Search Documents

By W. R. Hargrave

"Mining OperationsOre will be mined by open pit techniques. Because of the high grade of the deposit and the low strip ratio, mining rates are small relative to most other open pit operations.The ore deposit is located in the valley of the main fork of Red Dog Creek. The bulk of the deposit is located on the southwestern flank of the creek, but mineralization does traverse the creek in both the north and east directions.Erosion has exposed the orebody in a number of locations, and has resulted in oxidation of the mineralization closer to the surface. Although much of this oxide material is very high grade, it leaches readily and, at least in the initial phases of the operation, will be stockpiled and not treated in the concentrator.During construction, 2.3 million mt. (2.5 million st.) of overburden and waste will be stripped from the orebody to expose ore for initial operations. Competent non-mineralized waste will be used to build roads and waste dumps, but the bulk of material removed consists of oxide or ice-rich soils and weathered rock which is not suitable for construction.The annual ore mining rate will be 1.9 million mt. (21. million st.). The strip ratio will start off at 1.2 to 1, falling to 1.0 to 1 by year 5 and ultimately to 0.8 to 1.Bench heights are set at 7.6 m (25 ft). Pit slopes will vary depending on the material present in the wall. The slope, through competent waste and the sulphide package, was set at 45 degrees. This is flattened to 26 degrees (i.e. 2: 1) through overburden and Upper Kivalina shales. The Kivalina Shales are an ice-rich shale whose carbonate matrix has been leached out and which exhibits little or no strength as it thaws. In addition, a 100 ft containment berm will be left in the wall below overburden and Kivalina."

Jan 1, 1989

By D. R. Lentz, J. A. Walker

"Abstract -The Flat Landing Brook Zn-Pb-Ag deposit of the Bathurst Mining Camp occurs within a narrow thrust-bound nappe containing felsic volcanic and volcaniclastic rocks of the Tetagouche Group. Within the host nappe, the Tetagouche Group is represented by the Nepisiguit Falls Formation and the overlying Flat Landing Brook Formation. The Nepisiguit Falls Formation is divided into two members: quartz- and quartz-feldspar-phyric volcaniclastic rocks ± minor lavas (Grand Falls member), and aphyric, fine-grained volcaniclastic rocks (Little Falls member). The Flat Landing Brook Formation consists of aphyric rhyolite flows and interbedded pyroclastic rocks. Several gabbroic intrusions occur in both the footwall and hanging-wall sequences. These gabbros locally cut out the mineralized horizon at shallow levels, and are considered to be feeders to tholeiitic basaltic flows (Forty Mile Brook member) of the Flat Landing Brook Formation. The Flat Landing Brook deposit has many of the characteristics typical of volcanogenic massive sulfide deposits occurring within the highly productive Nepisiguit Falls Formation in the eastern part of the Bathurst Mining Camp. Mineralization occurs within or at the top of the Grand Falls member and comprises four or more massive to semi-massive sulfide lenses that vary in thickness between 3 and 5 m. Massive lenses are laterally gradational to, or underlain by, zones of disseminated sulfides up to 38 m thick. The deposit contains an estimated resource of 1.7 Mt grading 4.9% Zn, 0.94% Pb, and 19.54 g/t Ag to a depth of approximately 150 m. From 150 to 300 m below surface, mineralization is low grade and mostly disseminated. However, below 300 m, ore-grade (>10% Pb+Zn) massive sulfide lenses have been intersected over mineable widths. Oxide facies iron formation overlies and (or) grades laterally into the sulfide lenses. The oxide facies has strong positive Eu anomalies and gently sloping rare earth element (REE) profiles suggesting that it was formed from relatively hot acidic fluids that had interacted with felsic volcanic rocks in the footwall. In contrast, the silicate facies iron formation that is more distal to sulfide accumulations has very weak positive Eu anomalies and gently sloping REE profiles, suggesting either cooler hydrothermal fluids or dilution of the hydrothermal component by detrital material. Hydrothermal alteration has affected most footwall rocks. Most notably, albite-destructive alteration has resulted in Na2O depletion, whereas mass addition of K2O is manifested in the formation of sericite (white mica). In more intensely altered quartz- and feldspar-phyric volcaniclastic rocks of the Grand Falls member, feldspar destruction is accompanied by chlorite alteration, producing quartz-phyric rocks similar to those in the footwall of many Bathurst Camp deposits."

