Search Documents

By D. Saramak, Z. Naziemiec

"Chalcedonite is an unique rock due to the relatively small area of its occurrence. It also possesses multi-raw-material features therefore it should be given a special protection aiming at its complete and optimal utilization. It is the natural sedimentary rock and the only mine in Poland, located in Inowlodz, where the opencast mining from “Teofilow” deposit is carried out.Chalcedonite mainly consists of cryptocrystalline and microcrystalline chalcedony together with small amounts of autogenous and detrital quartz. The chalcedony itself is a fairy common mineral and many forms of its occurrence is known, some of them are semi-precious minerals. Among the most popular ones following can be found: agate, bloodstone, onyx, carnelian, chrysoprase. Many countries own chalcedony deposits: Australia, Brazil, India, Canada, Namibia Russia, South Africa. However chalcedony in its pure form does not occur in the mentioned chalcedonite rock. The pores, which take usually from 5% to 25% of volume and have sizes smaller than 0.5 mm, are the characteristic feature of all chalcedonite forms. The paper presents some crucial problems of its processing together with most significant directions of its applications. New method of chalcedonite enrichment based on densimetric separation (patented in Poland) is presented. Results of investigation show that the obtained products can increase quality of concrete and filter grits."

Jan 1, 2016

By K. Chomyn, R. Veenstra, P. Zangeneh, Hatch Ltd., C. Van der Woude, H. Ghorbani

"The furnace is the heart of smelting operations, and therefore the performance, reliability, and campaign life of the furnace are critical considerations. Furnace refractory is exposed to high temperatures and other harsh operating conditions causing brick erosion, crushing, and cracking, typically limiting the furnace campaign life and requiring costly furnace shut-downs for refractory re-lining. Despite extensive study, the in-service thermal / mechanical stresses in these complex refractory systems are not generally well understood. Hatch has developed a thermal-mechanical finite element analysis (FEA) based furnace refractory modeling approach that allows for the quantification of refractory movements, load distribution, and thermal / mechanical stresses.Due to the complexity of the refractory system, a range of models are used to identify and assess damage mechanisms and design improvements, including: 2D models, to capture expansion and movement of individual bricks, changes to load paths, and thermal stresses; and 3D models, to include the effect of differential expansion between bricks in each course, and assess overall load distributions. The 2D and 3D analyses include the effect of nonlinear temperature-dependent properties, thermal expansion, movement of individual bricks with frictional contacts (i.e., gaps can open, bricks can slide), and brick tensile or compressive failure. Both as-built and damaged conditions can be investigated (e.g., after bath zone brick erosion), for circular and rectangular furnaces. 3D models also include papering and brick joint & interface action.Analyses using these models have shown the importance of thermal stresses, papering, and geometry / arrangement of individual bricks. Results have been used to identify and assess damage mechanisms, showing good alignment with furnace autopsy observations. By using this FEA-based approach to quantify the refractory design, the risk of damage can be significantly reduced, low-cost design changes can be identified, and the furnace campaign life can be extended.INTRODUCTIONThe furnace is the heart of smelting operations and therefore the performance, reliability, and campaign life of the furnace are critical to the success of the smelting operation. Furnaces are inherently exposed to high temperatures, often in excess of 1600°C (Holappa, 2004), and furnace operating power has progressively increased over time (Voermann, Gerritsen, Candy, Stober, & Matyas, 2004). The refractory system must withstand high temperature, high heat flux, and other harsh operating conditions. These conditions are particularly significant for the furnace hearth, and can lead to damage including brick erosion due to molten material flows, crushing due to thermal expansion loads, and cracking due to severe thermal gradients within the bricks. Refractory damage typically limits the furnace campaign life, requiring costly furnace shut-downs for refractory re-lining (repair or replacement). In some cases the refractory may lose integrity causing damage to nearby equipment and harm to personnel."

Jan 1, 2016

By T. Abu Leil

A new class of ternary Mg-Sn-Ca alloys is being developed to address the dual demands of corrosion and creep resistance at service temperatures. While tin has proven to enhance the corrosion resistance, calcium is expected to significantly increase their creep resistance of binary magnesium alloys. Their effects in ternary magnesium alloys are not yet known. The series of alloys studied has Sn and Ca in the ranges 3-6% and 1¬2%, respectively. The results indicate that these alloys have two-phase structures with CaMgSn phase dispersed in a matrix that is predominantly a solid solution of magnesium. The corrosion behavior of these alloys has been investigated by means of salt spray tests and potentio-dynamic measurements. Creep behavior of these alloys was measured at a temperature of 135 C under an applied compressive stress of 85 MPa. Scanning Electron Microscopy with Energy Dispersive X-ray facility and X-ray Diffraction techniques were used to characterize the microstructures. The results indicate the prospect of designing alloys that can provide optimum combinations of corrosion and creep resistance by adjusting the relative compositions of Sn and Ca in the system.

