Search Documents

By J. L. Miller, R. W. Burns

This paper sets out the various phases of bringing a merchant bar mill into operation from feasibility consideration through financing, design and scheduling to completion.

Jan 1, 1967

By Robin Sheremeta

Fording Greenhills first acquired GPS (Global Positioning System) technology with the commissioning of a GPS-based dispatch system in December 1994. The second exposure to satellite technology came with the conversion of the conventional optical survey system to a high-resolution GPS system in June 1995. In September 1995,a GPS-based grade control system was tested on the largest shovel (Marion 301 — 58 cubic yard).In January 1996, the system was added to all of the cable shovels (2 P&H 2800s). All three applications of GPS at Greenhills are fully operational and producing positive results. This paper will focus on the practical application of GPS in a mining environment and the effect that GPS technology has had on the Greenhills Mine.

Jan 1, 1996

By G. A. Frame, J. G. Patterson

The 24,000-tpd Frood-Stobie mill grinding circuit operation and control are described. Changes implemented during the past three years to improve grinding efficiency and capacity are discussed.

Jan 1, 1971

By R. D. White

"The Cumberland Basin of Nova Scotia has long been considered a structural basin by virtue of the elliptical outcrop and inward dip pattern of the Pennsylvanian outcrops. Recent published and unpublished data indicate that subsidence began in the late Devonian, perhaps resulting from a graben or rift. The Mississippian sediments which filled the growing depression were continental, lacustrine and marine with evaporites. The cessation of the riftforming processes is recorded by the alluvial swamp-type sediments of the Pennsylvanian which filled the depression. In excess of 25,000 feet of Carboniferous rocks are believed to be present in the deepest part of the Basin. Starting with the rift hypothesis, we can speculate on the kinds of sediments, their location and the structural features present beneath the Pennsylvanian surface. Using surface exposures and a limited amount of subsurface data, we theorize that (1) the Mississippian evaporites acted as glide zones which effectively divided the Basin into two horizontal structural layers. The rocks above the evaporites, responding to Appalachian stresses, formed the long diapiric folds with cores of overthickened evaporites. Below the evaporites the structures are related to movements of the rift floor, compaction closures and structures formed by differential horizontal movements of the rift walls. (2) The rift, in its deeper parts, will have more and a greater variety of marine rocks than the outcrops indicate. Should the rift hypothesis be correct, the possibility of finding hydrocarbons is enhanced."

Jan 1, 1972

By J P. Bolduc, P. E. Pelletier

Preceded by brief general considerations such as the development of the mining industry in. the Province of Quebec, the choice of plant location, the types of problems studied etc., the paper gives a complete description of this new research and treatment center for metallic, non-metallic and asbestos ores. Facilities for carrying out operations in the three sections of the plant -the sampling section, the ore treatment section and the asbestos section -are fully discussed as well as laboratory facilities for (a) the preliminary testing of ores prior to pilot plant treatment and (b) the grading and testing of asbestos fibre. AT THE beginning of the century, the annual value of the mineral production of the Province of Quebec stood at the $2,500,000 level. Twenty-five years later, it was just under $24,000,000. In 1950, half a century later, it was slightly in excess of $200,000,000. But in 1959, in the span of only nine years, it

Jan 1, 1962

By Douglas E. Wolfe, Jogender Singh, Robert Miller, Dong-Ming Zhu, Jeff Eldridge

This paper discusses microstructural changes produced by two novel approaches using electron beam physical vapor deposition (EB-PVD) in which periodic strain fields/microporosity was incorporated within the large columnar grains of Zr02- 8wt.%Y2O3 (8YSZ). The traditional columnar microstructure of partially stabilized zirconia has been slightly modified to produce a lower thermal conductive thermal barrier coating (TBC) by periodically interrupting the condensing vapor resulting in microstructural modifications with diffuse or sharp interfaces and morphological changes on the sub-micron scale without changing the composition of the TBC. These microstructural modifications resulted in a 20-30% reduction in the thermal conductivity, 28-56% increase in hemispherical reflectance, improved oxidation cyclic life (over 100%), and better strain tolerance as compared to standard ZrO2-8wt.%Y2O3 deposited on platinum-nickel-aluminide and CoNiCrA1Y bond-coated MAR-M-247 test samples. The TBC with tailored microstructures were examined by various techniques including scanning electron microscopy (SEM), x-ray diffraction (XRD), steady-state laser heat flux technique, and hemispherical reflectance.

