Search Documents

By H. Utsunomiya

Most magnesium alloy sheets show low deformability in rolling. Edge cracks and transverse fractures are common difficulties. In addition, rolled sheets show well-developed basal texture <0001>//ND. The texture causes high anisotropy in mechanical properties and low formability in subsequent metal forming. Differential-speed rolling, where the upper and the lower rolls rotate at different speeds, introduces shear deformation through the thickness. Not rolling texture but shear texture evolves in the sheet so that the asymmetric rolling can be a method of texture control. However the primary slip system of the hcp alloy, is basal, the shear texture should be also basal. Differences between the two basal textures, i.e., the rolling texture and the shear texture, have not been understood completely. In this study, conventional (same-speed) rolling and differential-speed rolling have been applied to commercial AZ31B sheets at 623K. Microstructures, textures and mechanical properties of the rolled sheets before/after annealing are compared. It is found that the basal texture is more pronounced by the asymmetric rolling. On the other hand, the asymmetric rolling is effective to decrease the grain size and the planar anisotropy.

Jan 1, 2006

By Ted J. Smith, Stephen E. Kesler

"Zonation patterns are welt developed in the mafic metavolcanic rocks that host epigenetic quartz-carbonate-gold vein mineralization at the Hollinger-McIntyre deposit. Carbonate alteration assemblages are strongly zoned about mineralization. Proceeding inward from background greenschist facies rocks to alteration envelopes enclosing individual veins, the following assemblages are observed:Assemblage I-quartz-albite-chlorite-epidote-actinolite-(calcite)Assemblage II-quartz-albite-chlorite-calcite-epidoteAssemblage III-quartz-ankerite-sericite-(chlorite-calcite)Assemblage IV-quartz-albite-ankerite-sericiteLithogeochemical zoning is equally well developed as variations in whole-rock abundances ofAs, Au, Ba, Rb, and Sb. As and Ba form the most useful zonation patterns, outlining individual ore zones as well as broader trends of mineralization.Gas chromatographic analyses of fluid inclusions in the quartz-carbonate veins indicate that the mineralizing fluid was an H20-C02 mixture. Locally, CH4-rich fluid inclusions are associated with graphitic and/or carbonaceous wallrocks. Fluid inclusions in ore-bearing veins have higher CO2 contents than those in non-ore veins. Extensive sampling and analyses of veins from the area surrounding the deposit reveals a well developed zonation of CO2 contents about the main zone of mineralization. Low CO2 levels (1-2 mole%) in veins are peripheral to the deposit and increase to over 12 mole% in mineralized zones.The observed zoning of the carbonate alteration assemblages is a result of the addition of CO2 to the wallrock, which is consistent with the zoning of CO2 in the fluid inclusions.The zoning patterns delineated in this study are useful in exploration both on a deposit scale and on the scale of individual ore zones."

Jan 1, 1985

By Lloyd A. Clark

"The kuroko deposits, which are extremely variable in size, comprise both stratiform layers of clastic sulphide particles and cross-cutting vein and disseminated components. The ores lie on the flanks of rhyolitic lava domes which have risen from a postulated subvolcanic magma chamber that provided cupriferous hydrothermal solutions and also acted as a heat source driving ground-water convecting cells. The polymetallic sulphides precipitated initially in explosion craters, pipe fillings and feeder veins as rising hydrothermal solutions mixed with sea water. As sulphides clogged the plumbing system, minor phreatomagmatic explosions produced layers of sulphide fragments on the adjacent sea floor. One to ten repetitions of this process produced multiple fragmental sulphide beds. Each deposit formed in a relatively short space of time, because only minor tuff beds are intercalated in spite of active volcanicity in the region. In this model, the heated ground waters convecting through thick piles of acidic pyroclastic rocks leach the zinc, lead and barium later deposited as kuroko ores. As the subvolcanic pluton cools, the supply of silica and copper wanes and the minor counter-circulation cells above the pluton are replaced by main cell fluids bearing zinc, etc. This change in solution flow is abrupt rather than gradual, as the plumbing system is somewhat disrupted by the magmatophreatic explosions that create each ore layer.IntroductionKnowledge of the kuroko deposits ha s greatly expanded during the 25 years since modern recognition of their volcanogenic origin. However, one aspect of the ore s, which may be of unique importance in their genesis, has received little attention. That is the fragmental character of much o f the sulphide ore, which was briefly referred to in a previous publication (Clark, 1971) and is examined in more detail by Barton (1978). Most researcher s have concentrated their attention on or e deposition above and beyond the vent, which is inconsistent with the geology."

