Search Documents

By Dwayne D. Tannant

The Fox Pit at EKATI Diamond Mine reached a depth of approximately 150 m as of September 2005. The pit is designed with 11 m wide benches excavated using a double benching technique leaving 30 m high bench faces. A series of blasting tests were conducted to improve catch bench reliability and increase the percentage of benches that meet an 11 m catch width. The design changes focussed on reducing damage to the bench crest because maintaining the bench crests is the most important factor in achieving good bench reliability. The most significant improvement was obtained by raising the bottoms of the lower trim blastholes by 0.5 m. This change decreases the depth of broken rock below the final bench elevation, and consequently reduces damage to rock that forms the bench crest below. Another improvement was the use of smaller diameter (165 mm vs. 270 mm) blastholes in the A and B rows for the upper trim blast. This change reduces the charge per delay during detonation, reduces the powder factor slightly, and reduces the energy affecting the final pit wall and crest. As mining and the blast testing progressed, the portion of the bench with crest achievements (>11 m) increased from 57% to 75%.

May 1, 2006

By Kosei Ishida

To achieve renovation work without noise, the authors developed techniques of manufacturing pre-cut interior finishing components for renovation work. In this paper, to achieve the system of pre-cut interior finishing components, the authors describe a measuring method of reinforced-concrete structure by 3D laser scanner and then describe a method of making a design of pre-cut interior finishing components with the polygon model. Using these two methods, the steps of manufacturing pre-cut interior finishing components consist of the following four steps: First, measure the building shape using a 3D laser scanner. Secondly, integrate a point cloud data and retrieve the markings on the floor. Then, create a polygon model of the building based on the point cloud data. Lastly, make a drywall design using a polygon model. To evaluate the technique feasibility of manufacturing pre-cut interior finishing components, the authors have conducted an experiment of the finishing interior work of the drywall. Using pre-cut interior finishing components, the authors have been able to achieve interior finishing work without noise.

Aug 1, 2013

By C. Hari Manoj Simha, J. Gholipour, M. J. Worswick

Due to the high pressures involved in the hydroforming process, friction and lubrication play an important role and can affect formability of the material. Tubes of A1Mg3.5Mn aluminum alloy, of 76.2 mm (3 inch) outside diameter and 2-mm thickness were considered in this study. Three kinds of lubricants, Al070, Hydrodraw711 and water, were applied to the tubes and tubes were hydroformed to burst in a square shape die cavity. The key process parameters were recorded during the tests. An in-house Gurson-Tvergaard-Needleman (GTN) damage-based material model, implemented in LS-DYNA, was used to model the process and predict the formability of this material. The applied axial loads and internal pressures recorded during the tests were used in the computations. The effect of different types of elements (solid and shell) with different constitutive models (von Mises and GTN models) in predicting the strain distribution is studied. The GTN damage-based material showed a good ability to capture necking and displacement histories in this process. Both predicted and measured results showed that the lubricant with lower coefficient of friction can effectively increase the comer expansion.

Jan 1, 2006

AGENDA ? Company Overview ? Industry Direction ? Technology to support maintenance ? data access, connectivity, process historian, downtime & production reporting. ? Case Studies Company Overview Corporate Offices Client Base ?16 consecutive years of growth & profitability ?#39 of Top 50 Control Companies (Worldwide) ?470 employees ?TSX: MTK Industry Direction Improved visibility into the business so they can: ? Reduce cost through better understanding of where costs are being incurred and making timely decisions. ? Optimize operations while leveraging existing assets. ? Have a single version of the ?truth? ? Deliver reliably to stakeholders on the demand for increased accountability (safety, environmental, regulatory performance etc?). ? Respond quicker to market conditions in order to out perform the competition ? Best in Class approach. Web is becoming the standard user interface.

