Search Documents

By David G. Almond

"Economies of scale and the variable characteristics of many large ore deposits have resulted in grinding installations having large SAG mills fitted with variable speed drives. Problems associated with effective operation of this equipment has created the need for better operator knowledge of mill load behavior and the need for new instrumentation capable of providing accurate information about load movement and composition. This paper discusses two performance enhancing instruments available to address these needs.INTRODUCTIONThe economic demands of new mining projects has resulted in increased equipment sizes and this is particularly evident in milling where there are now many SAG mills operating in the range of 28’ – 40’ diameter with installed powers of 8 – 22 MW. These mills are designed to process very high capacities of ore daily2 and the variable characteristics of many of the deposits mined results in the need to vary the mill speed during processing to cater for the changes in ore hardness. Mill speed changes often result in operational problems associated with high-energy impacts striking the mill liners reducing energy efficiency as well as degrading the grinding media through breakage, accelerating liner wear and in extreme cases even breaking liners. These operational problems have given rise to the need to have instruments aimed at providing operators with accurate information in real time about the load composition and movement within SAG mills.The original concepts for operating SAG mills were derived from past experience of operation of conventional fixed speed ball mills. However, the relatively stable conditions that applies with fixed speed and constant ball charge in ball mills supports theoretical approaches to the grinding process based on energy calculations such as Bond’s Work Index concept. Later a set of parameters Si and Bij were used for describing load kinetics, but all of these methods neglect the details of load movement and how the energy is actually used inside of the mill. It is now commonly accepted as a basic rule that SAG mills grind by impact whilst ball mills grind by attrition and consequently SAG mills are designed and operated to generate a large amount of impacts by the cataracting load without paying sufficient attention to where these impacts are actually occurring. Many mills are operated on the basis that as long as the mill is consuming the expected power there is little attention given to the class of bodies using this energy and this often results in the inefficient use of energy."

Jan 1, 2005

By Valérie Tremblay

Plan de la presentation ?Laboratoire d?analyse des fluids ?Gestion des contaminants ?Condition Monitoring Avantages reliés aux analyses ?En savoir plus!! ?pour minimiser les coûts d?opération; ?pour prévenir les défaillances catastrophiques; ?pour maximiser le rendement des équipements; ?pour maximiser la longévitédes équipements; ?pour permettre des périodes d?entretien planifié.

Feb 1, 2008

By Masayuki Ishikawa

In a radio frequency and optoelectoronic device packaging, Gold-Tin (Au-20 wt% Sn eutectic) solder is used widely due to the excellent electrical and thermal conductivity, high strength, and negligible creep characteristic under repetitive thermal cycling. With the recent lead-free movement, Gold-Tin solder is recognized as an alternative material for high temperature Lead-Tin solder. Generally, Gold-Tin solder is supplied in the forms such as ribbons, pellets, and ring frames. However, these forms must be set-up accurately on the joint area to press chips in bonding, therefore, it is difficult for these forms to satisfy the recent requirements for the down sizing in the connection areas. On the other hand, Au-20 wt% Sn solder paste can be applied flexibly to various supplying methods, such as printing, dispensing system and pin transcript. These methods also make it possible to reduce the production cost. However, in the case of using the solder paste, the void issue is one of the most undesirable problems. The void causes the degradation of the characteristics such as the bond strength, electrical characteristic and thermal conductivity. We have been intensifying the development of the void free paste, and have achieved void reduction by optimizing the powder size, the flux composition and the reflow condition.

Oct 1, 2003

By M. Poirier, J. H. Mbouche

"The research question of the present work is the following: at which speed should a rotary sample divider operate in order to produce representative samples of iron ore concentrate? In order to solve this problem, the representativity of a rotary sample divider treating iron ore concentrate from Iron Ore Compagny (IOC) Carol Lake mine in Labrador City was studied in the laboratory of mineral processing of “CEGEP de Sept-Îles”. The rotary sample divider speeds tested are: 20, 40, 50, 60, 80 and 100%. The results show differences in both weight and particles sizes distributions with respect to the various rotation speed used. 20% has shown to be the speed that generates an almost normally distributed samples for both weight and particle size. As the speed of the rotary sample divider increases, the polygon of frequency for weight distribution progressively becomes a two modal distribution curve. 40, 50 and 100% speeds generate normal samples distribution curves with respect to particles size only. 60 and 80% are the speed to be avoided since they generate multiple modal distribution curves for both weight and particles size.IntroductionIn the mining industry, samples representativity is part of the key elements for management decisions. In fact, “Sampling provides vital information to plant operators, clients and geologists to profitably run and operate iron ore mines and plants” (Kevin Thorne et al. 2007). At the laboratory scale, several types of techniques’ are currently used to perform sampling. This include: grapping, alternate spading, quartering, riffles divider and rotating divider etc.. Among all these instruments, rotary divider is the most commonly used. Nevertheless, the usage of a rotary divider is not a guaranty for samples representativity since the results have shown to be related to running speed of this instrument. For the present research work, the idea is to use iron ore concentrate to quantify the representativity of a rotary sample divider. In other words, the research idea is to determine the speed at which a rotary sample divider produces representative samples while treating iron ore concentrate from Carol Lake mine. The present report will give an overview of the methodology used and the principal results obtained."

