Search Documents

By A. Anderko, V. G. Papangelakis, G. Moldoveanu, G. Azimi, M. Carlos

"OLI Analyzer is a software package that uses the powerful Mixed Solvent Electrolyte (MSE) model to simulate the behavior of multicomponent electrolyte solutions from infinite dilution to the limit of fused salt, and from temperatures below the freezing point up to near critical temperature of the mixture. The software also allows the creation of thermodynamic parameters for new chemical systems unavailable yet in public-domain or commercial software databanks. This communication reviews the basics of the model and provides some examples of modeling hydrometallurgical applications with emphasis on high temperature applications, including calcium sulfate scale formation in autoclaves, high temperature pH inference and iron control. INTRODUCTIONModeling of electrolyte systems has been of particular interest to various industrial processes, such as separation processes (e.g., solution crystallization, extractive distillation, seawater desalination or bio-separations), environmental applications (e.g., gas treatment, wastewater treatment or chemical waste disposal) and hydrometallurgy (e.g., pH control and neutralization, iron control, scaling and fouling of equipment). Using a chemical model, time-effective predictions of various properties of electrolytes can be obtained, which is beneficial not only during process monitoring, but also during process optimization and process scale up. As a result, pilot scale studies can sometimes be eliminated where budgetary constraints exist. Development of such a powerful model requires the use of a speciation-based model, in which solution chemistry is explicitly addressed (as compared with some models that treat electrolytes either as undissociated or fully dissociated systems), despite being computationally challenging. In addition, as a feature of electrolyte systems, speciation equilibria inherently influence the phase equilibria due to complex formation, ion pairing, and acid-base reactions. Therefore, how the electrolyte solutions behave at various conditions may differ significantly due to the non-ideality, which must be carefully addressed to obtain a model that is applicable to a wide range of conditions such as concentration, temperature, pressure and solvent system."

Jan 1, 2012

By G. Bridgstock, S. S. Forbes, E. M. Elkin

"OPERATIONS at Canadian Cop-per Refiners Limited, since the refinery was established in 1931, have been described in previous papers ( 1,2). Since then the refinery has treated the entire copper output of Noranda Mines Limited and Hudson Bay Mining & Smelting Company Limited. With the commencement of production in 1956 at Gaspe Copper Mines Limited, this copper has also been refined. From the start of operations to the end of 1958, the following had been refined: copper, silver, gold, selenium and tellurium.Construction of new buildings and additions to other buildings have been needed to handle increased receipts. The refining capacity has been increased from 112,000 tons of copper per year to a total of 236,000 tons per year.The refinery is located at Mont-real East, Quebec, close to railway and highway facilities. Incoming materials and shipments, with some small exceptions, are handled by rail. Some finished products are sl1ipped by industrial flatcar to the adjoining plants of Canada Wire & Cable Company Limited and Noranda Copper & Brass Limited."

Jan 1, 1960

By A. Zaidi

"The mining and metallurgy industry is highly energy intensive and one of the largest energy users in Canada. Energy costs are also a major component of total production costs in this industry as described in the 1990 Report of The Canadian Industry Program for Energy Conservation (CIPEC). For some plants, energy costs are reported to be up to 30% of total production costs. Therefore, a reduction in energy costs provides an opportunity to improve industry profitability. The specific energy intensity and production costs can be reduced by using modem energy efficient natural gas technologies. In addition, these technologies often improve product quality and increase productivity. Natural gas not only offers economic benefits, but is also environmentally benign as compared to other major energy sources. Emissions of NO"", CO2 particulates and SO2 are lower with natural gas than other fossil fuels.This paper provides a brief overview of some state-of-the-art gas technologies for the mining and metallurgy industry including cogeneration, oxy-air-fuel burners, ceramic immersion tube heaters, direct gas contact process, low NOx burners, and energy efficient liquid heating systems.CogenerationCogeneration is defined as the simultaneous production of electricity or mechanical power and useful process heat from a single fuel source. One of the primary considerations in selecting a cogeneration system is the relative quantities of electrical and thermal energy which are to be produced. Two types of systems are discussed below."

