Search Documents

By K. V. Konigsmann

"The mill at Mattagami Lake Mines treats 3,850 tons per day. The mill feed is a heavy sulphide ore. It is composed ofPyrite & Pyrrhotite - 40%Marmatite - 17%Chalcopyrite - 2%Magnetite - 10%Talc and other Silicates - 31%The sulphides are intimately associated with each other and often finely disseminated throughout the siliceous gangue. An abundance of middling particles exist in the circuit and a delicate balance has to be maintained between concentrate grades and metal recoveries.The metal content of the mill feed fluctuates between 0.4 to 0.7% for copper and 6 to 13% for zinc.The flow sheet of the concentrator is shown in Figure 1.Eight sample streams have been selected for on-stream analysis, namely1. Copper Concentrate 2. Copper Cln Tailings 3. Copper Tailings 4. Zinc Concentrate5. Zinc Rgh Concentrate6. Zinc Cln Tailings7. Zinc Rgh Tailings8. Flotation TailingsThe mill feed is not being analysed. Only a very coarse sample could be obtained which would be difficult to pump, and the fluctuations in the copper content are too small in absolute terms to have much of a bearing on circuit operations."

Jan 1, 1969

By J. Ouellet

The authors participated in a study for a new mine shaft in Saskatchewan?s Athabasca Basin where ground freezing is desired to reduce water inflows. Constraints were imposed on the design in terms of permissible water leakage (less than 10 m3 / hour) inside the shaft. Since the shaft goes through highly permeable formations, water control measures had to be incorporated into the design. Ground freezing was selected as the most reliable and proven method for the sinking and a hydrostatic liner design was implemented. While exploring various technological options available for providing a fully hydrostatic liner, the authors came up with a new design concept that offers a more cost effective solution while meeting all the design constraints. The new liner concept is a composite design using concrete and a sprayed-on membrane system. A proof of concept program comprising laboratory testing and field testing was successfully implemented. This paper presents the innovative liner design, as well as the adapted sinking methodology, developed for this type of project. The new concept offers a new cost effective high performance hydrostatic mine shaft liner comparing favorably with traditional methods. RESUME: Les auteurs ont réalisé une étude pour un nouveau puits de mine dans le Bassin de l?Athabasca en Saskatchewan. Des limites sévères sont imposées sur le design en terme de volume d?infiltration d?eau acceptable (moins de 10 m3 / heure). Comme ce puits de mine traverse des formations très perméables la congélation des terrains a été sélectionnée, une méthode éprouvée et fiable. Un design hydrostatique a été choisi pour le revêtement du puits. Dans le processus de design, les différentes technologies disponibles ont été étudiées. Les auteurs ont développé un nouveau concept de revêtement composite offrant un rapport performance/prix plus avantageux que les technologies conventionnelles. Le nouveau design proposé est composé de béton et d?une membrane projetée. Un programme expérimental a été réalisé pour démontrer la faisabilité du concept. Cet article présente le nouveau concept ainsi que la méthodologie de fonçage de puits adaptée. Ce concept innovateur offre un revêtement hydrostatique performant à un cout avantageux par rapport aux techniques de construction utilisées jusqu'à maintenant.

Jun 1, 2012

By H. Huang, R. N. Gow

Acidic treatment of enargite (Cu3AsS4) dissolves both arsenic and copper from the mineral and then attempts to separate them in the leach solution. The reactivity of enargite was examined in acidic to neutral solutions, over the pH range 1-7, to determine a potential range for co-dissolution. Enargite mineral samples from Butte, MT and Quirivilca, Peru were used as working electrodes in a cyclic voltammetry corrosion cell setup, which were then cycled multiple times over -1000 to 1000 mV. Surface reactions and transitions were characterized using in-situ Raman spectroscopy, which were then compared to updated EH-pH diagrams for the copper-arsenic-sulfur-water system from a previous study done under alkaline conditions. The region of co-dissolution is limited to > 600 mV vs. SHE and pH < 1 under the proposed diagram.

