"The outlook for Eastern Canada is decreasing coal production over the next few years; however, a reappraisal of the long-term requirements and increased prices of coal could lead to a revitalizing of the industry. The market for Western coal is expanding and is expected to exceed 50 million tons per year in the metallurgical and thermal power fields. Western coal reserves are currently estimated at 119 billion tons. Technical developments in Eastern Canada include a shearer and gate-end support system to mechanically cut the stall and brushing at the tail-end of a longwall. In Western Canada, the most modern equipment is used in mining, beneficiating and shipping coal. Results to date on the underground hydraulic experiments exceed expectations. The importance of reclamation is recognized and plans have been made to restore and re-vegetate disturbed areas and mine dumps. In Eastern Canada, experiments were started to determine the feasibility of coal reclamation from mine dumps, including one dump that is on fire. The Mining Research Centre, Mines Branch, continued to conduct research work oriented toward solving Canadian mining problems The Western office of the Centre, opened in 1970, was set up primarily to study problems associated with a resurgent coal industry."

Jan 1, 1971

By Robert J. Maron, Mark Fernald, Alex Van der Spek, O’Keefe. Christian, Tim Bailey

"Sonar array-based non-invasive flow measurement technology is becoming an accepted and many times a preferred method of measuring challenging single and multi-phase flows in the mineral processing industry. This fundamental sensor and measurement technology has been extended to two developments that provide new measurement capabilities useful for monitoring and managing slurry flows and pipes.The first development is the non-invasive measurement of real-time velocity profile of slurry flow in horizontal pipes. Multiple non-invasive passive sensors measure localized velocities and are combined to provide a velocity profile measurement. This information can be used to determine the approach and onset of solid deposition on the bottom of the pipe. Having this information in real time can enable operation at lower velocities and/or higher solids concentration while avoiding solids deposition or plugging and its associated operational costs.The second development is the non-invasive measurement of pipe wear on slurry lines. Presently, such measurements are made by hand-held portable ultrasonic thickness gages. The numerous shortfalls associated with the manual method are overcome with a set of permanently or semi-permanently installed transducers clamped onto the outside of the pipe. This ring of sensors contains a series of conformable ultrasonic transducers spaced around the circumference, which are used to measure the thickness of the pipe under their respective locations. Compared to manual methods, this system and approach results in better repeatability and accuracy. It also decreases inspection labor costs and pipe access requirements. The minimal accuracy variations in the presence of varying environmental temperatures will be shown. Trending of pipe wall thicknesses in high wear pipelines will be illustrated. The benefits of significantly improved pipe wear monitoring in hydrotransport lines with abrasive solids, and associated improvement in the ability to insure safe operation and avoidance of costly environmental damage due to leaks caused by pipe wear will be discussed."

Jan 1, 2009

By O. A. Bascur, J. Patrick. Kennedy

"The lack of integration of mining and metallurgical information at sufficient detail to act is a problem. Without such data, mine cut-off grade can not be optimized on a per grade basis. It is difficult to determine economics without integration of mine transactions, stockpile inventories, process flows and assays. Actions also require real time information from manufacturing assets, but corrected for gross errors from trucks, shovels, conveyors, faulty sensors, bad instrument calibration. Validation methods must include process models to identify corrupt actionable information. This paper presents new tools that use the model the process to sift through available data, identify and eliminate gross errors, and use statistical data reconciliation to create material balanced, internally consistent values. Uses of models allow data to be unified for useby both monitoring and decision making processes.A Real Time Performance Management (RtPM) uses unifying analysis methods to empower everyone in the organization with unparallel real-time intelligence, enabling them to continuously improve performance.BACKGROUNDExtraction of metals has become a global business; new economic and environmental forcing factors are present today which were unheard a couple of years ago that are causing companies to focus on plant operations. High ROI actions can be achieved internally which will increase mining and metallurgical processing unit efficiency and reducing operating costs if the proper information is provided those in the complex that can act. Large changes are possible with many of these small steps if the barriers for action are removed. The chief impediments are lack of infrastructure including the data, computing tools and essential data and bad information.Increased demands will be placed on the types, quantity and priority of information. Metallurgical complexes are attempting to become better neighbors, increase productivity, improve customer service, and satisfy the regulators and compliance groups -- all with fewer people and less costs."

