Search Documents

By P. R. G. Brandão, E. E. Ferreira

The presence of metallic cations in solution will affect the aggregation or dispersion of the fine hematite particles, depending on the type of cation adsorption: either specific or non specific adsorption. In this work, the zeta potential measurements were carried out on a sample of pure hematite as a function of pH and metallic cations concentration (Ca2, Mg2+, Mn2+, K+, Na+ and Al3+). The objective of these studies was to clarify the effect of these metallic cations on the surface chemical properties of pure hematite. The cations K+ and Na+ adsorbed as non-specific species and caused only the reduction on the values of zeta potential (in terms of absolute value) over the entire range of pH values tested. For the Al3+ cation, in the acidic pH range it adsorbed as a specific species and increased the zeta potential values. The cations Ca2+, Mg2+ and Mn2+, adsorbed as a non specific species at pH levels less than 6.0 and caused the reduction of zeta potential due to the compression of the electrical double layer. However, for pH values greater than 6.0, these cations adsorbed as a specific species causing the zeta potential to increase and became more positive as the pH value increased (alkaline). This effect could be due to the adsorption of some hidroxy complex species of these cations, which contributed to the positive charge. The effect of metallic cations (Ca2+, Mg2+ and Al3+ concentration, at pH 4.0, 7.0 and 10, showed the following results: a) at pH 4.0, increasing the concentrations of Ca2+ and Mg2+ resulted in on a small reduction in the value of the zeta potential. At this pH, increasing the concentration of A131 cations caused the zeta potential to increase due to specific adsorption of a negatively charged Al3+ hydroxy complex b) at pH 7 and 10, increasing the concentrations of Ca2+ and Mg2+ caused the zeta potential to change its charge from negative to positive.

Jan 1, 2004

By Fazel G. Jahromi, Ahmad Ghahreman

"Several studies were performed on the atmospheric leaching of copper sulfide minerals in the presence of activated carbon and a new catalyst, AF 5. AF 5 is a carbon based catalyst with similar properties to those of activated carbon however much better mechanical properties. The activated carbon surface chemistry has been investigated in various studies; however the connection of the surface chemistry of activated carbon and AF 5 with the sulfide minerals during the atmospheric leaching process is not well-understood yet. Based on the surface analysis, AF 5 showed higher surface area than activated carbon (AC). Adsorption and oxidation of copper, arsenic and iron ions in the presence of different activated carbon were investigated. Adsorption properties of both catalysts were similar and 18-24% of iron, 12-18% of copper and 10% of arsenic adsorbed on the catalysts surface form 5 g/L Fe(III) and Cu(II) and 2 g/L As(III) at 80°C. In oxidation experiments, both catalysts reduced Fe(III) and Cu(II) ions and re-oxidized the reduced species in the presence of oxygen and oxidized As(III) ions. The addition of oxidizing ions can enhance the oxidation process kinetics and increase the catalytic capability of carbon.INTRODUCTION Hydrometallurgical processes of copper sulfide concentrates are under development and various different methods have been proposed to increase the atmospheric leaching rate of copper sulfide minerals. These methods include using different media, reagents, and catalysts. Among different methods, leaching of the copper sulfide minerals in the chloride media has some advantages over sulfate media. Smaller scale of operation, increased leaching rates, and lower sulfate formation are some of the benefits of the chloride leaching media over other similar media. Moreover, using ferric and cupric ions as oxidants and utilizing activated carbon as a catalyst has been proven to enhance the leaching rate of copper sulfide minerals effectively. Activated carbon (AC) and AF 5 (micro porous carbon based catalyst) are two of the most efficient and practical catalysts in copper sulfide leaching processes. AC can enhance the copper recovery of enargite in chloride media from 69% to 92% after 96 hours of leaching under the similar conditions (Jahromi & Ghahreman, 2016). It has been shown that AC at acidic pH can generate hydrogen peroxide in the presence of oxygen which can leach copper minerals (Ahmumada et al., 2002)."