Jan 1, 2014

By H. Ishimoto

It always has been a serious issue to improve safety in mine sites, demolition work sites, and civil engineering work sites. Especially, collision accidents caused by construction equipment damage not only the productivity of operations but also the health and life of workers in those work sites. To solve this problem, a variety of worker auto-detection means are developed so far, but they have not still become widely used in actual worksites. There have been two controversial points in the prior methods. One is that they were not enough in respect of the detection accuracy and certainty, and the other one is that the information of the detection results was not comprehensible to the operator of equipment. In this paper, the functional requirements of the obstacle detection system in earth moving work site is redefined at first, and then, it is proposed to apply a stereo vision to the obstacle detection system for an excavator. The system consists of horizontally arrayed two digital cameras with low distortion lens, an image processing controller, and a monitor for an operator in the cab. Stereo vision calculates the depth image from images of two cameras and detects the presence of obstacles, its distance, direction, and dimensions. Sensed obstacles are informed to the operator in the monitor image. Preliminary experiments are conducted with a stereo vision system mounted on a real equipment in a demonstration site. The result shows that two controversial points of the conventional technologies are improved, and that the applicability of this system is validated.

Aug 1, 2013

By J. B. Kwon

For improvement in the productivity of tall building projects, table formwork is one of the main methods that have been adopted for slab formwork. Because the table formwork method is an equipment-oriented construction method, the type of lifting equipment and method of operation considerably affects the productivity and cost of the table formwork. It is also important to make an equipment input plan for completing the table formwork within the time given, according to the structural construction cycle. For performing the table formwork, a tower crane or an independent lifting system, and shifting trolleys, are required. However, if an inefficient equipment input plan is made, exorbitant cost may be incurred. Therefore, the purpose of this study is to analyze the productivity of a table formwork, considering the type and number of lifting equipment and the number of trolleys inputted, and to suggest quantitative data for making a cost-efficient equipment input plan within the construction duration given. It is expected that the results of this research will be utilized as a basis for cost-efficient equipment input planning.

Aug 1, 2013

By Robert B. Parsons

"New Brunswick Finance Minister John Baxter pulled something out of a hat for the mining industry in April, but there is a general concensus in the industry that he should put II back where it came from.The industry has never been in the mood f or progressive rate structures, but that is exactly what New Brunswick &apos;s 1984 budget offers to this depressed sector of the economy.IntroductionThe Province of New Brunswick stunned the Canadian mining community in April with the announcement that the province&apos; s 16% mining tax rate would be replaced with a progressive rate structure effective January 1, 1984 (Table I). The proposed change, contained in the bud get papers tabled by Finance Minister John Baxter on April 17, caught the industry totally by surprise. The move to a progressive rate structure was completely unexpected for a variety of reasons:• Generally speaking, relations between the province and the industry have been relatively good, yet the industry was apparently not consulted with respect to the proposed measure and had no indication that a change of th is nature was coming. This is in stark contrast to the mood which prevailed during the major revamping of the province&apos; s mining tax regime in 1977: at that time, the industry was invited to contribute in advance to the province&apos;s plan for a new tax structure.• The new structure would appear to make th e province less competitive in terms of mining tax rates with Ontario , Quebec, and other provinces, despite indications in the past that New Brunswick is very cognizant of this competitive factor in formulating mineral policy.• A joint report in November 1978 by federal and provincial officials to federal and provincial finance and resource ministers, which was careful not to directly criticize Ontario and Quebec&apos;s progressive mining tax rate structures, recommended that provincial "" tax regimes be examined to ensure the inclusion of appropriate mechanisms to avoid the excessive taxation of cyclical type profit "" , and that ""the federal and provincial governments consider the concern over progressive tax regimes expressed by the industry and examine mining and royalty tax regimes and the income tax regime with a view to alleviating the effect of such regime on the aggregate marginal tax rate"". In this context, any move to a progressive rate structure would be viewed by many observers as retrograde."