Apr 1, 2005

By Louise Corriveau

A Targeted Geoscience Initiative transect in the eastern Grenville Province reveals an extensive VHMS-style cupriferous hydrothermal system among rhyolitic pyroclastic rocks of the Wakeham Group at La Romaine, Québec. The volcanic rocks outcrop sporadically along a < 10 km-wide by about 100 km-long belt correlated with the south-eastern extension of the Wakeham Group. This belt occurs among voluminous, magnetite-bearing, granitic gneiss. At Lake Musquaro, 1.51 Ga metarhyolitic to dacitic lapillistones and flows, locally with aluminous nodules and veins, are intruded by 1.49 Ga feldspar porphyries. This volcanic package was deposited on typical Wakeham Group arenite (< 1.52 Ga) interbedded with nodular, muscovite- and fibrolite-bearing gneiss, and minor marble hosting finely layered garnetiferous hornblendite, garnetite and magnetite-bearing coticule. The latter are interpreted as meta-exhalite and with the associated albitite (sodic alteration), aluminous veins (hydrothermal leaching) and magnetite-rich granitoids, they are key elements in the search for concealed mineral deposits in this area. At La Romaine, to the south, 1.5 Ga lapillistones outcrop structurally above metasediments and below a composite amphibolite unit of uncertain origin (lava or sills) with magnetite-rich (BIF?) units. An extensive zone of aluminous gneiss, with lapilli textures, provide evidences for severe hydrothermal leaching of the volcanic rocks prior to metamorphism. An adjacent siliceous vein-textured unit likely represent a zone of intense silicification (74 wt.% SiO2), while aluminous, hematite to magnetite-bearing veins in adjacent felsic gneiss (tuff?) preserve evidences for the sequence of alteration events. Despite granulite-facies metamorphism, the main characteristics of the amphibolite unit persist along the entire belt. This competent unit likely served as a cap rock; the garnetite, diopsidite and hornblendite it hosts provide effective guides to the sites of fluid discharge and mineralization. A number of Cu showings, modest in size, were discovered in this unit. Their systematic occurrence, in a structural-stratigraphic sense, indicates that this setting is attractive for mineral exploration despite high-grade metamorphism and deformation. Late-stage veins laden with fluorite crosscut these alteration zones, and are themselves metamorphosed, indicating that hydrothermal activity was polyphased. SHRIMP U-Pb ages obtained on detrital zircons (1 arenite) and on igneous zircons (5 volcanic rocks, 1 porphyry and 6 granitoids), pervasive arc-type geochemical signatures and presence of in situ rafts of barium-rich garnetite in the granitoids indicate that sedimentation and volcanism occurred between 1.52 and 1.49 Ga coevally with hydrothermal activity and emplacement of a sub-volcanic 1.5 Ga granitic batholith with early, 1.53 Ga tonalite intrusion. Such a geological context can sustain large-scale hydrothermal cells and development of VHMS, Cu-Fe oxides or SEDEX deposits.

May 1, 2003

By Youngsoo Song, Hyunjung Kim, Junhyun Choi, Siyoung Q. Choi, Gahee Kim

In this study, for the first time, to confirm the effect of bacterial growth phase on the malachite flotation were investigated in a well-controlled Hallimond tube system. The test results showed that the bacteria in the stationary phase exhibit two-fold greater floatability than those in mid-exponential phase. To understand the observed flotation behavior, complementary cell characterization tests and cell attachment tests were conducted. Interestingly, the bacteria at both phases exhibited similar surface properties as well as almost identical amount of cells attached onto the malachite, suggesting that the growth phasedependent flotation behavior cannot be attributed to the variation of cell surface properties and the extent of cell adsorption. On the other hand, cell detachment tests revealed that the amount of cells detached from the malachite surface is greater for the mid-exponential phase than the stationary phase due to the higher fluid drag applied to the cells at the mid-exponential phase, which was explained by the differences in the size and shape of attached bacteria onto the malachite surface. These morphological characteristics were found to cause the bacteria of mid-exponential phase to be separated highly sensitive and easy from malachite surface due to the fluid flow. Second, scale-up selective bioflotation tests were carried out in a 1 L Denver cell in malachite–silica binary mixture systems. Through the tests, we optimized the cell concentration and the malachite fraction in the feed. Overall, high malachite selectively was observed under optimized conditions (both recovery and grade showed more than 90%). The trend was in agreement with classical DLVO interaction energy profiles, which show the relative magnitudes of the adhesive forces between the mineral and the attached cell under equal hydrodynamic conditions.