Jan 1, 2017

By M. J. Merwin

Heat treated seamless tubular products are processed in a fashion that can be easily modified to produce dual phase microstructures, through the implementation of intercritical soaking prior to quenching. Dual phase steels are known to possess low yield strength compared to tensile strength. The steel line pipe market is interested in low yield-tensile ratio materials for application in reel barge pipe laying operations. In the current work compositions of commercially produced material already in use for the line pipe market were examined and dual phase microstructures were successfully developed. The microstructure and properties of the materials were found to be stable over the range of intercritical temperatures employed. Tempering temperature and, somewhat unexpectedly, small chemistry differences were found to have the largest influence on properties. Excellent toughness performance was observed in samples tempered at temperatures in excess of 550°C. Tempering in this temperature regime produced materials with strength suitable for application as API X60 line pipe. A difference in tensile strength between steels of similar chemistry was observed, and is not fully understood at this time. Welding performance was considered through simulation of three regions of the heat-affected zone. Neither intercritical temperature, nor tempering temperature, were found to have a significant influence on the heat-affected zone properties. The peak temperature achieved in the thermal cycle was the only significant factor. The hardness of the heat-affected zone was found to increase continuously with increasing peak temperature. While toughness was found to be low for both partially-transformed and coarse-grain heat-affected zones, the toughness of the fine-grained heat-affected zone was substantially better. Based on the results found in this laboratory study, a limited production trial is expected.

Jan 1, 2005

By P. Shibley, P. R. Clarke

Since this was an interim report of the initial operation of a long term project it is not available for publication. It is expected when the project is completed a full report of the work will be published.

Jan 1, 1968

By A. Y. Senchenko, S. G. Rybkin, A. V. Aksenov

In gravity processing of gold-containing ore the target produced concentrate which is high gold grade primary concentrate contains a significant amount of cassiterite (SnO2). The plant attempts aiming at concentrate processing using a standard pyrometallurgical technology did not provide any positive results. The present paper is dedicated to development and testing of improved technology for pyrometallurgical processing of rich gold primary concentrate with high cassiterite content. According to material composition study primary concentrates produced at the plant contained 1.5–2.0% Au, 0.1–0.3% Ag, 55–65% SnO2, 20–25% Fe2O3, and 10–15% Fe3O4. The developed technology included alkaline nodulizing of primary concentrate mixed with sodium hydroxide and carbonate at 350–650°? with cake production. In blend nodulizing stannum and iron passed into sodium stannate (Na2SnO3) and sodium ferrate (NaFeO2) respectively. The blend of cake and fluxing agents was smelted at 1,150–1,200°? resulting in dore gold and slag production. Sodium stannate with 360°? melting point is well dissolved in slag system Na2OSiO2- B2O3-CaO. During plant tests 18.5 kg of high gold grade primary concentrate were processed, 1350 g of dore gold and 75 kg of slag were produced. Dore gold contained 16.5% Au, 0.95% Ag, 78.0% Sn, 3.1% Fe. Slag contained 12.4 g/t Au, 6.7 g/t Ag, 9.8% Sn, and 5.6% Fe. Gold recovery to target alloy was equal to 99.58 %, 87.8% of Sn passed into slag. This new technology was accepted for application at the plant.

Jan 1, 2016

By R. Argane

In this work we assessed the geochemical behavior of concentrator tailings deposited at the abandoned mines of Zeida and Mibladen (Upper Moulouya, Morocco), using physico-chemical analyses, mineralogical characterization, acid base accounting and weathering cell tests. The aim of the study was to evaluate mine drainage quality and to assess metal mobility from these concentrator tailings. Chemical analyses show that the Upper-Moulouya abandoned tailings contain relatively high quantities of lead (0.261 to 0.594 % wt). Mineralogical analyses reveal the abundance of neutralizing minerals (calcite, dolomite, ankerite, and aluminosilicates) which influence mine drainage and metal mobility in mine tailings. Leachate analyses from weathering cell tests show alkaline conditions, small conductivity values, and low solubility of Pb-mineral phases. According to these results, abandoned mine tailings in the Upper-Moulouya district have very low potential for generation of contaminated mine drainage and for leaching of heavy metals. However, the inhalation of tailings exposed to winds generate dust problem facing the local population and may cause health consequences.

