Search Documents

By R. Blosser

Phelps Dodge introduced a process improvement model known as Quest for Zero in 2001. In 2004, the focus of Quest for Zero shifted from corporate-led initiatives to projects led by site personnel. The Hydrometallurgical Division at Morenci focused on two (2) significant process improvements: reducing electrolyte bleed and organic losses. In September 2004, Morenci kicked off a bleed reduction project to reduce electrolyte bleed by 45%. By the end 2005, electrolyte bleed was reduced by 55% through understanding and reduction of variance. Significant process changes made during this time period include changes in acid-addition strategy, reduction of uncontrolled bleed, and optimization of bleed placement. In April 2005, the organic reduction project began with the goal of reducing losses by 15%. Operational improvements during this project included improved organic recovery systems, mixer speed optimization, and picket fence installation. By the end 2005, this project reduced organic losses by 35% and current losses are 48% lower than at the start of the project. These projects and smaller Questfor Zero projects have resulted in sustainable annualized savings of $13 million in Morenci hydrometallurgical operations. Through the use of Six Sigma tools, process variances can be controlled and reduced.

Jan 1, 2007

By J. Basi, D. F. Rucker

"A review of historic operating practices of the heap leach pads at the Los Filos Mine, Mexico, revealed periods of restricted cyanide addition, reduced leach time, and insufficient irrigation flow. These issues all led to the buildup of partially leached recoverable gold inventory within the leach pads. Drawing down this inventory represented an opportunity to bring value forward. This paper outlines the strategic initiatives which were implemented as efforts to accelerate the inventory drawdown, including geophysical mapping and pressure injection.INTRODUCTION Los Filos is a heap-leach operation located in the Guerrero gold belt in southern Mexico. Operational and hydraulic challenges at the Los Filos Mine have led to a buildup of gold in inventory within the leach pads. Operationally, periods of restricted reagent addition, reduced leach time, and insufficient irrigation flow have compounded over the last eight years, and resulted in significant inventory growth. Hydraulically, the leach pad has issues with low permeability and solution channeling due to the fines and clay content of the ore. The leach pad is storing high-grade pregnant leach solution (PLS) as perched aquifers above areas that are compacted and difficult to drain. These operational and hydraulic challenges made it particularly difficult to spatially predict the precise locations of the inventory build-up. Fortunately, the challenges at Los Filos are not unique to the mine, and others have taken steps elsewhere to reduce metal inventory through a program that targets areas for inventory drawdown. For example, Ghorbani et al. (2016) noted that a method of injecting barren reagent solutions, applied directly to specific areas of a leach pad to reduce inventory, was presented by Wan and Brierley (1997) and Wan (1997). Seal (2004; 2007), Seal and Jung (2005), and Seal et al. (2012) have put the injection methodology into practice in Nevada and Colorado gold mines with a technology called Hydro-Jex®. The goal of Hydro-Jex has been to supply reagents at a high pressure over a short duration, followed by periodical low pressure rinse periods to remove leached metal and resupply fresh reagent to the ore."

Jan 1, 2017

By R. A. Crouse

The Tanco pegmatite at Bernie Lake, in the Lac du Bonnet mining district of southeastern Manitoba, is a unique deposit of Li, Rb, Cs and Ta, with substantial reserves of Be and several industrial minerals. This paper summarizes the present state of understanding the regional geology, structural setting, zoning, mineralogy and geochemistry of the pegmatite, and the mining and ore-processing methods used in its exploitation.

Jan 1, 1979

By L. A. Mells

"A laboratory test program was initiated by the Department of Energy, Mines and Resources as part of the National Uranium Tailings Program to investigate the applicability of a radium selective ion exchange complexer for removing radium from Canadian uranium mining effluents. The test program was carried out by Melis Consulting Engineers Ltd. under contract to the Department of Supply and Services using the Saskatchewan Research Council facilities located in Saskatoon, Saskatchewan.The results of this work showed the ion exchange complexer, Dowex XFS 43230.00, to be efficient in removing radium from contaminated water of uranium mining operations with the ultimate loading capacity of the resin on one type of water treated being determined as approximately 1,600 Bq/cm3 of new resin. Although this resin has potential application for treatment of effluent streams in uranium operations it has been identified that the resin efficiency and capacity is directly related to the chemistry of the water being treated and site-specific testwork is required in order to establish reliable design data for full-scale operations.IntroductionThe possible applicability of a radium-selective ion exchange complexer for removing radium from Canadian uranium mining effluents had been identified and discussed as a possible alternative to present radium removal methods during a review of disposal technology options for the National Uranium Tailings Program of the Department of Energy, Mines and Resources(1). Work by other workers(2.3) had shown the complexer to be very efficient in removing radium from contaminated water. Also, plant trials on contaminated minewater at the Mt. Taylor uranium mine in New Mexico is reported to have shown the resin complexer to be efficient under plant operating conditions.As a result, a laboratory test program was initiated by the Department of Energy, Mines and Resources as part of the National Uranium Tailings Program to investigate the suitability of this resin for Canadian uranium mining effluents. The test program was carried out by Melis Consulting Engineers Ltd. (MCEL) under contract to the Department of Supply and Services using the Saskatchewan Research Council (SRC) facilities located in Saskatoon, Saskatchewan."