Jan 1, 2004

By J. Keith Haddock

"The Luscar Mine is a metallurgical coal mine located in the foothills of the Canadian Rockies, 41 km southeast of Hinton, Alberta. The mine is operated by Cardinal River Coals Ltd., a 50/50 joint venture between Luscar Ltd. and Consolidation Coal Company of Canada. The mine produces a high quality medium volatile metallurgical coal which is sold on the export market principally to Japan and South Korea. Operations consist of a surface mine with capacity to produce 3.0 million tonnes per year and an underground mine which is currently mothballed due to market conditions.GeologyBedrock units within the Luscar minesite are of Devonian to Upper Cretaceous age. The commercial coal measures in the area are, however, confined within the Lower Luscar Formation. The Luscar Formation consists of a 460-metre thick sequence of interbedded sandstones, shales and coal seams. The sequence is primarily deltaic in origin, and is bounded to the north and south at the Luscar mine by tectonically induced thrust faulting.The only mineable coal seam at Luscar is referred to locally as the Jewel seam. Average thickness of this coal measure is usually 10.5 m to 14 m, although in some areas folding and faulting has produced ""pods"" of coal from 15 m to over 40 m thick while in others the structural deformation has thinned the coal to 3.0 m to 4.6 m. Waste within the Jewel seam seldom exceeds a metre of shale, carbonaceous shale or infrequent sandstone stringers.Reserves and Coal QualityProven surface mineable reserves, based on pit scheduling through 1996, are 50.8 million raw tonnes. An additional 19.2 million raw tonnes are contained in possible extensions to the present planned operations. These surface mineable reserves are considered to be those reserves within 155 m of the surface. Underground reserves, located within 770 m of the surface show that 25.7 million raw tonnes have been proven to date in additon to 27 .5 million indicated and 260 miIJion inferred.Coal specification at Luscar Mine is as follows:"

Jan 1, 1985

By Robin Belley

Outline Introduction Wabush Mines HistoricalBackground Mine and Concentrator at WabushMines High Intensity Magnetic Separators (HIMS) Development of the Manganese Removal Process Pilot Plant Testing Phase Manganese Removal Line 1 Coming Phase: Manganese Removal Line 2 Manganese Concentration Process Development Historical Background 1847: Creation of the Cleveland Iron Company1850: Opening of its first iron ore mine in the Upper Peninsula of Michigan 1965: Beginning of Wabush Mines at Scully Mines, Wabush, Labrador. 1980-1990: Questions raised about how to exploit Scully high Mn Ore (> 2%)Part of the available ore is not saleable due to too high a level of pyrolusite (MnO2) Adding this ore to the resources would be valuable (longer mine life and lower stripping ratio) 1990s: Testwork for Manganese removal Many different processes are studied over more than a decade High Intensity Magnetic Separators (HIMS) are identified as the best technology for Mn removal 2007: Pilot Mn removal line installed Testing carried out through 2007-2008 First Production Line is ordered (2008) 2009: Cleveland Cliffs (now Cliffs Natural Resources)acquire the remaining part of Wabush Mines 2010: Mn Removal Line 1 construction & commissioning Summer 2011: Mn Line 2 Construction

