Search Documents

By Rita Aiello, Stan Mack, Peter Werth, Joseph McCarney, Jozef Stachulak

"Johnson Matthey has developed the first diesel particulate filter (DPF) for underground mining that controls particulate matter (PM) at the same time as maintaining emissions of NO2 at or below engine baseline levels. DPF technology is critical for controlling PM which is classified as a carcinogen, but passively regenerating systems rely on the use of oxidation catalysts that can potentially increase NO2 emissions. This paper reviews the development of low-NO2 PM control technology and the results from testing this technology underground on diesel mining equipment. KEYWORDS Decomposition catalyst, Diesel particulate filter (DPF), Diesel particulate matter, Mining Continuously Regenerating Trap (CRT®), NO2, SCR INTRODUCTION The introduction of diesel particulate filter (DPF) technology on heavy duty diesel (HDD) engines has been an important step towards addressing the clean air and health concerns for mining companies. Control of diesel particulate matter (PM) emitted from diesel engines is already being implemented for on- and off-road vehicles, and similar legislation is being prepared for mining equipment. In addition to PM, the diesel emission control strategies (DECS) also reduce carbon monoxide (CO) and hydrocarbons (HC). Some DECS control oxides of nitrogen, or NOx, which is composed of NO and NO2. Johnson Matthey has led the development of emission control technologies for diesel engines for almost 30 years. Over the last ten years alone JM has supplied over 3 million Continuously Regenerating Trap (CRT®) DPF systems for on-road vehicles, and over 200,000 systems for off-road vehicles. The patented CRT technology combines a diesel oxidation catalyst (DOC) with a DPF to effectively trap harmful PM from diesel exhaust, while removing CO and HC. The DOC converts part of the engine NOx to NO2, which reacts with the trapped soot to regenerate the filter. As engines become more fuel efficient, less waste heat enters the exhaust. This can be a disadvantage for after-treatment systems as it leads to lower catalyst operating temperatures. The CRT system regenerates passively, without addition of heat, at temperatures that are typical of diesel engine exhaust. JM recently launched the Mining CRT system which integrates CRT technology with NO2 abatement to reduce PM and tailpipe NO2 from underground diesel mining equipment. This is the first technology proven to control both PM and NO2 emissions for a cleaner, healthier working environment. The Mining CRT is also cost-effective compared to other technologies."

Jan 1, 2019

By J. U. MacEwan

THE basis on which the modern metallurgical industry is operated is the endeavour to attain maximum return in purchasing power for the least expenditure of energy. This has always been the general objective of the industry, as of all industries. In recent years, however, it has received a new emphasis. Today, as never before, increased attention is being directed to the detailed study of plant operations and the application of scientific knowledge and of business principles in order to achieve the maximum efficiency. This new emphasis is the result in large part of the new problems and conditions with which the industry has been confronted, chief among which are the following: (l) Development of new ore-bodies and the treatment of complex ores. (2) Necessity of achieving a greater degree of purity in some of the metals in order to meet the newly discovered demands for some of the industrial metals. (3) Discovery of new markets for many of the metals, either in pure form or in the form of alloys. ( 4) Change in values, absolute or relative, of some of the important metals. (5) Increasing scale of investment in expensive plant and equipment, which makes imperative most efficient utilization if total unit costs are to be kept to a minimum. (6) Increasing scale of operations in some important branches of the industry, which also makes essential maximum efficiency in organization, administration, and operation. The success with which the metallurgical industry has met the problems created by these changing conditions has been due primarily to the following factors: (1) Results of research and experimental work carried on by universities, government laboratories, and many private corporations in the industry itself. (2) Closet study of every detail of plant operation, both from the technological and from the economic point of view, with the object of increasing plant efficiency. (3) Interchange of information and experience amongst the operating companies. It is only by the concerted efforts of numerous investigators and experimenters that the underlying fundamentals of plant operations can be learned. The exchange of results permits their easy assembly and correlation with maximum benefit to the whole industry. Unnecessary duplication of research and experimental work is avoided and the industry as a whole is able to reap the fruits of this work with the maximum of-speed and efficiency. (4) Advances made in recent years in so-called 'scientific management' in industry as a whole and the application of the principles learned to the metallurgical industry. A review of the modern trends in extractive non-ferrous metallurgical processes illustrates the afore-mentioned new conditions and problems, and gives some idea of the methods by which they have been and are being surmounted.

