Search Documents

By So-Yeong Lee, Moosang Lee, Seung Hwan Ahn, Ho-Sang Sohn, Jongshin Chang

It is necessary to understand the characteristics, phase changes and chemical reactions of flue dusts introduced from a furnace to an off-gas line in order to achieve the stable operation and the improvement. This study is to develop the dust reaction model for chemical reactions of dusts in an uptake shaft of smelting furnace and a waste heat boiler. Phase equilibria and reaction paths in this system were determined by thermodynamic calculation with experimental and industrial data. The oxidation reaction rate of dusts was determined by the gas film mass transfer controlling. And the sulfation reaction rate was evaluated by the unreacted shrinking core model. Kinetic parameters were estimated by reference data including industrial ones. The present study with the developed model shows various effects of temperatures, dust particle sizes, and O2 gas partial pressures on dust reactions. INTRODUCTION The flue dusts from a copper smelting furnace move along a furnace off-gas stream into an uptake shaft and a waste heat boiler (WHB) and electrostatic precipitator(s). It is necessary to control the dust quality in order to stabilize the operation because the sticking behaviors differ depending on the phase of dusts. Phase changes of dusts are caused by chemical reactions at given conditions such as temperature and partial pressure of gases. Therefore, it is required to understand the phase changes and chemical reactions of dusts in order to perform the improvement and stable operation. The present study carried out the investigation to understand their fundamental knowledge. Especially, this study was focused on the kinetics of chemical reactions of flue dusts, developed the model. In particular, the scope of development and utilization of the model was defined as the uptake shaft of the Mitsubishi S furnace and the S-WHB radiation section in the Onsan smelter. Information needed for the modeling work referred to data from these processes.

Jan 1, 2019

By Yufeng Yao, Robert P. Lowell

Abstract - Conductive heat flow anomalies associated with hydrothermal sulfide mounds on the seafloor have been studied. Sulfide mounds tend to focus conductive heat flow because sulfide minerals have a greater thermal conductivity than country rock. The topography of the mound above the seafloor, however, leads to a reduction of heat flow, particularly near the center of the mound. Because the focusing effect is constant, whereas the topographic effect decreases with distance away from the center, the focusing effect dominates toward the edges of the mound. The magnitude of these effects depends upon the conductivity contrast and the height/radius aspect ratio of the mound. Conductive heat flow anomalies at sulfide mounds also result from fluid circulation within the edifice. For the active and relict mounds at the TAG hydrothermal field, which have an aspect ratio of approximately 0.3 and a conductivity contrast of 3, the heat flux through the center of the mound should be roughly 70% of the background heat flux. The maximum effect of heat flow focusing is to increase the heat flux by about 30% above background. By comparing these effects with conductive heat flow data at TAG, we find that advective processes dominate conductive heat flow at both the active and relict mounds. Advective circulation can also give rise to much larger lateral and vertical temperature gradients than would result from conduction alone.

Jan 1, 1999

By A. F. Banks

"IntroductionThe typical potash processing plant recovers and/ or upgrades from 10% to 20% of its production through the recrystallization process. The feed to the recrystallization section consists of preconcentrated slurries of fine crystal size that cannot be raised to the required product grade by flotation and fine dusts also of low grade and too fine for compaction feed. It produces high grade white potash crystals that can be marketed as a high grade product or blended into the flotation products to raise their grade. In this chapter, a typical leaching (dissolving) and recrystallization operation will be discussed.The crystallization process makes use of the three phase system chemistry of NaCl, KCl, and H,O. The normal potash process operates on a temperature range of 75°F to 95 °F. A three phase slurry feed to the dissolving circuits will be within that range. The potash (KCl) is dissolved by heating the slurry in the presence of sufficient brine to a temperature of 190°F to 200°F. As the slurry is heated, the potash (KCI) dissolves and the salt (NaCI) precipitates. The potash rich brine is then clarified and the salt and other undissolved solids removed by thickening. Clarified brine becomes the crystallizer feed.The hot brine is cooled in evaporative cooling crystallizers. In cooling, the potash precipitates as a high grade white crystal. Crystallization is done in multiple effects to permit energy recovery and control of the process. In a four effect crystallizer the cooling is done by recycling mother liquor counter currently through the first two effect condensors and using brine pond brine for the cooling of the last two.The crystallizer product is removed from the last effect as a slurry at normal process temperature and is fed either to its own centrifuging and drying circuit or blended with the flotation product for centrifuging and drying."

