Search Documents

By T. H. Wilson

In 1901, the Crow's Nest Pass Coal Company, Limited, began producing industrial coke in 212 beehive ovens at Michel colliery. By 1908, 486 ovens had been installed and in that year 147,623 tons of coke were produced. Coke manufacture has been continuous from 1901 until the present time (1946), with total production of 2,795,402 tons. At present writing, only 100 beehive ovens are operating and production is reduced to 1,800 tons per month, due to the shortage of suitable labour. These ovens are drawn by hand, on contract, and the workmen are exposed to considerable heat. A man draws three ovens in eight hours, thereby producing approximately 1072 tons of coke per day. In addition to the inefficient and costly method of drawing coke in beehive ovens, tremendous losses are experienced in the wastage of gas and tar, which are driven off into the atmosphere. Also, the yield of coke per ton of coal fed to the ovens is low as part 9f the carbon is utilized in producing heat to carbonize the remainder of the coal. A recovery of only 55 per cent of the carbon, as coke, is obtained. The coking process takes place from the top of the charge, which is 21/2 feet deep, downward to the floor. Six and a half tons of coal are charged and 3.6 tons of coke are drawn from the oven after 72 hours' carbonization. The beehive ovens using Michel coal produce a very hard and tough coke, large in size and of silvery appearance, which has served the requirements of both foundry and smelter for many years. In 1938, the Company made a careful study of coking processes with a view to introducing a more economical method than beehive ovens and one that would be less dependent on skilled labour, the supply of which was rapidly diminishing at that time. Various methods of by-product coking were investigated, and it was decided that the Curran-Knowles process offered the greatest possibilities because of the low capital investment in relation to output and also because the horizontal oven design was suitable for an expanding coal. Consequently, a test on Michel B seam coal, supervised by Mr. E. Burrough, of the Fuel Research Department, Ottawa, was run in the Curran-Knowles plant at West Frankfurt, III. The results of this test led to the construction of a ten-oven battery of 32 ft. 6 in. by 8 ft. 3 in. Curran-Knowles ovens at Michel, which were completed in November, 1939. This battery was built as an experimental unit, with provision for an additional ten ovens if the coke proved satisfactory for the market. In 1942, an expanding coke market led to the construction of a second battery of ten ovens, which were completed in April, 1943.

Jan 1, 1947

"These standards were developed by the CIM for use with the value or worth of a Mineral Property as opposed to “evaluation” where the key objective is an economic assessment or determination of the economic merit of a propertyP1 .0 BACKGROUNDPl.1 There are at present no comprehensive standards for valuation of Mineral Properties in the Canadian mining industry. The Mining Standards Task Force (MSTF) of the Toronto Stock Exchange and the Ontario Securities Commission in its Final Report (January 1999) specifically recommended that the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) form a committee of valuation practitioners to review and advise on approaches to valuation of Mineral Properties.Pl.2 On May 5, 1999 at the Calgary Annual General Meeting, CIM Council approved the formation of a Special Committee on Valuation of Mineral Properties (CIMV al) to be co-chaired by Keith Spence (Chairman of the CIM Mineral Economics Society) and Dr. William Roscoe (Roscoe Postle Associates Inc.).Pl.3 The mandate of CIMVal is to recommend Standards and Guidelines for Valuation of Mineral Properties to be used by the mining industry in general and to be adopted by Canadian securities regulators and Canadian stock exchanges.Pl.4 The members of CIMVal represent of a mix of professional disciplines and experience in the field of Mineral Property valuation:Keith N. Spence (Co-chair), Alliance Pacific Resources Inc., TorontoWilliam E. Roscoe (Co-chair), Roscoe Postle Associates Inc., TorontoMichael J. Bourassa (Secretary), Aird & Berlis LLP, TorontoChristopher R. Lattanzi, Micon International Limited, TorontoRoss D. Lawrence, Watts, Griffis and McOuat Limited, TorontoPaul E. Lunney, Noranda Inc., TorontoCraig A. Roberts, Pacific International Securities, VancouverDavid A. Scott, CIBC World Markets, TorontoIan S. Thompson, Derry, Michener, Booth & Wahl Consultants Ltd., VancouverWilloughby A. Trythall, retired Placer Dome executive and consultant, Vancouver"

Jan 1, 2003

By C. S. Touchard, F. Bourgeois, L. Cassayre, Julcour-Lebigue C.