Jan 1, 1993

By L. M. Dwarkin, D. F. Coates

Crows Nest Industries Limited adopted roof bolting in 1963 to improve roof control and to extend continuous miner utilization in one mine. Bolting was held back because anchorage tests gave inconsistent results. The time lapse between mining and bolting was suspected as a cause, and so a test entry was driven and sections of it were bolted as part of the work cycle in addition to the normal timbering. This paper presents the results of the instrumentation of test entries and discusses the utilization of the data to improve mining procedure.

Jan 1, 1967

By C. A. D' Odorico

The zinc pressure leaching (ZPL) plant at Teck Cominco's Trail Operations was started up in 1981 and represented the world's first commercialization of the technology. From the outset, the process was designed to operate using iron-rich Sullivan Mine zinc concentrate. When the Sullivan Mine reached the end of its life in 2002, the ZPL plant underwent a significant process change with the treatment of 100% Red Dog zinc concentrate. Through careful improvements to existing plant processes, controlled changes to plant operating parameters and a rapid adjustment to the modified process by operations personnel, the plant has been successfully converted to processing a feed of 100% Red Dog zinc concentrate. This paper discusses the challenges faced during the conversion and describes the modifications to plant operating procedures, as well as changes to plant processes.

Jan 1, 2004

By Noel Brien, O&apos

General: National Asbestos Mines Limited has operated an asbestos mine and mill near Thetford Mines, Quebec, since 1958. As a result of additional exploration of the orebody in 1962-63, it became apparent that long-range mining plans would have to be revised to allow for a large increase in both ore and waste tonnages. It was decided that the task of checking out possible mine designs could best be analyzed by a computer to obtain data from which an optimum open-pit configuration could be plotted. Object: It was desired to arrive at an optimum open-pit configuration with an over-all pit slope of 45 degrees and a minimum operational width of 200 ft. at the bottom. Calculations were based on assay values from diamond drill holes in cross sections of the mine. The computer's assignment was to select and describe, by coordinates, the optimum cross section for the mine. Mine engineers then assembled the various optimum sections to produce the pit outline. As this would not necessarily result in a practical mining arrangement, the computer also provided alternate solutions,

Jan 1, 1965

By R. Glenn Madill

Western Canada is defined, for the purposes of this paper, as that part of the Dominion bounded approximately by the 95th and 141st meridians of longitude and the 49th and 80th parallels of latitude. It is comprised of Manitoba, Saskatchewan, Alberta, British Columbia, Yukon, and that portion of the Northwest Territories lying to the west of the 95th. meridian. The first magnetic observations made in Western Canada were in the interests of navigation by sea. Observations were made by Captain Middleton in Hudson bay at Churchill and York Factory in 1725, and along the Pacific coast by Captain Cook in 1778 and Captain Vancouver in 1792. The first systematic magnetic survey in Western Canada was made between 1819 and 1826 by Sir John Franklin in his widely distributed explorations. It is of interest to find that while the first magnetic declination observations made in Hudson bay and along the Pacific coast were purely in the interests of navigation, the next investigations, which were made in the Western Arctic, included measurements of inclination and force with those of declination. There was a valid reason for this more complete research into the magnetic field as the construction of declination charts depended on the position of the north magnetic pole. Halley promulgated a theory 1683 that " the globe of the Earth may be regarded as one great magnet, having four magnetic poles, two of them near each pole of the equator, and that in those parts of the world which lie near any of those magnetic poles the needle is chiefly governed thereby, the nearest pole being always predominate over the more remote" . The position of a magnetic pole may be defined as a point where the inclination is 90 degrees and the horizontal force zero. It is obvious that the position cannot be' defined by declination observations alone since, for some distance from the magnetic pole, .the horizontal force is too weak to give directive force sufficient to effect the pointing of a compass.