Jan 1, 2006

By L. Bichler

Utilizing thermal analysis techniques, pioneering research into the solidification mechanism of a popular magnesium alloy AZ91E cast by the Lost Foam Casting (LFC) process was carried out, Foam characteristics, section thickness and application of vacuum were seen to have profound effect on the cooling rate, thermal gradients and casting temperature profiles.

Jan 1, 2005

By P. M. Pearson

This paper describes the principles ()f systems engineering and their application to the various transport problems confronting the mining industry. The organization of mining operations into sub-system design problems is explained.

Jan 1, 1970

By I. M. Masters

Iron removal and control in processes employing pressure leaching technologies developed at Dynatec Corporation are reviewed. Discussions are focused on recent developments in the processing of nickel-copper matte and copper concentrates, and on the Ambatovy laterite project in Madagascar. Iron control and its implications on flowsheet design in the pressure acid leaching (PAL) treatment of laterite ores and in the oxidative pressure leaching of mixed nickel-cobalt sulphide intermediates are also discussed.

Jan 1, 2006

By G. Szilvay, P. Kinnunen, J. Salminen, V. Miettinen, O. Salmi, J. Mäkinen

This paper demonstrates experimental studies on bioprocessing of different waste streams. In Part I of this paper three tailings from mining industry were bioleached with mixed acidophilic culture in order to solubilize valuable metals, like copper, nickel, zinc and manganese to leaching liquor. Bioleaching resulted in > 70 %, > 85 %, 100 % and > 70 % leaching yields for Cu, Ni, Zn and Mn, respectively. However, contaminants like arsenic and chromium were not leached efficiently and they will cause challenges in residual solids and sometimes also in metal recovery from leaching liquor. Bioleaching resulted in 99 % leaching yield for copper. Part II demonstrates mine water treatment and also gold recovery from process liquids with biosorption method. The novelty of biosorption was finding that certain fungal species were able to be cultivated to self-immobilized systems, which are easier to operate than traditional suspended biomass methods. Biosorption resulted in more than 90 % removal for all contaminants, but was also seen to be gold selective.

Jan 1, 2014

By C. Robinson

The Diavik Diamond Mine is located in one of the most remote and forbidding places in the world, 220 kilometres south of the Arctic Circle and on the bed of a vast northern lake, Lac de Gras. A single road, built out of ice and crossing frozen lakes, connects the mine with other operations and Yellowknife, the capital of the Canada's Northwest Territories. Diamonds were first discovered in the Lac de Gras region in the early 1990s, and construction of the Diavik Diamond Mine was completed in 2003. Diavik currently mines three kimberlite pipes. Open pit mining has now concluded and all three pipes are mined using underground mining methods. In early 2010, Diavik began mining and processing initial ore from its new underground mine; underground mining operations are expected to continue beyond 2020. The initial mine ventilation system was an exhausting (pull) system with fresh air supplied by a fresh air raise and a main ramp. Return air was exhausted via two raises and a secondary ramp. The system had a total flow capacity approximating 401-411 m3/s. With planned increased production and with changes in mining method, it has been proposed to change the mine ventilation system to a positive (forcing) ventilation system in order to meet projected increases in flow requirements of 566-708 m3/s. Extensive engineering work was developed in order to successfully achieve the changes in system configuration. In the proposed configuration, the main ramp is in an exhaust configuration and exhaust raises are converted to fresh air raise. A number of system implementation options were investigated and phased plans for system execution have been developed. The proposed changes to the ventilation system are substantial and involve extensive construction work. Work was commenced in 2011, each planned phase has been successfully completed to date, and system changes continue today in order to achieve complete system flow reversal and increased flow distribution. This paper details the design of the modified ventilation system and commissioning work which will allow the mine to meet its future production targets.