Developing a hydrometallurgical process that can overcome the refractory nature of chalcopyrite (CuFeS2) to leaching still eludes the minerals industry, despite major research efforts spanning decades. The several leaching experiments of this ore in sulfuric acid tend toward the same conclusion that the precipitation of elemental sulfur or iron containing species are the main dissolution inhibitors. Describing both the electrolyte composition and the various solid phases in equilibrium for the Fe-H2SO4-H2O system is essential to overcome this issue and to find an operating window. According to the thermodynamic models and to the thermodynamic data, we demonstrate, in this study, the need to use the Specific ion Interactive Theory (SIT) model to describe complex electrolytic systems through a limited number of parameters. Hence, the binary interactions for our case study have to be defined and estimated. This work develops a methodology to determine these parameters of the SIT model up to 90°C and an acid concentration of 1 mol/kg from published data for H2SO4-H2O and Fe(II)-H2SO4-H2O sub-systems or from new experimental data for the Fe(III)-H2SO4-H2O one. This method will eventually be applied to copper systems to lead to a thermodynamic description of the complete CuFeS2-H2SO4-H2O system. INTRODUCTION A leaching process consists in the dissolution of a solid phase into an aqueous medium in order to extract compounds of interest. It is a key step in the hydrometallurgical processes used in the primary production and recycling of metal components. One of the main leaching issues is the formation of passivating layers on the surface of solid particles, whose consequence is a partial or total hindrance of the dissolution. The leaching of chalcopyrite (CuFeS2) in sulfuric acid is a prime example. No industrial solution for the atmospheric pressure leaching of this ore has been developed to date because of passivation phenomena caused by the formation of elemental sulfur or iron-containing precipitates on the surface of the particles (Li, Kawashima, Li, Chandra, & Gerson, 2013). In the 1970s, the Pourbaix diagrams established for the Cu-Fe-S-H2O system at 25°C for low concentrated solutions (Garrels & Christ, 1965; Peters, 1976) agreed that copper and iron are fully dissolved at high potential and in acidic medium (pH < 4). However, they neglected the many stable solid phases that can form in these conditions. In addition, the Pourbaix diagrams of chalcopyrite in water, calculated with two recent databases (FactPS and Thermoddem 2017) associated to FactSage and PhreeqC softwares respectively, show large discrepancies at 75°C (Figure 1). Indeed, at high potential, FactSage predicts the formation of goethite FeOOH at a pH value of 1, while PhreeqC predicts the formation of jarosite (H3O)[Fe3(SO4)2(OH)6] for pH greater than 2.5.

Jan 1, 2019

By S. Fox, Y. Fujita

Increasing demand for rare earth elements (REE) is expected to lead to new development and expansion in industries processing and or recycling REE. For some industrial operators, sending aqueous waste streams to a municipal wastewater treatment plant, or publicly owned treatment works (POTW), may be a cost effective disposal option. However, wastewaters that adversely affect the performance of biological wastewater treatment at the POTW will not be accepted. The objective of our research is to assess the effects of wastewaters that might be generated by new rare earth element (REE) beneficiation or recycling processes on biological wastewater treatment systems. We have been investigating the impact of yttrium and europium on the biological activity of activated sludge collected from an operating municipal wastewater treatment plant. We have also examined the effect of an organic complexant that is commonly used in REE extraction and separations; similar compounds may be a component of newly developed REE recycling processes. Our preliminary results indicate that in the presence of Eu, respiration rates for the activated sludge decrease relative to the no-Eu controls, at Eu concentrations ranging from <10 to 660 µM. Yttrium appears to inhibit respiration as well, although negative impacts have been observed only at the highest Y amendment level tested (660 µM). The organic complexant appears to have a negative impact on activated sludge activity as well, although results are variable. Ultimately the intent of this research is to help REE industries to develop environmentally friendly and economically sustainable beneficiation and recycling processes.