Jan 1, 2016

Overview ?G-9 Discovery Hole 420 drilled May 2005 ?14.16% Zn, 1.76% Cu ?Greenfield discovery built into the G-9 Mine in under 4 years. ?Utilized a unique ?Parallel Track? approach to fast-track mine development. ?Raised over $200million in financing without a Feasibility Study. ?Mine built for $149.7 million, only 20% over PEA. ?Commercial Production declared April 1, 2009. ?G-9 Mine has now completed the first year of commercial production on April 1, 2010. ?Initial cash costs per pound of zinc US$0.39/lb -US$0.45/lb range. ?Mill operating at over1,900 tpd in March 2010, well above design capacity (1,500tpd) only one year after starting commercial production. ?Balance Sheet -$167 million assets, $24 million long-term debt, $22 million cash. ?Restarted Exploration ?excellent initial results. ?Strategically positioning Farallon to grow to a mid-tier mining company.

May 1, 2010

By L. Lui, A. Cauchon, A. R. Laplante

"The gravity circuit at Les Mines Camchib Inc. consists of two pinched sluices to bleed a feed to one of two 76 cm (30"") Knelson concentrator. The Knelson concentrate is upgraded to smeltable grade with a smaller Knelson (18/30 cm) and a riffleless table. Their tails are column cyanided and washed prior to recycle to the grinding circuit. This paper details size-by-size circuit performance. The Knelsons recover around 90% of free gold (as determined by Mozley Laboratory Separator), even below 37 µm. The sluices are ineffective, with upgrading ratios around 2, but approaching unity in the fine sizes. Much of the effectiveness of the circuit lies in the high gold circulating loads in the grinding circuit, which partly atone for the poor sluice performance, and the ability of the Knelsons to recover free gold. Secondary upgrading recovers slightly above 99% of the primary concentrate gold, 90% of it in a 65% Au concentrate and the balance in a heavily loaded (10 to 20 oz/st) pregnant solution. INTRODUCTIONBackgroundThe operating performance of the mill of Les Mines Camchib Inc. has been described earlier (Laplante et al., 1989). The presence of significant chalcopyrite (1 % and up) makes flotation necessary prior to cyanidation, to limit cyanide consumption and minimize environmental impact. In 1982, the presence of very high gold circulating loads in the grinding circuit lead to the commissioning of a gravity circuit, schematically shown in Figure 1. Gravity recovery of gold has been found beneficial because it increases metallurgical recovery by 1-3% (Laplante et al, 1987), as only part of the flotation tail is cyanided, and economic recovery, because of the lower net smelter return of gold in the flotation concentrate (as compared with the gravity concentrate). The latter increase is estimated, with a net smelter return of 95%, at 1.5% when gold recovery by gravity is equal to 30%. In early 1988, a sampling program was initiated to characterize the behaviour of gold in the grinding/gravity circuit. This paper reports on the results of this study."

Jan 1, 1990

By J. B. Boisvert, P. Oshust

A significant source of uncertainty in the diamond resource contained in kimberlite pipes is the volume of the pipes. Often the material within a pipe will be mined as ore, leaving the actual geometry of the pipe as a significant source of uncertainty. It is desirable to use stochastic techniques, rather than deterministic methods, to model pipe geometry because stochastic techniques generate multiple realizations that are reproducible and can be used to assess uncertainty in pipe geometry. The proposed methodology uses sequential Gaussian simulation of pierce point locations interpreted from drillholes through a kimberlite pipe. Kimberlite pipes are approximately cylindrical in shape; therefore, the data are transformed to cylindrical coordinates to facilitate the simulation of pipe geometry. Rather than using xyz coordinates to define the pierce points, z, ??and pipe radius are used. The radius variable can be simulated in z-??space to generate multiple realizations of pipe volume. Uncertainty in the volume of the pipe can then be evaluated. This methodology is demonstrated with a kimberlite pipe at BHP Billiton’s Ekati diamond mine.