Jan 1, 2016

By M. S. Moats

"The effects of commercial copper electrorefining additives (glue and thiourea) on the electrochemical removal of bismuth are of importance in copper production. It was found that Bi(III) electrodeposition occurs readily from acidic sulfate solution via a diffusion-controlled quasi-reversible reduction. The diffusion coefficient of Bi(III) was measured and found to be less than reported values of copper in similar solutions. The presence of thiourea and/or glue was found to accelerate or de-polarize Bi(III) reduction on stainless steel as compared to the inhibition or polarization of Cu(II) reduction. The additives also inhibited the dissolution of the Bi-Cu co-deposit during cyclic voltammetry. During short term deposition studies, the additives increased the concentration of Bi in co-deposited Cu-Bi products from solutions with low concentrations of Cu (<2 g/L). Bi deposition was significantly suppressed by increasing the Cu(II) concentration in the solution. The formation of a copper layer on the stainless steel electrode appeared to significantly suppress the reduction of Bi(III). This study demonstrates that glue and thiourea depolarize the deposition of bismuth on stainless steel. Therefore, the additives could be used to improve Bi impurity removal during third stage liberation.INTRODUCTIONThe production of high purity copper has been steadily increasing due to the wide application of the metal and its alloys in electrical and electronic products, infrastructure construction, industrial machinery and equipment, general products and transportation (Moskalyk et al., 2003). Most high purity copper is manufactured from copper sulfide mineral concentrates and/or scrap via a pyrometallurgical process followed by electrorefining (Navarro et al., 1999). During the electrorefining process, cast anodes of 99-99.5% purity are electrochemically dissolved into an acidified copper sulfate solution while high purity copper (>99.99%) is plated on stainless steel blanks or copper starter sheets (Davenport et al., 2002). The control of cathode deposit growth (purity and morphology) while maintaining a high current efficiency is of significant importance for copper refining (Ilkhchi et al., 2007). At typically applied current densities for industrial copper electrorefining, mass and charge transfer play important roles in the quality of cathodic products (Hiskey et al., 1998). If the real current density at some surface points is substantially higher owing to uneven current distribution, then rough spots can and will grow faster leading to nodules (Suarez et al., 1992). Nodulated deposits tend to capture solution and anode impurities (slimes) resulting in unacceptable cathode quality (Afifi et al., 1987). Furthermore, these nodules can grow until they eventually contact the anode leading to short circuits and current efficiency reduction (Ilkhchi et al. 2007)."

Jan 1, 2016

By Vlad Ruzicka

"Uranium deposits in the Rabbit Lake-Collins Bay area are associated with the sub-Athabasca unconformity which separates crystalline Archean or Aphebian basement rocks from Helikian clastic sedimentary rocks of the Athabasca Group. The basement rocks are a part of Wollaston lithostructural domain.Most of the high grade deposits, such as Collins Bay ‘A’ and 'B' Zones and Eagle Point are associated with altered rocks of the basal unit of the Wollaston Group. Some deposits, such as Raven and Horseshoe are confined to the uppermost unit of this Group. The Rabbit Lake deposit occurs in the middle, meta-arkose unit of the sequence. Locations of some deposits (Rabbit Lake, Collins Bay ‘A’ and 'B' Zones) are also controlled by thrust faults, such as Rabbit Lake Fault and Collins Bay Fault.The deposits contain either monometallic (uranium) mineralization (Rabbit Lake, Raven, Horseshoe) or polymetallic (mainly uranium-nickel) assemblages (Collins Bay “A’ and 'B' Zones).IntroductionThe Athabasca Basin region, a part of the Churchill Geological Province of the Canadian Shield, is composed of Archean and Aphebian crystalline basement and younger, Helikian, unmetamorphosed supracrustal rocks. The Rabbit Lake-Collins Bay area is situated at the eastern margin of the Athabasca Basin region, which hosts a substantial proportion of Canadian uranium resources.The crystalline basement complex was subdivided by Lewry and Sibbald (1979) into lithostructural domains and these domains were grouped into major crustal units designated, from northwest to southeast, as Western Craton, Cree Lake Mobile Zone, consisting of Wollaston, Mudjatic and Virgin River domains, and Rottenstone Complex (Fig. 1)."