Jan 1, 1937

By Thom Mambe, Angelo Fernando

The objective of this work was to identify key parameters related to the reduction of the sulphur content in ammonium diuranate (ADU), and the identification of solid products being formed under various operating conditions. A laboratory-scale, continuous ADU precipitation circuit was assembled using a glass reactor vessel immersed in a temperature-controlled water bath. A pre-prepared uranium feed solution was fed continuously using a peristaltic pump. Anhydrous ammonia mixed with compressed air was metered and pumped using a double-headed peristaltic pump. An over-head mixer was used to keep the solids in suspension. The precipitated ADU slurry was removed from the reactor at the same flow rate as the feed solution. The slurry was sampled to generate ADU solids for chemical and physical analysis after four hours of continuous operation to ensure steady-state conditions. The following variables were studied to determine their influence on the sulphur content in the resulting ADU. (a) sulphate:uranium molar ratio in the reactor (1:1, 1:5, 1:10 and 1:20) (b) precipitation pH ( pH 6, 6.5, 6.9, 7.5 and 9) and (c) precipitation temperature (40C and 60C) A total of 18 tests covering the above parameters were conducted, and the results indicated that the sulphur content in the resulting solids was highly dependent on the reaction pH. Out of the pH levels tested, tests completed at pH 6.9 and 7.5 generated solids containing the lowest sulphur contents, between 0.5 to 1.5% S uranium basis (UB). The sulphur content in solids was found to vary linearly with the sulphate:uranium ratio in the feed solution, showing a statistically valid correlation. The impact of temperature was minor between 40°C and 60°C, with a slight advantage at higher temperatures. Tests at a sulphate:uranium ratio of 1:1 produced solids with the lowest sulphur contents. The influence of pH or temperature on sulphur content in solids was almost non-existent at this sulphate:uranium ratio. Precipitation pH is the major factor influencing ADU sulphur content, followed by the uranium to sulphate ratio.

Jan 1, 2020

By U. Storck

"Shaft sinking for exploitation of the deep potash beds in Saskatchewan involved great difficulties from the very first because of the need to exclude from the shaft the high-pressure water encountered in the overburden. Control of the troublesome Blairmore quicksands was achieved relatively quickly by use of the freezing method and by lining with cast iron tubbing. The unsolved problem remained, however, of sealing the water-bearing Devonian where the formations had extremely low permeability and were thus hard to grout. Long experience in German potash mines had shown that the permanency of the whole mine would be seriously endangered if large amounts of unsaturated salt water were allowed to flow in from the shaft wall and merely removed by pumping. The prevention of water movement and the resulting dissolution of salt in the overburden were known to be most important. In the Alwinsal shaft, water flow from the Devonian has been prevented by the use of a steel and concrete sandwich lining similar in principle to a kind of lining introduced a few years earlier, and for another reason, in German coal shafts. As its installation is neither more expensive nor more time consuming than that of cast iron tubbing lining, this same lining was also chosen as protection against the Blairmore quicksands. The great advantage of the steel lining, in addition to its relatively high strength, is the fact that it is possible to make the joints of the individual segments absolutely and permanently water-tight by means of tested welds. The virtual dryness of the Alwinsal shaft will also result in lower costs because significant corrosion of all its steel installations, including skips, cage and ropes, will be prevented."

Jan 1, 1968

By M. Courtin, D. Berthelot, M. Haggis, D. McClarty, R. Payne

Over forty years of uranium mining in the Elliot Lake region of Ontario (1956–1996) has resulted in the production of over 300 million pounds of uranium. With the completion of mining activity, Rio Algom Limited and Denison Mines Limited are utilizing progressive environmental technologies and management systems to reduce and manage the environmental risks associated with the 150 million tonnes of potentially acid-generating tailings in nine regional waste management areas. Water covers designed to reduce oxygen entry and, thereby, significantly inhibit acid generation, have been applied at six of the sites with the Quirke site serving as a demonstration site for the Mine Environmental Neutral Drainage program. All five of Rio Algom Limited’s effluent treatment plants are monitored and controlled from a central control station utilizing a Supervisory Control and Data Acquisition (SCADA) system based on “Fix Dmacs” technology. Scheduling, auditing and reporting of plant operating and environmental monitoring programs for the entire watershed are controlled utilizing the Regional Environmental Information Management System (REIMS). Proper application of these technologies and management systems facilitates delivery of cost-effective environmental monitoring, care and maintenance programs at these sites and provides tools to demonstrate compliance with all environmental performance criteria.