Jan 1, 1984

By J. D. R. Neilsen

The objective of the research conducted and presented herein was to determine the effect of pre-established free gas saturation on the sweep efficiency of an isolated inverted five-spot well pattern. The investigation concluded that the ultimate recovery of an isolated inverted five-spot may be slightly increased by establishing a free gas saturation prior to water flooding; however, of more significance is the extreme deviation of the pattern's performance after water break-through from that commonly obtained from developed well patterns. The rapid "water-out" characteristic common to both linear floods and floods conducted in developed well patterns was not evidenced in the isolated inverted five-spot. Instead, the wells continued to produce oil long after breakthrough until ultimate areal sweep efficiencies of four, five, and six hundred percent were obtained prior to the water-oil ratio becoming excessive.

Jan 1, 1962

By Mikael Ramström

In 2002 Atlas Copco Rock Drills AB released the new RCS technology for all of its drill rig types. RCS opened the way for a new generation of computerized drill rigs based on modern, standard PC-computer technology. Drilling accuracy, information logging and reduction in manpower in some types and serviceability, have all taken a quantum leap forward when compared with previous generations of drill rigs. The RCS (Rig Control System) is modularised and distributed is accomplished by means of CAN-bus technology. This technology, which is well proven in automobile applications, forms the communication backbone of the rig. The modularity facilitates almost unlimited possibilities for the expansion and adaptation of drill rig functions.

May 1, 2003

By Chris G. Dobson

Introduction The Britannia mine is at Britannia Beach, on Howe sound, approximately thirty miles from Vancouver. The first claims were staked in 1898, and a local company was formed at that time to develop them. In 1904, Mr. Grant B. Schley became actively interested in the property and in the following year the Britannia Mining and Smelting Company, Limited, was incorporated to operate it. This Company was taken over a few years later by the Howe Sound Company, Limited. The mine comprises five more or less separate ore-bodies, which have produced approximately 20,000,000 tons of ore to date. The East Bluff ore-body, with which the present paper deals, is well suited to large-scale mining by means of carefully placed powder blasts. It covers approximately an acre and lies in the slate footwall, in a bay produced by a fault. The hanging-wall side, on the west, forms the face of the Bluff glory-hole, which extends to the 1,200 level. A portion of this ore was available for breaking into this old glory-hole, below which four bulldoze chambers could quickly be built. Mining of this block is complicated by a very soft footwall, which &apos;runs&apos; badly when broken. In stoping, care is taken to guard against the hazard of dilution by deliberately leaving a small portion of ore on the footwall. Some of this will undoubtedly be lost, but it is hoped to recover a fair amount of it after the major drawing is completed. The deposit occurs in a greenstone which has been highly silicified following brecciation. The chief minerals are chalcopyrite, sphalerite, and pyrite. Concentrates of copper, zinc, and pyrite are made at the mill. The average grade of ore runs 0.7 per cent copper, 1.5 per cent zinc, and 0.03 oz. gold per ton. The rock, which is practically a chert, is extremely hard, but shatters well. Both in stoping and drifting, holes must be closely spaced and powder used generously. Development When development work started in the East Bluff, there were no raises and only one drift on each level in this section of the mine. After blocking out the ore by thorough diamond drilling, a production of two thousand tons per day was set as a goal. To obtain this tonnage from so small an area required a great deal of carefully planned and well timed development work.

Jan 1, 1935

By C. C. Walden, D. W. Duncan, P. C. Trussell

Thiobacillus ferrooxidans released copper from -400-mesh chalcopyrite at a rate of 54 mg/I/hr. Any flotation chemicals remaining on the concentrate did not inhibit the leach rate. Zinc rougher tailings were also leachable. With bacteria, 75 per cent of the zinc and 68 per cent of the copper came into solution. In the sterile controls, only 16 per cent of the zinc and 10 per cent of the copper were released; 100 per cent of the copper and 36 per cent of the zinc were leached from pyrite cinders through the action of bacteria, and 17 per cent of the copper and 10 per cent of the zinc were solubilized in the sterile controls. Less than 0.027 per cent of ~he iron came into solution. The majority of the copper in a converter slag was acid-soluble, but a reverberatory slag responded to microbiological leaching. About 62 per cent of the copper came into solution, compared to 12 per cent in the sterile control. The various factors influencing the rate and extent of microbiological leaching are discussed.

