Search Documents

By X. X. Wu, Q. Zhang, R. H. Fan, Y. J. Feng, J. D. Liu, P. Z. Zhao

In the present study, AA6016 automotive sheets with different grain size were fabricated through changing fabricating parameters, and the effects of grain size on the bendability were studied by bending test and optical microscopy. The results showed that the sheet with coarse grains exhibited poor bendability, and some micro-cracks were revealed at the surface of the bending samples. While the sheet with fine grains exhibited good bendability, and the bending samples showed smooth surface. Shear bands on the cross section of bending samples were observed. It was found that samples with coarse grains had more shear bands. These shear bands distributed in bundles, which facilitated the formation of continuous neckings and micro-cracks. However samples with fine grains had less shear bands, which distributed uniformly. The decrease of grain size could not only hinder the formation of shear bands, but also improve the homogeneity of its distribution during bending. On the other hand, refining grains could increase the amount of grain boundaries, which impede the propagation of shear bands. Hence the decrease of grain size could hinder the formation of continuous neckings and micro-cracks during bending, resulting in the significant improvement of the bendability.

Jan 1, 2015

By M. Abdellatif

Successful demonstration of The Mintek Thermal Magnesium Process (MTMP) was achieved in November 2004 at the pilot-scale, About 30 tons of magnesium producing recipe was smelted in the DC arc furnace over a continuous operation of 8-days, Twenty-two furnace batching-tapping operations were carried out at a feed rate of 525kg/h and a smelting temperature of 1600-1700°C, The MgO content in the produced slag was as low as 6,7%, and averaged 9,2% MgO, resulting in an overall magnesium extraction of 77%, which reached 87% during good operating periods, Magnesium vapour was extracted at a rate of 70-85kg/h and was delivered to the condenser that was operated at 680-720°C, The magnesium was captured in the condenser crucible in a liquid state, allowing its prompt tapping, More than 3500kg of crude metal were produced over 15 on-line metal tapping operations, On average, a condensation efficiency of 85% was achieved during the entire testwork, which peaked at 87% during steady operations, The quality of the crude metal was similar to, if not better than, that of the Magnetherm's crude magnesium, A pre-feasibility study has indicated that the MTMP has the potential for lower capital and operating costs as compared to the electrolytic process, and therefore Mintek and its consortium partners are exploring opportunities for a commercial production facility.

Jan 1, 2006

By W. A. Jones

THE estimation of the average value of gold ore involves many considerations, among them the correct sampling of the deposit, the dilution by waste, and the loss of high-grade fines. It is a common experience that, after all these factors have been evaluated, adjustment of the assays is necessary before satisfactory agreement between the calculated mine grade and the mill heads is obtained. In fact, at many mines the latter correction overshadows all others in the preparation of routine estimates. For this reason it is proposed to deal only with the mathematical treatment of mine assays and the problem of bringing estimates into conformity with the corrected mill heads. Mine assays differ from physical measurements because the range of values is very great and these are not symmetrically distributed above and below the average, there being fewer high than low results. There is no widely accepted mathematical procedure for determining the average of series of measurements which exhibit these characteristics. Customary practice consists in empirically reducing high assays until a satisfactory agreement with mill heads is reached. It was thought that more confidence could be placed in grade estimates if a logical basis for calculations could be devised .. In an attempt to find a fundamentally sound procedure, amenable to practical application, many series of assays comprising over 235,000 channel samples (1) were studied at Hollinger Consolidated Gold Mines, Limited. Such an investigation could only be made where records covering many years of operation are available and where tabulating and calculating machines are in use. The results are recorded in the hope that the relationships noted for the large groups of assays used are of fundamental character and that the data will be useful to others dealing with the problem of grade estimation.

Jan 1, 1943

?Bank Lending to the Mining Sector affected by 2 broad factors since Mid 2008: 1. Economic Downturn (?the Real Economy?) for mining companies directly reflected in lower metal prices (current and forecasted). In the case of gold companies, minimal effect. 2. Financial Crisis (?the Credit Crunch?) as it has affected the lending activities of those banks active in the mining sector.