Jan 1, 1983

By R. Chen, K. Xia

In deep mining activities, blasting induced compressive stress wave would be reflected as tensile wave at a free surface around the openings, which would facilitate the tensile failure of the deep rock since it is much weaker in tension than in compression. It is thus critical to understand the dynamic tensile failure of rocks subjected to static tension for deep rock engineering applications. A modified split Hopkinson pressure bar (SHPB) system is adopted to load Brazilian disc (BD) samples statically, and then exert dynamic load to the sample through stress wave generated by impact. The pulse shaper technique is used to generate a slowly rising stress wave and thus to facilitate the stress equilibrium of samples during each test. Five groups of Laurentian granite (with tensile strength of 12.8 MPa) BD samples under the pretension stress of 0 MPa, 2 MPa, 4 MPa, 8 MPa, and 10 MPa are tested under different loading rates. The result shows that the dynamic tensile strength of the rock decreases with the increase of pre-tension stress, which is easy to understand because pre-tension stress weakens the rock sample. It is also observed that under the same pre-tension stress, the dynamic tensile strength increases with the loading rate, revealing the so-called rate dependency that is common for engineering materials. Furthermore, it is found that the loading rate sensitivity of the rock increases with the increase of pre-tension stress. A qualitative explanation for this phenomenon is that more microcracks are generated and activated under higher pretension stress, resulting in a more viscous material. Based on the results, an empirical equation is proposed to fit the data and explain the dynamic tensile behaviour of rock under pre-tension stress. A physical model is used to simulate the dependency of the dynamic tensile strength of rock on the pre-tension stress and the loading rate, which is shown to be in good agreement with the experimental results.

Jan 1, 2015

By Holly L. O. Huyck

Disseminated hypogene sulphide mineralization in the Lakeshore porphyry copper deposit (also called the Cyprus-Casa Grande deposit) of Arizona occurs in both a granodiorite stock and associated volcanic rocks. Structural development and vein paragenesis at Lakeshore are similar to other Laramide porphyry copper deposits of the southwestern U.S. Two major structural trends are present: intrusive contacts, copper-bearing potassic alteration veins and major post-mineralization Basin-and-Range type faults trend N-NW, whereas phyllic veins and secondary post-mineralization faults trend N-NE, and deep propylitic veins trend NE-ENE. Lithologic permeabilities, caused by fracturing in all rocks and by grain size distributions in volcanic rocks, controlled the distribution of copper mineralization. Differences in chemical compositions of host rocks did not affect are grade. Structural control, through density of chalcopyrite-rich veins, was the major control of are grade. Fracture density of other potassic vein types did not strongly affect grade. Within volcanic lithologies, permeability, as indicated by grain size distribution, provided a second-order, but significant, control of mineralization.

Jan 1, 1990

By D. P. Fenton

The Phelps Dodge El Paso Rod Mill produces approximately 2.4 million pounds per day of copper rod from a casting and rolling operation. The newly formed rod is treated to remove mill scale and oxides using a sulfuric acid and hydrogen peroxide solution which is bled periodically when the copper concentration reaches 30-35 g/L. The bleed solution is heated to 75° C to destroy the residual peroxide. Copper is then recovered in a 270 cell EMEW electrowinning plant. Clean acid is also regenerated in the EMEW plant and is returned to the rod cleaning circuit. The EMEW plant commissioned in January 2006, has two operators and replaces a copper sulfate plant with fourteen operators. The EMEW plant has a capacity of 1700 kg/day of cathode copper at 2.1 kWh/kg copper deposited. The electrowinning plant operates in closed circuit with the rod mill returning up to 2600 kg/day of sulfuric acid resulting in zero discharge. Use of dimensionally stable anodes (DSA®) ensures that the acid quality is maintained in the closed loop operation. The operating conditions, performance and plant experience of the EMEW copper and acid recovery plant are discussed.