Jan 1, 1999

By D. Milne, G. Snell

"A new method to predict stope hangingwall failure in underground excavations is proposed. This method compares movement rate for stope hangingwalls, determined from changes in strain or deformation, with changing opening geometry. This geometry is represented by the effective radius factor (ERF), a measure of relative distance to supporting abutments from an opening surface point. This strain-ERF (SERF) approach is applied to an instrumentation program for Brunswick mine near Bathurst, New Brunswick. The SERF method for this case study predicted failure at an ERF of 13.9 m and hangingwall failure actually occurred at an approximate ERF of 12.4 m.RÉSUMÉ Cet article propose une nouvelle méthode permettant de prévoir la rupture de l’éponte supérieure des chambres d’abattage dans les excavations souterraines. Cette méthode compare la vitesse de mouvement des épontes supérieures des chambres d’abattage, déterminée à partir des changements aux niveaux des contraintes ou de la déformation, à la géométrie variable de l’ouverture au jour. Cette géométrie est représentée par le facteur du rayon effectif (ERF, de l’anglais Effective Radius Factor), une mesure de la distance relative jusqu’aux appuis latéraux de soutènement à partir d’un point de la surface d’ouverture au jour. Cette approche contraintes-ERF (SERF, de l’anglais strain-ERF) est appliquée à un programme d’instrumentation pour la mine Brunswick située près de Bathurst, dans le Nouveau-Brunswick. Pour cette étude de cas, la méthode SERF prévoyait une rupture à un ERF de 13,9 mètres (m); la rupture de l’éponte supérieure s’est effectivement produite à un ERF d’environ 12,4 m.INTRODUCTIONUnderground stope design can be improved with the installation of field instrumentation. The most commonly used instrumentation for monitoring rock mass behaviour around open stopes is extensometers. The y-axis of Figure 1 represents how the changing rate of movement, measured using either displacement- or stress-type instruments, can be observed over time. The magnitude of movement measured by extensometers can give an approximation of the load on installed support (Milne, Pakalnis, & Lunder, 1996) and a changing rate of movement can indicate approaching instability."

Jan 1, 2018

Access to accurate real-time information is critical to maintaining efficiency and competitiveness in any modern minerals processing facility. At MMG LXML Sepon Copper Operation in Lao P.D.R., controlling the copper grade of the feed to the leaching circuit is paramount for maximising productivity and copper recovery. Since 2008, real-time analysis data has been available to process engineers from the Geoscan on-belt analyser installed on the Copper Mill feed conveyor. Access to accurate real-time results from the Geoscan has allowed the process engineers to strictly control blending based on copper grade to overcome variability in the plant feed, where conventional sampling and laboratory analysis is difficult, error prone and time consuming. In addition to enjoying these benefits since the Geoscan’s installation, in recent times the process engineers have expanded the use of the Geoscan by observing elemental results other than copper grade to control different aspects of the operation, focussing on the reduction of Gangue Acid Consumption. This paper discusses the process of expanding the Geoscan use at the operation, including an explanation of the calibration process. Additionally, a brief description of the Geoscan and its use at MMG LXML Sepon Copper Operation is provided, as well as a summary of recent calibration and analysis results. A discussion of future works concludes the paper.

Jan 1, 2016

By W. T. Robson

ONE of the problems encountered in any mine is the effect of increasing pressure manifested by increasing depth. Although the depth at which excessive pressure assumes serious proportion, and the manner in which it appears in underground workings, are influenced by a variety of factors, nevertheless the difficulty is present in all mines and its gravity increases with increasing depth. In the Kirkland Lake camp, as far back as seven years ago, mining had proceeded to depths sufficient to result in the formation of pressure great enough to cause violent disruption of masses of rock. It is proposed in this paper to deal with the effect of pressure caused by mining as observed at Lake Shore Mines, and to describe some of the methods which have been adopted to counteract it. There are many contributing factors in a study of the problem, and results vary widely in individual mines and in different localities. One feature common to all, however, is that there is ground subsidence, evidenced either by a gradual settling accompanied by crushing and shearing of the ore and wall-rocks, or the disruption of the ground surrounding the periphery of an excavation may take place suddenly, attended by more or less violent shattering of the rocks. Such violent failure of a mass of rock has been designated by the term rock-burst. The history of rock-bursts extends over a great number of years. They have occurred in some form or other in practically ali places where mining operations, at all but very shallow depths, have been carried out. Since the theoretical aspects of the subject have been dealt 'with at great length by capable and experienced writers (1), the present paper will give only a brief résumé of the theories propounded by those engaged in deep mining operations in various parts of the world.