Jan 1, 1948

By I. Murray, N. Geoffroy

"Buried pipelines, tanks and other similar equipment are almost always present on large scale industrial sites, including in the oil and gas fields. However, as the proverb “out of sight, out of mind” suggests, it is easy to overlook proper maintenance procedures and simply assume that corrosion protection measures in place are working correctly. Unfortunately, this is not always the case, leading to significant environmental damage and loss of production. This paper describes several cases from various industries where buried equipment failed because of corrosion, sometimes with catastrophic results. It also presents various strategies, based on experience and new research, to help predict and prevent damage to underground metallic structures.INTRODUCTION Metallic underground structures are extremely common in industrial and commercial settings for numerous reasons. Burying pipes, tanks, wires and other similar equipment has numerous advantages: it provides significant protection from mechanical damage, frees up ground space that can be used for other purposes, requires little to no support structure and is generally more esthetically pleasing. However, this last benefit can also be considered the most significant disadvantage of underground equipment: becoming invisible and forgotten. While every engineer is aware of the importance of preventive maintenance, it is also human nature to somewhat forget about equipment that is hard to inspect and assume that everything is fine. This is unfortunately not always the case and failures in industrial settings can have extremely serious consequences. While economic aspects immediately come to mind (loss of production, cleanup cost, etc.), failure of underground equipment also results in an environmental and therefore public relations nightmare, especially in the oil and gas field. Leaks that would have been considered negligible in the past can now make national headlines and perfect reliability, while probably impossible to achieve, is now the goal of most companies. While environmental damage (real or perceived) is most often associated with leaks in the oil and gas industry, it can also affect the mining world. For example, the authors have worked on a project where a buried slurry pipeline had ruptured in the ground, causing a release of perfectly inert tailings. While the economic loss was low, the leak was reported in local media and caused a public relations problem."

Jan 1, 2017

By K. Prajapati, P. Hes

Transmission of vibration to the operator from percussive vibrating tools is increasingly of concern in industrial and mining applications. Prolonged exposure to high levels of vibration transmitted via the hand causes disorders known as hand-arm vibration syndrome (HAVS). The vascular component of HAVS is called vibration white finger (VWF) and has a debilitating effect on the hand. Vibration at frequencies below 1250 Hz, a tight hand-grip force and cold environments are reported to increase the likelihood of developing VWF. A vibration damping handle design with patents pending that addresses some of the causes of VWF has been developed and retrofits onto jackleg pneumatic rock drills. The handle is decoupled from the drill while maintaining jackleg twist-grip controls on the hand-grip using a combination of sealed self adjusting hydraulic pistons and compliant materials in series, and a new air control valve. The ergonomics of the hand-grip was also modified by the addition of a polyurethane sleeve with a diameter of 50 mm. The new hand-grip reduces direct cold metal contact and minimizes grip force. Measurement of vibration as the quantity acceleration was made in accordance with international standard ISO 5349. Overall vibration damping in all axes of 50% to 63% was attained at frequencies below 1250 Hz. The dimensions of the damping handle are comparable and its weight is only 100 g heavier than a standard handle.

Jan 1, 2001

By D. B. Nazzer

"ANY DISCUSSION of energy today is incomplete without consideration of nuclear energy. In the Maritimes, with plentiful supplies of coal, with relatively easy availabilty of imported oil brought in to the deepwater terminals, with future sources of large supplies of oil and gas anticipated from under our neighbouring continental shelf, and with the Fundy tides, you may question why nuclear energy should be considered. What follows may not give you a specific answer to that question, but it may provide a basis for better understanding. Energy from the sun, from hydraulic sources and from combustion has been available to man from prehistoric times, for thousands of years, but the most sophisticated source of energy, the actual conversion of matter into energy by man, has been developed entirely within the last one-third century, since the discovery of fission in 1939, and the application to generation of electric power has all been done within a generation or less. The pressure of military needs during and after the second world war was largely responsible for the speed of initial development, by funding and focussing the effort needed to develop the basic technology, and in particular materials. The U.S. defence program yielded, for example, the large-scale isotope separation processes for fissile U'35 and for heavy water. The nuclear submarine program yielded zircaloy, a key structural material for the core of the Canadian Candu type reactor."