Aug 1, 2013

By L W. Morley

The Division is concerned with physical methods as applied to geo-logical research and mapping. An at-tempt is made to describe long-term goals, illustrated by examples of projects in the fields of aeromagnetic interpretation, palaeomagnetic re-search, Pleistocene and groundwater geophysics, seismic surveying, electromagnetic research and instrument development. Cooperative projects in surveys and research, with universities, private companies and provincial organizations, are frequently undertaken. An outstanding example of this is the recently approved Federal-Provincial Aeromagnetic Survey Plan, the purpose of which is discussed both from an economic and a scientific point of view. HISTORY OF THE DIVISION M AGNETIC, electrical, seismic and gravity methods, as a means of extending the geologist's sphere of observation beyond the head of his hammer, came into wide-spread use for the first time after World ?war I. Interest in these methods was aroused amongst geologists of the Geological Survey and, in 1928, a group of these geologists and university

Jan 1, 1963

By R. D. Westervelt

IN JULY 1954, the first iron ore from the deposits in the Knob Lake vicinity was mined and shipped to Seven Islands. The beginning of the production may well be the greatest advance in Canadian economy in the past fifty years. In 1955, the Canadian iron ore output was more than twice that of 1954, an in-crease due principally to the iron ore shipments from the Knob Lake area. Previous to this, Canada's iron production was 1.85 per cent of the world's output. Now, this percentage has risen to approximately 5.5 per cent and shows every indication of increasing further as the production rate from the area is increased. In 1955 the Iron Ore Company of Canada shipped over 7 million tons of iron ore and expects to ship over 10 million tons in 1956. Present facilities may be enlarged to handle up to 20 million tons per year. If the expected I 0 million tons per year are exported, Canada's iron exports will be second only to her wheat and newsprint exports. Before production began from the Knob Lake deposits, years of development were necessary in the area. Geologists spent several summers mapping the general area in order to unravel the complicated stratigraphy and petrology. Particular attention was paid to the mapping of the iron formation and all stages of alteration from fresh iron formation to ore were observed.

Jan 1, 1957

By B. Grinbaum, A. Mazuelos, F. Carranza, N. Iglesias, M. Avila, J. L. Lozano, G. Perez, R. Romero, M. \/aliente

Following a failure of a tailings pond darn at a mine in Andalusia, Spain, a huge effluent stream, that contained about 1 g/1 Zn and significant amounts of ferrous, ferric, calcium, copper, aluminium and manganese cations has to be treated, to prevent pollution of a nature reserve. EGMASA, as the regional government environmental agency, suggested to improve the current depuration process by recovery of the Zn from the effluent. A solvent extraction (SX) followed by electrowinning (EW) was proposed and developed to remove zinc.. A pre-treatment stage consisting in bio-oxidation of ferrous iron by using a bacterial process followed by an alkaline precipitation was employed because iron in the effluent is incompatible with both the SX and the EW processes. The SX process was developed successfully at the laboratory scale and verified in a pilot plant on-site, using two Bateman Pulsed Columns for extraction and stripping of zinc. The results were satisfactory obtaining a recovery of 90% of Zn. The process was suitable for industrial application.

Jan 1, 2008

By Dart Wantland

"AbstractThe scope of geophysics in civil engineering and the nature of exploration geophysics are briefly discussed. Engineering problems amenable to geophysical attack are illustrated by specific examples. The various methods available, accuracy of results, and costs are treated. The possibilities of new uses of geophysical techniques are pointed out.IntroductionTHE SCOPE of geophysics in engineering is different than in oil or mining exploration. In civil engineering, geophysics solves specific problems; as for example, what is the depth to bed-rock along the axis of a proposed dam? The area to be surveyed is of limited extent, and the subsurface information .sought is relatively near the surface. The engineering geophysicist is not called upon to investigate geological basins or extensive mineralized areas or to probe for data to thousands of feet in depth. The geophysical tools employed in the three fields are, however, quite similar; the differences are mainly in the objectives.The Natural Geophysical ExplorationThe terms geophysics and geophysical exploration have been used heretofore and will .be employed in what follows. The question is, therefore, What is geophysical exploration?Geophysical exploration is a line of field work where measurements are made at the ground surface with special instruments to get geological subsurface information. Briefly stated, geophysics is a form of exploration that supplements geological work. It is a blend of physics and geology since physical measurements are made •at the surface of the ground that can be interpreted in terms of subsurface conditions."