Jan 1, 1986

By Jianhong Xu, Hailong Hou, Yu Jing, Yundong Wang

Microcapsules containing extractants have been applied to the extraction of metal ions, organic acid, pesticide, and herbicide. The difficulties of conventional liquid-liquid extraction in phase mixing and phase separation (e.g. high energy consumption, emulsification phenomenon, and large equipment requiring housing) could be overcome in a liquid-solid system by using microcapsules. Even some extractants with high viscosity and poison can be encapsulated conveniently into microcapsules. In the work described in this paper, polysulfone microcapsules containing 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (P507) were successfully prepared. Then, the extraction rate of lanthanum, samarium, and erbium in dilute solution into the microcapsules containing P507 was studied. An extraction kinetic model is proposed based on the interfacial reaction model accompanied by intraparticle diffusion expressed by Fick’s law. The extraction efficiency was obtained by using the kinetic model with the separately determined complex formation rate constant and the intraparticle diffusion coefficient. From the results, it was confirmed that the kinetic model could predict the experiment in a microcapsule system over a wide concentration range of lanthanide solution. In the future, the model could provide good guidance for the design and application in extraction of lanthanides.

Jan 1, 2014

By J. Oliveira, A. R. Barnes, R. Pandher

Sub-stoichiometric roasting of arsenic-bearing copper ores is a well established practice. However, ores containing calcium commonly prove challenging where very low arsenic levels are desired, but the reasons for this phenomenon have largely been speculative. In the course of treating arsenicbearing copper ores by partial roasting in fluid bed reactors, XPS encountered one of these Ca-bearing ores which proved a challenge to roast to acceptably low levels of arsenic. Mineralogical examination of the calcines using a combination of XRD (X-ray diffraction), QEMSCAN (Quantitative Evaluation of Materials by Scanning Electron Microscope) and EPMA (Electron Probe Micro-Analysis) helped to identify the arsenic bearing species and assisted in developing a workable theory on the sequence of reactions occurring during the roast. With the assistance of thermo-chemical modelling, this allowed adjustment of the roasting conditions to minimise the amount of arsenic retention in the calcine in spite of the presence of calcium in the ore and advance the roasting program to a commercially acceptable solution.

Jan 1, 2014

By J. Sugai

Formability of extruded round AZ31 magnesium alloy tubes with different manganese concentrations was evaluated by performing bending tests and measuring strain along the length of the tubes during the bending process. It was found that an increase in the manganese content from 0.3 % to 0.7% did not exert any significant effect on the values of yield stress, elongation, or compression to fracture. However the hardness tended to increase and the UTS decreased. The compressive ductility was significantly lower than tensile ductility for all manganese concentrations. Consequently, the formability of tubes decreased, causing cracks in areas where compression strain occurred during bending. It was also found that a larger strain occurred in the latter half of the region along the length of tube between the clamp-end and the tube-positioning block. Within this region, alloy tubes with higher manganese concentrations, 0.5 and 0.7 %, there was a clear strain peak within the strain profile, while for the 0.3 % Mn alloy, a more uniform strain profile was exhibited, indicating a more uniform deformation. This was confirmed by microstructural analysis of the specimens.