Jan 1, 1989

By Charles Graham

For hundreds of years the standard vertical mine shaft was rectangular shaped and timber lined. There are many advantages to rectangular shafts but as mines became deeper the circular shaft became more popular. The chief advantages of circular, concrete lined shafts are their ability to resist lateral pressure and they offer less resistance to ventilation air. A number of elliptical shafts have been sunk in an attempt to realize the advantages of both the rectangular and the circular shaft. A concrete lined elliptical shaft provides better space utilization than a circular shaft, would allow for shaft sinking with two double drum hoists, as well as concurrent level development. The design also makes one sided stations possible and provides for a simple headframe design.

Feb 1, 2008

By Kevin Azocar, Jim Hazzard

"Slope stability analysis is performed most commonly using limit equilibrium calculations or numerical models assuming a two-dimensional slice through an infinitely long slope surface. In areas such as open pit mining, where most slope surfaces are not planar, the importance of curvature becomes important due to the economic gains associated with creating a steeper slope. With advances in computing capabilities within the last decade, three-dimensional slope analysis can be performed within reasonable time frames. Some work has been done on the potential importance of curvature on slope stability, mainly assuming homogenous materials with a circular shear-failure mechanism. However, many open pit mines are excavated in jointed rock mass where a completely different set of failure mechanisms can be seen. Depending on the geometry and radius of the pit, the curved geometry may influence the factor of safety and failure behaviour compared to a two-dimensional slice.A series of numerical analyses were performed to investigate the effect of curvature on jointed rock slope stability compared to an equivalent two-dimensional slope analysis. By using discrete element method models, the influence of joint planes and interaction between distinct blocks can be seen. With a three-dimensional model, the effect of curvature can be combined with multiple joint sets at any orientation, which cannot be seen in a single slice. Numerous three-dimensional models are created, along with an equivalent unit-thick slice. The effect of curvature on a variety of different types of failure mechanisms is observed, and graphical relationships are created to quantify the difference between the three-dimensional factor of safety and the two-dimensional factor of safety based on the degree of curvature."

Jan 1, 2015

By E. A. Hart, J. E. Gill

"The property of Arntfield Mining Corporation, formerly Arntfield Gold Mines, Limited, covers an area of 2,110 acres and lies in Beauchastel township, western Quebec. The Francoeur mine lies to the west, and to the east are the West Wasa and Wasa Lake properties.The property was staked in September, 1923, by the late F. S. Arntfield. The early surface work was concentrated in the west part of the property along the Francoeur-Arntfield shear zone. The zone was opened by No. 1 shaft, which was sunk for an inclined depth of 250 feet. A series of silicified lenses were discovered farther east, where No. 2 shaft was later raised to the surface. A third shaft explored a shear zone about 1,900 feet to the east, where No. 3 shaft orebodies were developed.The mill was built at No. 3 shaft and production commenced in July, 1935, at 125 tons a day. This was increased to 280 tons by 1938, and later to 350 tons. The mine continued operations on this scale until April, 1942, when the exigencies of war necessitated closing. The Company was reorganized in 1944 and underground development was resumed in June, 1945. The total value of gold and silver produced to April, 1942, was $2,011, 755 from 529,987 tons of ore.ROCK TYPESThe area is underlain by highly deformed and altered Keewatin volcanics overlain by little deformed Cobalt sediments along the south boundary. The lavas in the vicinity of the mine workings are rhyolite, trachyte, andesite, and a flow breccia of intermediate composition. The fragmentals range from fine, well-bedded tuffs to coarse agglomerate in which acidic and basic horizons can be distinguished.The intrusive rocks are diorite and quartz-feldspar porphyry in the form of stock and sills, and narrow dykes of mica lamprophyre and syenite porphyry."

Jan 1, 1954

By B. Van den Bogaert, K. Binnemans, T. Van Gerven

Europium is one of the most critical rare-earth elements due to the limited supply of this element combined with a high demand for red lamp phosphors. Therefore, the recycling of europium from end-oflife lamp phosphors has become increasingly important. Photochemical reduction of europium(III) to europium(II) and subsequent removal from rare-earth mixtures by precipitation as EuSO4 is a very selective and efficient method to recover europium from binary europium/yttrium solutions. It is shown that full separation of europium and yttrium is feasible from laboratory prepared non-equimolar Eu/Y mixtures up to a ratio of 1/20, which reflect the composition of red lamp phosphors. Optimal conditions were determined at pH 4 with isopropanol as a radical scavenger, which is a less harmful and toxic compound than the commonly used formic acid scavenger. Europium removal efficiencies of more than 95% were achieved, with a purity of 98.5% of the EuSO4 precipitate. The irradiance of the used light source, expressed in mW/cm2, has a large impact on the illumination time needed to remove europium from the solution. It is observed that higher irradiance results in a shorter induction time, i.e. a period during which virtually no europium is removed, and a faster removal rate once the induction time has passed. The photochemical separation technique was applied to recover europium from leached industrial red lamp phosphor (YOX) powder, with a Eu/Y ratio of 1/30. Europium recovery of 50% was reached with a purity of 96%, proving the feasibility of this method for the recycling of europium from end-of-life lamp phosphors.