Jan 1, 1953

By T. Lu

Microwaves have considerable potential as an energy source in both mineral processing and metals extraction. In this research, the utilization of microwave radiation for the heating of a gibbsite type bauxite ore was investigated. Firstly, thermogravimetric studies were performed in order to characterize the dewatering processes of the ore. Secondly, both the real and the imaginary permittivities, which are the fundamental properties that determine the interaction of microwaves with any given material, were measured for the bauxite ore as a function of temperature. The changes in the permittivities were shown to be related to the dewatering processes. Subsequently, the effects of operating variables such as processing time, sample mass, particle size, microwave power, sample bulk density and carbon and magnetite additions on the sample temperature in a microwave field were studied. The results showed that under suitable conditions the bauxite ore could be readily heated. Therefore, there is considerable potential for the application of microwaves for the heating of bauxite ores.

Jan 1, 2007

By Dong-min Lee

As the construction industry is becoming more large-scaled and complex, the BIM technology has been utilized throughout the industry. Since 2008, the construction industry in South Korea (Korea) has required carrying on BIM-based project continually. According to this trend, BIM S/W market, as well as BIM library market is also gradually activated. Many countries have already been establishing Web-based BIM library market, also Korea has been trying to establishing this Web-based BIM library market. In this study, through market research of Web-based BIM library market of advanced countries including the U.S.A. and U.K., establishment strategy of BIM library market to be derived by late starters that introduce BIM such as Korea, Japan and China was deduced based on current establishment status of BIM library market in Korea. In addition, deal with an issue that a clear revenue-sharing system between business principals of Web-based BIM library market is not available at the current stage was presented as a factor of inhibiting activation of BIM library market. So in order to offer a reasonable revenue-sharing strategy in BIM library market as conceptual level, a methodology and process of applying Game theory being used for deriving. It is expected that a reasonable revenue-sharing model between business principals would be presented as its standard of BIM library market to be more activated in the future.

Aug 1, 2013

By Isabel C. B Rodrigues, Flávia D. Reis, Versiane A. Leão, Rosa M. F. Lima

Attention has been focused in recent decades upon the precipitation of metal sulphides from acid mine drainage (AMD) and pregnant leach solutions, due to the advantages of the sulphide precipitation process over traditional methods employing hydroxides. The aim of this work was thus to explore technologies for copper precipitation using either Na2S or biogenic sulphide. The recovery of copper sulphide was improved when the initial pH of the solution containing each metal was 4 or excess sulphide was employed. In such, a condition the removal efficiency was 99.9%, corresponding to a residual level of 0.1mg/L for copper in solution. Kinetic parameters for precipitation were determined from the particle size distributions using the method of moments, where the growth and nucleation rates, as well the agglomeration kernel, were calculated. The biogenic sulphide was a suitable alternative to sodium sulphide for copper removal as either sodium sulphide and biogenic sulphide can be utilized to precipitate such a metal allowing the effluent to be compliant with environmental legislation.