Jan 1, 2006

"Classification is an important aspect of mineral processing plants and if not operated efficiently can compromise both the throughput and recovery of the circuit. This paper discusses the benefits that can be obtained by operating the classification section efficiently. Since classification in most of the mineral processing plants is carried out using either hydrocyclones or screens the case studies involving the two classifiers were used in the discussion. Studies where optimising the classification circuit lead to improvements in the performance of the overall plant were included to show the benefits of paying attention to this area that is usually neglected. The data from the mill-float mill float, SABC, and Single Stage SAG mill circuit case studies have shown that the circuit throughput can be increased throughputs without compromising recoveries by optimising the classification circuit. On plants where the ore can be liberated at coarser sizes the experimental results have shown that replacing hydrocyclones with high frequency screens can lead to improved plant throughput with no detrimental effect on recovery. The discussion has included information on design and operational considerations for plants that have or intend to use hydrocyclones or screens that could make the classification circuit more efficient.INTRODUCTIONComminution is the process in which particles are reduced in size mainly by crushing and grinding. In most mineral processing circuits comminution is carried out to liberate the valuable minerals prior to subjecting the ore to a recovery process were values are concentrated or extracted (Mainza, Evertsson, Benzer, Tavares, Powell, Rule, Plint, …, 2013). Comminution is an energy intensive process and is usually achieved in stages. It is common to have a classifier after each comminution stage. The process is carried out in stages to minimize energy usage and to improve the efficiency of the process in meeting product specifications. Although comminution circuits have been advancing classification has remained a key component of the comminution circuit design (Mainza et al., 2013). Mainza et al. (2013) summarised the role of classification in mineral processing circuit as: to allow material in the equipment that can promote high operational efficiency, to improve material handling in the circuit, to minimize overgrinding of material to reduce energy consumption, and to provide the best quality product to enter the next stage of processing. Classification stages are employed in comminution circuits to ensure that high throughputs are processed without compromising the product quality or to produce a fine product at relatively low energy. If neglected classification can have detrimental effects on plant performance."

Jan 1, 2016

By Y. M. Shneerson, P. V. Zaytsev, I. V. Fomenko, M. A. Pleshkov

A thermodynamic description of the equilibrium in liquid and gas phases under specific conditions of refractory gold pressure oxidation was generated using the HKF theory. The gold behavior was considered at 190-225°C in the presence of 1-100 mg/L of chloride ion, and under oxidationreduction potential (ORP) of +700 to +1030 mV. The calculations show that the predominant form of gold(I) occurrence is [AuOH]° compared to [AuCl2]?. High ORP favors the formation of [AuCl4]? as a predominant form of gold(III). It is noted that this complex is responsible for the gold losses buildup during POX. Laboratory test results for double refractory concentrate POX are shown. The combined negative effect of (i) organic carbon of the concentrate and (ii) dissolved chlorides in POX slurry on gold recovery is demonstrated. The effects of carbonate blending to the POX feed concentrate and incomplete oxidation of sulfides on POX performance were studied. The pilot tests results of continuous pressure oxidation are also shown and generally confirm the laboratory results and theoretic dependencies. A comparison of the experimental data with the results of thermodynamic calculations is made. As a result of current research, an effective process for POX treatment of carbonaceous sulfide concentrates in the presence of chlorides was developed.