May 1, 2011

By Robin Phinney

Certain statements in this presentation may constitute "forward-looking" statements which involve known and unknown risks, uncertainties and other factors which may cause the actual results, pe1formance or achievements of the Corporation, or industry results, to be materially different from any future results, performance or achievements expressed or implied by such forward-looking statements. When used in this presentation, such statements use such words as "may", "would", "could", "will", "intend", "expect", "believe", "plan", "anticipate", "estimate" and other similar terminology. These statements reflect the Corporation's current expectations regarding future events and operating performance and speak only as of the date of this presentation. Forward-looking statements involve significant risks and uncertainties, should not be read as guarantees of future performance or results, and will not necessa1ily be accurate indications of whether or not such results will be achieved. A number of factors could cause actual results to differ materially from the results discussed in the forward looking statements including, but not limited to, the factors discussed in the Corporation's annual information form filed on March 9, 2011. Actual results could differ materially from those currently anticipated due to a number of factors and risks. These include, but are not limited to, the failure to obtain necessary regulatory approvals, including environmental approval, the failure to secure full project financing, the failure to implement the recommendations set out in the Technical Report, the failure to raise financing to implement the recommendations in the Technical Report, risks associated with the mining industry in general (e.g., operational risks in development, exploration and production; delays or changes in plans with respect to exploration or development projects or capital expenditures; the uncertainty of estimates and projections relating to production, reserves and resources, costs and expenses; and health, safety and environmental risks), decrease in potash prices and exchange rate fluctuations. Although the forward-looking statements contained in this presentation are based upon what management of the Corporation believes are reasonable assumptions, the Corporation cannot assure shareholders that actual results will be consistent with these fonvard-looking statements. These fon\?ard-looking statements are made as of the date of this presentation and are expressly qualified in their entirety by this cautionary statement. Subject to applicable securities laws, the Corporation assumes no obligation to update or revise them to reflect new events or circumstances. This presentation is a market update based on the Corporation's public disclosure and does not form a part of any offer of securities, or constitute a solicitation of any offer to purchase or subscribe for securities. Any purchase of securities in the company should be made solely on the basis of information contained in the Corporation's public record which is available on www.sedar.com .

May 1, 2013

By L. H. McKay

Tailing Dams Three types of dam have been structed to impound tailings from the Allenby mill: 1.- By classifier unit 2.- By earth dam 3.- By direct deposition of tailings The first type, which includes two dams, was built across a shallow valley which sloped down to Similkameen river, just below the mill site. Two earth embankments, one below the other, were built across the valley. Tailings were then piped to Akins classifiers mounted on wooden wheels. The classifiers were set up at one side of the valley and gradually moved ahead on the sand embankment created by the sand discharge from these classifiers, the slime overflow going to settli.ng ponds formed by the dams. Decanting wells were built in the settling ponds by placing four six-by-six timbers vertically in the ground, two feet apart, to which two-by-six tongue-and-groove boards were nailed. The elevations of the ponds were raised, as required, by nailing additional two-by-six boards on the well and bolting on more six-by-six timbers when required. The bottoms of the wells were attached to a covered launder made of three-inch lumber laid on a one per cent grade. This launder carried the overflow through the dam. The second type of dam was built across a long, narrow valley, known as Hitchen's Flat, the upper ~n d of which was about 2½ miles north of the mill. This valley, an ideal tailings site, was 4,000 feet long and from 600 to 800 feet wide. An earth embankment with a concrete spillway through the top was built approximately 28 feet high across the lower end of this valley. Tailings were then dumped into the upper end of valley, with no further expense until the basin was filled up to the level of the flume where this entered the valley. When the upper end of the valley was filled to this point there was still room for more tailings at the lower end. Therefore, a pump was installed to elevate the tailings to build a wall around the upper end of the valley by depositing sands from a launder built up on 20 foot supports and sloping both ways from the pumping station around the upper end of the basin.

Jan 1, 1950

By C. W. Eggert

This paper gives an account of the E.V.O.P. tests made at the Copper Rand mill of the Patino Mining Corporation in Chibougamau, Quebec. The runs were made to acquire an understanding of the method. A description of events, along with conclusions, observations and opinions, is out-lined.