Jan 1, 2014

By G. A. Sutton

"At the San Manuel mine (Arizona, USA), in-situ copper leaching of a copper porphyry deposit was carried out from 1986 to 1999 during underground and open-pit mining. In 1993–1994, well¬field testing of the supergene zone, composed primarily of chrysocolla and copper-rich clay minerals, led to estimates that 52% of the acid-soluble copper (ASCu) could be recovered during in-situ leaching; however, the actual recovery from zone 6, which had the longest leach history, was approximately 42%. Comparing drillcore assay data from holes drilled before and after leaching also indicated an approximate recovery of 42%. The discrepancy between the predicted (52%) and actual (42%) recovery is probably related to several factors, including difficulty maintaining fluid saturation, channelling effects, and gypsum precipitation. ¦ KEYWORDS Copper oxides, in-situ leaching, Modelling, Porphyry, Solvent extraction and electrowinning (SXEW), Well-to-well RÉSUMÉ À la mine San Manuel (Arizona, États-Unis), on a procédé de 1986 à 1999 à la lixiviation in-situ de cuivre d’un gisement porphyre cuprifère pendant l’exploitation minière souterraine et à ciel ouvert. En 1993 et 1994, des essais effectués dans des champs de captage de la zone supergène, composée principalement de chrysocolle et de minéraux argileux cuprifères, ont abouti à des estimations selon lesquelles on peut récupérer 52 % de cuivre soluble dans l’acide (ASCu) pendant la lixiviation in-situ ; toutefois, la récupération réelle dans la zone 6, qui affiche l’histoire la plus ancienne en matière de lixiviation, était d’environ 42 %. La comparaison des données d’analyses de forage obtenues à partir de trous forés avant et après la lixiviation indiquait également une récupération approximative de 42 %. La différence entre la récupération prévue (52 %) et réelle (42 %) réside probablement dans plusieurs facteurs, notamment la difficulté à maintenir la saturation des fluides, les effets de canalisation et la précipitation du gypse. ¦ MOTS CLÉS d’un puits à l’autre, extraction par solvant et extraction électrolytique (SXEW), lixiviation in-situ, modélisation, oxydes de cuivre, porphyreINTRODUCTION in-situ copper leaching at the San Manuel mine, Arizona, USA (Figure 1), began in 1986. It was recognized that some of the copper oxide resource was not economically recoverable by conventional open-pit and heap leach methods using solvent extraction and electrowinning (SXEW) and a high stripping ratio would be required to access part of the resource. At the time, in-situ leaching was becoming popular in the uranium industry, but the approach was virtually unknown in the copper industry, especially at a large scale."

Jan 1, 2019

By A. M. L. Cushing, S. Kelebek

Presently, adsorption is one of the effective methods of removing toxic contaminants from waste waters. The contaminants from metal mining industrial operations include an effluent water containing various types of heavy metal species at concentrations beyond the maximum allowable limits, which are 0.5 ppm and 0.3 ppm for nickel and copper species, respectively. Adsorption behavior of copper ions pre-chelated with diethylenetriamine (DETA) and triethylenetetramine (TETA) onto natural bentonite and peat has been investigated. Both natural bentonite and peat was found to be capable of removing these copper-polyamine complexes from aqueous solutions relevant to process water effluents. However, the adsorption capacity of bentonite was significantly higher than that of peat. Two models were used to study the adsorption kinetics: a pseudo-first-order rate expression and a pseudo-second-order rate expression. For both adsorbents, the data conformed best to the pseudo-second-order rate expression. Representation of the experimental data through adsorption models was also investigated. Out of the four cases considered, namely, Langmuir, Freundlich, Temkin and Dubinin-Radushkevich isotherms, it was found that for both bentonite and peat, the copper polyamine adsorption data conformed best to the Dubinin-Radushkevich adsorption model. The Langmuir model also represents the bentonite-copper polyamine adsorption system reasonably well as the second best case, suggesting that the amount adsorbed on bentonite might be a monolayer with strong affinity.

Jan 1, 2015

By I. Farr, H. Wittens

"In 1989 and 1990 abnormally high levels of arsenic in ore from the Thompson Open Pit Mine threatened Manitoba Division's electro-nickel production. The paper will discuss our development of a flotation process to separate pentlandite and gersdorffite (the prime nickel and arsenic bearing minerals).The presentation will focus on the development of the process from conception, through lab and plant test work, to plant optimization and full scale production. The paper will conclude with the benefits and cost of the completed project.INTRODUCTIONRejection of arsenic from nickel sulphide ores was not a primary concern in the Manitoba Division until 1989. At that time increased production in the Thompson Open Pit mine, which contains high arsenic ore zones, resulted in excess amounts of arsenic in the Thompson Refinery affecting electro-nickel quality. This problem was resolved through extensive efforts by Mill personnel. The purpose of this paper is to familiarize the reader with- the Thompson Mill.- the mineralogy of the Thompson orebody.- the evolution of Ni/As separation in the Mill.- the metallurgical impacts of the separation on the Mill.- the importance of the separation to the Manitoba Division."