Jan 1, 1985

By J. Fujioka, Y. F. Gu, C. Cui, D. Ping, A. Sato, H. Harada

"A new kind of cast & wrought (C&W) Ni-Co base superalloys named as ""TMW alloys"" are developed recently for compressor or turbine disks of gas turbine engines in High Temperature Materials 21 Project at National Institute for Materials Science (NIMS) in Japan. These Ni-Co base superalloys combine the characters of two kinds of y- y' two-phase alloys (Ni-base and Co-18at%Ti alloys) and have higher tensile strength and creep resistance than C&W UNDIMET 720Li superalloy."

Jan 1, 2006

By A. Burkert, A. E. Hajj

"An information system has been developed for the use of companies considering developing a new mine which may be liable to secondary sulphide ignitions or by existing operations. The system uses the Comdale X expert system to analyze information about a particular mine. The system will indicate whether the mine is likely to experience ignitions and what precautions can be taken to reduce or prevent their occurrence. The advantage of an information system using expert system and artificial intelligence principles is that it can recommend action when there is an incomplete knowledge of all the system parameters. By interrogation of the user it can determine the state of knowledge and react accordingly. It is considered that such systems could be of significant use in mine planning for new and existing properties, especially where operators have limited expertise regarding secondary sulphide ignitions. IntroductionSulphide ignitions occur in the underground mines of several countries, including Australia, Canada, Finland, South Africa and the United States of America (1·3) and there has been a significant increase in their number and severity over the last decade(2.4). The basic causes of such ignitions are not well understood and man incidents are not reported or documented.Sulphide ignitions can pose a serious threat to the health and safety of mine workers and to the cost and efficiency of the mining operation (1-5). Byberg(6) described the three major problems associated with sulphide ignitions as:1. the force of the initial explosion can endanger workers and equipment;2. the intense heat of the ignition's flame front can endanger workers and equipment and may also ignite combustible material resulting in mine fires; and3. the sulphur dioxide produced by the ignition may be of such quantity and concentration to endanger workers, as was tragically demonstrated at Geco. In this incident in October 1985, a worker was killed at a position 2400 metres from the ignition point of a sulphide ignition at Manitouwadge, Ontario."

Jan 1, 1994

By V. Gangrade

Recirculation is the major concern associated with the utilization of booster fans. In controlled recirculation, a portion of the return air is purposely mixed with the intake air and the mixture is directed towards a working district, while the air quantity and gas concentrations in the air are closely monitored and managed. The objectives of this study were to determine the gas concentration in intake and return airways during controlled recirculation, and to determine the recirculation fraction for multiple headings. Experiments were conducted in a laboratory model to determine the effect of controlled recirculation on the quality of air circulated through the working faces. Preliminary results showed that recirculation is beneficial to ventilation planning because it reduces the build-up of air contaminants at the working faces and reduces the overall power consumptions. The experimental results were used to quantify the recirculation fraction and to calibrate ventilation models of the laboratory model. These models are used to simulate the controlled recirculation and to predict the gas concentrations in multiple headings.