Jan 1, 1940

By Staff

"The Weyburn Oil Field, located 80 miles southeast of Regina, Saskatchewan, was discovered by Central-Del Rio Oils Limited, in January, 1955. As of January 1st, 1959, the field had 357 wells capable of producing an estimated total of 45,100 barrels of oil per day.Highly portable, economical, drilling rigs are used to penetrate the pay at a depth of 4,400 to 5,100 feet. Presently, the complete drilling operation for an average field well, including drilling, coring, testing, and running casing, requires 12 days. Drilling procedures are conventional for a field of this depth and no serious problems exist. Central-Del Rio core the productive section of all their wells, which provides valuable information for well completions and reservoir studies. Production casing procedure is to set through the zone and perforate the productive inter-val. This was found advisable due to the lensing nature of the porosity and permeability throughout the reservoir, and to the high connate water saturation encountered in the tighter sections of the reservoir in the north and northeast areas of the field.Although a few wells in the field have produced naturally by flowing or pumping without acid treatment, it has generally been necessary to acidize the wells to make them commercial producers. To date, acid treatments appear to effect better stimulation of the limestone reservoir than fracturing treatments. Perforation sealing balls have been used as an aid in selectively treating all of the perforated interval.The majority of the field is on pump, producing at a low gas-oil ratio. The main part of the field has water-free production, with most of the water being produced in the north and northeastern area. Salt-water disposal is now available in the field through two disposal wells completed in the Basal Blairmore sand.The Midale Beds ""Marly"" and ""Vuggy"" zones form the principal reservoir, which is a stratigraphic trap, with the north and northeast edges terminated by a porosity and permeability pinch-out and the south-west and west edges bounded by water-laden porosity. There is no evidence to date of a gas cap. The reservoir apparently is producing on a fluid-expansion-type mechanism. The increasing water production in wells on the southwest and west edges of the field indicated water encroachment from these directions, and suggests some recovery energy may be available from this source.The total probable ultimate remaining recoverable reserves have been estimated at° 332,469,000 barrels of oil. Markets have not been able to keep up with the rate of development of the medium crude re-serves. However, it is felt strongly that substantial additional markets for Weyburn medium crude will be developed by the producers in the near future at realistic wellhead prices."

Jan 1, 1959

By L. T. Loe, A. S. Norsk, Mo i. Rana

High production rate and good stability demand the optimization of all phases of electric pig iron smelting. This is important with respect to slag chemistry, which to a large extent regulates the process temperature in electric smelting. Controlled basicity and slag volume. and a satisfactory screen analysis of the reduction material and sinter, are of the utmost importance for smooth furnace operation. Large variations in slag volume and in B/ A and C/Fe ratio will have an influence on the furnace resistance and thus the specific energy development in the furnace, which lead to variable reduction of SiO.. The result will be variable hot -metal quality and un-stable furnace operation.