Jan 1, 2016

By Michael T. G. Brown

Syncrude Canada Ltd. has recently completed construction of its ambitious tar-sand mining and processing facilities at Mildred Lake, Alberta. The Syncrude site is approximately 48 km (30 miles) north of Fort McMurray near the west shore of the Athabasca River. The Syncrude operation involves the open-pit mining of approximately 270,000 tonnes (300,000 tons) of tar sand daily using draglines and a conveyor system. Bitumen is extracted from the tar sand, upgraded to oil-gas and transported to refineries in Edmonton and other locations for final processing . The Beaver Creek Dam forms part of the mining facilities for the Syncrude tar-sand mining operation. Water from Beaver Creek is diverted from the open-pit mine site south to the Athabasca River via Ruth Lake and the Poplar Creek Dam. General site layout is shown on Figure I . Design of the dam was completed by R. M. Hardy and Associates Ltd. of Edmonton, Alberta (now Hardy Associates (1978) Ltd) . Construction was undertaken during the summers of 1974 and 1975 under the direction of Canadian Bechtel Limited, managing contractors for Syncrude Canada Ltd. Total length of the dam is approximately 2.8 km (1.7 miles), with a maximum height in the order of 16 m (50 ft) The Beaver Creek Dam is located in a broad, flat, poorly drained valley. About 50 per cent of the site is covered with treeless peat deposits, which ranged in thickness from in excess of 5 m (15 ft) at the east end of the dam to less than 1 m (3 ft) at the central portion. The peat deposits overlie Pleistocene meltwater sediments on top of clay/clay shales of the Clearwater Formation and the tar sands of the McMurray Formation. The peat deposits and high groundwater levels at the site combine to make the excavation and construction of a conventional rolled clay cutoff impractical. For these reasons, the slurry cutoff trench technique was utilized to produce an efficient and effective seepage cutoff under various sections of the Beaver Creek Dam .

Jan 1, 1979

By Richard Dawson

Increasing global demand for coking coal has initiated several new coal mine developments in northeast BC. These developments are able to take advantage of the currently under utilized infrastructure that was put in place during the 1970?s and 1980?s for the Quintette and Bullmoose coal mines; which includes the Town of Tumbler Ridge, a 1,000km rail line to the coal terminal at Prince Rupert and a road system providing highway access to the town site. Coal within the two foothills regions of BC (north-east and south-east) is mined by open pit truck/shovel methods. Optimized mine plans require a thorough understanding of Rocky Mountain structural geology, attention for access in steep terrain, and a related understanding of the geotechnical conditions that control the stability of pit slopes and waste dumps. Thus there is a requirement to properly integrate mine planning with geotechnical engineering considerations. Many of the technical issues are well understood from experience during the past 30 years of Western Canadian coal mining. The challenge is to ensure that the mine plans are able to take full advantage of these lessons learned. The paper will focus on mine planning and geotechnical design issues to do with high angle-of-repose waste dumps and steeply bedded footwall slopes to illustrate the advantage of properly recognizing the important stability control issues during the early stages of engineering evaluations. Case histories from the existing and planned coal mining operations will be presented.

May 1, 2006

By G. Bonin, A. Jamal, G. Preciado, S. Gillis

"Accurate, easy to obtain, and reliable methods of measurement are the cornerstone of shaft and tunnel developments - during their sinking, operation and maintenance, or in some cases, remediation. This paper presents a new methodology to capture existing shaft conditions in such a manner that they can be transferred from the field to a digital copy, where they can be stored and used for engineering design purposes in a space not directly affected by the costs associated with schedule and equipment performance. The methodology utilizes basic principles of excavation alignment (plumb lines and survey instruments) while adding modern LiDAR, geolocation and survey control tools that can more completely capture the surrounding environment. The complete cycle of collection, processing, and delivery of pertinent information underground can take under an hour. During sinking, capturing data as a live stream measurement and being able to assess the alignment of the shaft liner can be critical to meeting rigid design tolerances. As sinking progresses, small changes in alignment or liner deviations can be captured and immediately corrected. Likewise, post-construction as-built conditions can be recorded and digitized, which will allow the mine personnel to compare the proper working condition to the actual condition years later. Observed changes can be identified and planned as future shaft repair works. This methodology has been developed and successfully deployed during the on-going sinking works of the two shafts at the Jansen Potash Project in south-central Saskatchewan and is described in greater detail in this paper.INTRODUCTION Light Detection and Ranging (or LiDAR) scans of the BHP Jansen Production and Service shafts during construction identified sections of both shafts where the internal radius of the temporary primary liner was insufficient to accommodate the tolerances of the permanent liner that was to be installed inside the temporary liner. These locations are referred to as “tights”. The “Tights Removal Program” was designed to collect high resolution point clouds of the shaft, using stringent survey control, that could be compared to the design profile to generate a heat map of locations for removal of up to 75 mm of steel-fiber-reinforced, 70 MPa concrete liner. This work was all on critical path, which made it valuable to save time on the schedule. Because concrete removal was a time-intensive task, it was essential to locate and remove only the concrete that would encroach on the planned permanent liner, while attempting to maximize the amount of cutting time. Removal was carried by a road header attached to a Brokk(R) 160, a small multi-attachment demolition machine."