Jan 1, 2016

By E. G. Joe

"The continuing increase in costs for power and fuel are affecting significantly the cost for milling of Canadian ores. In order to ascertain the scope and source of energy consumption in Canadian mills for further energy conservation opportunities, CANMET, in cooperation with the Canadian Mineral Processors carried out a detailed survey on the metallic mineral processing plants. Sixty-seven mills representing almost 300 million tons of annual capacity participated in the survey. The results indicated that in general, copper and iron ore mills, representing the bulk of the tonnage, consumed relatively low levels of energy per ton. Nickel-copper, zinc-copper and lead-zinc ore mills were moderate in energy consumption, while uranium and some copper-lead-zinc mills reported much higher energy consumptions due primarily to the increased heat requirements of the ore pulp. While the plant heating costs varied somewhat with the location in Canada, it was apparent that the lowest heating costs were achieved by those built with proper insulation and energy conservation design. If the cost per million British Thermal Units is taken as $2.00, the mill energy costs generally ranged from 40¢/ton up to $1.20/ton.IntroductionEnergy consumption in milling has always been of significant interest to Canadian mineral processors who traditionally calculate their milling costs down to pennies per ton. Even the measure of an ore's grindability is expressed empirically by Bond in kilowatts hours per ton milled. Some of the mills located in isolated areas were obliged to generate their own electrical energy from fossil or petroleum-based fuel at a cost substantially higher than that obtainable from captive or public hydro-electric installations. These mills practiced energy conservation long before the advent of O.P.E.C. energy cost inflation. One example of this was the use of electric boilers to produce process and heating steam during off-peak electrical load periods."

Jan 1, 1978

By S. Pietruszczak, G. Su, T. S. Nguyen, E. Haghighat

"In this paper, the mechanical properties of Tournemire argillite are modeled using a mathematical framework which employs the microstructure tensor approach (Pietruszczak & Mroz, 2000). The experimental data incorporates the results of a series of triaxial tests (Abdi & Evgin, 2013) conducted at different orientation of bedding planes relative to the direction of loading. First, a plasticity framework is presented which involves the specification of the conditions at failure as well as the description of the irreversible deformation process. Later, a systematic procedure is outlined for identification of material functions/parameters involved. The paper is concluded by presenting the results of numerical simulations of the triaxial tests. It is demonstrated that the model can adequately reproduce the primary effects of anisotropy in the stable deformation regime as well as the onset of fracture.INTRODUCTIONThe understanding of the mechanical behaviour of argillaceous rocks is important in many types of geotechnical projects, including petroleum extraction, carbon dioxide sequestration as well as deep geological disposal of radioactive waste. In all these cases, the primary concern is the onset and propagation of damage due to excavation, transport of pore fluids and/or elevated temperature. The Canadian Nuclear Safety Commission (CNSC), Canada’s nuclear regulator, will be responsible for the licensing of future deep geological repositories. In order to evaluate the safety of deep geological repositories, CNSC staff keep abreast of scientific developments by collaborating with national and international partners on experimental and theoretical research on the long-term performance of those engineered and natural barriers. Through that collaboration, the CNSC has access to data resulting from experiments performed at different Underground Research Laboratories (URL). Such an URL is situated in Tournemire, France, in an argillaceous rock formation, the Tournemire argillite. The Tournemire argillite is characterized by the presence of closely spaced bedding planes and exhibits a strong anisotropic behaviour, so that its strength as well as deformation properties are directionally dependent."

Jan 1, 2015

By M. Connell, S. Bedrossian

Alkali cracking followed by chloride-based leaching is one of the prominent methods for rare earth element processing. Regeneration of the leach lixiviant, namely hydrochloric acid, is a critical operation in the process. A number of different process routes are available for recovery of hydrochloric acid from chloride solutions. The objective of this paper is to discuss various recovery routes and analyze the impact of several input variables on the variable operating cost.