Jan 1, 2006

By I. Le May

"The assessment of integrity in plants is discussed, together with the codes that are being developed for in service evaluation of engineering fitness for service. The use of Risk Based Inspection is described and some examples are provided of the evaluation of in service components in which flaws have been detected. An example of the assessment of the structure of a mine processing facility is described, and application of Risk Based Inspection and plant assessment procedures to mines is discussed. Periodic assessment of large plants and components to determine their integrity for continued safe operation is becoming a more accepted approach than formerly when regular shutdowns were the normal practice. This is on the way to becoming the preferred procedure for petrochemical plants and power generating plants, and the same philosophy is appropriate for many mining operations. Both the American Petroleum Institute (API) and the American Society of Mechanical Engineers (ASME) have committees developing codes for the continued operation of equipment as distinct from the existing design codes. The philosophy is one of risk-based inspection, which can be on a purely qualitative basis or more quantitatively based.The purpose is to reduce the inspection of unnecessary and non-critical items and to concentrate on the most critical components, reducing costs and downtime and increasing safety. The approach differs from that considered by many maintenance engineers, in that defects that are identified during an integrity evaluation do not automatically cause a component or structure to be condemned or require that repairs are made right away. The seriousness of the defect must be considered and the safe operating life can be estimated before it becomes necessary to replace or repair the unit or component. This is no different from what is done today with passenger aircraft and, to an increasing extent, with pressure vessels, reactor vessels and similar components in the petrochemical and power generating industries."

Jan 1, 1998

By Louis R. Bernier

Since 1978, most systematic studies of AMD passive treatment with limestone drains (LD) have dealt with coal mines in the United States. The authors present in this paper the first results of a triennial study initiated in 1999 on the performance of LD installed at the Ni-Cu Lorraine old mine site in Temiscamingue during a remediation plan that involved the installation of a cover with capillary barrier effects (CCBE) over the reactive pyrrhotite-rich tailings. Typically, a LD is a trench enclosed by impervious materials filled with crushed limestone and may be oxic or anoxic. Four LD (one filled with marble and 3 with dolomite) were installed at the Lorraine site. The LD have been in operation since May 1999 and are performing differently. The most contaminated mine effluent flows south and is directed towards 3 LD filled with crushed dolomite, while a 4th LD was filled with crushed marble and installed west. The LD filled with marble has been generating maximum alkalinity since the beginning of the passive treatment. Two of the dolomite drains have been generating alkalinity since mid-summer 1999, but one is not, even if a substantial pH raise was observed. A pH above 5.5 is required usually for the dolomite drains to start generating alkalinity. The installation of LD at the Lorraine site contributes significantly to the reduction of metals and sulphates loading.

May 1, 2001

By R. E. Legg

This paper gives a brief outline of the mining and milling methods which will be used on the Stirling zinc-lead-copper ores by Stirling Mines, Limited, who have for the past two years been developing the Stirling mine in Richmond county, Nova Scotia, and who will bring the mine into production in November, 1929. No attempt has been made to give the paper a detailed technical character, for the main reason chat, since base-metal mining is something new in Nova Scotia, it is felt that a general description would be preferable before this Society, whose membership is mainly made up of chose engaged in the coal mining and associated industries. Furthermore, as both mining and milling operations will be governed to a certain degree by the experience gained after production commences, there are many points which cannot be definitely stated now. GEOLOGY Before discussing the mining methods, it is desirable to present a general picture of the geology and occurrence of the ore-bodies. The surface rocks in the vicinity of the mine consist of rhyolites of .pre-Cambrian age. These volcanic flows outcrop in very few places, usually along' the beds of creeks or on the shores of the numerous small lakes. Consequently, a detailed geological map is not available. The exploration work carried out to date has revealed a sheared zone extending through the volcanic flows for a distance of over 1,000 feet. Along this zone, there has been a replacement of the rhyolites by a carbonate rock for widths varying from 50 to 230 feet, and it is in this carbonate formation chat the mineralization at a later date took place.