Aug 1, 2013

By Claudio Rocha Rosales

"Peñoles is a mining group with integrated operations for the smelting and refining of non-ferrous metals, and it is also a chemicals producer. Peñoles is the world’s foremost producer of refined silver, metallic bismuth and sodium sulphate. It is also the leading Latin American producer of refined gold, lead and zinc. The Met-Mex Peñoles Zinc Plant commenced operations in 1973 with an annual production capacity of 105,000 t/y zinc. Since then, production capacity has increased, and at present, it stands at 240,000 t/y zinc. In this paper, the leaching process and particularly the operation of the jarosite circuit is reviewed, specifying process improvements to treat high iron calcines.INTRODUCTIONTwenty years ago the Electrolytic Zinc Plant in Peñoles was treating high quality zinc concentrates with low concentrations of iron (~7.5 wt.%) and silica (1.8 wt.%). Nowadays the quality of zinc concentrates is poor with a typical iron content of around 11 wt.% and silica at 2.0 wt.%. This has created numerous processing problems in our roast-leach-purification- electrolysis sections. In order to meet customer requirements it is necessary to find processing solutions to assure the operational continuity of the plant. These processing solutions are the focal point of this paper.REVIEW OF THE LEACHING PROCESSThe purpose of the leaching process is to recover the metals, mainly zinc, through a series of extraction stages with sulphuric acid solutions, which progressively increases the zinc dissolution. After the series of acidification stages, the solution, which is rich in iron, is sent to the jarosite circuit to separate zinc from iron (Garcia & Valdez, 1996). The first step of the leaching process is the neutral leach circuit which produces a zinc sulphate solution that is sent to the purification section for the removal of impurities such as cadmium, cobalt and copper. Then this solution is sent to the tank house to feed the electrolytic cells."

Jan 1, 2016

By D. Larouche, M. Mardan

Hot tearing is a complex defect in aluminium castings which is produced during solidification when a certain amount of liquid phase remains and weakens tensile resistance of the alloy. In direct chill casting of aluminium alloys, hot tears initiate at the surface of sheet ingots just after the primary cooling zone, where the microstructure is particularly vulnerable. In order to study the hot tearing susceptibility of these alloys, and the effect of grain refiners on their thermo-mechanical behavior , tensile tests were carried out in the semi-solid state ( ~95% solid) and at low strain rates using an apparatus called DCSS, for Direct Chill Surface Simulator. This apparatus, originally developed at Alcan Arvida R&D Centre (ARDC), is an instrumented rig test reproducing the conditions prevailing during the primary cooling stage of the DC casting process. The mechanical behavior of solidifying shells and the hot tear formation under applied tensile loads were measured and the occurrence of hot tearing was observed. Temperature in different locations of the casting, applied load and surface strain were monitored during the tensile tests conducted on aluminum alloys AA5182, AA6111 and AA3104. The microstructure of the tested samples was examined using the optical microscope to evaluate their columnar or equiaxed aspect and their effect on the mechanical response of the alloy. A special emphasis has been given to the evaluation of fractions solid existing in the castings at the start of the tensile tests, taking into account the local temperature, thermal gradient and cooling rates experienced. It was found that excessive grain refiner additions decreased the strength of solidifying shells because of the increased level of porosity induced by easier nucleation of new phases (gas included). It was also observed that cooling rates increased with the level of grain refiner, a phenomenon that was associated to the higher number of contact points obtained with small equiaxed grains. Finally, the concept of a stress based criterion for hot tearing was reinforced by the strengths obtained on not grain refined AA5182 and AA6111 showing similar fraction solid near the surface, but significantly different grain sizes.

Jan 1, 2006

By E. Hinton, L. Bloomquist

"This paper describes a guidance system for autonomous underground mining vehicles, which does not require any infrastructure or inertial positioning systems to aid the guidance process.BackgroundINCO Limited mines approximately ten million tons per annum through 12 operating mines in the Sudbury, Ontario, area (Fig. 1). With challenges from operating in a cyclical marketplace as well as new technologies making alternative nickel ores more competitive to refine, the Mines Research department embarked on a strategy that pointed toward automation as a tool to help the company become even more economical in mining.The mining industry has been looking for ways and means to mine orebodies more and more inexpensively. Automation and the lessons learned from manufacturing had a great influence in the direction of research at INCO Limited over the past ten years. Guidance systems have evolved over the years but the majority of commercially available systems rely on some form of infrastructure. This, in part, has caused some resistance from operators to install and maintain automated or semi-automated systems for guidance of underground machinery.Internal industrial studies cited travel time to and from the workplace as one of the major time sinks in the shift of underground miners. Depending on the mine, it may be as much as two hours moving in and out of an area. Some work areas have accommodated this by having “hot changes” at the work place. However, at some point in time, there are two people tasked with the same job and on site at the same time to make this overlap occur.Tele-operation of underground hard rock equipment eliminated this overlap and also provided a comfortable environment in which to work. By taking advantage of the communications network installed, the miners proved that they could operate three machines with relative ease. This was accomplished by a vision-based, “painted line,” autonomous guidance system termed the light rope system.With a few years’ experience with the system, some issues have arisen, including the cost of the rope itself (Fig. 2).The vehicle’s route is limited to the paths defined by the light rope, and a system of switching power to the light rope to select different routes is required. The rope itself is subject to damage from nearby blasts. Also, the system offers no obstacle detection; the vehicle may be switched off as a means of shutting the machine down thus protecting personnel in the area."