Jan 1, 2019

The total current inventory of mature fine tailings is estimated to be nearly 850 million m³. Pressure has come to bear on the industry to accelerate its tailings management practices and prevent this inventory from steadily growing. The present paper describes the treatment, management and reclamation of fluid fine tailings. New technologies being evaluated include: i) Thin layered - fines dominated deposits, ii) Deep - fines dominated deposits, iii) Fines enriched sand deposits, and finally iv) water capped disposal in end pit lakes. A brief overview for each of the methods of treatment and disposal for fluid fine tailings is provided.

Aug 1, 2013

By Sylvain Castonguay, Sylvain Pilon

"Operator competency is an important factor in the safe and successful operation of today’s complex processes. Competent process unit operators deliver superior performance and results. In greenfield projects, operator competency is particularly critical, as the lack of specific operations experience must be offset with proven practical knowledge and skills to avoid mistakes that can cost millions in terms of start-up delays, production losses and equipment damage. It is, therefore, important to know precisely what competencies are required for a project or site, and what any gaps in operator competency need to be addressed and improved. The success of plant commissioning, start-up and sustainable operations is directly tied to operator competency. The significant investments required for new projects, the exploitation of more challenging ore bodies, and the increasing complexity of plant operations have placed renewed emphasis on the need for competent operators. Furthermore, many large capital projects are being developed in remote regions, often with ties to the delivery of social benefits for the local population in terms of jobs, training and other development opportunities. While automation and processing technologies have helped do more with less, indicators now point to a bottleneck in human performance limiting operational results.Automation industry development in managing abnormal situations, including solutions for simulation and operator training, has produced applications to provide customized and flexible training methods. This paper will discuss tools to automate the operator competency process in order to guide trainers to effectively teach, measure, control, provide feedback, and monitor operator skills. Today’s competency management solutions can be effectively applied throughout the course of an operator’s professional life, as a guide to hiring new operators, for developing competencies to support operations, and also to develop and refine best practices and share lessons learned."

Jan 1, 2016

By Osvaldo A. Bascur

Industrial complexes rely on measurements of flow rates, qualities, and concentrations for monitoring and optimizing their operation. Corporations use the data from the various sensors and measurements to make business decisions, which affect the profitability of the operation. However, gross errors, due to a variety of reasons like faulty sensors, bad instrument calibration, or incorrect process models may corrupt the actionable information supplied to operations, quality managers, and maintenance personnel. The solution is to use the sophisticated new tools to model the process, sift through the available data to locate the gross errors, and use statistical data reconciliation to validate the sensors and instruments. In this way the data are unified to give the most accurate plant information for use by the monitoring and decision making processes. Most mining and metallurgical plants use predictive maintenance policies based on statistical analysis and special techniques, like vibration analysis, and oil and lube analysis for critical equipment. Process control strategies are installed in several metallurgical sites. All of these depend on reliable and accurate data. The data unification methods validate the individual measurements by using the concept of balances and statistical techniques where each instrument is no longer independent of the other measurements in the facility. This paper refers to the data unification and analysis methods required for profitable plant operations. Continuous improvement and monitoring of the measurement system at the plant and analysis of the reconciled data provide the best information for the decision-making process. On-line gross error detection and elimination methods are required to ensure efficient evaluation of process performance and process optimization. An open discussion of the new methods for gross error detection and data unification will be presented.