May 1, 2009

By M. Vaillé, B. Bossé, N. Durupt, A. Michaut

Imouraren is a sedimentary uranium deposit (> 150,000 tU @ 800 ppm), located approximately 100 km North-Northwest of Agadez (Niger); its depth reaches 110 to 170 meters. For low-grades ores, heap leaching is commonly considered as the appropriate technology for metal recovery. More precisely, the ore is crushed (≤ 300 mm) and agglomerated before being stacked. In this case, sulfuric acid can be added during agglomeration and/or irrigation (for three months to a year) to improve uranium recovery. It is known that mineralogical, chemical and physical properties of the uranium ore impact recovery, yet many challenges remain to increase recovery using this process. For example, ore heterogeneity and spatial variability (e.g., variation in uranium, carbonate and/or clay contents) can affect heap leaching performances (i.e., metal recovery, acid consumption or neutralization, percolation rate). However, laboratory column tests using composite ore sample that do not consider ore heterogeneity are widely used to anticipate recovery. Consequently, a new approach that consists in using Imouraren drill core ore samples was recently investigated. This latter also enabled a better assessment of the main parameters that influence uranium recovery and proposed a new predictive model to optimize mining operations.

Jan 1, 2020

By F. Rashchi, N. Naseri Joda

Recycling of electronic wastes is an important subject both from an environmental point of view and also the recovery of valuable materials. In this research, PC board scraps were leached to recover Cu, Ag, Au and Pd. Due to the high cost of the shredding process and to avoid secondary pollution from odors and dusts, board scraps were cut into 5X5 cm2 pieces. To determine the most effective leachant, aqua regia, nitric acid, hydrochloric acid, ammonium persulfate and potassium persulfate were tested. The effect of the leaching parameters, the leachant concentration, temperature, leaching time and liquid to solid ratio were studied and optimized using response surface methodology.

Jan 1, 2011

By N. Golchinfar

Tunnels in deep mines are subjected to high stresses. Fracture and failure of the rock mass around an opening can occur when mining-induced stresses are high. In burst-prone grounds, mining-induced seismicity can cause additional dynamic loading which can further increase the stress around the tunnels. When the dynamic stress reaches the rock mass strength, fracturing can occur and rockburst may happen (depending on loading stiffness around the failed rock mass). Rock support installed in the tunnel must be capable of dissipating dynamic energy and holding the failed rocks. Hence, it is important to estimate the depth of failure for rock support design. This paper focuses on how to model depth of failure under dynamic loading. In the modeling, two scenarios of rock failure are considered. In the first scenario, rock failure occurs under static loading and subsequent dynamic loading further increases the depth of failure. In the second scenario, no failure occurs under static loading but in the subsequent dynamic loading, failure around the tunnel is created.

Aug 1, 2013

By J. M. Réjean Gagnon

"Quebec Cartier Mining Company is currently mining a low-grade iron ore deposit in northeastern Quebec. The Company is producing some 8,000,000 dry gross tons of concentrates per year, grading about 66 per cent iron. The pit, which is located on the keel or hinge line of a fold, will eventually be about 1,000 feet deep with a surface area of 8,000 by 2,600 feet. The most significant structural discontinuities in the mine are the natural bedding planes and secondary perpendicular joints. The exposed walls are subjected to a sub-Arctic climate and heavy blasting occurs approximately six times a month.QCM utilizes design and operating techniques to control rock fall. Steps are also being taken to analyze the ultimate over-all pit slope stability."

Jan 1, 1968

By K. Ebrahimi-Nasrabadi

The dependence between the extent of conversion of cryptocrystalline magnesite to caustic magnesia was studied experimentally in the temperature range of 400?1200 °C and for calcination times up to 8 h. A TGA?DTA analysis showed that decomposition begins at temperatures as low as 340 °C and is completed at 600 °C. Measurements of specific surface area (SSA), iodine adsorption number (IN), crystallite size, and loss on ignition were carried out to characterize the product quality. It was found that while all the parameters are dependent on the extent of calcination, densification of the product caused by grain coarsening affects their final values. As a consequence, SSA and IN went through a maximum with time. The study showed that high quality caustic calcined magnesia can be produced in a narrow range of temperature (600?650 °C) and time (1?4 h). Medium quality caustic calcined magnesia can be made within a wider range of parameters.