Jan 1, 1966

By Martin Bouchard, Bruno Paillard, Jean-Claude Dubé, André L’Espérance

"A precise analysis of the noise emitted by an aluminum plant has shown that one of the main sources of noise is the noise emitted by an exhaust stack 40 m high and 1.8 m diametre, emitting a pure tone at 320 Hz. Because a classical cost effective solution is not available for this source, active noise control (ANC) solution was investigated.Commonly available ANC systems, how-ever, are not applicable to the chimney considered because the diameter of the stack (f) is too important compared to the wave length(?)of the frequency to control. In fact, until now, active noise control (ANC) has been successfully used to reduce the acoustical energy emitted at the end of ducts in the case of plane wave propagation, i.e. ?/f< 1.7 [1,4].When f> ?/1.7, high order modes propagate in the duct and a single canal active noise control system is not sufficient.This paper presents an ANC system developed to control higher modes in a circular duct. The controller used is based on a multiple-input, multiple-output adaptive filtered X-LMS and allows up to 11 error micro-phones and controls sources. The system has been used in a laboratory on a finite duct of3.5 m long and 0.30 m diameter which corresponds to the same ratio ?/f for the real stack. The efficiency of the system with different numbers and location of control sources and errors sensors has been analyzed. Noise reduction of 15 dB(A) could be obtained with some configurations. Actually, the system is being considered for installation on the real chimney stack."

Jan 1, 1997

By Yin Guangzhi, Song Zhenlong, Li Minghui, Li Wenpu, Deng Bozhi

"Darcy's law is widely used to describe the oil and gas flow characteristics in the multi-pore media reservoir. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the high-velocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore. The gas flow velocities in coal in different deformation stage under different gas pressure gradient were tested and the relationships between gas flow velocity and gas pressure gradient were discussed, which can help us to investigate the transformation conditions of gas linear flow and gas nonlinear flow in coal. The results showed that the gas flow in the coal under low effective stress environment can be described by Darcy's law. The low-velocity non-Darcy flow of gas gradually occurred and the start-up pressure gradient increased in the coal as the effective stress increased. The low-velocity non-Darcy flow of gas also occurred in the coal at the yield deformation stage, however, the start-up pressure gradient decreased as the effective stress increased in this stage. In post-peak stage, the highvelocity non-Darcy flow of gas occurred in the coal under low effective stress environment. The gas flow in the coal gradually returned to be Darcy flow as the effective stress increased. The mechanism of the phenomenon is discussed based on the experimental results. The research results can be used to guide well test analysis and prediction of oil-gas production. INTRODUCTIONThe oil and gas flow in original multi-pore media reservoir are usually regarded as steady and linear processes and can be described by Darcy’s law. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the highvelocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore or workface. The gas flow in the multi-pore media even may be unsteady under some conditions such as gas emission and outburst.The phenomenon of underground water low-velocity flow in clays was deviated from Darcy’s law was found in the end of the nineteenth century (King, 1898). The deviation from Darcy’s law was later reported and investigated more (Swartzendruber, 1962; Miller and Low, 1963). These researches revealed that the start-up pressure gradient exists under low permeability conditions. Klinkenberg (1941) proposed that the permeability constant as determined with gases is dependent upon the property of the gas, and is a linear function of the reciprocal mean pressure. This effect can be explained by taking into account the phenomena of slip, which are related closely to the mean free paths of the gas molecules."

Jan 1, 2015

By K. C. Corin, Z. G. Song, J. Y. Liu, M. W. Zhang, State Key Laboratory of Mineral Processing-BGRIMM, J. G. Wiese