Jan 1, 1929

By J. C. Allan

THE purpose of this paper is to outline the pogress made in the development o the gravity separation method o ore dressing known as Sink-and-Float, which, in the opinion of the writers, has now reached a stage justifying the claim that this new method marks a highly important advance in the technique . The essential feature of the newest development of this process is the extremely accurate separation achieved. This is responsible for higher extraction in the sink-and-float unit on coarse sizes and, in consequence, for substantially higher overall recoveries. Whilst this is the most remarkable feature of the new process, it has further important contributions to make to ore dressing under the following heads: (1) The introduction of the sink-and-float separator as a buffer helps to iron-out irregularities in the mill feed. By supplying a concentrate of constant grade to the flotation section, the process also indirectly improves overall recovery. (2) The addition of a sink-and-float unit to an existing mill results in substantial increase in capacity at low per ton capital cost. (3) Where the plant can be installed underground for the pre-treatment of low-grade ores, there is a saving in hoisting costs, and excellent 'fill' is provided near the point of use. ( 4) Low-grade mixed oxide-sulphide copper ores may be pre-concentrated, thereby producing a flotation feed sufficiently rich to render the oxide residue from such flotation economic for subsequent treatment by leaching or other methods. (5) Application of the process eliminates hard gangue constituents which cause high grinding costs, or gangue constituents which adversely affect flotation. The plant is compact and easily controlled. No highly skilled operators or expensive reagents are required, and the labour and power per ton are low. The separator is extremely flexible, working equally efficiently on any throughput up to its maximum capacity.

Jan 1, 1940

By C. J. R. Braithwaite, Giancarlo Rizzi

"The Navan zinc-lead ore deposit (70 million tonnes) is hosted principally (97%) by the Meath Formation (Lower Carboniferous, Courceyan, Navan Group), comprising a lower, mainly carbonate mudstone unit, the Stackallan Member, and an upper grainstone-dominated unit. TheStackallan Member, about 60 m thick, comprises about 35 peritidal cycles including an oolitic grain-stone interval. Grainstones forming the upper part of the formation, about 150 m thick, comprise at least six shallowing-upward ramp cycles. Emergence horizons are indicated by subaerial dissolution surfaces, in situ breccias, and a single palaeosol.Most dolomitization at Navan is con?ned to the Meath Formation. The linear dolomite body,trending NE-SW, has a ?attened, laterally limited, tabular geometry in cross-section, suggesting that dolomitizing ?uids initially rose vertically, cross-cutting stratigraphic and sedimentological bound-aries, although ?uid ?ow was subsequently controlled by these features.Three stages of dolomitization are indicated by textural relationships, cathodoluminescence (CL),oxygen isotopes, and ?uid inclusion data. Stage 1 crystals, with generally dully luminescing cores and up to six overlying subsidiary zones, are the main replacive phase. Crystal surfaces are commonly corroded and overlain by bright stage 2 rhombs (which also form new nuclei lining molds and fractures). Three subsets of zones are present in stage 2 crystals: bright, non-luminescent, and dull; these are locally separated by additional corrosion surfaces. Stage 3 comprises relatively large baroque crystals, generally dully luminescent but with up to seven sub-zones. Isotopic and ?uid inclusion data suggest growth of successive stages from waters which became progressively hotter(60°–160°C).The distribution of the ores follows the dolomite trend. Ores were precipitated between Stages1 and 2 of dolomite growth, following Stage 2, and also during the nucleation and growth of Stage3 crystals. Dolomitization and mineralization appear to have been temporally and genetically related. The cyclic sedimentation of the host rocks, which accentuates lithological and petrographical contrasts between depositional units, controlled dolomitization. The relationship between dolomitization and mineralization, which is closely associated with faults, provides powerful exploration criteria. The recognition of these features in limestones elsewhere in the Irish ore ?eld may point toward unrecognized zinc-lead prospects."