Jan 1, 1970

By M. A. Gomez, V. Yahorava, J. A. Strauss

"It is accepted widely that pressure oxidation (POX) is the most appropriate technology for processing of arsenic containing refractory gold ores. However, studies on the stability of various iron-arsenic precipitates formed during POX are limited. Since the behaviour of these phases could have significant practical implications for gold processing plants, it is important to study them in isolation. This paper compares two synthetic precipitates, basic ferric arsenate sulphate (BFAS) and basic ferric sulphate (BFS) in terms of their formation, behaviour during hot curing and cyanidation, as well as their environmental stability. BFS and BFAS were synthesised hydrothermally at 205°C and their mineralogy was confirmed using various techniques. During synthesis, the addition of H3AsO4 into an aqueous Fe2(SO4)3-H2SO4 mixture significantly decreased the iron yield to BFAS in comparison to BFS under equimolar initial iron and acid concentrations. The BFAS dissolution kinetics was slightly faster, as compared to BFS, during subsequent hot curing. Cyanidation test work on the washed synthetic precipitates indicated that the lime consumption of BFAS was three times lower in comparison to BFS, while cyanide consumptions were comparable. Fresh BFS and BFAS precipitates, as well as their cyanidation residues, were found to pass the respective environmental tests in terms of arsenic release.INTRODUCTION Pressure oxidation (POX) is generally viewed as the most appropriate technology for the processing of arsenic-containing refractory gold ores due to the stabilisation of arsenic in the leach residue (Dutrizac & Jambor, 2007; Gomez et al., 2008; Harris, 2003; Collins, Berezowsky, & Weir, 1988). Detailed laboratory studies indicated that several Fe(III)-arsenate type compounds may be formed under typical conditions of autoclave treatment of refractory gold ores (Swash & Monhemius, 1994; Dutrizac & Jambor, 2007; Gomez et al., 2008, 2010; Gomez, Becze, Cutler, & Demopoulos, 2011). The basic ferric arsenate sulphate (BFAS) phase (Gomez et al., 2008), also known as Type II ferric arsenate (Swash & Monhemius, 1994) or Phase 3 (Dutrizac & Jambor, 2007), is one of the most common arsenic-bearing products (Harris, 2003; Dutrizac & Jambor, 2007). BFAS precipitation is viewed as one of the best routes for arsenic stabilisation and performed equally well to scorodite during environmental stability tests (Harris, 2003; Swash & Monhemius, 1994; Dutrizac & Jambor, 2007; Gomez et al., 2008, 2011)."

Jan 1, 2017

By A. P. Craig

"I HAVE BEEN looking forward to addressing this particular audience about Trans-Canada Pipe Lines because you men, more than most, understand the problems of the pioneer. Trans-Canada Pipe Lines qualifies as a pioneer on two counts: it is certainly pioneering a completely new industry in Canada -the long-distance transmission of natural gas -and it has at least a few of the problems that are expected and normal to any pioneering venture.This morning, I’m going to try to give you a sketchy picture of our project and a brief report on its current status and our progress to date; and then a broad picture of Canadian markets for natural gas.The physical characteristics of the Trans-Canada Pipe Lines project have been discussed so often that I am not going to take the time today to quote a lot of statistics on pipe sizes, miles, tons of steel, etc. Suffice it to say that this project, estimated to cost approximately $350,000,000, will be the longest large-diameter gas pipe-line ever built anywhere.Let me try to paint a broad picture of this great national project, using only a few basic 'round' figures.First, it involves exploration for and development of the natural gas fields in Alberta and other provinces -the cost of which will run into hundreds of millions of dollars.Then comes the gathering, stripping, and cleaning of the gas before it can be delivered to Trans-Canada. This will cost close to $100 million.Next we have the Trans-Canada Pipe Lines project for transmission of the gas to Eastern markets -estimated to cost $350,000,000 during the first three to four years and making natural gas economically available to one-half the population of Canada."

Jan 1, 1955

By M. Holmes, R. Molnar, E. Norton, K. Baxter, J. Riordan

The Boleo Copper-Cobalt-Zinc-Manganese Project of Baja Mining Corp. is situated adjacent to Santa Rosalia on the Baja Peninsula of Mexico. The El Boleo ore is a mixed oxide-sulfide deposit with major values in copper, cobalt, zinc and manganese. The metallurgical process designed to treat the El Boleo orebody involves a sulfuric acid leach in seawater using oxidative and then reductive leaching to maximize metal extraction. The leach solution is separated from the barren solids via counter current washing through a series of high rate thickeners. Copper is recovered using conventional SX-EW processing as cathode. Zinc and cobalt are extracted from the copper SX raffinate after iron and aluminum precipitation. The CSIRO DSX solvent system (Versatic® 10 and LIX® 63 mixture) are used in this extraction. Manganese remains in the DSX raffinate and is recovered by soda ash addition as a high quality manganese carbonate precipitate. Zinc and cobalt are acid stripped from the loaded DSX solvent. Zinc is then re-extracted away from cobalt using Cyanex® 272 extractant and stripped into a highly concentrated strip liquor (+100 g/L Zn) and directed to either a spray dryer or a granulator for production of zinc sulfate monohydrate. The zinc solvent extraction raffinate, containing cobalt, advances to another SX circuit using Cyanex® 272, for the recovery of cobalt as cobalt cathode. In this paper, the detailed results from bench and integrated pilot plant testing for zinc recovery from the El Boleo ore will be described. The results of this testing are currently being used to engineer the commercial plant at El Boleo.