Jan 1, 1972

By I. Stanoev, V. S. Stoilov, I. Gradinarov, E. D. Visariev, I. A. Bonchev, Aurubis Bulgaria

"Aurubis is the leading integrated copper group and the world’s largest copper recycler. In Copper smelter Aurubis Bulgaria (Pirdop), the residual copper in the slags from Flash furnace and Converters is recovered by flotation. The slag processing comprises: pit cooling, crushing, two stages grinding (autogenous and ball) and flotation. The copper concentrate is thickened and then is filtrated by vacuum disk filter. The thickener overflow is sent to settler for additional clarification. A resent throughput increase resulted in higher solid content in the thickener overflow due to insufficient thickener area. Different scenarios to overcome the issue were evaluated (new thickener, reagents and reconstruction). An increase of the thickening area by installation of lamella modules was chosen as the most promising option. Three lamella modules (1 m3 each) were installed in conventional thickener for the test. Number of sampling campaigns was done to evaluate the effect on solid content in overflow. Parameters of the dewatering cycle were collected during sampling campaign. The products grain size distribution was defined - thickener feed, thickener overflow with and without lamella. The thickener overflow with lamella modules has 2.12 g/L less solid content. The decrease was 71.8%. According to the tests results, the whole conventional thickener was reconstructed with lamella modules. The thickener area was increased by more than 400 m2.INTRODUCTIONIn Copper smelter Aurubis Bulgaria, the copper in slag from the Flash furnace and the Converters is recovered by flotation. The scheme of slag processing is crushing, two stage grinding (autogenous and ball) and flotation. Till 2010 the grinding cycle in the plant was in two stages: the first stage was AG Mill 70×23 working with a classifier and the second stage was ball mill 3.6/5.5 working with a hydrocyclone. In 2010 a new AG Mill 65×78 with hydrocyclone was put in operation in order to increase throughput of the plant. The second stage of the grinding cycle was not changed."

Jan 1, 2016

By T. Boyd, K. McTaggart, J. Qiu

"Hudbay Minerals’ Flin Flon process plant produces a copper concentrate and zinc concentrate from the three ores it processes: 777, Reed and Lalor. Unlike many Cu-Zn ores, the average Zn: Cu ratio in feed is around 2:1, whereas, in many Cu-Zn separation plants the Zn: Cu feed grade is substantially higher than 2:1. The lower Zn: Cu in plant feed is a challenge for limiting Zn recovery to the Cu concentrate. While total recoveries of Cu and Zn at Flin Flon are very good; selectivity is the key challenge and small changes in ore or plant, can result in quite variable Zn recovery to Cu concentrate, and accordingly, Zn recovery to Zn concentrate. Magnetic conditioning has been shown to be selective between the two paramagnetic minerals chalcopyrite and sphalerite. Statistical testing of magnetic conditioning was undertaken at Flin Flon with the objective of increasing Cu recovery to Cu concentrate without increasing the Zn recovery to Cu concentrate - in effect increasing Cu-Zn selectivity. This has been achieved elsewhere with magnetic conditioning with the probable mechanism being an increase in fine chalcopyrite recovery, and a reduction in entrained, ultrafine, non-activated sphalerite to Cu concentrate. The results did indeed show an increase in Cu recovery to Cu concentrate of 0.8% to high confidence, but the decrease in Zn recovery to Cu concentrate was not to high confidence. This is effectively an increase in Cu: Zn selectivity in the Cu circuit – higher Cu recovery with no change in Zn recovery. However, while there was an increase of 1% in Zn recovery to Zn concentrate with magnetic conditioning, the variability in this parameter meant that this increase, though larger in magnitude than the Cu result, was not to high confidence."