Jan 1, 2014

By J. Brent Hiskey

At present, approximately 80 % of the worlds mine production of copper is achieved by smelting and electrorefining. The principle aim of copper electrorefining is to satisfy the large demand for extremely pure copper. It is remarkable that high quality copper cathodes with the required purity (99.99+% Cu, ASTM B115-10) and structural characteristics (i.e. deposit density and morphological texture) are produced from impure copper anodes dissolved in electrolytes containing a variety of impurities. This is accomplished with the proper control of operating parameters such as: current density; temperature; copper and sulfuric acid concentration; agitation; substrate preparation; and the application of electrolyte additives. The basic elements of the electrolysis of copper have not changed significantly over the past 150 years since the early developments of James Elkington. Importantly, our fundamental understanding of the underlying electrochemistry has advanced considerably. This is especially true regarding our knowledge of the mechanistic role of additives during the electrocrystallization of copper. This is a very complex subject and modern electrochemical techniques and the development of surface characterization and imaging instruments has helped immensely in our ultimate understanding of how additives control the deposit structure and morphology. The purpose of this paper is to review the historical development and application of electrolyte additives in copper electrorefining and to examine our current knowledge regarding their use. INTRODUCTION The first transatlantic telegraph cable was completed in August 1858. Regrettably, this cable failed shortly after the initial connections. After several more failed attempts, improvements in materials and copper quality resulted in successful communication between Europe and America on July 28, 1866. In many ways this hallmark event demonstrated the need for high purity copper. The first copper refinery in the world was commissioned in May 1869 in Pembrey, South Wales by partners Josiah Mason and James Balleney Elkington. (Historical Note). The 1865 and 1868 British patents issued to James Balleney Elkington were the foundation for the first commercial production of high purity electrolytic copper (Elkington, 1865, 1869, 1870). This important achievement was made possible primarily by the invention of the dynamo which was based on the fundamental operating principles advanced by Michael Faraday. A symbiotic relationship between copper refining and the dynamo was henceforth established. The dynamo provided electric current for electrolytic refining of copper and the electrorefining tankhouse provided pure copper which was required for the generation and transmission of electricity.

Jan 1, 2019

By S. M. J. Mirazimi, F. Rashchi

Recovery of vanadium from LD (Linz-Donawits) converter slag was evaluated by means of microbial leaching. Vanadium leaching was performed in two stages. In the first stage, the bacteria were grown in a culture medium and in the second stage; vanadium containing slag was added to the metabolites produced by bacteria. Bioleaching was performed using heterotrophic bacteria Pseudomonas Putída. Control tests without bacteria inoculation were also performed and the results were compared with bioleaching outcomes. Optimal conditions for the bioleaching of vanadium containing slag were determined.

Jan 1, 2011

By David Meadows, Elmer Palmer, Steve Dixon

As part of the Goldcorp Inc growth plan Minera Peñasquito SA de CV has developed its polymetallic deposit with a large “state of the art” concentrator to process lead and zinc ores. The plant consists of two grinding lines including 38ft diameter SAG mills and 24ft diameter ball mills. During mid to late 2009 concentrator commissioning activities commenced. First concentrates were produced in October 2009 and now the plant is meeting its design basis of 65,000 mtpd per line. This paper describes the design and operational experience to date for its grinding circuit design, together with the recently commissioned HPGR crushing circuit.

Jan 1, 2012

By Rolf Andreas Lauten, Guy Kluck

"Formation of scales may have important detrimental effects in many mineral processing applications. A well-known problem is the need for frequent maintenance to remove scale from processing equipment. Another challenge may relate to encapsulation of valuable minerals in precipitating scale. In this work, we explore the ability of some crystal growth inhibitors to prevent or lower the degree of scale precipitation. In many situations pregnant leach solutions contains substantial concentrations of calcium, magnesium, sulfate and carbonate in addition to dissolved valuable elements, e.g. gold, copper, zinc. Together with non-dissolved gangue minerals, some slurries may also contain particulate gold, copper etc. During normal processing of the pregnant leach solution it may be exposed to temperature gradients or similar promoting precipitation of various scales. Valuable minerals may become entrapped in precipitates and thus become inaccessible to the lixiviant. Use of a crystal growth inhibitor may lower the degree of encapsulation of valuable elements.Using a simple model system, supersaturated with respect to gypsum, the effect of some crystal growth inhibitors on the prevention of scale is evaluated in terms of amount precipitated gypsum, the particle size of the precipitated gypsum and the carbon gold loading capacity.INTRODUCTIONGold bearing sulfide ores are often roasted or pressure oxidised prior to leaching. The purpose of this unit operation is to prevent loading the leaching circuit with sulfides that consume cyanide. Pressure oxidation or roasting chemically converts the sulfides into sulfates and at the same time, the pH of the slurry ends up in the acidic range. Typically, lime addition is the preferred means to raise the pH to around 10 where gold leaching takes place. Combination of large amounts of calcium ions from the lime with sulfate ions from the ore induces precipitation of gypsum. Compounds like calcium carbonate may also precipitate if carbonate ions are present in the slurry. Depending upon the composition of the ore, compounds like calcium carbonate and other types of scale may also precipitate on gold surfaces on the slurry particles. A layer of scale on top of exposed gold surfaces will prevent dissolution in the cyanidation that takes place during leaching. Naturally, such a precipitation may lower the gold recovery."