Jan 1, 2008

By Xiong Tong, Jiushuai Deng, Yingbo Mao, Lingyun Huang

Ammonium carbamate has been used as a reagent for the leaching of copper from the copper oxide ore found in the Honghe state, Yunnan province, China. In order to find the optimal conditions for the leaching of copper from this copper oxide ore,the effects of several processing parameters, including the concentration, time, temperature, particle size and stirring intensity have been investigated. The results of these optimization experiments showed that the leaching rate of copper reached up to 72.76% under the following conditions: liquid-to-solid ratio of 10:1, ammonium carbamate concentration of 2.5mol/L, leaching temperature of 45 °C, stirring speed of 300rpm, a reaction time of 1.5 h and 85% by weight thereof passes through a sieve having 0.074 mm.

Jan 1, 2015

By Jason Mewis

Jason Mewis is the founder and president of ENGCOMP, a consulting engineering firm in Saskatoon Saskatchewan focusing on the mining sector. He has over 17 years of experience working on projects for the heavy industrial market in Saskatchewan, as both a Senior Structural Engineer and Project Manager. Jason is an entrepreneur with experience in many areas including estimating, planning, facilitation, and Risk Analysis. He has presented at many seminars and conferences across North America on the subject of Project Risk and and has become recognized for his expertise in this area of project management.

May 1, 2013

By Malcolm Black

Introduction The circumstances under which the gold mining industry was forced to curtail operations a few years ago are well known to all. The effect of those circumstances is particularly noticeable when one enters some of the larger mills that were designed, in better times, to treat relatively large tonnages. On their grinding floors one will observe that a number of grinding units are lying idle, and the ravages of rust are everywhere in evidence. The same applies to other equipment throughout these mills. In 1941, we found it necessary to reduce tonnage considerably in the Wright-Hargreaves mill. With the assumption that a lower tonnage would be of long duration, we began to focus our attention on some of the idle equipment with a view to re-arrangement of the flow-sheet for greater economy of operation. In an article by the writer published in the Engineering and Mining Journal (March, April, and May issues, 1939) , it was pointed out that in designing this mill there was a very limited floor space available. The choice of thickening equipment was imposed solely by the necessity for space: conservation. Thickening by gravity would have required 5,000 square feet of floor space, whereas Genter thickeners required only 1,200 square feet. As a consequence, the Genters were chosen. The decision to add flotation to the circuit was made primarily to save space. On a cost-plus-tail basis, 80 to 100 hours agitation on all pulp would produce similar overall results, but would require much more space.

Jan 1, 1948

By Jun Xiao, Xiaodong Li, Chunming He, Daixiong Chen

"Benzohydroxamic acid with double dentate can react with copper to form cyclic hydroxyl oxime acid copper chelate, indicating a good selectivity for copper oxide minerals flotation, especially for malachite. The flotation results of the pure malachite mineral show a strong synergistic collecting effect between hydroximic acid and xanthate at a ratio of 3.5:1, achieving a malachite recovery of 95.5% when certain sodium sulphide is used as a sulphidizing agent in the optimal pH range. Thanks to the synergistic collecting effect, the flotation recovery of malachite of a real refractory ore flotation ,can reach over 92% under the optimum condition, a 12% higher than the recovery achieved with the conventional collectors. In industrial application, the flotation of the copper oxide minerals is improved , leading to a high efficiency utilization of copper oxide resources.INTRODUCTIONBeneficiation of copper oxide ore is one of the recognized challenges in mineral processing industry. Copper oxide ore is a vital component of copper resource in the world, which has abundant reserves. Majority of sulphide deposits has oxidized zone on the top, and some deposits are oxidized to become the large and medium-sized oxide deposits (Willam & Chavez, 2001). Most copper oxide ores have problems in processing such as high slime consumption, poor floatability, complex ore property and low flotation recovery, so it is of great significance in beneficiation of copper oxide ores to develop an efficient collector, especially for malachite (Fu & Gu, 1997; Wen, 2010; Riet, Kier & Elford, 1980). At present, sulphidization-xanthate flotation is the most important method for treating copper oxide ore. In recent years, due to the decreasing ore grade, the utilization of refractory copper oxide ore draws more and more attention (Zhou, 2003), except for sulphidization-xanthate method, chelating flotation method (Lu, 2009), chemical beneficiation method (Lenormed, Salman & Yoon, 1979), microwave radiation flotation method, hydrothermal sulphidization-flotation method (Mao, Wen & Fang, 2014) and ammonia leaching of sulphide precipitation-flotation method (Lekang, Stevik & Bomo, 2003) have occurred."