Jan 1, 2004

By Gilles Landry, Mohamed Ourriban, Pierre Pelletier, Ahmed Bouajila, Claude Gagnon

"This paper summarizes the work carried out to develop and implement the gold cyanidation by size class (CSC) process, a novel concept aiming to reduce cyanide consumption.First, the authors will present the methodology and results of laboratory tests conducted to evaluate the response and the expected gains for the selected ore when submitted to the CSC processing. In the second part, focus will be on the methodology behind the CSC scheme development prior to its implementation at Sleeping Giant Mine concentrator. Finally, the evaluation of the modified circuit performance (operating since July 2007) will be addressed as a reduction of cyanide consumption by more than 30% and of free NaCN in the tailings by more than 50% is confirmed.INTRODUCTIONCyanidation is the most widely used technique to extract gold from hard rock ore. Its use of oxygen as an oxidant still makes it the cheapest process available after more than a hundred years. Unfortunately, gold cyanidation is known to be a slow process that requires high consumption of cyanide. In fact, cyanidation plants are designed with very long residence times (Habashi, F., 1967). Drawbacks of long cyanidation times are, among others, loss of gold in tailings, high reagent consumption and high capital investment and maintenance costs.Responding to their members expectations for the improvement of cyanidation process, COREM undertook a challenging R&D program covering the development of alternative concepts (processes) and the understanding and solving of mass transfer, gold passivation and process water chemistry problems. One of the interesting findings of the R&D program is a patent pending process technology based on the cyanidation by size class (CSC) concept (Côté and Ourriban, 2004; Gagnon and Ourriban, 2007; Gagnon and Ourriban, 2004).The new technology was tested at the Sleeping Giant concentrator, a plant member of COREM. The existing flowsheet was modified in order to implement the CSC process in the full-scale plant. The plant has been operated using the modified CSC based process since August 2007. Laboratory testwork was conducted prior to the industrial application in order to properly design the new process scheme. The modifications included:1) Reclassification of the grinding circuit product through an hydrocyclone2) Leaching of the coarse size fraction3) Addition of the fine fraction to the coarse leaching circuit tails."

Jan 1, 2009

By H. O. Ghaffari

A complex network approach on a rough fracture is developed. In this manner, some hidden metric spaces (similarity measurements) between apertures profiles are set up and a general evolutionary network in two directions (in parallel and perpendicular to the shear direction) is constructed. Also, an algorithm (COmplex Networks on Apertures: CONA) is proposed in which evolving of a network is accomplished using preferential detachments and attachments of edges (based on a competition and game manner) while the number of nodes is fixed. Also, evolving of clustering coefficients and number of edges display similar patterns as well as are appeared in shear stress, hydraulic conductivity and dilation changes, which can be engaged to estimate shear strength distribution of asperities.

May 1, 2009

By A. R. Miller, G. Desrivières, T. MacKinnon, H. Bursey, M. C. Bétournay, B. Replogle, D. L. Barnes, P. Laliberté

"A mine production locomotive, the world’s first applied industrial fuel cell vehicle, has been designed and tested in the context of a number of proof-of-concept projects supported by the Fuelcell Propulsion Institute, an international consortium of stakeholders dedicated to facilitate the commercialization of fuel cell vehicles.The locomotive’s simple electric-powered motor and controller system was ideal to study a number of requirements related to fuel cell power application: hydrogen power plant operation, underground hydrogen use, risk and regulatory requirements, production performance versus the conventional battery- powered locomotive version under measured duty cycles and production requirements, power plant design improvements for other fuel cell vehicles, and cost benefit aspects.This article will focus on the design and testing aspects of this project which has led to successful performance demonstrations of the vehicle under surface and underground conditions at two mines. It will also present information on the creation of a safe, reliable, and efficient power plant that fulfilled its design objectives, including longer productivity time for a given vehicle fill-up."