Jan 1, 2014

By David J. Forrester

Light metals, most commonly aluminum, magnesium and titanium, and alloys containing them, are used in many industrial applications where lightness, hardness, ductility and resistance to corrosion are needed. However, these metals and their alloys can be potential ignition sources in underground coal mines. There have been documented cases in the past where coal mine explosions have been attributed to firedamp/coal dust ignitions involving light metals or their alloys. When light metals and their alloys are brought into contact with oxygen bearing material, such as iron oxide (rust) in the presence of heat, then a "thermite" reaction can occur. This source of heat can be generated from frictional contact or from merely a glancing blow. This paper outlines the hazards associated with light alloys, how to address the hazard and regulatory aspects.

May 1, 2001

By Wouter Bleeker, Isabelle Cadieux

"Abstracts of theses related to mineral deposit studies and exploration, completed at geology or earth science departments of Canadian universities, have been compiled for the period 1991 to mid-l993. Part I, presented in the June 1994 issue of the CIM Bulletin, gave a listing of thesis titles. Part II, which consists of edited abstracts of these considered to be of direct application to mineral deposit studies and exploration, is presented under various themes as follows;A. Kimberlites, Other Alkaline Intrusions and Related Studies;B. Volcanogenic Massive Sulphide Deposits and Related Studies;C. Mineral Economics;D. Mesothennal Gold Deposits, Other Gold Deposits and Related Studies;E. Magmatic Nickel-Copper, Platinum Group Element, and Chromite Deposits and Miscellaneous Platinum Group-related Studies;F. Granite and Pegmatite-related Deposits and Porphyry Deposits;0G. Diverse Hydrothermal Deposits, Sediment-hosted Copper Deposits and Mississippi Valley Type Lead-Zinc Deposits; andH. Uranium-related studies, Evaporites and Exploration GeophysicsAbstracts related to themes A. B and C are presented in this issue; the remaining abstracts will be presented in future issues."

Jan 1, 1994

By Xian Jian Guo, Lei Li, Hua Wang

Direct smelting of copper concentrate to blister copper has the advantages of energy saving and environmental protection. There has been a lot of effort invested in process development including test work and theoretic analysis in the past half century. However, the process has only been applied commercially to a few smelters that treat chalcocite types of copper concentrate. The main limitation to treating chalcopyrite types of copper concentrate is high copper content in smelting slag and low direct copper recovery. Thus intensive slag cleaning is needed. In this paper, the thermodynamic analysis was mainly carried out for the multiphase equilibrium of direct to blister copper smelting for both chalcopyrite and chalcocite concentrates. The practical problems in direct to blister copper smelting, which are mainly in copper content in slag, are clarified. The operational window of slag composition for different temperatures and oxygen partial pressure for the treatment of chalcocite type concentrates is identified. The process operation optimization for the blending of chalcocite, pyrite and chalcopyrite concentrates was done. INTRODUCTION The extractive metallurgy of copper can be divided into two broad groups of processes, namely, pyrometallurgy and hydrometallurgy, and the former is dominant. About 80% of copper in the world is produced by pyrometallurgy (Christopher et al., 2006). The first stage of conventional copper pyrometallurgy processing is to smelt copper concentrate to copper matte composed of FeS and Cu2S with slagging to remove a proportion of the iron (Gargul, Boryczko, & Bukowska, 2017). The smelting processes include bath and flash smelting. The second stage of the process is to convert copper matte to blister copper. In most cases, the copper matte is converted in Peirce Smith (P-S) converters, which are batch operations (Kubiszewski, 2015). The P-S converting can be divided into two periods, slagging and copper blowing. During slagging period, FeS in copper matte is oxidized to FeO, which reacts with silica flux forming slag. When the iron content in matte is less than 1%, copper begins to oxidize and reduce to form blister copper (Kucharski, Sak, Madej, Wędrychowicz, & Mróz, 2013).