Jan 1, 2016

By Patrick Mclaren, Peter B. Hale

Canada, with one of the largest continental shelf areas in the world, has done little to evaluate its offshore unconsolidated mineral resources which include heavy minerals (gold, chromite, rutile etc.) and industrial minerals (silica sand and aggregates). During glaciation much of the continental shelf was covered with an ice sheet and later subaerially exposed with the result that glacial, glaciomarine and fluvial processes deposited sediments that may contain heavy minerals derived from onland locations. With rising sea-levels, beach and nearshore processes may have served to concentrate heavy minerals by winnowing and removing the lighter mineral components. These potentially valuable resources can be found with suitable exploration techniques such as seismic profiling and bottom sampling. Gold deposits are known to exist off the coast of Nova Scotia, and on the basis of form er beach mining, gold deposits probably occur off Vancouver Island and the Queen Charlotte Islands. Large deposits of silica sand occur near the Madeleine Islands and it appears likely that supplies of marine aggregates are present close to urban markets or sites of future mega-projects such as oil field developments. This paper, which is based upon a review of literature and consultation with members of the Department of Energy, Mines and Resources' Coordinating Committee on Ocean Mining (DCOM), is the first step in assessing the Canadian offshore f or its resource potential with respect to quantified deposits, known and speculative mineral occurrences. Although this is a subjective evaluation, the potential appears promising. A more detailed resource inventory is required to provide a more certain assessment.

Jan 1, 1984

By James A. H. Church

This paper is in the nature of a protest against the dangerous propaganda afoot for the prevention of new mining undertakings and which is based on the imaginary 'blue ruin' conditions supposed to exist in the industry. An article by Mr. G. R. Pratt, A.M.E.I.C. in the first issue of the Western Canada News, February 2nd, 1925, and entitled "Review of Coal Mining in Alberta", is an excellent example of this type of propaganda. The article is a tissue of misstatements, faulty deductions and erroneous conclusions. For instance it contains the statement that some coal measures in Alberta are mined at great depth - whereas we all know that there is no coal mined at great depth anywhere in the province; another error is the classification of all mines under one head irrespective of whether they are mining prospects, 'country banks', or pukka mines equipped with railway facilities; and I believe that suppressio veri is tantamount to suggestio falsi. The bulk of his article hinges on a Table 1, which shows the details of coal produced in Alberta during 1923. Studying this table Mr. Pratt, in the manner of a conjurer producing rabbits from a hat, offers the following for the confusion of the public:- (1) "Waste effort, want of capital, waste of coal resources which result from unrestricted development"; the fact being that the waste is due to the failure of the Department of the Interior to exercise the powers which are inherent in the form of lease.

Jan 1, 1925

By F. A. Forward

Introduction The main line of ascent in the development of the nickel industry may be traced back through the International Nickel Company of Canada, Limited, to its earliest antecedents, the Canadian Copper Company and the Orford Copper Company. Mining geology is but one aspect of the overall development of this organization, and the stress it has placed on geology grew according to the need. In the early days, intensive geology was not required because ore supply was not one of the main problems of this or any of the pioneer companies. The difficulty then was to find economic methods for reducing the ores to nickel and copper, and markets for absorbing nickel in the face of a limited demand from consumers heavily prejudiced in favour of the New Caledonia product. "Very early in the history of the region it was patent to everyone that to share in the full benefits of the industry the same individuals or company must control the whole of the operation necessary to manufacture the finished product' (1, p. 45). These conditions were fulfilled for the International Nickel Company in 1902 when the Canadian Copper Company (incorporated 1886), with its ample ore supply, took the initiative to merge its interests with those of the Orford Copper (Refining) Company (incorporated 1887) to form the new company which, with reorganizational changes, emerged as the producer of the overwhelming bulk of the world's nickel. The Mond Nickel Company, Limited, entered the field in 1899 with a refining process, and over a period of years acquired ore through purchase of mining properties. This Company operated successfully and independently until 1929 when its assets were joined with those of the International Nickel Company in order to permit the most economic exploitation of the Frood-Stobie orebody in which both Companies were interested.

Jan 1, 1948