Jan 1, 1991

By J. L. Wilson

"Many modern concentrators with VSD driven SAG mills still rely on the control room operator to manually adjust the speed in reaction to increasing bearing pressure. All too often, the problem with this strategy is by the time the operator reacts with a sudden speed increase, the SAG Mill is likely already on its way to loading up. To assist the new operators, the SAG Mill at B2Gold’s Fekola Mine in Mali needed a robust control that could handle load changes and unmeasured disturbances with minimal operator intervention. With modern Distributed Control Systems (DCS) powerful enough to run advanced control, they often have Model Predictive Control (MPC) blocks built in or available as an “add-on” license, and thus MPC can be readily implemented within the modern concentrator with a relatively low added capital cost. This paper discusses an implementation of two single output MPC controllers to control the SAG Mill at Fekola. This was implemented using the existing signals and advanced control blocks available to the installed DCS.INTRODUCTION Many modern concentrators with VSD driven SAG mills still rely on the control room operator to manually adjust the speed in reaction to increasing bearing pressure. All too often, the problem with this strategy is that by the time the operator reacts with a sudden speed increase, the SAG Mill is likely already on its way to loading up. The next step the operator may take may be to cut back the feed rate, or production until the SAG is once again stable. With this sudden reaction comes an abrupt change in SAG rotational speed and power consumption that sends a surge of material down the circuit as the mill suddenly ejects more pulp. Furthermore, choosing a higher rotational speed can lead to higher than normal liner wear as the cataract overshoots the toe of the charge and impacts the liners. After start-up at B2Gold’s Fekola Gold Mine in 2017, the SAG mill was being controlled manually. The SAG rotational speed was adjusted manually by the operator in step changes depending on whether the SAG bearing pressure was increasing, decreasing or stable. During this time of manual control, the SAG fresh feed rate was also adjusted to a tonnage setpoint with a PID controller. Generally, the SAG fresh feed rate setpoint was kept at a target value, but then the feed rate was throttled back if the SAG mill or grinding circuit showed signs of overloading. The extra challenges were that the operators had limited experience and were concurrently learning how the plant operated. Also, they were also occupied with managing situations in the rest of the plant. Often their attention was drawn away from the SAG mill and during that time, the SAG Mill would load up before they could react."

Jan 1, 2019

By J. B. Edwards

"The case is presented for the use of simulators for the computer-based training (CBT) of mining plant operators and for introducing them to automatically controlled systems. As well as their use in the classroom, the role of simulators is examined for ""on-plant"" use in trouble-shooting, fault-finding and maintenance of automatic systems. Case studies are presented showing how specific simulators are becoming established or have potential in the areas of automated materials handling, machine testing, setup and guidance. The evolution of scientific simulations into simulators of widespread practical use is discussed and present-day limitations of computer speed and graphics are considered. Related areas of research for the Canadian Centre for Automation and Robotics in Mining (CCARM) are identified.IntroductionCCARM's Commitment to Simulator DevelopmentAs automation is progressively developed and exploited in mining operations, there arises an urgent need to educate and train staff responsible for its introduction and operation in our mines and for its maintenance. For this purpose , an essential ingredient of an automation program is the development of appropriate mining system simulators for use by a wide variety of personnel. The author has been fortunate to have been closely involved with the development of automatic control systems for a variety of mining machines and mining systems in the United Kingdom. A key ingredient of the research phase in each case has been the use of simulation techniques. As projects have moved toward their commissioning and exploitation phase, the simulations have evolved into simulators tailored for use by machine operators and maintenance personnel. Illustrative case studies are presented later. The researach of the newly constituted Canadian Centre for Automation and Robotics in Mining (CCARM) will likewise involve extensive simulation, and the development of simulators (from the scientific programs) for use at the mine by operators and technicians will be given high priority in the Centre's over-all work program."