Jan 1, 2008

By E. Roman, M. Brissette

"For its end of life, Kemess Mine processed its difficult-to-treat hypogene ore from the east pit, which is a lower grade copper and higher pyrite content gold ore. Metallurgical testwork showed that improvement was possible with finer grinding. In July 2010, small grinding media were introduced into the regrind mill resulting to a nearly 50% decrease of the power draw with a finer grind, an increase of 1.1% in the final copper grade, an increase of 1.2% in copper and 2.9% in gold recoveries at the cleaners. The overall recoveries of copper and gold increased by 0.6% and 1.3% respectively.INTRODUCTION Kemess Mine was located at 430 km North West of Prince George in North Central British Colombia. Its production started in May 1998 by Royal Oak Mines and was acquired by Northgate Exploration in 2000. Kemess reached its end of life production with its last of production on March 9th, 2011. The concentrator nominal capacity was 56,000 TPD consisting of a primary gyratory crusher feeding two identical conventional SAB circuits totalizing 35,840 kW available for grinding. Rougher flotation consists of four parallel rows of eight 130 m³ tank cells to produce a concentrate of 2% Cu and 6 gr/t Au which was pumped to a 5 m x 10.8 m regrind ball mill. The regrind installed power was 4,480 kW to generate a final grind of 80% passing 40 microns. This product fed the two stage cleaner flotation circuit, first stage being two parallel rows conventional 17 m³ Denver cells and second stage, two 3.3 m x 11.0 m flotation columns in series, designed and constructed by Kemess, to produce a 22% copper concentrate grade. The cleaner flotation middlings were returned back to the regrind mill (Froehling, Mohns, Roman & Grady, 2005; Froehling, Mohns, Rajwani & Fullam, 2007). The large copper-gold porphyry deposit was composed of 15% of oxidized supergene and leach cap ore and 85% of hypogene ore having three major alteration zones, mainly characterized by their sulphur/sulphide content. Chalcopyrite is the main copper mineral species with minor bornite. Gold was mainly present as free gold or electrum. The first alteration zone consisted of a phyllic alteration characterized by moderate and intense sericite alteration which had the highest mill throughput and twice the mine grade when in contact with the supergene horizon. The second zone consisted of a potassic alteration characterized by more competent groundmass and moderate to intense quartz stockwork which had a slightly lower mill throughput. Finally, a third alteration found beneath and on the east side of the deposit having almost no quartz stockwork and hardened groundmass, sulphide content is two to four times more. This zone had the lower mill throughput with significant drop in the mine average gold and copper grade. Through its mine life, the average life of mine copper head grade was 0.21% Cu and 0.64 gr/t Au. Head grades began to decrease from 2008 to be substantially lower in 2011 as shown in Table 1."

Jan 1, 2012

By Fathi Habashi

"Crushing and grinding of ores and their beneficiation by washing away gangue minerals has been practiced since ancient times. Primitive crushing was done by hand pounding the ore with a hard stone then by using metallic hammers. The mortar and pestle was mechanized using a lever and when the size of operations increased in the middle ages, the stamp mill was introduced. The grindstone played an important role in grinding of ores. Panning for gold and hand sorting of minerals were two old methods of separation, now gave way to modern techniques. Flotation started in the middle of the nineteenth century by using oils to collect the mineral particles and float them on the surface of the aqueous slurry. It was only in the 1920s when it was discovered that organic compounds were affective floating agents. Textbooks written by distinguished engineers such as Rittinger, Rickard, Pryor, Taggart, Richards, Gaudin, and others contributed to the recognition of this field as a new discipline to be taught in Universities. INTRODUCTIONThe ancient Egyptians knew already that it would be easier to melt an earth rich in gold particles than another which is poor. As a result all efforts were made to enrich the gold by washing away the light gangue minerals (Figure 1). Another ancient method for enriching gold particles from a river stream was by means of fleece, hence the Greek myth of the “golden fleece”. The present day Georgia was known in ancient times as Colchis and was a center for gold working. It was known to the ancient Greek as the land of Golden Fleece. The use of special cloth to catch gold particles was also described by Agricola in his 1555 book De Re Metallica (Figure 2)."