Jan 1, 1967

By M D. Winning

The historical development of the elemental sulphur recovery industry in Western Canada is reviewed for the period 1952 to 1965. A brief technical description of a typical modified Claus sulphur recovery unit is presented. Some predictions are made concerning the future of the elemental sulphur recovery industry in Western Canada. THERE are evidences of sulphur or its compounds having been used for religious and medicinal purposes as far back as we have a recorded knowledge of history. As typical examples, sulphur was burned as a sort of inverse incense to drive away evil spirits at religious festivals, sulphur ointments were used by the early Egyptians to cure eye ailments, and hot sulphur-spring water was used as a cure for a variety of ailments. Thermopyle was called "Hot Gates" be-cause of its fame as a spa as well as a mountain pass. The Romans discovered the sulphur deposits in Sicily and mixed sulphur with bitumen for incendiaries; and, of course, anyone familiar with the travels of Marco Polo knows about the Chinese development of gunpowder, which contains sulphur. In some aspects things haven't changed much today. We still use sulphur-bearing ointments, and we still use the hot sulphur springs such as the one at Banff in Western

Jan 1, 1965

By M. Bouchard, B. Cadieux et F. Goutier

Five phases of ice movement were r es pons ible f or glacial dispersion in t he study area. I ce fl ow directi on changed prog r es s ively from SE to SSW and then to the S. All observed glacial sed iments are associated with a south-southwest to south movement; t hey are grouped, on the basis of their texture, structure, morphology and composition, into four distinct lithofacies. A lithological study of the coarse-grained fraction (4-128 mm) of these lithofacies shows systematic compositional differences. These are: 1) variations in the proportions of local bed rock fragments; 2) variations in the horizontal displacement of the maximum abundance peak of a given lithology relative to its source area, and 3) variations in the length of dispersion trains associated with each lithofacies. Although dispersal trains can obviously be mapped without differentiating li thofacies, studies based on the consideration of lithofacies should give more reliable results than conventional methods.

Jan 1, 1984

By M. N. Collison

"In 1960, with the opening of the Chisel Lake mine near Snow Lake, Manitoba, the Hudson Bay Mining and Smelting Co., Limited, commenced a new phase in their mining operation -that of bringing ore to Flin Flon over 100 miles of railroad.The schedule of operations required to accomplish this, together with an outline of some of the problems of handling ore at 40° and 50,0 below zero, are discussed. The facilities required to thaw and unload from twenty to fifty cars per working day are also described."

Jan 1, 1966

By João Felipe Costa, Jair Carlos Koppe, André C. Zingano

Abstract - Traditional mine planning based on block models built with interpolation techniques such as kriging does not take into account the uncertainty associated with the estimates. These models are inadequate for short-range mine planning. In contrast, conditionally simulated models reproduce the actual variability (histogram) and spatial continuity (variogram) of the attributes of interest. Conditional simulation can be used to address the problem of measuring the uncertainty associated with an estimate. This paper outlines how the sequential Gaussian conditional simulation algorithm can be used to assess uncertainty of grade estimates and also illustrates how simulated models can be incorporated into mine planning and scheduling. A case study demonstrates the efficiency of the method in assessing risk associated with geological and engineering variables.

Jan 1, 2000

By M. C. Bétournay, J. E. Udd

"The legacy of abandoned mines in Canada creates issues that impact on both the health and safety of Canadians and the environment. Solutions to the problems of abandoned minesites require a detailed understanding of site conditions, the engineering solutions which may be relevant, and planning for effective use of the land. In this paper, the authors outline the basic thrusts that have been developed at CANMET to address this problem. These include: multiprovincial agreements to develop a national database; methods of site rendering; a ten-year research program to develop engineering approaches; the review of a large number of case studies; and outlining the associated risks. Examples of the applications of this research are provided in the areas of: municipal, provincial, and federal co-operative projects; site-specific applications; and international linkages."