Jan 1, 2019

By John L. Rich

A New Field for the Mining Industry A new field for the mining industry is in prospect. This is the recovery of the petroleum which has been left in the ground in the older oil fields whose yield has declined until they are no longer profitable to operate in the ordinary way. The fact that an oil field has reached the economic limit for operation by pumping does not necessarily 'mean that the oil has ? been exhausted. In many such cases not over one-fifth, or even one-tenth, of the total oil content of the field may have been taken out when this stage has been reached. This means that there exists a large reserve of oil which can be recovered by whatever process best takes advantage of the natural conditions under which the oil occurs. Mine drainage is one of the processes by which this oil may be recovered. Its relative importance will depend partly on the ingenuity and wide-awakeness of mining engineers, and on mining capital. The opportunity is undoubtedly at hand. In order that we may be in a position to judge the possible advantages of mining methods for the recovery of this oil, I have reviewed, on the following pages, the methods now in use, and have discussed the physical conditions of the reservoir rocks in which the oil is found, and the suitability of the various recovery processes, in use or proposed, in the light of these reservoir conditions.

Jan 1, 1927

By G. D. Markland

"The Moose Mountain mine is located in a belt of Precambrian volcanic rocks situated 20 miles north of Sudbury, Ontario. It was the first iron mining operation in the Archean iron-formations of the Canadian Shield.The ore is believed to have been formed in an environment of active volcanism, being part of a pyroclastic and volcanic series where only the iron-formation and chert qualify as chemical sediments. The volcanic environment, subsequent regional tectonics and metamorphism produced orebodies which differ from the main sedimentary iron ranges of the world in such features as continuity, grade, structure and metallurgical characteristics. The orebodies occur as relatively small lenses which have been complexly folded, faulted and intruded by acidic and basic dykesAlthough the basic mining and beneficiation methods are simple, detailed geological control in exploration, planning and operation has been necessary to apply detailed selective techniques to the large-scale open-pit methods necessary in profitable iron mining.The milling and pelletizing processes are sensitive to minor variations in ore grade, grain size, fabric and mineralogy. Although detailed correlations of geological information and mill performance are still not entirely satisfactory, general working relationships have been determined with simple testing procedures. These are of in-creasing use in forecasting production and in ore-blending processes.The application of geology to mining and milling operations at Moose Mountain represents a departure from general practice in iron ore operations."

Jan 1, 1966

By Francis Breton, Daniel Larouche, Pierre Heugue, Rémi Martinez

"Nowadays, in order to fit environmental restrictions, automotive markets are demanding cast aluminum alloys working at high temperature (180–300°C). New generations of alloys are required for higher strength components in engine downsizing or start-stop systems which lead to higher loading and higher specific power and stretch current materials to their limits. Recently, transition metals, such as zirconium and vanadium, have been added as alloying elements into an AlSi7Cu3.5Mg0.1 alloy to improve physical, mechanical, thermodynamic properties with the aim of increasing service life of parts. In such alloys, the best mechanical properties are associated with the formation of precipitates through an optimum heat treatment sequence, including: solutionizing, quenching and artificial aging. This study is focused on the modified AlSi7Cu3.5Mg0.1 cast alloy with Mn, Zr and V additions for high temperature application. The characterization of the cast alloy in this study, firstly, helps to evaluate and understand its performance both chemically and structurally according to their physical state: as-cast or as-quenched. Comparison of precipitation kinetics between a binary Al-3.5%wt.Cu alloy and the AlSi7Cu3.5Mg0.1 (Mn, Zr, V) alloy has been characterized by differential scanning calorimetry, TEM observations and micro-hardness testing. The Kissinger analysis was applied to extract activation energies from non-isothermal DSC runs conducted at different stationary heating rates. The study focuses on the impact of the chemical composition such as Si content on the kinetics parameters.INTRODUCTION Pure metal Aluminum shows poor mechanical properties and its malleability is high, that is why alloying elements are added to the mixture before casting to improve physical, mechanical and thermodynamic properties (Javidani, 2015); such as Silicon (Si) for casting properties (castability, cold crack capability, wear resistance, shrinkage behavior), Magnesium (Mg) and Copper (Cu) to generate precipitation hardening systems. Aluminum hypoeutectic alloys (<12% Silicon) with Cu, Mg additions used in the automotive industry for manufacturing mechanical parts (Larouche & Javidani, 2014) are mostly subject, after casting, to precipitation hardening heat treatment (Mohamed & Samuel, 2012) according to specifications and associated standards. The best mechanical properties are associated with the formation of precipitates through an optimum heat treatment sequence, generally including: solutionizing, water quenching and artificial aging (Manente & Timelli, 2011). Hypoeutectic aluminum-copper alloy with amount of Cu around 1 to 4.5wt% is an elementary case for precipitation in heat treatable aluminum alloys. Researchers essentially focused their work on the full precipitation sequence of binary Al-Cu alloy during aging which is presented below."