Jan 1, 2009

By A. Taylor, M. Blanchette, J. Doucet

"A Z1600 Jameson Cell Test Rig was rented for test work at Vale’s Clarabelle Mill operation. This paper discusses the evolution of renting the unit for test purposes to owning the unit and operating it as a revenue generating process component. The paper focuses on three aspects of the Z1600 project; the initial rental and installation, the test work performed in the cleaning circuit, and the business factors which led to the unit being permanently incorporated into the copper circuit.INTRODUCTION Clarabelle Mill is located in Sudbury Ontario (approximately 350 km north of Toronto) on the southwest rim of the Sudbury basin a meteoric impact crater that is 62 km long and 30 km wide. The result of the meteoric impact was concentrated nickel (Ni), copper (Cu) and platinum group metal (PGM) ore bodies in the outer perimeter of the basin; described in more detail by Hanley (1957). Vale currently has seven operating mines in the Sudbury basin, from which nine distinct ore types are mined. Ores are also received from two QuadraFNX mines. Clarabelle Mill processes all of these ores for the Ontario Operations of Vale. The mill, commissioned in 1971, was originally built as one of four mills operated by then Inco Limited. Between the late 70’s and the early 90’s process changes were made to consolidate the Sudbury Operations milling processes into a single operating mill, Clarabelle Mill. In 1990, the SAG mill was installed resulting in peak mill throughput of 11.9 million short tons per annum (Mstpa), with typical throughputs of ~10 Mstpa. Mill average feed grades were 1.4% Cu and 1.2% Ni. During the resources boom, plans were developed to increase the mill capacity at Clarabelle Mill in stages to a final capacity of 13.5 Mstpa. The project known as the Clarabelle Mill Expansion and Recovery Project (CMERP) included expansion and reconfiguration of the grinding and flotation circuits. The first stage was a planned increase in grinding capacity with the reallocation of existing mills, the existing flotation capacity would be required to treat higher throughput until the new flotation circuit was constructed."

Jan 1, 2012

By R. H. Seraphim

"Western Mines Limited produces gold, silver, copper, lead and zinc from a number of Paleozoic volcanogenic deposits near Buttle Lake on Vancouver Island. The deposits were emplaced along a series of submarine linear volcanic ridges that extended for at least 6,000 metres in a northwesterly direction.Rock types mapped include: andesitic, dacitic and rhyolitic flow s and volcanic breccias; detrital breccias, tuffs and hematitic silts; black and green cherts; and a variety of dykes and sills, including quartz porphyry and diorite. Orebodies are associated invariably, and in places intimately, with quartzsericite schist and rhyolitic rocks. The ore is complex, varying in mineralogy and tenor both within each deposit and from one deposit to another.Recent studies have increased our knowledge of the structure and left no doubt that the orebodies were deposited both within the throats of the linear vents and on paleoslopes adjacent to these vents.IntroductionWestern Mines Limited operates an 850-tonne-per-day mine, located 85 km south of Campbell River, B.C. The mine is at approximately 400 metres elevation, near the south end of Buttle Lake on Vancouver Island (Fig . I). It has operated since early 1967 and produced 3,650,000 tonnes with an average grade of 1.9 g (0.06 oz) gold, 93 g (3.0 oz) silver, 1.6 per cent copper, 1.0 per cent lead and 7.5 per cent zinc per tonne by the end of 1978. Current reserves are 1,157,000 tonnes of 2.7 g (0.09 oz) gold, 117 g (3 .8 oz) silver , 1.2 per cent copper, 1.2 per cent lead and 8.0 percent zinc per tonne (December 31, 1978).Ore from one zone, known as Myra High-Grade, is mined and milled separately because of its grade. Ore milled prior to December 31,1978, plus reserves, 180,715 tonnes of6.6 g (0.21 oz) gold, 554.5 g (17 .7 oz) silver, 0 .8 per cent copper, 3.2 per cent lead and 10.6 per cent zinc are included in the figures listed in the preceding paragraphs."