Aug 1, 2013

By G. Bonnivard

"A complete laboratory process for the treatment of lateritic ores containing a high proportion of iron, as well as chrome and alumina, has been established. The ores treated originate from the tropical zones and result from superficial climatic alteration. According to recent estimates, the known reserves of such ores reach many billions of tons, thus representing huge potential reserves for the elements they contain.The process used is based on the alkaline roasting of pelletized ore in the presence of sodium carbonate. This treatment results in the separate recovery of pellets of upgraded iron ore, pure chrome oxide and hydrated alumina. The research described in the paper aims at determining the best experimental conditions for obtaining the highest extraction of the required oxide from this type of ore."

Jan 1, 1967

By D. B. Apel

As depths to the ore bodies keep increasing around the globe, the problem how to deal with the increasing temperature of undisturbed rock mass becomes very important. In extreme cases the rock temperature at the bottom of the mine could raise up to 80 °C. In deep mines, geothermal heat is considered as the primary heat load contributor, which accounts for 50?90% of the total heat load depending on different geological conditions. Thus the geothermal heat control in underground mines is the most important and demanding issue to ensure a suitable working environment. In this study, expanded perlite aggregate (EPA) was incorporated as a lightweight substitute for sand. Five mixtures were prepared using 0, 25, 50, 75 and 100% replacement ratios of sand by EPA. These, mixtures were tested in the laboratory for both the insulating and strength properties of the developed shotcrete. The goal of this research was not only to develop shotcrete which would exhibit good insulating properties but also which would exhibit strength properties similar to the regular shotcrete. This paper not only reports the results of the laboratory tests but also discusses the output of numerical model which was performed to evaluate the benefits of using the insulating shotcrete in reducing the cooling costs at hot underground mines.

Aug 1, 2013

By J. Fournier, D. Fortin, F. Robichaud

Since milling began in 1988, the Laronde mill has been expanded several times, the most recent, increasing the milling rate from 5 000 to 7 000 mtpd. Laronde uses SAG/ball mill grinding followed by copper and zinc flotation circuits. A cyanidation/Merrill-Crowe process recovers the remaining gold and silver in the flotation tails in order to cope with high silver/gold ratio associated with the discovery of the Penna shaft. Since the commissioning of the Merrill-Crowe refinery in 2000, several modification and expansion projects were performed to reduce health and safety hazards. Remarkably, several of these improvements have contributed at increasing productivity and Net Smelter Return of the refinery while reducing worker's injuries. In 2004, the refinery was audited to evaluate and quantify the circuit performance. Metallurgical and mechanical operating conditions of the refinery are now understood and areas for further improvements are well defined. This paper describes some of the factors that have contributed to this improvement and describes how ergonomics and recovery can further be improved.

Jan 1, 2005

By John H. Morris, R. Gwilym Roberts

"The Upper Beaver Mine, Kirkland Lake, Ontario, is a copper-gold deposit in mafic flows and sedimentary rocks. The deposit consists of a number of orebodies of two types: copper- and gold-bearing chalcopyrite-pyrite-magnetite ore; and gold-bearing quartz veins. Chalcopyrite-pyrite-magnetite ore occurs in two structural forms: as cherty interflow material in coarse clastic roks underlying flows; and as veins. Both sedimentary and vein ore occur in each orebody. The goldbearing quartz veins occur in interflow sedimentary units and at the contacts of oligoclase porphyry dykes.The deposit is in a localized, volcanic-sedimentary basin which began to develop during the emplacement of the upper units of the pyroclastic and sedimentary Gauthier Group, and continued to the early mafic flow activity of the overlying Kinojevis Group. The formation of the volcanic-sedimentary basin is ascribed to the D0 deformation. The deformation is significant in terms of the structural configuration in the mine area, and may be significant regionally, but this has not been demonstrated. The early deformation was followed by two tectonic deformations. D 1 is associated with a penetrative mineral foliation, axial planar to upright mesoscopic folds and striking parallel to the trend of regional fold structures. Mesoscopic flexural-slip folds, kink folds and fracture-crenulation cleavage are attributed to the D2 deformation. It is probable that no large-scale fold structures are associated with the D2 deformation. The gold-bearing quartz veins were folded during the D1 deformation.The close spatial relationship of copper-gold, chalcopyritepyrite- magnetite veins with chalcopyrite-pyrite-magnetite in cherty inter flow material is strong evidence for the derivation of the veins from the sedimentary ore by hydrothermal, metamorphogenic processes. By analogy, it is suggested that the gold-bearing quartz veins were formed by similar processes."