"In the present study effect of grinding media on flotation of two mineral systems have been investigated, viz. sulphide minerals (including a pure chalcopyrite and pyrite mineral, and two different base metal sulphide ores), and oxide minerals (quartz, hematite and cassiterite). It was shown that mild steel media milling produced lower recoveries in the case of chalcopyrite and pyrite, as compared to the case of milling using ceramic media. For oxide minerals, the effects of using mild steel media as opposed to ceramic media were not as significant as was for the sulphides, although, after mild steel milling, at acidic pHs their recoveries were significantly reduced. For two base metal sulphide ores, viz. Nkomati and Dexing ores, the differences resulting from different milling media , although marginal, were opposite for each of these ores.For oxide minerals XPS showed that oxides and hydroxides of iron (e.g. FeOOH) adsorbed on the surfaces of the minerals. In the case of the Nkomati ore, adding Fe2+ or F3+ ions after milling with chrome steel media resulted in reduced talc (gangue) recovery, but increased water recovery and reduced concentrate grades. Further investigations are currently in progress to examine the Fe ions effect on the talc surfaces and froth properties.INTRODUCTIONGrinding of ores is necessary to liberate the valuable minerals from its gangues to allow for their selective recovery during mineral processing such as flotation. The grinding process inevitably involves contact of the ores with the surface of the grinding device and the grinding media. Accompanied by grinding, several phenomena can occur including the grinding medium wear, formation of precipitated species on the ore surfaces, chemical reaction, galvanic effects, changes in the Eh of solution, etc. There is a considerable body of literature on the differences observed in the flotation of various ores after milling using various grinding media. Laboratory studies have used balls or rods made from mild steel, ceramic, stainless steel or chrome steel to investigate the effects of different grinding media on mineral flotation. It is found that the interactions between the ore and the grinding environment can affect flotation separation of sulphide (Wei and Sandenbergh, 2007; Bruckard, 2011), oxide (He et al., 2014) and carbonate minerals (Song, 2009 and 2010). For example, mild steel milling produces relatively high concentrations of Fe ions in the pulp, affecting the recoveries of minerals compared to the case of ceramic media. On the other hand, the stainless steel media or chrome media are reported to be beneficial to the recovery of sulphides, when compared to the cases of using mild or carbon steel media (Rey and Formanek, 1960; Peng et al., 2003a,b; Huang and Grano, 2006; Bruckard, 2011). It is not clear, however, whether these Fe ions may affect the surface properties of the minerals involved or the general pulp/froth behaviour and hence their floatability. In addition, in the study of an low-S PGE ore carried out by Miettunen et al. (2012), forged media grinding in the CO2 atmosphere led to the highest Pt and Pd grades and recoveries, but the high chrome grinding media gave lower flotation recoveries than those using the forged media."

Jan 1, 2016

By Narasimha Mangadoddy, Teja Reddy Vakamalla

"Vertical hydrocyclones are very common in most of the comminution circuits. Inclined cyclones are also found for specific mineral processing applications. In this work, Computational Fluid Dynamics (CFD) technique and experiments are used to find the reasons behind the inclinations effect on hydrocyclone performance characteristics. The water and silica slurry experiments are conducted with 75 mm hydrocyclone at different inclined positions (0-600) to the vertical plane. Corresponding two-phase numerical simulations are performed with Volume of Fluid (VOF) model coupled with Large Eddy Simulation (LES) turbulence model. Multiphase simulations are carried out with Algebraic Slip Mixture model modified with lift, drag forces and Newtonian rheology model corrected with fines for various feed solids concentration. A raise in the under flow solids percentage, cut diameter and a reduction in the water split is observed with the inclination. Electrical Resistance Tomography (ERT) and High Speed Video (HSV) data is used to cross validate the inclined cyclone’s CFD air-core and solids concentration data. Predicted efficiency curves are found in a close agreement with experiments for all the inclinations. Comparison of experimental and predicted flow data clearly follows trend with the literature. Key words: Hydrocyclone, CFD, ERT, inclination, water splitINTRODUCTIONHydrocyclones are devices used to separate or classify particles based on particle size difference in the water medium. Their usage is very wide in chemical, petroleum, mineral and bio industries due to its structural simplicity, high throughput, small volume, low cost and maintenance. Cyclone mainly consists of a cylindrical section followed by a conical section attached to a single feed inlet and two product outlets named vortex finder and spigot. It works on the principle of centrifugal sedimentation. The slurry is fed tangentially to the hydrocyclone, in which larger particles are moved towards the wall and separated by centrifugal forces to the underflow. Smaller size particles follow liquid due to drag forces to the overflow. With its simple structure, the flow behavior inside the hydrocyclone is quite complex. Vertical cyclones are common in practice in most of the comminution circuits. Horizontal cyclones can be found in extreme cases which are for installation convenience rather than for process reasons. Inclined cyclones are also present for specific mineral processing applications. In coal preparation plants, dense medium cyclones are operated near to horizontal inclination of 20 degrees to allow large spigot sizes for sinks removal, self-drain of contents during shutdown. In the phosphate removal, dense medium cyclones are inclined with an angle between 0-90 degrees for better separation of ore and tailings (Liu Feng et al., 2006). Even in the clusters, hydrocyclones are mounted with an inclination around the feed distributor for uniform distribution of slurry and under flow collection. It is believed in mineral processing industry that inclined cyclones would fetch the benefit in number of ways while classifying the material by size. Gravity influences the cyclone performance through the air core size and position variations in large cyclones. It also favours the cyclone operation at coarser cut points without varying any other design and operating parameters. Minimizing fines misplacement to underflow can be achieved with inclination."