Jan 1, 2007

By Anna Szostak-Chrzanowski, Adam Chrzanowski

"New techniques in monitoring surveys and new methods in the analysis and prediction of ground subsidence are being developed in the Department of Surveying Engineering at the University of New Brunswick (UNB). The new surveying techniques include a telemetry monitoring system developed at UNB in cooperation with CANMET, and use of the satellite Global Positioning System. A generalized approach to the analysis of deformation surveys has been developed which permits an integrated analysis of geodetic and geotechnical measurements in geometrical modelling of ground subsidence. A computer program, FEMMA, has been developed for the elastic and non-linear elastic analysis and the deterministic prediction of deformations using the finite element method.IntroductionResearch and development of new monitoring techniques and new methods in the analysis and prediction of ground subsidence in mining areas is an integral part of a broad research program on deformation surveys which is being carried out in the Department of Surveying Engineering at the University of New Brunswick.The research concentrates on:developmentof a general method for predicting deformations with an emphasis on the use of the non-linear elastic finite element analysis; development of a generalized approach to the geometrical analysis of deformation surveys with an integration of geodetic and geotechnical measurements; and development of new monitoring techniques with an emphasis on continuous data acquisition and application of new space techniques such as the satellite Global Positioning System (GPS).This paper gives a brief report on the progress and recent developments within the above program."

Jan 1, 1987

By C. Boudreault, M. Fortier, S. Fafard

In the forging industry, the increasing trend is to use DC cast billets as forging stock to replace extruded stock. However, there is little technical information available in open literature. In order to gain a better understanding of the behaviour of cast stock during deformation, a study was initiated to evaluate the impact of an homogenisation treatment on the billet prior to cold forging. Axisymmetric upsettings of cylindrical samples machined from DC billets were achieved in order to evaluate and compare flow stresses, crack initiation and propagation. Results show a 30% decrease in flow stress after homogenisation. Observations of the deformed samples show major cracking for the as-cast material. Optical microscopy and SEM observations have related the crack initiation to decohesion around ß -AlFeSi particles and subsequent growth along the constituent path. Homogenisation effectively breaks up and transforms the ß phase, present as platelets in the cast product, into smaller spherodised a-AlFeSi particles. This has the effect of preventing crack growth in the forged product. The homogenisation treatment also resulted in the reduction of Mg and Si in solid solution. The softer matrix generated 29% less die wear when compared to the as-cast structure. Based on the results of this study, it is thus recommended to homogenise cast billets prior to cold forging.

Jan 1, 2006

By Gurupraveen Ramanathan

Shallow-dipping orebodies (45°–60° dip) present significant challenges for underground longhole stoping, particularly due to limited gravity flow, drill misalignment near the footwall, increased potential for dilution from hanging wall overbreak, and deviation from drill string sagging at shallow angles. These geometrical and operational constraints often lead to unblasted ore wedges and excessive overbreak when standard practices are applied. This study develops a structured, data-driven framework to optimize longhole stoping in such conditions by integrating five key focus areas: (1) mining method selection, (2) stope and drift design, (3) drill and blast optimization, (4) equipment selection, and (5) performance evaluation. The suitability of longitudinal longhole stoping was validated for narrow vein geometries using orebody analytics and prior case studies. Geometric modeling was employed to determine optimal stope height (15–20 m) and stope width (1.5–2.5 m), with drift widths adjusted based on orebody dip to maintain drill access and minimize unbroken ore. Drill and blast design emphasized sequential blasting over multi-ring methods to improve void control, reduce wall damage, and enhance fragmentation. Specific burden and spacing guidelines (e.g., 1.8–2.3 m burden; 2.5–3.0 m spacing) were applied based on stope width and dip angle, and patterns were selected based on geometry—dice-5 for narrow stopes, and 3-hole rows for wider stopes. Drill rigs—including top hammer and ITH models from Sandvik, Epiroc, Boart Longyear and CMAC-Thyssen—were evaluated for compatibility with drift dimensions and alignment accuracy. Equipment was matched based on dip, drift width, and the ability to access the footwall at shallow angles. Sensitivity analysis quantified how changes in geometry, drilling accuracy, and blast design affect ore recovery, dilution, and operating cash flow. Results show that tailored drift and stope geometries, combined with proper blasting and rig selection, can boost ore recovery to over 95% and reduce dilution to below 5% in optimal conditions. This methodology offers a practical and economically optimized solution for shallow-dip mining scenarios.