Jan 1, 2004

By Willemijn Husslage

Tata Steel Group At a glance ? Part of the Tata Group ?Tata Steel Group: ?Fortune 500 company ?Top 10 global steel producer ?Annual crude steel capacity of 28 million tonnes ?More than 80,000 employees ?Manufacturing operations in 26 countries across 5 continents ?Serving customers all across the globe ?Turnover 2009-10: $22.8 billion

May 1, 2011

By Jean M. Richardson, Steven R. Williams

"Geometallurgical mapping is a new team-based approach that documents variability within an orebody and quantifies the impact of geology (host rocks, alteration and structure) and mineralogy on grinding, metallurgical response and metal recovery processes. The quantitative, spatially constrained database that results can be readily integrated into 3-D block models and mine planning activities. Thus it is an important tool to reduce the technical risk associated with new mine developments or expansions.Normally undertaken during pre-feasibility or feasibility planning stages, the first step of geometallurgical mapping is to review the geology, mineralogy and other critical parameters and construct a geometallurgical matrix. This matrix provides an objective base to then guide sampling and/or compositing activity for physical property and metallurgical testing. Depending on the project, an array of testing techniques can be used to characterize the ore and feed data into the geometallurgical model.While the range and number of tests needed is project-dependant, the geometallurgical mapping approach allows the development of empirical models or interdependent relationships, grounded by spatially-constrained real data. Extensive data sets collected using less expensive testing methods can be meaningfully correlated with results from complex specialty tests to yield realistic metallurgical recovery data.With geometallurgical mapping completed, the resulting database can be integrated into an overall 3-D block mine model. This means that metallurgical response can be used to realistically forecast the recoveries of specific blocks, perhaps sampled only by drilling. Mine planning can then incorporate the forecasted metallurgical response and generate future project cash-flows; opening the door to economic optimization of the mine exploitation."

Jan 1, 2004

By P. Tittes, M. Deal, M. Spicher, S. McDaniel, J. Wickens

"Haile Gold Mine is located near Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The relatively low grade and refractory nature of the deposit has been a challenge for efficient processing since the start of mining on the property. Early processing techniques included gravity separation and barrel chlorination. The last operation employed heap leaching in 1985 through 1992. After being closed and reclaimed for over 20 years, the property is poised to re-open and produce once again. In this chapter of the Mine’s legacy, flotation and ultra-fine grinding will be employed to achieve economic extraction of gold and silver from the pyrite. This paper briefly reviews some of the mine’s history, the metallurgical testing, the flowsheet and discusses design considerations.INTRODUCTIONHaile Gold Mine is located near Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The last operation employed heap leaching in 1985 through 1992. Since then, the property has been closed and fully reclaimed. Romarco Minerals acquired the property in 2007, and began an exploration program that has delineated over 62 tonnes (+2M ozs.) of gold in reserve at an overall grade of 2 ppm (0.06 opt). This paper provides a brief history of the property, a summary of metallurgical testing, description of the process flowsheet and discusses design considerations.HISTORY1827 – 1837Gold was discovered in creek beds on the Haile property in 1827. The property was owned by Benjamin Haile, and the first few years of production came from placer mining. After gold was discovered in schist beds to the sides of the streams, Haile expanded the operation by leasing 18 meter-square (50 ft.) plots to local planters. These planters used slaves to work the small excavations in the agricultural offseason. The gold ore was taken to arrastras where the free gold was liberated and recovered. The excavations were above the water table, generally less than 18 meters (60 ft.) down, and it was noted then that gold could be found embedded in sulfides and difficult to extract."