Jan 1, 2001

By Melanie Grob

Two commonly estimated fractal dimensions, called b and D values, represent statistical characteristics in the distribution of magnitude sizes (b) and spatial hypocenter locations (D) of microseismic events, respectively. We postulate that the values of b and D are related to specific stress regimes. Through different case studies of fluid injection into an oil/gas reservoir or geothermal field, we infer that the measured temporal variation in fractal dimension b is most likely due to significant changes in the local stress regime. The fracture dimension D indicates the spatial clustering of events. The distribution of these events can vary with time because of stress perturbations that (re)activate fractures whose direction favours their movement under a specific stress regime. Thus a combined statistical study of these two dimensions can help infer the variations of local stresses in a reservoir.

Jun 1, 2012

By Brooke Clements

The Buffalo Head Hills region is located approximately 350 kilometres northwest of the city of Edmonton in northcentral Alberta (Figure 1). The Alberta diamond joint venture consisting of Ashton Mining of Canada Inc., Alberta Energy Company Ltd and Pure Gold Minerals Inc. began exploring for kimberlites in the Buffalo Head Hills region in late 1996. At the time, the Mountain Lake diatreme, located 200 kilometres to the southwest, was the only reported kimberlitic rock in Alberta (Leckie et al., 1997, Figure 1). Exploration efforts since 1996 have successfully identified a new diamondiferous kimberlite province in Canada.

May 1, 2001

By R. De Ruiter

"In times when mines are emphasizing cost reductions, a properly rebuilt shall conveyance can be more cost-effective than building a new unit. Awareness of the safety aspects of conveyance design along with proper maintenance playa large part in reducing operating costs. A knowledgeable operator can maintain a high level of safety and significantly lengthen the service life of a conveyance. Such an operator is also in a better position to determine when a major overhaul is necessary.After the decision has been made to rebuild, operators must decide who will do the overhaul. Whether the work is to be done in-house or contracted out, the goal is to achieve a conveyance recertified to ""as new"" condition. By dealing with conveyance rebuilds as an engineered product, operators can be certain they are getting a top quality product for their money.This paper deals with the engineering aspects of conveyance rebuilds. Actual examples of typical problems are discussed and corrective action outlined. Design considerations such as proper material selection, component fatigue due to cyclic loading, effects of stress concentrations and corrosion are all part of the initial design considerations that must carryover into the rebuild process. All too often equipment overhauls are done by people who are not experienced in conveyance design.As a manufacturer of mining equipment, Wabi has gained expertise over the past 70 years. By sharing this knowledge the company hopes to create a safer work environment and help to reduce operating costs."

Jan 1, 1994

By Yan Jie

The oxygen-enriched bottom-blowing continuous converting process for copper matte was recently developed by the China-ENFI Engineering Corporation. The first commercial plant based on this technology was successfully commissioned at the Yuguang smelter in China in March 2014. The present paper describes this new continuous converting process and compares technical characteristics with other continuous converting processes including: Kennecott-Outokumpu flash converting, the Mitsubishi Process, the Noranda Converter and TSL continuous converting. The bottom-blowing oxygenated continuous converter with competitive capex and opex costs is seen as an attractive alternative to the Peirce-Smith converter.

Jan 1, 2014

By J. B. Mawdsley

"The Red Lake Gold Shore mine is 4/5 mile west of the town of Red Lake, Ontario, and a mile northwest of the Howey mine. It came into production in August 1936, and in a little over 2 years produced 21,099.58 oz. gold from 83,949 tons milled.An investigation of this deposit was made by the writer during parts of September and October, 1937t. The geology of the deposit is also discussed by H. C. Horwood(2) , and the characteristics of the ore were investigated by the Bureau of Mines, Ottawa (1).The orebodies are pipe like and close together, in a north-northwesterly trending zone of dykes, veins, and shear zones in a granodiorite stock, just south of a pronounced valley with a trend of N.65°E. believed to lie along a strong shear zone and fault . The dykes, veins, and mineralization are believed to have been successively emplaced along structures having three general trends and that were due to compressive stresses that alternated, at least four times, from west of north to east of north. In common with many other gold deposits, the gold mineralization here occurred late and followed the last east-of-north stresses.WALL-ROCKSThe mine is within the Dome stock, % mile from its southeast margin. Near the mine the rock is a pink hornblende-biotite granodiorite, grading within short distances, but not abruptly, into a dark grey variety. Near the workings at least, scattered small inclusions form about ½ to 5 per cent of this body. Most of them are fine-grained, angular, or partly rounded, greenstone fragments, but some have been partly granitized and feldspar has been developed in them."