May 1, 2001

By R. D. Brown

"AbstractOver the past five years, tax rates in the Canadian mining industry have skyrocketed upward across Canada, as both federal and provincial governments have sought to increase their share of mining revenues.However, the past few years have not only brought high tax rates to the industry, but also a number of important new federal and provincial tax incentives.In large part, these incentives ~ special credits or reduction in tax for carrying out specific exploration, processing or other activities - have helped to moderate the adverse effects of the higher tax rates and have provided inducements for exploration and processing activities which might not otherwise have been undertaken.However, the effectiveness of certain of these incentives can be questioned: our over-all tax structure now consists in large part of punitively high marginal rates with some extraordinarily generous but capricious tax reductions for specific activities and may not be in the best long-term interest of either the industry or the nation.A rational tax structure, with moderate and stable tax rates, together with reasonable incentives confined to activities specifically requiring them, could be a more effective spur to investment than the present tax and incentive jungleIntroductionIN THE YEARS since federal tax reform, the mining industry in Canada has faced a continued escalation in its tax burdens as federal and provincial governments have leapfrogged each other in imposing new and higher taxes on the industry. The result has been that marginal tax rates imposed on mining and processing activities throughout Canada have jumped to hitherto unparalleled levels."

Jan 1, 1977

By Yongfeng Jia, Shaofeng Wang, Danni Zhang

Ferrihydrite is ubiquitous in soils, groundwater and aquatic sediments and is usually classified as "2-line" or "6-line" according to the number of diffuse XRD peaks. It has high surface area and reactivity; therefore, it may serve as a sink for sequestering trace metals, metalloids and organic matters via adsorption and co-precipitation. Although considerable attention was paid to the transformation process of this thermodynamically metastable solid, there are still some controversies on the mechanisms of the formation of goethite or hematite from the ferrihydrite precursor. This work systematically investigated the transformation of 2-line ferrihydrite produced by using different neutralization regent (CaO vs. NaOH) into crystalline products at different pHs (4, 7 and 8), three temperatures (25, 40, 75 °C) and in different media (sulfate vs. nitrate). X-ray diffraction (XRD), Raman, Fourier transform infrared spectroscopy (FTIR) and chemical extraction were employed to characterize the transformed solids as well as the redistribution of Fe between the amorphous and more crystalline phases. The results showed that the transformation product in nitrate media was hematite (major) and goethite (minor), which was independent of pH, temperature or neutralization reagent. In sulfate media, goethite was the dominant solid under slightly acidic conditions (pH 4) with 6-line ferrihydrite as the intermediate product, whereas neutral to slightly alkaline conditions still favor the formation of hematite. Chemical extraction results indicated that there was only ~3 % of amorphous phase detectable after aging at 25 °C for 280 days at slight acidic pH. In contrast,~70 % of the iron remained as an amorphous phase under neutral to slightly alkaline conditions. The results suggested that the pH as well as the reaction media (sulfate ion) plays an important role in the 2-line ferrihydrite transformation process.

Jan 1, 2016

By J. Ji, A. Shi, B. Grcic

Floating copper minerals selectively against iron minerals such as pyrite has been challenging for most copper and copper/gold deposits, and many operations continuously strive to maximise copper recovery whilst meeting target concentrate grades. Maximising grade is achieved by selectively floating copper minerals and rejecting pyrite. This challenge is to minimise copper and gold losses in the roughers if this approach is used. A flotation testing program was conducted by Bureau Veritas Minerals on a high-level pyrite bearing copper/gold ore sample to establish the potential to reject pyrite in the rougher stage, but also maximise copper and gold recoveries, and ultimately final product grades. The test program included feed characterization, rougher and open-circuit cleaner flotation as well as locked cycle flotation tests. The main variables tested for achieving selective flotation of copper and gold were collector type and pH control, through lime addition. Grind sizes used in the rougher and cleaner tests had been established from previous test work. The collectors tested were SIPX, Aerophine® 3418A, Aerophine® 3421, Aerophine® 3422, Reagent S-11192 Promoter, Reagent S-11193 Promoter and FloMin C4150. The two best performing collectors were then tested in open-circuit cleaner tests, with the optimum conditions examined further in locked cycle tests. INTRODUCTION Bureau Veritas Minerals Metallurgical Division was retained by Eldorado Gold Corporation to perform a metallurgical testing program on a high-level pyrite bearing copper/gold ore sample from a gold- copper porphyry deposit to optimize flotation reagent scheme to improve gold and copper recoveries and copper content in the concentrate. The test program included feed characterization, rougher and open-circuit cleaner flotation as well as locked cycle flotation tests. Initially, various collectors were screened in kinetic rougher tests, and over a pH range of 8.5 (i.e the natural ore pH) up to 11.5, using a primary grind size of 80% passing 120 µm. The collectors tested were SIPX (sodium isopropyl xanthate), Aerophine® 3418A, Aerophine® 3421, Aerophine® 3422, Reagent S-11192 Promoter, Reagent S-11193 Promoter and FloMin C4150. The enrichment ratio, which is the ratio of copper to sulfur in the concentrate to that in the feed, was used as proxy for rating selectivity (i.e. degree of pyrite rejection or depression).