Jan 1, 1997

By C. J. R. Braithwaite, Giancarlo Rizzi

"Abstract-The Navan zinc-lead ore deposit (70 million tonnes) is hosted principally (97%) by the Meath Formation (Lower Carboniferous, Courceyan, Navan Group), comprising a lower, mainly carbonate mudstone unit, the Stackallan Member, and an upper grainstone-dominated unit. The Stackallan Member, about 60 m thick, comprises about 35 peritidal cycles including an oolitic grainstone interval. Grainstones forming the upper part of the formation, about 150 m thick, comprise at least six shallowing-upward ramp cycles. Emergence horizons are indicated by subaerial dissolution surfaces, in situ breccias, and a single palaeosol.Most dolomitization at Navan is confined to the Meath Formation. The linear dolomite body, trending NE-SW, has a flattened, laterally limited, tabular geometry in cross-section, suggesting that dolomitizing fluids initially rose vertically, cross-cutting stratigraphic and sedimentological boundaries, although fluid flow was subsequently controlled by these features. Three stages of dolomitization are indicated by textural relationships, cathodoluminescence (CL), oxygen isotopes, and fluid inclusion data. Stage 1 crystals, with generally dully luminescing cores and up to six overlying subsidiary zones, are the main replacive phase. Crystal surfaces are commonly corroded and overlain by bright stage 2 rhombs (which also form new nuclei lining molds and fractures). Three subsets of zones are present in stage 2 crystals: bright, non-luminescent, and dull; these are locally separated by additional corrosion surfaces. Stage 3 comprises relatively large baroque crystals, generally dully luminescent but with up to seven sub-zones. Isotopic and fluid inclusion data suggest growth of successive stages from waters which became progressively hotter (60°-160°C).The distribution of the ores follows the dolomite trend. Ores were precipitated between Stages 1 and 2 of dolomite growth, following Stage 2, and also during the nucleation and growth of Stage 3 crystals. Dolomitization and mineralization appear to have been temporally and genetically related. The cyclic sedimentation of the host rocks, which accentuates lithological and petrographical contrasts between depositional units, controlled dolomitization. The relationship between dolomitization and mineralization, which is closely associated with faults, provides powerful exploration criteria. The recognition of these features in limestones elsewhere in the Irish ore field may point toward unrecognized zinc-lead prospects."

Jan 1, 1997

By Matt Manson

Renard?1-10 kimberlite pipes and ?Lynx-Hibou?kimberlite dyke system within ?Foxtrot?property 50/50 JV with SOQUEM, Stornoway operator 2001: Discovery of the Renard kimberlite pipes 2003: Discovery of the Lynx-Hibou kimberlite dykes 2006-2007: Bulk sample program 2008: First 43-101 Resource and Preliminary Assessment 2009/2010: Updated 43-101 Resource