Jan 1, 2016

By K. Adham, T. Buchholz

"Significant capacity increases to meet new production demands can often be fulfilled through debottlenecking of an existing production facility, rather than the more expensive option of building new plants and facing new environmental and infrastructure challenges. To achieve that goal, it is important to model and calculate the existing ultimate capacity of each processing plant area, and that of each key equipment sector within the plant areas. This paper describes a methodology of how process modeling tools can be used to simulate the processing steps, how to estimate their existing and ultimate capacities, and how to determine the sweet-spots (minimum cost points) for a plant expansion – leading to a road map of the subsequent debottlenecking project implementation.The debottlenecking technique is presented through a generic work-flow narrative which can be applied to different mineral processing studies, starting with establishment of heat-and-mass balances, drawing a bottleneck diagram, brainstorming capacity increase options, and preparing a cost-capacity curve. Hatch has successfully applied this technique to a number of plant capacity studies, with great benefits to our industrial clients.INTRODUCTIONWith the softening of the metals and minerals prices, and the escalated costs of building new processing plants, it is now economically more viable to improve and debottleneck the existing facilities, rather than build new ones. However, spending new money on old plants requires careful considerations, in order to identify the most economically advantageous incremental steps of improvement and the best potential returns on investment. Process modeling, hand in hand with plant measurements, can identify the best scenarios to balance the three aspects of plant capacity (nameplate, utilization and yield), both at the global and the individual system and subsystem levels."

Jan 1, 2016

By R. P. Kofluk

The nickel-cobalt sulphides produced from limonitic laterite ores by Moa Nickel S.A. in Cuba are refined at the Corefco nickel-cobalt refinery in Canada. Significant economic implications are associated with the refining of precipitated sulphides containing elevated iron contents. The Moa Nickel S.A. operations encompass laterite mining, high pressure acid leaching (H PAL), and ultimately, precipitation of a mixed sulphide product. These processes are reviewed as they pertain to the control of iron and the formation of a mixed sulphide containing nominally 55% Ni, 5% Co and 1% Fe. The contributors to the iron content of the mixed sulphide product are reviewed; the major contributors are the HPAL operation and sulphide precipitation. The precipitation of iron during sulphide precipitation is influenced by the solution acidity, the iron and copper concentrations in the feed solution, and the presence of laterite leach solids. The significance of the copper concentration of the sulphide precipitation solutions is manifested by both physical and chemical modifications of the sulphide precipitates, presumably through the formation of fine copper sulfide seed particles.