Jan 1, 2016

By Murray W. Grabinsky

The in situ performance of Cemented Paste Backfill (CPB) systems can be monitored to improve understanding of the paste?s behaviour and therefore optimize the geomechanical design of the cemented paste backfill system (i.e., minimize binder content, minimize fill barricade complexity, maximize fill rate-of-rise during backfilling, and minimize cure time before resuming production blasting in proximity). However, undertaking such a monitoring program is inherently complex, because the rate-of-rise and accompanying self-weight induced stresses occur at a time rate that is similar to the rate of hydration and associated increase in the paste?s stiffness and strength. In addition, arching within the stope complicates the overall stress distribution. Therefore, to obtain a complete picture of the CPB?s response, it is necessary to measure several variables (3-D total pressures, water pressures and suctions, hydration rates, and blasting induced vibrations) at a given ?point?, and take all such measurements at many points throughout the fill mass as well as at barricade locations. The overall testing program can therefore be logistically difficult to implement and have an apparent high cost. However, if the program is successful, the benefits arising from improved mine design can significantly outweigh the seemingly high initial capital and labour costs of the monitoring program. A case study involving an instrumented paste fill in a tall and narrow Alimak stope is briefly outlined. Plans for a similar experiment in a large long-hole stope are then considered.

May 1, 2008

By Guillermo Diaz, Roberto Pérez, René del Villar

"Pulp-froth interface position is a key variable in column operation. In plant practice, it is commonly estimated through a system of three pressure-transducers which allows the calculation of the pulp height. An alternate method based on the measurement of the conductivity profile across the interface has been proposed and successfully tested. Both methods however, present some practical problems related to the assumptions made in the calculation of the pulp height in the former case, and to the response time and the precision of the reading in the latter case.In this paper, the use of the neural network technique for improving the estimation of the pulp-froth interface in flotation columns is discussed. The technique is used with both conductivity-based and three pressure-transducer methods. Results obtained in a 2"" laboratory column and a 12"" pilot scale column are presented. A major obstacle in applying this approach in practise is the training of the artificial neural network. This problem is analyzed here for the conductivity-based method and some solutions are proposed."

Jan 1, 1995

By J .. R. Dalton

"Blasting in high sulphide content ores presents at least two major safety considerations: (1) compatibility of the explosives with the ore while resident in the borehole; and (2) introduction of a flame and shock producing explosive into this environment, while minimizing the risk of reactive ignition in the chemical reaction products/sulphide dust cloud resulting from the detonation. This paper will discuss only the second consideration, i.e. post detonation reactivity.The ETI (Explosives Technologies International) Technical organization, in consultation with the U.S. Bureau of Mines, reasoned that the most relevant considerations in the development of an explosive for this application are:• minimization of reactive gaseous detonation reaction products;• flame duration reduction;• flame temperature reduction;• increased explosive sensitivity;• reduced probability of ""low order"" detonation; and• maintenance of energy level as high as possible.Obviously, not all of these are totally independent properties, i.e. increased sensitivity will reduce the probability oj low order detonation as will higher energy levels. However, these considerations were examined separately as if they were independent."

Jan 1, 1994