Jan 1, 2019

By J. L. Chakravarty, S. K. Dutta, S. Banerjee, D. Putatunda

"General purpose uniprocessor systems used in control applications, however fast they may be, at a certain stage attain saturation, forcing the user or designer to consider other avenues for solving the problem. This paper gives a broad overview of multiprocessing with special reference to transputers. Virtually all aspects, from parallel systems real-time control to artificial intelligence (AI) and expert systems, have been highlighted. The application of transpurters in unilayer and multilayer control are discussed in detail, with specific attention to sensor integration. Two case studies describe at length the utilization of transputers. IntroductionIn conformance with the high level taxonomy of parallel computer architectures as given by Ralph Duncan(l) (an improvement to Flynn's classification, which maintains the essential elements of useful taxonomy based on instructions and data streams), the MlMD architectures are categorized into two groups: (I) shared memory, and (2) distributed memory type. While the shared memory multiprocessors are more popular than the message-passing multiprocessors because they can be programmed in a conventional sequential fashion, their aspect of the architecture creates a perfonnance bottleneck. In contrast, message-passing multiprocessors (MPM) suffer from no such limitation and can attain linear speed increases that are directly proportional to the number of processors put into use. The MPM implementation also has its own advantages and disadvantages. Because the performance of the system is heavily dependent on it, the interconnection strategy in a distributed memory MIMD machine is of paramount importance. The transputer(2.J), a multiprocessor node of the distributed memory type, is becoming very popular. The advantages offered by the transputer make its application in the mining and processing industries very promising."

Jan 1, 1994

By Charles G. Kemsley

IN view of the truly remarkable development of special steels for special purposes, the mining industry has for years looked forward to a time when steel makers would come forward with a product which would be an improvement over the straight carbon steel which has always held the field for drilling rock. In order to avoid making changes in conventional shop practice, the industry has perhaps been too insistent upon obtaining a water hardening steel which could be handled in the blacksmith shop by long established methods. As early as 1932 or 1933, an oil-hardening tool-steel of the one per cent carbon, plus chrome, plus molybdenum type was applied to hollow drill steel. It was known as a hard as well as a tough steel, and one that, theoretically, should give a good account of itself as a rock drill, if properly heat-treated; and so it has proved in actual trials. There were numerous deterrents which retarded adoption of this steel. For several years there has been a constant improvement in the drilling qualities of the straight carbon steel, and, considering the higher unit price ? of the alloy, there has been considerable doubt in the minds of some mining? men as to what advantage there might be in the use of alloy over straight carbon for hollow drill steel. The alloy being an oil-hardening steel, its adoption meant having two kinds of steel in the mine, for a time, and that spelled trouble, unless some positive means of identification was adopted. The hardening and forging ranges of alloy steel being narrow also made necessary much closer control over these operations if poor results were to be avoided. These thoughts undoubtedly prevented its use becoming wide-spread, for, as a matter of actual record, less than fifteen per cent of all the hollow drill steel used in Canada today is alloy.

Jan 1, 1942

By Bryon Bisiaux, Walter Valery, Sonny Mwansa, George Amonoo, Adrian Dance

"Newmont Ghana Gold Limited’s Ahafo operation have been working with Metso Process Technology & Innovation (PTI) since early 2009 to increase mill throughput from a combination of controlled blasting practices and optimised primary crusher and grinding circuit conditions. For such Mineto-Mill projects, PTI’s methodology is termed Process Integration & Optimisation (PIO).Ahafo operate a SAG mill, ball mill and pebble crusher (SABC) circuit that processes a range of primary ore of varying hardness from different pits which is blended with soft oxide material. The PTI study focussed on ball mill limited material from the Apensu open pit.Following a benchmarking study of all blasting, crushing and grinding practices in January 2009, PTI recommended changes in both blasting and crushing conditions in order to generate a finer feed size to the SAG mill. Additional operating changes in the grinding circuit were recommended.A series of trials were conducted in November 2009 where three blasts were fired using a different blast design (hole diameter and explosive type) in the same area of the Apensu pit as the benchmarked material in January 2009. Top and bottom benches (or flitches) from each blast were sent exclusively to the grinding circuit and the material was tracked using PTI’s SmartTag™ system.The results from the six trials showed a significant increase in primary ore throughput at a reduced blend of oxide material. Ahafo have since standardised on these modified blasting conditions for all Apensu ore zones and have been able to sustain higher throughput compared to historical performance on similar material.This paper summarises the phases of the PIO project, the changes made in operating practices and the outcomes of the blasting trials that validated the predicted increase in mill throughput."