Jan 1, 2018

By J. H. Shillabeer

"Rational exploration requires the prior selection of areas possessing excellent geological potential and minimum hazards to commercial development . Within an over-all strategy of grass-roots exploration, two procedures for selecting areas for (i) coal and (ii) metals exploration are described. The procedures explicitly balance infrastructure requirements and environmental concerns for areas of geological merit not alienated in parks and reserves. Through consensus, priorities are attached to those areas meriting closer scrutiny and field reconnaissance.IntroductionMining companies need to know that having made a potentially economic discovery, they will be allowed to develop it with minimum delay and at reasonable cost. The environment for exploration in British Columbia is complex and recent experience suggests that conditions are not becoming any easier. Conflicts over land use issues, preservation and economic development are common. The high cost of exploration requires that the risks should be offset where possible by: (i) carefully selecting the areas in which to work (ii) conducting operations in a responsible manner, and (iii) working cooperatively with the community of interests. This paper concerns the first action: prior selection of areas.To aid exploration planning at Suncor, a procedure was developed to grade those areas of the province possessing favourable geology according to the ease with which a mine might be developed . This had to be done within the constraints of the company&apos;s over-all approach to exploration. This emphasizes ""grass-roots"" exploration of self-generated projects in British Columbia. In addition, having selected a favourable belt of rocks, it is intended to persevere there while steadily adding to the accumulated data base and local experience. Hence, it is intended to concentrate on an area. This implies a long-term commitment to an area which in turn increases the importance of the original selection.Suncor&apos;s search is directed to finding base and precious metals in intrusive and volcanic environments, and export quality coal."

Jan 1, 1985

By Loui Geoffroy, Philippe Gaultier, Martin Piotte, Claude Coache, André Drouin

"Automatic driving at high speed of an underground truck was tested at Brunswick mine in September 1995. Modifications to the truck included: a remote interface to control actuators, front and back video cameras to follow a roof mounted optical guide and proportional hydraulic controls on the steering.The mathematical model of the hydraulic system was adjusted using least square regression. The steering data, used in calculating the regression parameters, were acquired from the moving truck. The automatic steering control used three measured variables: lateral deviation, angular deviation and steering angle. Lateral deviations are obtained using the cameras, which are in continuous view of the guide, while steering angles are acquired from an extensiometer placed at the articulation point of the vehicle. Gain scheduling was used to compensate for vehicle speed and available hydraulic flow. Non-linear characteristics of the modeled hydraulic system were offset using open loop compensation.Speeds up to 23 km/h in forward direction and 13 km/h in reverse were achieved deviaduring continuous testing along one of the mine’s production drifts. Proportional steering was essential in achieving high speeds, as it enabled more precise positioning of the vehicle’s steering direction while reducing the abuses on cylinder and cylinder pins via diminished oscillations about the optical guide at high speeds."

Jan 1, 1997

By G. D. Markland

The Moose Mountain mine is located in a belt of Precambrian volcanic rocks situated 20 miles north of Sudbury, Ontario. It was the first iron mining operation in the Archean iron-formations of the Canadian Shield. The ore is believed to have been formed in an environment of active volcanism, being part of a pyroclastic and volcanic series where only the iron-formation and chert qualify as chemical sediments. The volcanic environment, subsequent regional tectonics and metamorphism produced orebodies which differ from the main sedimentary iron ranges of the world in such features as continuity, grade, structure and metallurgical characteristics. The orebodies occur as relatively small lenses which have been complexly folded, faulted and intruded by acidic and basic dykes.