May 1, 2010

By M. Sagedahl

The off gas from a smelter is cooled and dust removed in an electrostatic precipitator before approximately 95% of the sulphur dioxide (S02) is converted to sulfuric acid. However, the tail gas may need to be polished to remove the rest S02 to meet demands. A flue gas desulphurization (FGD) system, as usually applied to S02 removal on coal and oil fired Power Station, is suitable for polishing tail gases from copper smelters. The ALSTOM Seawater FGD process makes use of the alkalinity in the seawater to absorb and neutralize S02. Before being returned to the sea, the seawater is treated to comply with environmental regulations. As the ALSTOM Seawater FGD process uses no reagent and produces no byproduct, it is extremely cost-effective for coastal installations. The first SWFGD plant started operation in 1968. Over 60 of these units have been installed worldwide. The ALSTOM Seawater FGD process removes S02 from flue gas flows corresponding to a total of 70,000,000 Nm3 /h. Suitable for thermal power stations, smelters and oil refineries, ALSTOM Seawater FGD plants efficiently treats flue gases in the range of 300,000 Nm3/h to 2, 700,000 Nm3 /h per FGD plant, containing 20 - 6,500 ppm of S02.

Jan 1, 2007

By Grant S. Diamond

THE BIBLIOGRAPHY on the use of static electricity in mineral beneficiation consists largely of patents. Some references are found in mineral textbooks, but very little data on flow-sheets of commercial installations are known to the writer. As a matter of fact there have been relatively few successful commercial applications of importance. Johnson prepared and published a Table showing the polarity and static field intensity requirements of many minerals. There have been reports of successful beneficiation of rutile, zir-con, coal, potassium chloride, and phosphate rock. Otherwise, the field of success has been very limited. This may be due to three reasons: first, the mining industry has been averse to dry processes, be-cause of dust nuisances in dry crushing; second, the electrostatic processes used in the past apparently developed no substantial economic advantages; and third, because flotation or other . methods have proven successful on many minerals, the industry has not felt the need for a radically different process. In the feldspar industry there was ?an attempt at electrostatic beneficiation about twenty years ago which was based on the use of fluoride fuming of the pegmatite head feed, in order to make the mineral reactive in a static field. This process was originally said to be successful, but was discontinued because of corrosion damage to machinery. Another effort by use of a chemical additive such as an or-ganic hydroxyl compound has also been attempted. Neither of these processes is known to be in use today.

Jan 1, 1957

By B. Leonard

As of November 2012, the Alberta government listed 53 oil and gas, oil sands, and mining construction projects either proposed or currently under construction. These industrial plant construction projects have an estimated value greater than 105 million dollars. A common construction method employed for industrial plant projects is fast-track construction, which is used to reduce construction time. Contractors begin fast-track construction with highly generic scheduling information. This high level schedule turns into a lower level schedule as more detailed information becomes available. From a contractor?s perspective, a challenge faced using fast-track construction is the visualization of generic and constantly changing project schedules. This paper discusses the use of a Plant Information Modeling (PIM) system, designed to create a 4D animation to visualize project schedules for fast-track industrial plant construction projects. The proposed PIM system creates a modified project schedule by obtaining specific information from a generic construction schedule. Obtaining the information involves grouping schedule activities in accordance with the level of detail in a 3D model, and the level of detail in a project schedule. The modified project schedule is then used in conjunction with a 3D model to simulate the construction sequence in the form of a 4D animation. This allows for 4D visualization of project activities, installation dates, and crane movements. Furthermore, as engineering reaches completion, the PIM system creates a streamlined channel for schedule information updates to be easily uploaded into the model for a more accurate 4D visualization. Through analyzing a nonmodular construction case study, this paper discusses the successes and benefits of the PIM system for 4D visualization, such as increased productivity, shortened construction time, increased constructability, and decreased field costs.

Aug 1, 2013

By Thomas S. Falk, Nils G. Lindberg

The first industrial COBO (Cold Bound) pelletizing plant began operation in May 1975 at Trollhiittan, Swede n. A technical description of the process, together with operational experience with the plant, forms the basis of this paper.