Aug 1, 2013

By R. Carpenter, H. Muntanion, P. Kleespies, E. Flood, M. Tansey

Abstract - BHP Minerals discovered the Archean lode gold ULU deposit on the western margin of the High Lake Volcanic Belt in 1989. The greenschist to amphibolite facies mafic volcanic and sedimentary rocks on the property are folded into a 5 km-long anticline. There is a close spatial association of Au-As zones to the trace of this F2 ULU anticline. The largest of these auriferous zones, the Flood zone, is localized at the core of the fold. The southeast-trending Flood zone consists of several anastomosing lenses that have been traced for 435 m on surface. Overall, it dips steeply (70° to 80°) to the southwest and has been intersected to depths below 600 m. The hosting high-iron tholeitic basalt displays a lower amphibolite mineral assemblage of ferrohornblende + plagioclase + ilmenite with accessory quartz and epidote. Alteration minerals include biotite, chlorite, hornblende, actinolite-tremolite, and potassium feldspar (microcline) with minor calcite, epidote, tourmaline, and titanite. The highest gold values occur where brecciated basaltic wall-rock clasts are replaced by acicular arsenopyrite + quartz + K-feldspar. BHP Minerals completed 54,783 m of both exploration and resource development drilling before selling the ULU property to Echo Bay Mines in 1995. Development of ULU as a satellite deposit to Echo Bay’s Lupin mine began in 1996. A -15% ramp was extended to the 155-meter level, and 16,011 m of underground drilling were completed before the decline in gold prices forced a suspension of activities at ULU in August 1997. The current owners, Wolfden Resources Inc., drilled 18,569 m in 2004 to increase confidence in the resource blocks. Following this drill program, a revised resource calculated by an independent consultant determined that the ULU deposit contains an inferred/indicated mineral resource of 1,130,000 t grading 11.34 g/t gold (373,748 oz) to the 360-m level. The portal was re-opened in 2005 and a prefeasibility study is underway.

Jan 1, 2004

By Daniel Lachapelle, Nuri Hmidi, Turgut Yalcin

"Simulation can serve as a convenient tool in studying the behaviour and performance of grinding circuits by facilitating the evaluation of various scenarios and identification of optimum operating conditions. This technique was applied to the St Andrew Goldfields Ltd.’s Stock Mine Mill which is a 1300 tpd gold milling facility, offering custom milling services as well as processing the Company’s own ores. Lack of adequate instrumentation in the mill poses a challenge in attaining optimum performance especially with changing ore types and characteristics. The grinding process is monitored essentially by manual measurement and adjustment of pulp densities at various streams. A simulation program was designed to assist in the effective implementation of this mode of grinding control. Product sizes from both the primary and secondary grinding circuits were correlated empirically to relevant process variables using a database formed from the results of past sampling campaigns. The simulator was created in Microsoft Excel whose data analysis and optimization tools coupled with its Visual Basic Programming capabilities were found to provide an excellent environment for the development of a cost-effective, efficient and user-friendly simulation program.INTRODUCTIONGrinding is often a very costly unit process in milling operations, mainly due to the excessive energy consumption associated with it. For example, for a Canadian copper-zinc flotation mill, grinding was listed as being the most costly item taking up 30.4% of the total milling expenses, followed by the flotation cost at 2 1 .O% (Kidd Creek Mines Ltd., 1982). A survey on 45 copper flotation mills around the world showed the average grinding cost to be 34.5% of the total milling cost (Weiss, 1985).Overgrinding aggravates the cost issue, while insufficient grinding either causes loss of valuable minerals to tails or results in low-grade concentrates. Therefore, it is essential that grinding circuits be carefully controlled and monitored. To this end, a great deal of effort has been devoted over the years to the modelling and simulation of grinding systems in order to assist in the efficient running of these processes."

Jan 1, 2001

By A. Luszczkiewicz

This paper presents the beneficial effects of non-oxidative leaching of final and intermediate copper sulfide concentrates with sulfuric acid prior to the final cleaning stage of flotation. This unique process, combining leaching and flotation, appears to be advantageous for difficult-to-treat carbonate-bearing Polish copper ores, such as those processed in copper concentrators at KGHM Polish Copper. It was shown that after the chemical decomposition of about 70 % of the total carbonates naturally present in the flotation feed, a considerable enhancement of subsequent flotation results (both grade and recovery). The resulting products of non-oxidative leaching are solid hydrated calcium sulfate (gypsum), soluble magnesium sulfate and gaseous carbon dioxide. The beneficial effect established by the laboratory leaching tests was subsequently confirmed during a pilot plant operation treating final copper concentrate and a problematic intermediate concentrate at the Lubin concentrator.