Jan 1, 2006

By P. Amelunxen, E. Herrera, L. Hill, J. Vanderbeek

It is well-known that the particle breakage mode that occurs in a semi-autogenous mill is significantly different from that which occurs in a ball mill, enough so to warrant very different lab scale breakage tests and scale-up models. This phenomenon, at the plant scale, leads to changing process constraints depending on the particular properties of the ore. For example, hard or coarse ores might bottleneck the SAG/AG mill throughput, while the ball mills might constrain throughput when milling soft or fine ores. Because the power draw of a ball mill is fairly constant compared to that of a SAG/AG mill, periods of SAG/AG mill bottlenecks lead to increased ball mill circuit specific energy consumption and a finer grinding circuit product size, which together constitute a loss of efficiency of the overall process. Because HPGR circuit throughput is less sensitive to changes in ore hardness, this situation is less common or severe in those circuits. Furthermore, the ball mills are somewhat decoupled from the upstream crushing circuits through the use of surge bins, which also helps to mitigate this effect. As a result, ore hardness variability constitutes a significant cost penalty that should be applied to SAG mill/ball mill/pebble crusher SABC circuits when evaluating the relative economics of different grinding circuit configurations. Nevertheless, the issue is by-and-large ignored, because most current HPGR trade-off studies are based on averaged ore hardness parameters. This paper provides an estimate of the magnitude of this penalty for a typical operation by using Monte Carlo simulation methods and plant data from Freeport-McMoRan’s autogenous, semi-autogenous, and HPGR-based comminution circuits. A case study from an in-house 96K t/d sulphide project is presented to illustrate the concept. It was found that by including variability effects, the trade-off NPV of the HPGR circuit over that of the SAG mill circuit increases to $84 million from negative $33 million, effectively reversing the original decision of selecting a SAG mill circuit for the fixed hardness case.

Jan 1, 2012

By K. H. Poulsen, C. J. . Hodgson

Synvolcanic, layered gabbro-anorthosite sills at Rainy Lake, Northwestern Ontario, reflect a combination of igneous processes including fractional crystallization, wall rock assimilation and possibly liquid immiscibility. Chalcopyrite-pyrrhotite mineralization at the base of the Grassy Portage intrusion accumulated by crystallization of a sulphide liquid during cooling. Upward enrichment of Fe and Ti in this intrusion and also in the Bad Vermilion Lake anorthosite complex culminated with the crystallization of lenses of disseminated to massive magnetite+ apatite+ ilmenite+ rutile. Regional low to medium grade metamorphism and accompanying deformation resulted in recrystallization and local remobilization of ore minerals.

Jan 1, 1984

By Bruce W. Smith

Non-contacting, radioisotope density and level gauges are discussed. The characteristics of the more commonly used isotopes, the techniques of detection and the methods of presenting information are reviewed. The gauge parameters of accuracy, response time and long-term stability are tabulated with reference to calibration techniques and operating requirements. Automatic control systems, both pneumatic and electrical, are used in conjunction with density gauges on filter feeds, and in thickener underflow and heavy media processes. These systems are described. Procedures for installation, start-up and operator training are outlined, along with considerations of preventative maintenance and service requirements. Typical gauge system costs, including capital expenditure, installation, start-up and service, are presented, wherever possible, in order to provide a basis of comparison with more conventional systems.

Jan 1, 1964

By Phil Molloy

"In March, 1968, Skega Ruh her Liners were used to reline the shell of an 8' x 12' Allis Chalmers ball mill.This mill is used to regrind the cyanided pulp from 58i -200 mesh to 92% -200 mesh prior to this pulp passing to the flotation circuit, at approximately 450 tons per day.Before the use of rubber liners, the regrind ball Mill shell had been lined with single wave ni-hard liner!'. These liners had an average life of five years. Ni-hard end liners were used both prior to and during the use of rubber liners, as the life of the ni-hard end liners was about seven years, and it was thus felt that little economic benefit would be realized by lining the ball mill ends with rubber.The rubber lining used has a thickness of 57.15 millimeters and the square shaped lifter bars which are spaced at 14~ inch centres, have a 4"" x 4"" cross-sectional dimension.With the use of ni-hard liners, the consumption of 1 1/4 forged steel balls averaged 1.062 pounds per ton, Using rubber liners the consumption of l~"" forged steel balls increased to 1.368 pounds per ton. Also the level of the ball load which previously had been kept at approximately 18 inches below the mill discharge, had to be increased to approximately 8 inches below the mill discharge in order to effect the same grind.The initial gri4ding performance of the newly relined mill was also poor, until the leading edge of the rubber lifter bars, which were square shaped in cross-section had been worn to a rounded profile. These lifter bars were replaced after 4 years and 3 months of operation.The advantages of rubber liners in our opinion is as follows:"

Jan 1, 1974