Jan 1, 1954

By Curtiss O. Ehrsam, M. Naseem Mian

Alaska’s Red Dog Mine is strengthening its position within Cominco’s “Vision 2000”strategic plan by continually improving quality and quantity of production while reducing costs. Red Dog has evolved into a stable and mature operation, after six years of milling experience. A high grade, partially oxidized orebody in the severe Arctic environment, along with competing producers in a volatile metals market, are the continuing challenges facing Red Dog. The Red Dog Mine is striving to meet these challenges with emphasis on operator training combined with creative systems development and increased production. This paper describes developments in operations along with future plans.

Jan 1, 1996

By T Nakamura, M. Itoh

Most of the used cathode ray tube (CRT) glass in Japan, which contains lead oxide, was exported and recycled in overseas factories of new CRTs. However, domestic treatment and recycling of waste CRT glass has become necessary because overseas CRT factories have shut down and exports of CRT glass have stopped. Some of the waste CRT glass recycled domestically is charged in lead blast furnaces instead of silica flux, because there is no local reproduction route for glass that contains lead. However, the mass of CRT glass that can be treated in this manner is limited because of its high silica content. Consequently, additional treatment methods for waste CRT glass are required so that more can be used as a lead smelting material. In this study, waste CRT glass was treated with hydrofluoric acid to dissolve the silica contained in the glass, and the dissolved lead was recovered by precipitation. Lead metal was recovered by electrodeposition from the prepared hexafluorosilicic acid solution.

Jan 1, 2011

Fault detection and identification are major challenges in process engineering and manufacturing and the key component of abnormal event management systems. Timely detection, diagnosis and rectification of abnormal or faulty process conditions can lead to savings of billions of dollars in equipment damage and lost productivity, not to mention the prevention of injury and loss of human life associated with industrial accidents. A major contributing factor to current losses in industry is the reliance on human operators to interpret high-frequency samples from hundreds or thousands of variables simultaneously. As a result, the automation of fault detection and diagnosis is seen as crucial to the successful implementation of abnormal event management, the need for which is becoming all the more urgent given the increased complexity associated with modem industrial plants. In this paper, a methodology for process monitoring that uses support vector methods to extract nonlinear features from data is discussed and applied in the diagnostic monitoring of an industrial liquid-liquid extraction column.

Jan 1, 2005

By H. S. Bostock

"The study of the geology of Mayo district began in 1900 with R. G. McConnell's exploration of Stewart river; and has been carried on intermittently for the Geological Survey of Canada by J. Keele; D. D. Cairnes; W. E. Cockfield; C. H. Stockwell; and the writer. It has revealed a thick group of schists; quartzites; and crystalline limestones; almost certainly Precambrian in age; placed in the Yukon group; and a group of younger intrusive igneous rocks varying in composition from granite to gabbro. These include bodies of many sizes and forms; from stocks 8 miles across to small dykes and sills.Prospecting in the district began about 1897 and has disclosed the presence of gold, silver, lead, tungsten, tin, zinc, antimony, copper, arsenic, manganese, and mercury, both in placer and lode deposits . Of these metals gold, silver, and tungsten have been produced from placer deposits, and silver, lead, and gold from lodes. This paper deals only with some structural relationships of the lode deposits, generally referred to as the silver-lead veins, which have yielded the greater part of the mineral production of the area. From 1938 to 1941 the geological mapping of the district for publication on a scale of 4 miles to 1 inch was carried out by the writer, and the ideas expressed here are based on this work. No comprehensive detailed study of the silver-lead veins has been made, but the mapping has brought to light several important facts. The rocks of the Yukon group, although of a striking sameness throughout their section, can be divided into a number of distinguishable members by means of which the main structures can be traced . The most important and readily distinguishable rock in the group is referred to here as the quartzite member. This is composed of quartzite and schist in about equal proportions. The quartzite is resistant to erosion and forms most of the outcrops of the'member and the peaks of the Gustavus mountains and mount Haldane (Lookout)."

Jan 1, 1954