Jan 1, 2007

By M. A. Perras, M. S. Diederichs

"The Niagara Tunnel Project (NTP) is a 10.1 km long water-diversion tunnel in Niagara Falls, Ontario, which was excavated by a 14.4 m diameter tunnel boring machine. The excavated rock types included limestone, sandstone, siltstone, shale and mudstone. Based on observations and measurements the overbreak was divided into four zones. Approximately half the tunnel length was excavated through the Queenston Formation, which locally is a shale to mudstone. Three of the four overbreak zones were within the Queenston. Zone 1 includes the formations above the Queenston Formation, Zones 2 and 4 are border regimes with little or no influence from St. Davids Buried Gorge and Zone 3 is the area influenced by the gorge. Zones 2 through 4 can be generally summarized as having overbreak as the result of stress induced spalling. Zone 2 marks the transition from slabbing at the Whirlpool contact in the stress shadow to spalling towards Zone 3. The behaviour of Zone 3 is interrupted from the typical high stress behaviour due to the presence of St. Davids Buried Gorge. As the tunnel passed from the gorge the high regional stresses induce spalling, which creates the typical notch shaped overbreak geometry of Zone 4.Three modelling approaches were used to back analyze the brittle failure process at the NTP: damage initiation and spalling limit, laminated anisotropy modelling, and ubiquitous joint approaches. Analyses were conducted for three tunnel chainages: 3+000, 3+250, and 3+500 m because the overbreak depth increased from 2 to 4 m. All approaches produced similar overbreak geometries to those measured. The laminated anisotropy modelling approach was able to produce overbreak depths and chord closures closest to those measured, using a joint normal to shear stiffness ratio between 1 and 2. The back analysis results were able to produce sets of stress and strength inputs for different sections of the tunnel at the transition from overbreak Zone 3 to 4. The back analysis procedure demonstrates the importance of including the anisotropic stiffness in the numerical modelling approach to correctly capture the overbreak geometry and deformations around underground excavations."

Jan 1, 2015

"In response to mine head grades declining and orebodies becoming more complex, Glencore Technology has developed an alternative method for recovering economic minerals once leached into solution, rather than relying on conventional flowsheet options. The method involves the precipitation and separation of base metals from solution with limestone or lime. The final grade of these precipitate is not usually high enough to attract favourable terms of sale due to dilution from gypsum and sulphate salts. A set of operating conditions have been developed to allow the separation of the base metal precipitate from gypsum by exploiting the difference in particle size. A high-grade oxide product can be easily separated from the gypsum stream at very low cost. This process was originally developed by Glencore for zinc and copper systems. This paper reports on the successful application to nickel and cobalt, and this process has significant advantages over the incumbent precipitation process utilising magnesia.INTRODUCTION During evaluation of transitional and oxide zinc ore deposits during the 1990’s, Noranda Inc. (now Glencore) developed a sulphate based ore leach process to extract zinc into solution. For flowsheet development, conventional schemes dictated that once the zinc was dissolved in an acidified solution it was recovered by means of purification or solvent extraction followed by electrowinning and casting to produce zinc ingots. The deposits Noranda evaluated were high grade but had a relatively short mine life (10 years) and economic analysis showed that the projects couldn’t sustain the investment of a full zinc refinery. Compounding this problem was the lack of power supply infrastructure and the high power cost in the region. Noranda then evaluated alternative means of recovering zinc from solution. Laboratory testwork showed that a high-grade zinc precipitate (+50 wt% Zn) could be produced as an oxide, carbonate or sulphide by contacting acidified zinc sulphate solution with a number of reagents including soda ash, sodium hydroxide, and sodium hydrogen sulphide. Economic evaluation showed that the cost of the reagents are prohibitive, especially when the final product is still a metal intermediate (ZnO, ZnCO3 or ZnS). Noranda then continued to focus on fine zinc oxide precipitation for supply into the automotive tyre industry as this product would attract favourable terms of sale as a premium on Special High Grade (SHG) zinc."