Jan 1, 2012

By Colin E. Dunn

Plants have a remarkable ability to select, use and store metals derived from the substrate. Each species is unique in its requirements for and tolerances to the full spectrum of chemical elements in the Periodic Table. Studies to define the chemical characteristics of common trees and shrubs of the temperate forest are providing insight to their use for exploration, i.e., biogeochemical exploration. Examples of surveys over gold deposits in British Columbia show the effectiveness of sampling various tissues from different species in a range of biogeoclimatic environments. At the Nickel Plate mine in the Montane-Spruce zone, outer bark of Lodgepole pine was effective in defining a large area of metal enrichment; at the Carolin mine in the zone of Coastal Mountain Hemlock, analysis of twigs of western hemlock and Pacific silver fir provided an exploration target considerably larger than that defined by lithogeochemistry; at the Mount Washington gold deposit in the Mountain Hemlock zone, twigs of mountain hemlock and rhododendron were used to outline the mineralization; and in the Interior Douglas-fir zone at the QR deposit analysis of Douglas-fir tops collected by helicopter provided a rapid and effective method of identifying a gold-rich area.

Jan 1, 1995

By Colin E. Dunn

Abstract-Plants have a remarkable ability to select, use and store metals derived from the substrate. Each species is unique in its requirements for and tolerances to the full spectrum of chemical elements in the Periodic Table. Studies to define the chemical characteristics of common trees and shrubs of the temperate forest are providing insight to their use for exploration, i.e., biogeochemical exploration. Examples of surveys over gold deposits in British Columbia show the effectiveness of sampling various tissues from different species in a range of biogeoclimatic environments. At the Nickel Plate mine in the Montane-Spruce zone, outer bark of Lodgepole pine was effective in defining a large area of metal enrichment; at the Carolin mine in the zone of Coastal Mountain Hemlock, analysis of twigs of western hemlock and Pacific silver fir provided an exploration target considerably larger than that defined by lithogeochemistry; at the Mount Washington gold deposit in the Mountain Hemlock zone, twigs of mountain hemlock and rhododendron were used to outline the mineralization; and in the Interior Douglas-fir zone at the QR deposit analysis of Douglas-fir tops collected by helicopter provided a rapid and effective method of identifying a gold-rich area.

Jan 1, 1995

By Brian K. Ayres

Inco Limited, Ontario Division is currently in the process of decommissioning the Whistle Mine site located near Sudbury, Ontario, Canada. The most significant component of site decommissioning involved relocating approximately 6.4 million tonnes of acid-generating waste rock to the open pit from two adjacent stockpiles. An engineered cover system was designed for the backfilled pit to reduce the long-term production of acid rock drainage. Geochemical modelling was conducted to assess the effectiveness of various cover options on the longterm water quality of the backfilled pit. Results obtained from performance monitoring of cover system field trials at the site and estimated full-scale construction costs were used to select an appropriate material for the cover system barrier layer. The two-dimensional soil-atmosphere model VADOSE/W was used to develop a calibrated model of covered waste rock based on field data obtained from the cover trials, which was subsequently used to predict net percolation and oxygen ingress through various cover system alternatives for site-specific climate conditions. Erosion and landform evolution numerical modelling was completed to assist in designing the runoff management system and final landform for the pit cover system. The potential impact of various physical, chemical and biological processes on the sustainable performance of the pit cover system was also considered in the design process. This paper provides an overview of the design and construction of the backfilled pit cover system.

Apr 1, 2005

By J. C. Ingles

"A survey of possible methods for controlling cyanide concentration indicated that the simplest method would involve the use of a potentiometric technique. Such a method was suggested by a paper from the laboratory of Mines Safety Appliances, which described a method for determining hydrogen cyanide in air. In this application, the cyanide was absorbed in caustic and a silver electrode immersed in the caustic solution provided a measure of the cyanide concentration. However, our attempts to use the silver electrode in this simple manner to measure the cyanide concentration of solutions were not very successful. A study of the mechanism by which a silver electrode responds to cyanide concentration made it evident why this simple procedure is not satisfactory.Basically, the silver electrode provides an indication of the free silver ion concentration of a solution, and generally speaking, ignores the other ions' present. It can be used to measure an anion if this anion complexes silver. This technique has been used in complexing studies to determine the activities of such anions as acetate, citrate, oxalate and chloride. To do this, the electrode has to be placed in a solution which initially contains a known concentration of free silver ions. Addition of the complexing anion causes a drop in the free silver ion concentration and hence a change in the potential of the silver electrode. The change in potential can be expressed in terms of the concentration of the complexing anion, and used to indicate its concentration in the solution being analysed. The determination of chloride-ion by a silver-silver chloride electrode is an example of an application of this technique. The solubility of the silver chloride with which the electrode is coated provides the initial free silver-ion concentration. Depression of this free silver-ion concentration by the presence of the excess chloride ion of the sample solution results in a change in the potential of the electrode which is proportional to the chloride-ion concentration."

Jan 1, 1965