Jan 1, 1980

By R. Mohan Srivastava

"The goal of estimation is considered in the light of decision analysis. A simple example reveals the essential elements of decision-making in the face of uncertainty. A second example shows that these elements are also key features of many mining decisions. These two examples cause us to revive an old probabilistic notion that the goal of estimation should be to quantify what is unknown. The conditional probability distribution provides the complete statement of one's uncertainty. Once the conditional probability distribution has been established, one should retain as an estimate the value which minimizes some objective loss function. A third example shows how the ""best"" estimate depends on the chosen loss function. Current practice is almost exclusively based on the least squares method, which assumes a loss function which penalizes underestimation and overestimation equally. This is unfortunate not only because symmetry is an unrealistic assumption but also because mining offers a rare opportunity to state the loss function directly in terms of profitability. Both the theoretical framework and the practical tools exist to allow us to reconsider the conventional notion of the ""best"" estimate. IntroductionThis paper looks at estimation in the mining industry from the point-of-view of decision analysis. Virtually all decisions depend on estimates since few of the important parameters are ever known exactly. In this paper we will be referring mainly to the estimation of ore grades, though the approach discussed here is generally applicable to any decision in which relevant information is uncertain.In the first section we look at a very simple example of decision-making in the face of uncertainty. We will then tum to a mining example and see that the essential features of the simple example still pertain. From these two examples it will be clear that the decision analysis approach rests on two key concepts: the conditional probability distribution and the loss function. A third example demonstrates how different loss functions produce different ""best"" estimates from the same conditional probability distribution. In the final sections we willexamine the current practice of estimation in the mining industry. Though the tools for estimating the conditional probability distribution already exist, a change in the way we think about ""best"" estimates is needed. Very little attention is presently paid to the loss function even though it is readily available in many mining applications."

Jan 1, 1987

By Hamid Butt

Information Technology ??Advanced Information Technology is dramatically changing information flow within organizations. This enables employees to have information at their fingertips to make informed and prompt decisions. ??Real-time information allows timely analysis, which dramatically reduces cycle times, making organizations faster and more flexible. Business Challenges ??Continual growth of mining and Mine mobile fleet.??Increasing maintenance costs. ??Difficult to identify and troubleshoot equipment problems while equipment is operating. ??New equipment is increasing in complexity and cost. Therefore, each failure results in a greater impact to production and cost. ??Troubleshooting practice is reactive. ??Protect and optimize the use of mining assets to realize maximum business value. ??Maintenance and Operating information is not easily accessible ?no near real-time system that provides complete information.

May 1, 2006

By U. Dillon, G. Blackwell

"Geographic information systems (GIS) provide an efficient means for the recording, manipulation, revision, display and analysis of spatially referenced data. GIS are widely used at the exploration stage of mine development, and are increasingly used for reclamation planning. The ability of a GIS to perform spatial searches and query spatially referenced data make it a powerful tool for use at all stages of mine development. As the amount of data available for analysis increases, so does the power and flexibility of GIS as a planning tool.Starting from the exploration database, this paper describes how a GIS can be used for the development of mining plans based on topography, geology and mineralization information stored in a relational database. Planning decisions approaching the optimal can then be made for a wide range of parameters, including stockpile and waste dump locations, the location of potentially acid generating and neutralizing material for dump design, profitable and risk-controlled mine extraction sequencing, and haul road locations. This is made possible by the overlay and buffer analysis capabilities of a GIS which are explored and exploited to produce a continuous mine production planning program, as well as site remediation and reclamation using a successful case study. IntroductionGeographic information systems (GIS) are a relatively new tool in the mining industry. Although they have existed for a number of years, the potential of GIS for mine management and planning is only beginning to be investigated and exploited. The unique spatial capabilities of GIS make them particularly wellsuited for use in mining, where spatial information is fundamental to the processes of mineral exploration, mine development, and environmental reclamation. A number of potential applications for GIS in the mining industry have been identified, and they are widely used for exploration and reclamation. The use of a GIS as a platform for the development of mine planning routines and software remains an interesting, but as of yet unexplored, application of this technology."

Jan 1, 2003

By J. R. Gordon

I-Introduction The possibility of adapting low-temperature reduction methods to the treatment of iron ores has been suggested on numerous occasions. Papers published on the subject include, notably, Bulletin 270 of the United States Bureau of Mines on The Production of Sponge Iron, the Symposium of the American Electrochemical Society (1927) on The Gaseous Reduction of Ores and Other Metallic Compounds, and Les Procédés Actuels de Traitement Direct du Minerai de Fer, by A. Mayer (Revue de l'Industrie Minerale, Nov. 15th, 1932) (1). The present paper contains the results of an investigation of the reducibility of some Ontario ores. The concentration of these ores and of the products of reduction has also been investigated.