Jan 1, 1990

By M. Kosugi, Y. Kon, M. Kawata, J. V. Satur, K. Mitsuhashi, C. Tokoro, K. Horiuchi, R. Kawarabuki, B. Calabia

"Liberation of copper minerals is important in ensuring high flotation efficiency in copper sulfide flotation. The high pressure grinding roll (HPGR), microwave (MW), and electric disintegration (ED) are known to feature enhanced liberation over conventional comminution machines such as jaw crushers and ball mills by producing internal stresses on minerals or mineral grain boundaries through high compressive forces, thermal expansion of minerals, and pulsed high voltage discharges, respectively. In this study, each of these methods was applied before ball mill grinding to investigate its effect on enhancing the liberation of copper minerals in a low grade and fine-grained copper ore. The copper minerals observed in the tested ore sample are bornite, chalcocite, and chalcopyrite, and their grain sizes range from 10 to over 100 µm. Calcite, quartz, and feldsparare confirmed as gangue minerals. The liberation of the copper minerals by the different methods was analyzed using the mineral liberation analyzer (MLA) and compared. The result showed that the HPGR crushing was the most effective for enhancing copper mineral liberation. HPGR bench-scale test was then conducted on the copper ore and flotation was applied on a HPGR-treated sample to confirm the improvement in the flotation performance by applying HPGR.INTRODUCTIONIn order to recover copper minerals by flotation, copper ore is usually ground by ball milling to liberate the copper minerals from gangue minerals. In the case that the fine size copper minerals are targeted, grinding of the copper ore to a finer size is necessary to increase the copper recovery. However, finer size grinding by ball mill increases energy consumption significantly, which might deteriorate the economies of the mineral processing operation. HPGR, MW, and ED have been recently the focus of researchers as new techniques for enhancing the mineral liberation in mineral processing (Tavares, 2004; Kingman, 1998; Wang, 2010).HPGR crushing is considered to generate micro cracks along mineral boundary when rocks pass between two rolls by applying high compressive force. In the MW treatment, micro cracks are reported to be generated at crystal boundaries by differential thermal expansion of crystals attached to each other. In the ED treatment, micro cracks are known to be produced by plasma current flowing along mineral grain boundaries. These treatments are expected to increase mineral liberation (Fujita, 2001),improve flotation performance(Michaelis, 2005), and reduce ball mill work index(Kaya, 2010)."

Jan 1, 2017

By C. Xiao, F. Mohamm, A. Borsoi

"Nitrogen compounds produced by cyanide destruction and/or blasting are often a cause of concern for environmental compliance and at times, for water re-use in metallurgical circuits. Natural attenuation in tailings ponds and wetlands is not always sufficient to ensure compliance and/or achievement of overall water management objectives. This paper provides a general overview of active treatment methods for nitrogen management followed by an investigation of selective adsorption combined with electro-oxidation as the potential treatment method for thiocyanate. Results from bench scale treatability study are presented. The concept of holistic assessment of nitrogen management at mine sites using Risk Adjusted Life Cycle Cost is introduced and discussed in the context of gold mining operations using sodium cyanide.INTRODUCTION Unlike metals, nitrogen compounds present in mine waters originate entirely from anthropogenic sources rather than mineral deposits. Table 1 summarizes the main sources of nitrogen compounds reporting to mine wastewater.The best management practice related to the use of ANFO involves minimizing contact between ANFO and water, control and monitoring of blasting to reduce the occurrence of misfires, and reducing the consumption of blasting reagents for a given ore body. The most common practice for the management of NaCN is the incorporation of cyanide destruction in the metallurgical flowsheet and the use of tailings impoundments and holding ponds for natural attenuation of cyanide destruction residues such as NH4-N and CNO. At most mine sites there is no active management of NO3-N and SCN in wastewater. While current practices have produced satisfactory results, new enhanced methods to manage nitrogen compounds at mines are needed due to: 1) Increased scrutiny over the adverse effects of nitrogen compounds released into the environment; 2) New effluent standards; and 3) The shift away from wet tailings towards dry stack systems resulting in diminished natural attenuation and dilution of nitrogen residues prior to effluent discharge or water re-use in mineral processing."

Jan 1, 2017