Jan 1, 2019

By Joerg Hammerschmidt, Marcus Runkel, Steffen Haus

Given the limited number of new plant construction, focus is turning to the optimization of existing metallurgical roasting plants. To meet the goals of high process efficiency with limited capital expenditure, plant owners are looking for new strategies, including digitization and expert support. As a supplier for numerous roasting, gas cleaning and sulfuric acid plants, Outotec has intensified its effort in recent years to develop solutions to accommodate increasing customer need. This article presents a short review on how Outotec is applying advanced control tools for the fluidized bed industry. Focus will be given on how to transfer the existing technology (used in selected Zinc roasting plants for over a year now) to copper roasting. Outotec has developed the Pretium Roaster Optimizer, a system based on heat and mass-balanced simulation models. Direct experience with this technology will be shared and will highlight similarities to the Partial and Sulfate Copper roasting processes. Pretium detects equipment and plant bottlenecks and provides consistency in process development. The Pretium program combines 24/7 advanced online digitalization tools, along with expert personal support when required. INTRODUCTION Fluidized bed reactors have been used for commercial-scale zinc and copper roasting since the 1950s. While the principles of roasting remain unchanged, over time, the technology has advanced to improve process control of roasting plants. In the past, environmental and safety standards were the driving forces for improvement of equipment and plant design. Today, the emphasis is on plant efficiency and optimization. Another change has come in process control philosophy. While plant control and operation have traditionally been the responsibility of owner/operators, they have now shifted to include both integrated digital tools and specific know-how from engineering companies. This can be seen from the earliest design stages through commissioning and into production, as evidenced by zinc roasting plants in Mexico, Brazil and Turkey.

Jan 1, 2019

By G. Velarde

Agglomeration has as main objective to form a uniform and highly permeable heap for leaching. An inaccurate dosage of moisture during agglomeration leads directly to poor agglomerate quality and segregation of particle sizes during stacking. This causes a heterogeneous distribution of the leach solution inside the heap which invisibly and practically permanently affects the recovery. Unfortunately, only when this becomes serious and the mineral contains an excess amount of fine particles and/or clays then the poor permeability of the pile becomes obvious. This paper is based on the experience of Minera Cerro Verde in the development and application of a quantitative method to control moisture during agglomeration. As the amount of fine particles/clays varies, the quantity of moisture has to be altered in real time. The measurement of agglomerate electrical conductivity is used for it. This concept is based on the sharp change seen in conductivity when the mineral passes its absorption limit. A liquid conductive film then begins to form over the surface of the particles, which leads to the formation of agglomerates through liquid bridges, which are also electrical bridges. Moisture is adjusted to reproduce a value of conductivity established previously and is the guiding parameter. Moreover, moisture amount added to reach this conductivity parameter provides information about the fines/clays relative content for best leaching management.

Jan 1, 2004

By R. Gutray, J. E. Grainger

This paper deals with the use of a cement-deslimed mill tailings mixture for a scraping floor in cut-and-fill stopes at Madsen Red Lake Gold Mines Limited. It describes the mixing and placing procedures and the precautions used with respect to the floor while mining in the stopes. Details of the mix are presented, and advantages and disadvantages discussed. The paper concludes with a brief outline of the costs.