May 4, 2025

By D. J. Farmer

Mining hoists are major components of any underground mine, however, the detailed design work required to get the actual power required for a particular hoist is outside the scope of preliminary feasibility studies. Nonetheless, a hoist is costly. Therefore, an accurate estimate is needed for the design parameters and the power required. There are two methods available, namely, the O’Hara method and the Society of Mining Engineers’ method. Tests were done for both methods employing nine friction hoists and 19 drum hoists currently in use at Canadian mines. The O’Hara method provided unacceptable results for both friction and drum hoists. While, the SME method was designed for American regulations and factors of safety which often differ significantly from Canadian ones, good results were obtained. The two relationships deter-mined were simply to add 5% to friction hoist design and to add 4% to drum hoist design. Modifying the SME method by these two factors will allow the hoisting system determined by the SME method to be within the error for a prefeasibility study.

Jan 1, 1997

By Charles Camsell

If it were necessary to preface a discussion of the mineral position of the Empire by justifying one&apos;s interest in that subject, there are two points that at once suggest themselves by way of vindication. Tremendous Growth of MINERAL Consumption The first of these points has to do with the general question of the world&apos;s mineral consumption. Most thinking persons appreciate in a more or less vague way the vital rôle that has been, and is being, played by mineral products in building up the material side of our modern civilization. But, apart from that casual and almost subconscious appreciation, very few have any precise knowledge of the extent to which the growth and the operation of our vast present-day industrial structure has been made possible by, and only by, a tremendous increase in the consumption of mineral products of all kinds. The increasing use of minerals confronts us today at almost every turn. It does not matter in what direction we look-at the expansion and the change in transportation facilities, in the air as well as on land and on sea; at the increasing mechanization, not only in factory and mill but even in our domestic life; or at the constantly widening use of machinery for all phases of farm production-everywhere we meet the same phenomena of rapidly growing uses of equipment produced mainly from minerals. Without resorting to any tiresome statistics, a few figures may suffice to indicate with what enormous strides the world&apos;s mineral consumption has been advancing. The figures for recent years may be open to objection on the plea that, ever since the outbreak of the world war, conditions have hardly been sufficiently normal to give us trustworthy data-we have been living under extremes either of depression or of abnormal stimulation. During the last decade before the war, however, from 1903 to 1913, the world was moving along in a quietly prosperous manner; and we have figures, or at least reasonably reliable estimates, as to the growth in mineral consumption during that decade.

Jan 1, 1932

By Bian Xue, Wu Wenyuan

In order to recycle the iron and rare earth from the Baotou tailings, a roasting method was developed involving the addition of C, Ca(OH)2, and NaOH, designed to both decompose the rare earth minerals and convert haematite into magnetite and allow its recovery. The effect of various parameters such as roasting temperature, roasting time, C addition, Ca(OH)2 addition, and NaOH addition on the reduction ratio of haematite (iron sesquioxide) and decomposition ratio of rare earth were investigated. The results showed that the reduction ratio of haematite and the decomposition ratio of rare earth could be as high as 85% and 95% respectively when the roasting temperature was 650°C, roasting time was 60 min, Ca(OH)2 addition was 4%, NaOH addition was 3%, and C addition was 1.5%.