Jan 1, 2017

By S. H. Ash

No single factor in modern civilization has played a more important part in the lives of our people than mechanization in industry and to it civilization owes much of its progress. In no industry has mechanization met more opposition than in coal mining, where ?the introduction of mechanical equipment has been opposed on many fronts for economic and social reasons. The term 'mechanization? as used in this report refers to the application of machinery to cutting, loading, and transporting coal from the face to the mine cars. During 1933, 84.7 per cent of the underground production of the bitu-minous-coal mines of the United States (1) was cut by machines, while in Washington only 17.6 per cent was machine-cut. Information in this report has been obtained from personal observations and from operating officials in the Roslyn-Cle Elum coal fields, especially D. R. Swem, manager of coal operations, and Thomas Murphy, superintendent, of the Northwestern Improvement Company, to whom the author is indebted for assistance. INTRODUCTION Although Washington coal-mining problems relating co mining methods, ventilation, drainage, and preparation of coal have been discussed in many publications, little has been published on mechanization in this region, principally because it has not been accepted generally that mining machines, mechanical loaders, and conveyors are necessary or economically adaptable to the variable and steeply inclined coal beds of Washington. Production of coal in Washington reached its maximum in 1918, when 4,128,424 short tons were produced; from that year, the trend was downward until 1934, when production was 1,383,103 short tons, the lowest since 1898; for the past two years, production has risen steadily.

Jan 1, 1937

By Wataru Inagaki, Kozo Kawano, Tetsuya Ando

Cu–Ni–P alloys are the typical precipitation-hardening material. Thus, Cu–Ni–P alloys is expected to apply alternative materials for heat-exchanger tubes. Therefore, it was investigated that the effect of the heat-treatment simulated brazing on mechanical properties of Cu–Ni–P alloy in this study. The hardness of specimen as heat-treatment simulated brazing after solution heat treated (sht) was shown approximately 105 HV. The peak hardness and tensile strength of the specimen as performed aged at 498 K for 43.2 ks following the heat-treatment simulated brazing achieved at approximately 140 HV and 260 MPa, respectively. From these results, it is expected the application to higher-strength tube for heat-exchanger after brazing in a furnace. INTRODUCTION Copper prices have increased dramatically with high in recent years. At the same time, manufacturing industries are required to reduce the environment load by reducing the wall thickness of the copper tubes used in heat exchangers. High-strength copper alloys are developed for reducing the wall thickness, while achieving high strength, of the copper tubes. Moreover, excellent workability and corrosive durability are also required by these copper tubes. Furthermore, the brazing, which are carried out at about 1050 K during the assembly process of heat exchangers, leads to grain growth and re-solving of additive elements. Nomura et al. achieved a tensile strength and Vickers hardness of approximately 260 MPa and 110 HV, respectively, after aging at 723 K for approximately 36 ks. Tamagawa et al. studied that the strength of Cu–Ni–P alloy rapidly increased at about 125 HV during the cooling process after the heat brazing due to the Ni2P precipitates sized 5–10 nm. Furthermore, Inagaki et al. achieved a Vickers hardness of approximately 130 HV by aging at 498 K for 10.8 ks. In the present study, we focused on the lowest aging temperature of 498 K in the previous study, and investigating the effect of heat-treatment simulated brazing on the mechanical properties of the Cu–0.93 mass%Ni–0.24 mass%P alloy.

Jan 1, 2019

By Abhinav Karanam, Lukas Bichler

Yttria Stabilized Zirconia (YSZ) is a promising thermal insulator for high temperature environments due to its thermal stability and chemical inertness. As was demonstrated with other technical ceramics (e.g., Alumina), addition of Single-Wall Carbon Nanotubes (CNTs) to a ceramic matrix may significantly enhance the mechanical properties of the composite ceramic. In this work, 8 mol% YSZ with 0.2, 0.5 and 1wt% CNTs composites were prepared via Spark Plasma Sintering process. The densification, Vicker’s microhardness, specific gravity and microstructure evolution of the composites were investigated. The results suggest that the addition of up to 1wt% CNTs to YSZ yielded optimal combination of the studied properties. At higher addition levels, the specific gravity decreased and clustering of CNTs occurred, leading to poor densification and a relative loss of performance.

Jan 1, 2014

By M. Zavvari

Flotation, as with most engineering disciplines, involves testwork. Commonly this means going from lab scale to pilot scale to industrial scale. It is important to conduct tests to identify key parameters and to optimize even at the lab scale. To reduce the number of tests while maximizing the information, it is necessary to use Design of Experiment and Statistical Analysis. In this communication Fractional Factorial Design was used to identify the effect of 7 main factors on barite flotation recovery from jig gravity tailings at the Dorrin Kashan operation. The factors include: pH, collector and depressant dosage, impeller speed (RPM), pulp dilution, particle size and flotation time. By analysis of the output with Minitab software all factors were shown to have an effect. Among the factors, pH and flotation time have an interaction effect but the others have wise effect as an interaction effect and main effect. Finally, reliability tests at pH= 9, RPM= 1000, collector 1 000g/ton, depressant l 750g/ton, particle size 90 µm, flotation time 90 s, pulp dilution 23 % solids, the optimum level of each factor, were done. At the optimum level a barite concentrate with average specific gravity 4.308 g/cm3, average grade 93.72% and average recovery 90.04% was produced from the jig tail.