Jan 1, 1997

By Cindy Schiewek

Industrial injury occurrences are an ongoing concern for Mine Operators. Along with the personal suffering of injured workers comes an increase in compensation and productivity costs. Growing recognition of repetitive stress and bodily injuries, accompanied by recent studies, validates the assumption that a relationship exists between ergonomic injuries and machine design. Intuitively, there is a belief that an ergonomically designed machine will reduce repetitive stress injuries through design and education however; quantifying this belief has been a challenge for Mine Operators. Sandvik Tamrock has undertaken a project aimed at developing a business model to assist in quantifying the benefits of ergonomic intervention. This model focuses on distinguishing and quantifying this method of intervention to allow for a better evaluation of the machine. For simplicity, the project initially focused on the Face Drill Jumbos. The target of the project was three fold: !" Recognition of the cost drivers for compensation; ergonomic injuries !" Identification of the relationship between ergonomic machine design, and the decrease of the negative effects associated with the cost drivers !" Systematic prioritization for ?prevention by design? The project findings substantiate the expected reduction in injuries and compensation claims. Based on all ergonomic intervention studies conducted, each case showed a reduction in compensation cost; through prevention by design, one can reduce the amount of potential risk. The paper addresses the resources and methodology used, along with the findings and its relevance to the issues that face the Mining industry.

May 1, 2003

By P. Cavanagh

Summary This paper discusses the fundamental principles which allow the development of a new method for studying the deformation and failure of metals in terms of 'internal microstrains'. Internal microstrains mechanical and magnetic properties are defined and their influence on of metals is outlined. A research programme at present in progress will determine whether magnetic measurements of internal microstrains give sufficiently accurate values for predicting the performance of metals under service conditions. These magnetic test techniques are also being used to detect the beginning of plastic deformation and to trace the development of deformation processes and failure. Results of the experimental work in each field will be published. Introduction Any attempts are being made to develop a complete theory embracing the mechanical behaviour of metals. In spite of the amount of experimental data available, the theoretical approach is rather difficult, since most of the mechanical properties of a metal are determined by deviations from the pure chemical composition or the perfect crystal. Both types of deviation are difficult to reproduce experimentally and to describe theoretically. In general, there are three main avenues of approach to the problem being followed today.

Jan 1, 1950

By M. Ruel

In today's highly competitive worldwide market, it is becoming extremely important for managers to make sure that all resources are used where needed the most. That way, all resources are generating added value, process control equipments are maintained in an optimal state for best performance, and final product is produced at least cost. Performance monitoring is the only way to ensure that everyone is working on top priorities toward the same goal. How can we add value to these warehouses of data? The data is there and the information is hidden; it is just waiting to be extracted. A process performance monitoring system is able to determine if a loop, a system, a unit, or a plant meets the expected performances. The system prioritizes the areas that need attention. It also provides historical reports of the plant status by areas, by loops, and by identified problems. This information is provided to different categories of users in an appropriate format for each one. The system also includes diagnostics and tools to detect and analyze problems.

Jan 1, 2007

By James D. Hall

THE Dome ore-bodies are more or less isolated and are mined. by shrinkage stoping. An interwoven system of veins is mined at Hollinger '.1.nd requires close filling. Deep mining is the problem at McIntyre. Dome ore contains a large amount of free gold, which is recovered on blankets. An all-cyanide flow-sheet is \lSed in the Hollinger mill. Flotation concentration is an important feature of McIntyre mill operation. Therefore, these three mines afford an unusual opportunity to compare gold mining and milling methods. The purpose of this paper is to describe the conditions existing at the Dome, Hollinger, and McIntyre mines and to outline the mining and milling practice at each property. Figures 3, 4, 5, and 7 are reproduced from the Canadian Mining ]011rna/, September, 1935 (Young, A. W., Mining at Hollinger), and Figures 8 to 11 from the Engineering and Mining Journal, November, 1933 (Keeley, D. E., Development and Mining at McIntyre). The photographs (Figures 6, 12, and 13) are by The Canadian Government Motion Picture Bureau. Diagrams of the several mill flow-sheets, which formed a part of the original paper, are not reproduced here. They will be found in Dorr's Cyanidation and Concentration of Gold and Silver Ores.

Jan 1, 1938