Jan 1, 1966

By Jeremy D. Glennon

A number of exciting challenges, opportunities and unanswered questions remain concerning the chemistry, geochemistry, medical, industrial and analytical applications of gold and its compounds.1 Among the challenges presented is the need for extraction methods for gold, at process and indeed analytical scales, that avoid the use of organic solvents or hazardous reagents. Extensive environmental contamination has occurred in the Brazilian Amazon from the mercury-gold amalgamation process. Major problems with the cyanidation process are the relatively slow dissolution kinetics and the health and environmental problems associated with it. With innovation and technical changes, a cleaner way for solubilising and extracting this versatile precious metal can be found. This cleaner future may lie in supercritical fluid science. Interestingly, geochemical studies of gold solubility and speciation in hydrothermal solutions have highlighted the importance of supercritical conditions and sulphur species in the deposition of gold in natural environments. Gold solubility in supercritical brines is far higher than previously supposed while interest in the high content of carbon dioxide in the mineralizing fluids is growing. 2,3 In recent years, also, there has been a tremendous amount of attention paid in analytical chemistry and in industry, to the area of supercritical fluid extraction (SFE) of organic and metallic species. 4 This interest has been fuelled by the introduction of more stringent environmental control and the subsequent need for cleaner solvents and processes to replace established ones. Carbon dioxide is the substance of choice for SFE because of its moderate critical parameters (Tc = 31oC, Pc = 73atm), inertness and availability in pure form. It is an excellent extraction medium for non-polar and moderately polar species, and with careful ligand design, it can be used for analytical and process scale metal extraction from solution and solid phases. In general, the dissolution of a metal in supercritical CO2 (sc-CO2) requires that the charge on the metal ion be neutralised on complexation by the ligand or through a form of ion pairing (analogous to the situation where metal ions are extracted into organic solvents, such as methyl isobutyl ketone or toluene). In this way, then, many chelating agents such as dithiocarbamates and hydroxamic acids have been utilised to extract metal ions such as Cu and Fe into sc- CO2, the process greatly enhanced by the use of fluorinated ligand derivatives. 5-7 In this review paper, we show that supercritical conditions and complexation with sulphur donor atoms, important in the natural deposition of gold, can form the basis of a clean, eco-friendly chemistry for gold extraction. Analytical scale extractions of gold from a variety of matrices can be conveniently used to assess the efficiency of any new proposed ligand.

Oct 1, 2003

By Ward G. Wilson

Best practice in the design and construction of soil cover systems for mine waste management has advanced extensively over the past two decades. While significant progress has been achieved, we still have little experience with respect to proven performance for cover systems that must last hundreds of years. Some cover designs appear to be functioning well, while at the same time the performance of many more are now being called into question. This presentation evaluates the integrity of cover systems from both a global and local perspective in relation to the uranium industry within Canada.

Aug 1, 2010

By M. Imamura

Sumitomo Metal Mining Co., Ltd. has developed a novel hydrometallurgical process for producing not only copper metal but also iron metal from copper concentrates. Because copper concentrates generally contains the same amount of iron as copper, cost-effective rejection of the iron is a key issue for the development of the process. Conventional hydrometallurgical processes produce a large volume of goethite or hematite for disposal and the residues are not environmentally friendly. In the novel Sumitomo hydrometallurgical process, copper is leached effectively from chalcopyrite concentrates using chlorine gas, followed by purification through solvent extraction and electrowinning for copper and iron recovery. This process has many advantages such as the minimization of the volume of solid waste by the recovery of metallic iron and the production of high purity copper. Iron metal with a purity of more than 98% can be recovered from the purified raffinate. This paper presents the results of the batch and continuous tests of the process flowsheet.

Jan 1, 2006

By D. Rylander

The operation of Quarry and Aggregate sites are similar to factory production, since it contains sequential production processes, tasks and activities to produce the output product. Compared to the plant though, the quarry processes are generally not synchronized and controlled towards the overall throughput of the site in real time. Some quarries control parts of the production but do generally not utilize real-time technologies for the whole site and all its activities. This fact indicates a general improvement potential in increased productivity at quarry sites, but also unsolved challenges for the same reason. The main contribution of this paper is the presentation of a Lean based method for how to describe the processes to identify control improvement potential within a site. The aim of the identified improvements is to increase overall site productivity by optimizing site, fleet and machine utilization towards the overall throughput, and minimizing operational expenses and inventories. Further the paper exemplifies the method?s usability with field studies at operational quarry plants successfully identifying and quantifying potential wastes and improvements. In addition the identified productivity improvements based on increased control and automation indicate challenges and needs in wireless communication and sensing technologies.

Aug 1, 2013