Jan 1, 1933

By Casey Erickson

Goldstrike Property ??Located in Elko, NV USA?Carlin Trend ??Mining Since 1985 ??27 Million Ounces of Gold Mined ??Production of 400,000 tons/day ??1,600 Employees

May 1, 2011

By Fabien Miller

Automation technologies are increasingly envisaged to improve underground mining productivity. However, the technologies need to be used and adopted gradually in order to get the best benefits. This paper presents the technical and operational aspects of autoguided production vehicles at Brunswick Mine. During 2001 Noranda?s Brunswick Mine has successfully commissioned an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two orepasses. Operational advantages include increased system capacity and enhanced safety and comfort for the operator. The data obtained up to now indicate that the system can operate reliably in mine production

May 1, 2002

By B. Stimpson, K. Kosar, K. Barron

"A number of high wall failures have occurred in some of the Alberta coal strip mines of a type called by the authors ""Multiple block plane shear slope failure "". They cause rapid deterioration of the dragline bench, reduced productivity and maintenance costs.The failures are invariably associated with the presence of almost horizontal (± 5 degrees) bentonitic clay bands in the overburden, often immediately above the coal seam, and regress behind the slope as a series of tension cracks which isolate detached blocks. As many as 17 sets of cracks have been observed, at lateral distances in excess of five times the slope height from the toe.The theory of this mode of failure is presented and a limiting equilibrium computer program which will produce deterministic or probabilistic (Monte Carlo) solutions is briefly described. A case history of one such failure is documented. It is shown that the extent of the regressive failure is exceedingly sensitive to the water table elevation, leading to the conclusion that drainage, if practical, represents the best control strategy. IntroductionA number of high wall slope failures are occurring in some of the coal strip mines in Alberta of a type called by the authors ""Multiple block plane shear slope failure""(I). These failures cause a rapid deterioration of the bench from which the dragline operates, reduced productivity, and necessitate conregresses into the slope as a series of tension cracks and detached blocks. As many as 17 prominent cracks or crack zones have been observed, the last being in excess of five times the slope height distant from the toe.The block between each pair of cracks must be at limiting equilibrium, i.e. the factor of safety equals one. This condition can be used to determine the locations of the cracks which develop in sequence behind the face."

Jan 1, 1986

By V. Dinesen

"Grinding is simply the function of reducing particles in size or creating new surface areas. This may be accomplished by many means but we will only concern ourselves with the continuous grinding process as performed in a revolving drum or mill, containing a grinding media. Such a mill consists essentially of a feed head, a cylindrical shell section and a discharge head. To prevent internal wear of these parts it is customary to attach replaceable linings over the wear areas. The specification and design of these mill liners is more important than generally conceded. As they reduce the effective internal volume of the mill, they will consequently affect the whole mill ·design and operation.A number of mill designs of various sizes are available for combined crushing and grinding of materials within a wide size range. For simplif1cahon purposes we will refer 1n particular to conditions relating to standard mill shapes having a length which is greater than the diameter. Such mills usually rotate at speeds between 60% to 85% of the critical speed and may, depending on the grinding media used, be classified as rod mills, ball mills and pebble mills.LINER MATERIALSA great variety of materials have been and are being used for mill linings. These include wood, ceramics and cements, rubber and plastic compounds, rolled and forged steels, cast steels and cast irons, both plain, alloyed and specially treated.The choice of a liner material depends on many factors. In both dry and \\.:et grinding, it may be necessary to consider product purity, colour, chemical reaction etc. but for our purpose we \viii refer to wet grinding operations as generally used within the mining industry."

Jan 1, 1972

By M. C. Bétournay

Hydrogen fuel cells are a known technology, having been applied to stationary (e.g. equipment, buildings, and power plants) and vehicle applications (e.g. transit buses and space shuttles). There is currently a growing need to provide alternate power systems to diesel fuel for underground mining vehicles to improve underground air quality and reduce production costs and greenhouse gas emissions. To date, however, fuel cells have not been exposed to underground mine air and physical conditions. A testing program was carried out to provide information on the vulnerabilities of fuel cells as part of a number of proof-of-concept projects to apply hydrogen power to underground mining vehicles. The fuel cell type of choice for the industry, the proton exchange membrane, would function at the range of surface operations, and use hydrogen that is stored under low pressure and risk. A small fuel cell stack was tested in a cooperative project between CANMET, the Fuelcell Propulsion Institute, Inco, the Ontario Ministry of Labour, Sandia National laboratories, and H-Power. This article will review the tests carried out to measure the effects from high humidity, mineral dust, diesel emission gasses and diesel particulate matter, as well as from shock and vibration provided to the unit in underground conditions at Inco?s 175 Orebody minesite and Stobie mine. The test results provided will show that the unit was not affected by the underground conditions; physically and electrically, the unit performed without any reduction in operation or adverse effects imposed

May 1, 2005