Jan 1, 2014

By J. R. Foster

Investigations into the effect of a variety of acid digestions on common rock-forming minerals demonstrated a considerable variation in the proportion of the total metal extracted. A similar situation applies to the analysis of a number of common rock types. In addition, grain-size variation has an effect on the amount extracted by certain digestions. This work indicates that considerable care needs to be given to selecting an appropriate acid digestion capable of determining metal held in particular components of a sample. By using partial extraction techniques, the identification of certain patterns of metal distribution, undetectable by normal methods involving total metal analysis, may be achieved.

Jan 1, 1973

IBI Alliances ? Government ? People ? Academic ? Associations ? Media ? Customers ? Agencies ? Shareholders ? Industry consultants ? Investment Authority ? Geological Survey ? Department of Mines ? People ? Local Residents ? Mineworkers ? Academic ? University of Guelph ? Uganda Vermiculite Institute ? Associations ? TVA ? Organic Certification ? Media ? Canada ? International ? Customers ? Advocacy role ? Agencies ? Regional International

May 1, 2006

By Chigova. Terence

In 2008, Anglo installed the Modular IntelliMine® System at its Kleinkopje Mine (AKK). As part of this deployment, Anglo also used the Change Management Consulting Service offered by Modular to ensure a successful installation. This paper outlines the benefits that AKK has realized through the deployment of the system, including a 15% improvement in tonne/kilometers per hour (TKPH). The mine benefited from the improvements provided by the system almost immediately by utilizing change management to more effectively integrate IntelliMine technology into their processes. This case study includes details about the deployed system, the implementation of change management, and recommendations to ensure success in future projects.

May 1, 2010

By Stephen Esposito

Outline ? Brief Overview of Solid Energy New Zealand ? Need for Integrated Risk Management at Solid Energy New Zealand ? Overview of Solid Energy?s IRM program ? What are the results and key learnings? Overview Of Solid Energy New Zealand ? 100% NZ Government Owned ? Produces 95% of New Zealand?s Coal ? Sales turnover USD150 million per year ? Sold 4 million tonnes of high quality coal in 2003 ? Coking and Thermal coals ? Exported 2 million tonnes of coal ? Significant international and domestic growth expected going forward

May 1, 2004

By Gunther F. Leichtle, James A. Finch, Colin A. Hardie, Cesar O. Gomez

"The recycling of wastepaper has become an important and common process worldwide. Techniques similar to those used in the mineral processing industry are used to produce high quality recycled fibers for use in newsprint. The mineral processing group at McGill University in conjunction with the Pulp and Paper industry (Mechanical and Chemi-mechanical Wood Pulp Network) has adapted one of these techniques, column flotation, for the purpose of deinking wastepaper. This article describes the typical process of recycling wastepaper from a mineral processing point of view. It also presents results from McGill University's flotation column test work at a Quebec wastepaper recycling facility.IntroductionThe recycling of wastepaper has become an important and common process worldwide, including Canada which is now the world's largest importer of wastepaper (CPPA, 1996). Much of the current drive to increase the utilization rate of recovered paper is a reaction to the solid-waste disposal problem that faces many Canadian and U.S. municipalities. The real problem in the disposal of solid waste is not the absolute amount of garbage that must be disposed of each year but this amount in relation to available disposal capacity.Environmental restrictions on the creation of new landfill sites and incinerators (the two main options for disposal of municipal solid waste) have tightened the demand/supply balance in the solid waste disposal market. This shrinking availability of waste disposal sites in the face of increasing population with greater disposal requirements defines the Developed World's solid waste crisis. Not only are there fewer disposal sites available, but the costs of using them is skyrocketing. These factors have increased government regulations mandating recycled paper content in newsprint. Conservation and environmental issues make the current drive for wastepaper recycling a real issue and business opportunity.A key to the success of producing quality recycled fibers from wastepaper is the deinking technology. The production of tissue papers, paper towels and newsprint requires regenerated fibers which are substantially free of ink particles. Of the various options available, mineral processing techniques can offer the most economical, environmentally acceptable and versatile strategies (Yoon, 1993). Today, it is recognized that flotation is one of the most effective processes for removing ink particles in the production of a high quality product. In a collaborative program with the Pulp and Paper industry, the mineral processing group at McGill University has adapted column flotation technology for this purpose. This article will describe the typical process of deinking from a mineral processing point of view (Part A). It will also present some results from McGill University's flotation column test work at a nearby paper recycling facility (Part 8)."