Jan 1, 1976

By V. Taylor

"THE petroleum industry in Canada has been experiencing considerable difficulty in filling its manpower requirements during the last few years, and because of the rapidly expanding nature of the industry it is concerned about the supply that will be available to fill the needs of the future. As the oil industry is one of the more technically oriented industries, the most acute problem exists primarily in the field of profession-al/technical personnel. This is particularly true in the production and exploration side of the business, because it employs the highest percentage of this type of personnel. Let me illustrate this by giving you some figures reported by the Alberta Bureau of Statistics as of December, 1965 -out of a total of 9,641 male employees engaged in oil producing and geological and geophysical operations in Alberta, 3,021, or 31 per cent, were classified as engineers, geologists, geophysicists, managers and other professional personnel. No figures are available for 1946 to make a direct comparison of the expansion of the industry over the past twenty 466 years, but it is doubtful whether more than 100 professional/technical people were engaged in producing in Alberta at that time"

Jan 1, 1967

By Stephen G. Mlot

The evaluation of mineral projects involves the identification, mitigation and management of significant uncertainty. Benchmarking is an essential and effective way of increasing confidence and reducing uncertainty associated with input parameters and assumptions. Comprehensive and detailed benchmarking will ensure ?best practice? technologies, methods and systems have been considered and that the appropriate practices can be identified and incorporated into the project. In conjunction with the involvement of experienced industry practitioners, benchmarking is best employed throughout project evaluation to enable early identification of ?errors?, producing more accurate and predictable outcomes. Considerable time and effort is required to gather data and information, which should be benchmarked by the project evaluation team. There is a history of mining projects underperforming, on production, on costs and on return to the investors. The quality of mine plans and feasibility studies, and the quality of the input data is being questioned in many ways. Benchmarking assists sound project evaluation practices, by providing a database of actual results, to validate project inputs and outcomes, ensuring they are realistic and achievable. Benchmarking also provides unbiased, statistical support as the basis for sound investment decision making and ensures well considered decisions are made resulting in a more efficient study process. The evaluation of the quality of projects which are the subject of transactions also benefits from the use of real data obtained from a benchmarking database. Vendors are quick to highlight the benefits of their projects, and conceal the flaws, inflating the value. Buyers will want to quantify the potential of a project through the due diligence process relying on actual results from benchmarking. For the reasons broadly outlined above, benchmarking should be considered as an essential component of effective Project Evaluation.

Aug 1, 2013

By Mafalda Arias

Most mining and mineral exploration companies? operate in remote locations, in Canada or internationally. Not knowing the cultural imprint of your team and the places where your company is active, may lead to problems. To set the foundation for a better world, it?s important to built trust and relationships inside your global team, within communities and together with stakeholders. Building the ?invisible asset? and developing intercultural awareness is an important part of leadership programs for geologists and engineers on your team, and should be a key component of your Corporate Social Responsibility initiatives. Why is culture important for mining and mineral corporations in their CSR initiatives? Because culture is the foundation of your organizational identity. Understanding the impact of identity, for an organization and for each individual, will provide a description of the experiences and values that affect every work placed interaction, with your clients, with colleagues, with suppliers, with the community of the host country. Each one of us sees and evaluates the world through our perceptions. Through these perceptions we give meaning; how we view and understand our reality which sets the tone for how relationships are built. This is what I call building the ?invisible asset?. Identity, experiences, values and beliefs are invisible commodities, locating them can be as difficult as finding a mine. But if they are not located, the commodity does not have value. Just like in the work we do in our industry. For example when you are working in an underground gold mine and the vein is lost, you keep on working and trying to find the vein; time passes, money is being used and no results. You decide to bring an expert on this type of deposits who gave you directions that allowed you to find the vein. To be a responsible citizen of the world and to set the foundation for a better world, it is imperative to go deep, as deep as your next drilling program, because only there and then, can you develop the cultural sensitivity and the ability to become an agent of change for responsible, sustainable and profitable businesses.