Jan 1, 2013

By Janis A. Shandro

The mining sector is a major economic driver for Canadian, and British Columbian communities. In parallel strong commitments have been made by industry to the well-being and sustainability of associated communities. However, these dimensions are the least understood. Especially lacking are focused regional investigations that compare the well-being and sustainability of communities dependent on different resources sectors. It is hypothesized that this type of comparative analysis will help to foster a greater understanding of what makes a resource or mining community healthy and sustainable. This paper describes research that examined community-level indicators associated with well-being (e.g. education, income and employment) and sustainability (e.g. economic diversity). The indicators were derived from Canadian Census data for 31 British Columbia resource-based communities (with a focus on mining) during a period of time (1991 to 2001) when resource sectors experienced an economic downturn. Our findings identify that during this decade, mining communities differed significantly from other resource-based communities, and comparative analysis of census derived indictors illuminate challenges that mining communities in British Columbia face with respect to wellbeing and sustainability (such as economic diversity, unemployment, and population loss). To contribute to the mining sector?s efforts towards meeting their commitments to communities, this paper concludes by proposing strategic opportunities aimed at the enhancement of mining community sustainability for policy-makers, communities, and the mining industry to consider.

May 1, 2011

By R. Haecker, S. Bajic, R. Thorpe, A. Palko, M. Kalstrom

"Historically, mineral processors have used inferential data like plant instrumentation, assays, and grind sizes to monitor the performance of their plants. The ability to monitor the minerals themselves on a daily basis has eluded all but the very largest and richest of operations. The advent of a new generation of compact, robust, and user-friendly SEM-based automated mineralogy systems looks set to accomplish this, aiming to bring daily mineral monitoring of plant performance within the reach of all mills from mid-size upwards. This paper describes the use of this machine at Greens Creek Mine, a 2.5 ktpd Ag-Au-Pb-Zn operation with a complex flotation flowsheet. During the trial, the machine provided turnaround from sample collection to reporting averaging 24-36 h for key daily samples. All equipment was located within the compact mill, and proved highly reliable despite the challenging environment. Turnaround time was fast enough for metallurgists to understand, and, where possible, respond to ore and process changes while they were still happening. The plethora of data generated was filtered to a simple report whereby mill management could quickly absorb key daily mineral-based performance indicators. This paper will describe how the data was used to understand the key drivers behind metallurgical efficiency at Greens Creek, and how metallurgists began using the information to enhance daily mill performance."

Jan 1, 2014

By R. J. Balfour, T. L. Papucciyan

"INTRODUCTIONCapital Cost considerations are basic to feasibility in the achievement of success for Mineral Processing Projects as much as or more than in many other industries. Capital cost is an important factor ae it 1R the unit of measurement for process engineering economic decisions. As a result of ever increasing complexity, alternatives of process and remoteness of site, there is an ever increasing emphasis on accurate estimating and the attendant cost control systems in the international market of today for the Mineral Industry where initial plant costs are becoming a more important factor than operating costs. An undervaluation means trouble ahead. An over-cautious assessment may bring an unnecessary abandonment of a project. Consequently, the ultimate cost must be predicted early and accurately and must be controlled to this parameter during the design and construction phases. Cost Est!~ mating is one of a variety of project management tools used to assist in planning and achieving the optimum balance between Quality, Cost and Time, the eternal triangle of evaluation, namely obtaining a project of acceptable quality at minimum cost and on time. In order to attain these established objectives, proper planning, organizing, coordinating, monitoring, adjusting and controlling the design, procurement and construction elements of the project are essential.This project management approach based upon the principle of a Task Force under single management, comprising a complete service organization, requires a substantial number of qualified individuals specialized in their own field and capable of working together as a team to perform their various functions effectively. The Task Force is supported by their chiefs of discipline and performs in accordance with established procedures and standards under the leadership of a Project Manager.General Engineering Company Limited with the backing of the full resources of Surveyer, Nenniger & Chenevert and its total staff of approximately 1,0009 offers the complete project management service to the Mineral Processing Industry of North America and the rest of the world. As mine sites become more remote and difficult of access, the need for an experienced team of specialists who work under the Task Force principle, with well established standards and procedures becomes even more important. Our long history of successful pro1ecta in this field has been our training ground for the fulfillment of this need."

Jan 1, 1972