Jan 1, 1982

By Jean-Luc Collins

"This new tool can be used as a quick guide f or the assessment of the potential economic wealth of any risky capital project. It does provide an unambiguous recommendation of the type ""go or no go"" to the decision-maker simply by comparing two different ratios profit/investment. One ratio determines the minimum value required to at least break even while the other measures a probable value based on the asymptotic theory of statistical extremes.Its application is briefly illustrated by means of an underground gold mine extension project, an oil sands mine project and a polymetallic open pit project.Once a favourable recommendation has been obtained then a detailed ""cash flow after taxes"" analysis can be carried out for the project.IntroductionMany tools are used in financial decision-making such as the payback period, the discounted cash flow, the internal rate of return and the wealth growth rate (Berry , 1971).These tools are useful and meaningful in evaluating normal projects closely related to regular business where the number of assumptions made is usually very small and where the cost of capita! is usually selected as a discount rate or a hurdle value. In situations where a significant number of assumptions have to be made,two problems can emerge, namely:I. the risk involved is underestimated leading to a potential financial disaster; or2. a good opportunity is lost because the approach used in evaluating the project is too conservative.Each assumption has its own degree of uncertainty and it is well known that combining uncertainties together can lead to a total uncertainty of critical proportion. The easiest way to account for risk is to increase the discount rate or the hurdle value, but this approach alone is quite subjective and can easily lead to the problems described above."

Jan 1, 1993

By Maxime Tacher

BRP (Bombardier Recreational Products) designs and commercializes recreational vehicles such as watercrafts, sport boats, snowmobiles, ATVs... The Spyder roadster is the last product in the Can-Am product family lineup. To remain at the forefront of innovation, a hybrid motorization version of the Spyder is being developed in order to reduce fuel consumption and emission of greenhouse gases. But, the addition of electric components (e-motor, lithium-ion battery... ) raises the issue of added weight and volume. This article deals with the mass reduction of this Spyder by optimizing its frame.

Jan 1, 2011

By Jean Robitaille

La découverte du gisement du puits Penna a nécessité une révision complète de tous les circuits du concentrateur Laronde pour permettre, premièrement, l?adaptation du procédé à la nouvelle minéralogie et deuxièmement, l'accroissement du tonnage de 1800* à 4500 t/j. Aux circuits existants de broyage, de flottation du cuivre, de cyanuration et du charbon en pulpe, les circuits suivants furent greffés : broyage semi-autogène, flottation du zinc, manutention des concentrés (épaississage, filtration, entreposage et chargement automatisé), décantation à contrecourant et précipitation au zinc, destruction des cyanures et remblai en pâte. Cet article se veut une revue des différentes étapes du projet d'agrandissement du concentrateur qui se sont effectuées par phases progressives de 1997 à 2000. De plus, une description des nouvelles technologies sélectionnées et implantées est présentée.

May 1, 2001

By L. C. S. Dharmasiri, S. M. Shin, A. Senaputra, J. S. Sohn, K. H. Park, J. Avraamides

Reducing agents can be applied to leach metal values from natural and secondary resources such as laterite ores and deep sea manganese nodules and recycled materials such as spent batteries / catalysts which contain high-valent metal oxides of manganese, cobalt and iron. Selective leaching of some metals can be achieved by selecting conditions to control the saturated solubility and dissolution rates of metals from oxides or mixed metal/oxide matrices. The leaching results are rationalized on the basis of chemical species, Eh-pH diagrams and heterogeneous kinetic models. The role of reducing agents such as hydrogen peroxide, sulfur dioxide and iron(II) sulphate, in acid, alkali and in the presence of complexing ligands such as ammonia for the improvement of the leaching of metal oxides and metals is discussed. Previous studies on acid leaching of metals from nickel laterites, manganese nodules and spent catalysts/batteries in the absence or presence of reducing agents show that the rate controlling step involves the diffusion of protons through a thickening product layer on the particle being leached. It is shown that the leaching of nickel and cobalt from manganese nodules and zinc-carbon batteries in ammoniacal sulphur dioxide solutions also obey shrinking core kinetics.