Jan 1, 1998

By N. Shi, T. G. Joseph

ABSTRACT Before any large plant is moved onto an oil sands dominated surface, particularly those surfaces encountered in-pit, it is imperative that the ground be evaluated for bearing capacity. A 2230 tonne mobile in-pit hopper/crusher facility designed for operation in the Canadian oil sands was modeled. This evaluation focused on track and outrigger pad versus ground interactions as the key performance indicators of appropriate ground performance below the unit in both operating and repositioning propel modes. A study of cyclic oil sand behaviour was also inferred from laboratory cyclic plate load data as an extension of the simulation model indications.

Jan 1, 2013

By D. W. Ginsberg, D. Cieplinski

"The lifetime cost of a material handling system, or any mine system, can be reduced through the application of quality engineering. Dynamic simulation is a powerful tool that can be used to enhance the experience and ingenuity of the design team. It cannot only de-bottleneck the system to improve system productivity, but also define critical design criteria to eliminate over-design and reduce capital cost. Eliminating over-design also reduces operating costs by lowering component replacement costs and by ensuring all parts of the system operate at a higher utilization and efficiency. IntroductionA mine owner’s profitability is improved when a mine is developed at the lowest lifetime cost. This cost relates not only to capital and operating costs, but also, to a great extent, on the efficiency and reliability of the operation. These factors are tied directly to the quality of the engineering which depends on the experience of the engineers involved, and their ability to apply known system information in a rational and constructive manner.It is becoming apparent that it is increasingly more difficult to deliver the quality of engineering expected and needed to provide attractive lifetime costs using traditional design methods. Historically, system information has been evaluated based on a limited amount of information to which global rules-of-thumb and the engineer’s personal experience were applied to develop design criteria. However, market forces are dictating that more system parameters be defined and that they be defined more accurately so that the most economical system can be developed. This increase in the volume of information and the need for more accurate predictions is straining, if not already exceeding, the ability of engineers to apply simple global rules of- thumb and to combine all the information in a rational, comprehensive and representative set of design criteria. Furthermore, as proposed system production rates increase beyond established industry practice, the extrapolation of the engineer’s experience becomes more difficult and increases the risk in the proposed design."

Jan 1, 1998

"AbstractThe Sedimentary Basin area of Western Canada, which lies between the Precambrian Shield and the Cordilleran mountain area, covers approximately 800,000 square miles. Sediments ranging in age from Cambrian to Tertiary are present and, of these, horizons in the Upper and Lower Cretaceous, Jurassic, Mississippian, and Devonian have yielded commercial oil and gas flows. Producing horizons in the Cretaceous and Jurassic are sandstone, while all those of the Palaeozoic are carbonate rocks such as red limestone or dolomite (bioherms). Shows of oil and gas have been encountered also in the Cambrian and Triassic sediments.The broad structural features of this vast expanse of sedimentary rocks are the Moose Jaw syncline, the Sweet Grass-Battle River arch, the Alberta syncline, the Foothills belt, the Rocky and Mackenzie mountains, the Great Bear-Slave Lake basin, and the Mackenzie Delta Basin area.This contribution outlines the .stratigraphy and structure of the Basin area, and gives examples of present producing oilfield structures and stratigraphic traps.Part 1.-Regional StratigraphyIntroductionThe vast expanse of relatively undisturbed sedimentary rocks of western Canada has long been recognized as prospective territory to search for oil and/ or gas. This search in western Canada dates back before the turn of the century, but, considering the size of area to be explored and tested, the effort an<l money expended upon it, which, before the recent discovery of oil at Leduc, Alberta, appeared large and fruitless, now seems almost ridiculously small. A check-up of effort and money expended prior to and since the Leduc discovery would undoubtedly reveal that more wildcatting and development has taken place during the last two and a half years than during all previous years combined. The figures would astound not only the average citizen, but many within the industry itself."

Jan 1, 1950