Feb 1, 1966

By K. Kryst, K. Elkayar

The increasing need to process lower grade contaminated copper concentrates and simultaneously produce higher purity copper cathodes necessitates a more diligent control in the electrorefining process. Ion exchange processes can be a powerful tool in controlling electrolyte impurities to ensure trouble free operation within the tankhouse and to help maintain cathode purity. In addition, some impurities can be recovered as a value added product. The use of a short bed ion exchange process provides a unique opportunity for impurity management in copper refineries. Several metals are discussed in this paper, including Sb, Bi, As and Ni and their methods of control and recovery within the copper electrolyte circuit. INTRODUCTION To produce a high purity copper product by electro-refining a copper electrolyte, it is important to control the concentration of impurities such as arsenic (As), bismuth (Bi), antimony (Sb), and nickel (Ni). These impurities are introduced into the electrolyte from the copper anode and can affect the copper product and the production operation. The presence of As in the copper product results in a lower electric conductivity and reduced workability of the copper. High levels of Bi in the electrolyte will result in a copper cathode product containing Bi. High Sb concentration will cause undesired floating slimes. A variety of methods have been developed to control the level of these impurities in the copper electrolyte including precipitation, liquid extraction, and ion exchange. These impurities can be recovered and used. This paper discusses novel methods that utilize short bed ion exchange technology to control these impurities. Also, the use of ion exchange to recover acid from the liberator cells bleed for reuse in the tankhouse is reviewed. SHORT BED ION EXCHANGE Short bed ion exchange technology has been employed extensively in the metal finishing industries for over forty years. Unlike conventional ion exchange, short beds are fixed beds without freeboard space. The application of short bed technology results in significant benefits when compared to conventional ion exchange. The resin used in this technology has a significantly smaller diameter than conventional ion exchange resin. As a result of the smaller resin size, exchange kinetics improves dramatically. This facilitates operation at higher flow rates and the use of smaller beds with a small mass transfer zone length. Smaller beds are especially important for applications that use chelating resins due to the high cost of the resin.

Jan 1, 2019

By C. Dodds, R. S. Ferrari-John, The University of Nottingham, G. Dimitrakis, J. Katrib, A. R. Batchelor

"Sorting technologies have the potential to reduce energy use in comminution by rejecting uneconomic ore before feed material enters the mill. However, a major challenge for sorting porphyry copper ores is providing a basis of discrimination between valuable and non-valuable fragments, due to their complex mineralogies and textural features. Microwave heating in combination with infra-red detection (MW-IR) has been shown to provide upgraded feedstock for certain ores at bench scale. Selective heating of copper sulphide minerals compared to the gangue leads to an increased thermal response for valuable fragments, providing the basis for sorting.Rapid scale up of MW-IR from bench scale to a 100 t/h continuous pilot plant facility has been facilitated by the design of microwave choking structures to allow continuous operation at industrially meaningful throughputs, whilst meeting health and safety and electromagnetic compliance standards, and the integration of materials handling with electromagnetic systems.Laboratory batch testing on a pilot scale microwave system has been undertaken to investigate the thermal response of copper ores under industrial conditions, at microwave energy inputs up to 1 kWh/t. These results provided the operating window and recommended test conditions for the continuous pilot plant. Sortability curves predicted in the laboratory are in good agreement with separations achieved during continuous pilot plant operations. The potential microwave sortability of a number of ores has been studied, allowing informed decisions to be made about potential ore candidates based on mineralogy. Future development of the technology will be underpinned by the creation and validation of scale up concepts for 1000 t/h operations. Understanding the value proposition for individual sites/applications will be central to unlocking the potential economic and environmental benefits of microwave sorting."

Jan 1, 2016