Jan 1, 2009

By D. G. F. Hedley, F. Grant

"In 1958, the Ontario Department of Mines appointed a committee to study the accident situation and mining methods used in the uranium mines in the E1liot Lake district. This committee reviewed the existing knowledge on mine design, pillar support and roof spans and came to the conclusion that scientific knowledge had not yet reached the stage of producing rational design procedures which would reduce the dependence on trial-and-error methods. Since that time, the Mining Research Centre has made numerous stress measurements in two mines to define the pre-mining and pillar stresses. A comprehensive series of tests has been done in the laboratory to measure the compressive strength of the rock; a geological survey of the region has been made to evaluate tectonic stresses; and a survey was done on mining conditions with regard to stable and unstable pillar configurations. This information has been used to evaluate pillar design as effected by pillar width and height, depth below surface, extraction and pre-mining stress fields. The resultant design of pillar widths and corresponding extraction as the depth increased is in line with past and present experience in these mines. The information available on roof stability is still insufficient to design stable stope spans with the same degree of confidence; experience and trial-and-error methods are still required."

Jan 1, 1972

By L. Shasko

Deliberative mapping is a method of public engagement designed to bring citizens and specialists together to inform policy decisions in conflict-laden areas of science and technology (Stirling and Davies 2004a). Citizens and specialists participate in the process both separately and together. A deliberative mapping study was held in Regina, Saskatchewan in October and November of 2019. Participants in the study assessed options for reducing greenhouse gas emissions in small, remote or off-grid communities, including assessing the role of small modular nuclear reactors (SMRs) in climate change mitigation. Deliberative mapping is designed to facilitate direct, two-way conversations between citizens and specialists through both formal and informal discussions. The relationship building component of this process may increase trust. Public consultation processes that lack two-way dialogue or are seen as obligatory rather than meaningful can worsen public opposition or lead to negative public perceptions. Public education alone is not enough to change public opinion. Providing people with more information on topics they already hold opinions on can work to reaffirm previously held biases, but building relationships can provide new pathways to overcome divisions and turn close-mindedness into open-mindedness.

Jan 1, 2020

By Jack Young

U. S. Steel Canada Inc.’s Lake Erie Works is the last green field integrated plant to be built in North America. The plant was designed using the best available environmental technology to develop an environmentally friendly production facility. A summary of the technology and measures used in the construction of the plant are summarized in this paper.

Jan 1, 2015

By Q. Li, X. -L. Lei

Accompanying global energy shortage and high energy prices, shale gas has been the focus of exploration and it has attracted great attention from both academia and industry. The combination of horizontal drilling and hydraulic fracturing enables the extraction of huge quantities of shale gas from impermeable shale formations. During the process of hydraulic fracturing, great amounts of water, sand and chemicals must be injected into the shale formation at a high pressure, which may trigger seismicity. Such events could occur due to the presence of faults or the reactivation of these potential faults. Shale is the main component of source rock in the Sichuan Basin, China, and has the greatest contribution to the natural gas of the basin. In order to investigate the fracturing mechanism of shale in the Sichuan Basin, China, a series of rock fracture tests under triaxial compression were carried out in the laboratory in order to investigate the hydraulic fracturing behavior in relation to the seismicity. Based on the high multichannel waveform recording system, the detailed spatio-temporal distribution of acoustic emission due to micro-cracking was used to examine the deformation and fracture behavior of shale. In addition, the effects of confining pressure on the deformation and fracture in shale under triaxial compression by acoustic emission monitoring and X-ray computed tomography were discussed in the paper. The experimental results indicate that the shale samples demonstrate brittle fracture behavior. The confining pressure has a great effect on the complexity of the fracture planes and the spatial distribution of acoustic emissions, but few contributions to the location of the major hydraulic fracturing plane. The foliation of shale plays a dominant role in the rupture process and the geometry of the major hydraulic fracturing plane. The high confining pressure increases the strength and restrains the deformation of shale during compression process. These results shed some light on the understanding of onset of hydraulic fracture initiation not only for shale gas exploration and production, but also for CO2 geological storage and underground energy storage.

Jan 1, 2015