Jan 1, 2014

By David J. Morrison

Scarcity of truck tyres, increasing cost and decreasing availability of labour, increases in fuel costs and project budget blowouts have changed the paradigm behind mining equipment selections. The cycle of commodity changes have occurred in parallel with the increasing maturity of continuous mining machinery, mobile in-pit crushing systems and very large scale conveyor belt systems. This paper will consider the merits of operating continuous materials handling systems, mobile in pit crushing systems, relocatable crushing systems, relocatable conveyor systems and automated waste handling systems in place of the more conventional approach of truck haulage.

May 1, 2007

The Silvermines area of north County Tipperary in Ireland has experienced mining activity for over a thousand years, with lead, zinc, copper, barite and sulphur being extracted from a series of Carboniferous limestones. The last mine to operate in the area was closed in 1993. A legacy of contamination and derelict surface structures remain. Following the death of cattle in the vicinity in 1999, a governmental Inter-Agency Group was established to conduct an investigation. The ?Silvermines Rehabilitation Project? resulted, and included a proposal for the development of a Mine Waste Management Facility (MWMF) to act as a repository for waste materials from problematic sites across the area. The nature of the setting supported an effective solution from both a cost and performance perspective; and with limited maintenance requirements. Locating the MWMF where most wastes were identified would help minimise handling and relocation of materials. This position coincided with an area of artesian groundwater pressures. The resulting MWMF design consisted of a perimeter engineered embankment with the crest elevation designed to just exceed the groundwater piezometric surface. The base would remain unlined and groundwater permitted to rise up into and saturate the contained in-situ tailings deposits and imported mine wastes. The proposed system thus benefited from the ?wet cover? approach to minimising further oxidation of wastes and metal leaching, but without the usual accompanying outward hydraulic gradient and leachate management issues. A sub cap drainage layer with downstream outlet was incorporated to prevent any possibility of hydraulic rupture following an unexpected rise in groundwater heads. Leakage rates from the MWMF were deemed to essentially be driven by surface infiltration rates alone (characteristic of a ?dry cover? approach), with the proposed composite capping system simulated to perform at an infiltration rate of less than 1 mm per year. A toe drain was incorporated with the perimeter containment system, and this collection together with diverted neighbouring drainage was directed under gravity to a dedicated Passive Treatment System (PTS). Overall, effluent water quality from the PTS has been predicted to reflect an annual mass metals removal in the order of 95% below baseline.

Aug 1, 2013

By Steve Custer, Chris Bennett, Patrick Garretson, Glenn Dobby, Jacques McMullen

"Barrick Gold is in the process of expanding one of its grinding circuits at the Goldstrike property as a response to both increasing ore hardness and increased ore sensitivity to finer grinding as it relates to gold recovery. The plant currently operates with two parallel grinding lines, each with a SAG mill, a pebble crusher, and a ball milling arrangement. As part of determining what additional equipment was to be required, a CEET evaluation program was conducted (CEET is an acronym for Comminution Economic Evaluation Tool). The work included: Development of a hardness ‘model’ for the ore body, as described by SAG Power Index and Bond Work Index;Site benchmarking surveys to fine tune the SAG and ball mill calibrations within CEET;Conducting CEET studies to examine the process options;Comparing CEET results to standard grinding circuit design techniques.The recommendation of the study, presently being implemented, is the installation of an additional ball mill on one of the two grinding lines. This paper reviews the sizing techniques applied, providing a CEET case study for circuit performance analysis and circuit design. OVERVIEW OF COMMINUTION AT GOLDSTRIKEOre feeding the autoclaves at Goldstrike are first processed through two parallel grinding lines. Both lines use SAG mills with cone crushing of pebbles followed by ball milling. A summary of the key circuit parameters is provided in Table 1. Line 1 primarily processes underground Meikle ore, although when no Meikle ore is available, it processes open pit Betze ore. Line 2 processes Betze ore exclusively. The Mill Line 1 P80 objective for Meikle ore is 74 microns. According to the recovery optimization analysis, a P80 of 90 microns was recommended for Betze ore. The potential however exists to perform co-mingling of both ore types and feed the higher grade Betze ore to Line 1, in which case the P80 of 74 microns would be retained."

Jan 1, 2001