Oct 1, 2010

By S. P. Narayan

The hot deformation behavior of Pure Mg and Mg-0.29Ce alloy were studied by isothermal hot compression tests in the temperature range of 250 - 500°C and strain rate range of 10-3 - 102 s-1 in a computer-controlled 50kN servo hydraulic universal testing machine (UTM). The results show that the flow stress of Mg pure and Mg-0.29Ce alloy increases with strain rate and decreases after a peak value, indicating dynamic recovery and recrystallization. Process efficiency was increased by nearly 10 to 12% by addition of Ce in Mg. Mg pure exhibits instability zones between 250-275°C at 10 ? 102 s-1 and 400¬500°C at 101 ? 102 s-1 temperatures and strain rates respectively, rest is the safe deformation zone. Wherein, Mg-0.29 Ce exhibits two low efficiency zones from 250 ? 300°C at 10-2? 10° s-1, 400 ? 500°C at 101 ? 102s-1 and high efficiency zone at 450 ? 500°C at 10-3? 10-1s-1. 4D process maps were generated for the above said alloys which illustrate contours of power dissipation and instability in the 3D space of strain rate, temperature and strain.

Jan 1, 2011

By G. F. Colborne, A. Thunaes

"When the Canadian uranium milling plants went into operation during the early 1950's, they utilized flowsheets developed at the Radioactivity Division of the Federal Mines Branch in Ottawa. Since then, numerous process improvements have been made by the Mines Branch, by the operating companies themselves and by other research organizations. This paper will consider uranium milling technology from the standpoint of a new mine operator charged with the responsibility for the design of an economic flowsheet, and will indicate the range of process elements available to him and the testwork required to enable an intelligent decision to be made."

Jan 1, 1968

By Richard J. Haslinger, C. Mark Rebagliati, James L. Oliver

Abstract - Exploration at the Specogna gold deposit has identified a geological resource of 65.0 Mt grading 1.63 g/t Au, which equates to 3 million ounces of contained gold. This resource is hosted in a low-sulfidation epithermal deposit of Miocene age that is localized along the northwesterlytrending Sandspit fault. The fault has juxtaposed Late Cretaceous mudstone of the Haida Formation to the west, with Late Tertiary coarse clastic sediments and lesser andesitic volcanic rocks of the Skonun Formation to the east. A plagioclase porphyritic dacite dike intrudes the Haida mudstone and Skonun sediments along the fault. Gold mineralization, in hydrothermal breccias, veins and stockworks developed mainly in Skonun sediments and dacite. These are formed in an 800 m long zone that roughly parallels the Sandspit fault. The gold zone is funnel-shaped in cross-section, approximately 300 m wide at surface, 220 m above sea level, and narrows to approximately 50 m, at sea level. The deposit lies within an elongate zone of moderate to intense hydrothermal alteration that, at surface, extends over a known area of approximately 2 km2. Its western extent is bounded by the Sandspit fault. There is an asymmetric alteration zonation, with a core of silicic-potassic (adularia) and smectite-illite clay alteration that is bounded to the east by argillic alteration. Similar zoning defined by the distribution of metals reflects the position of the main feeder conduit. Mineralization of altered wallrock is dominated by 1% to 4% auriferous pyrite and marcasite. Gold and silver occur as electrum; individual silver minerals have not been identified. Other sulfides are rare, and are identified only microscopically. The mineral suite is typical of low-sulfidation epithermal systems. Gold occurs in early, multi-phase, variably bladed and banded quartz veins and breccias, which are cut by barren, single phase, drusy quartz veins.

Jan 1, 1998

By L. H. Rajala, K. H. Singh

"This paper presents the results of a detailed feasibility study carried out to investigate whether a low-grade deep underground mine of Falconbridge Nickel Mines Ltd., closed since 1975, could be made more productive and profitable by the introduction of new mining technology. For this purpose, recent advances in mine design and development concepts, larger and better designed machines, such as hydraulic drills, high-pressure down-the-hole machines, LHDs, new blasting concepts, more efficient and improved stoping methods, and ground control technology were considered. Technical and economic analyses incorporated the latest computer-based techniques. The mine was reopened in 1979 and the paper concludes with an assessment of actual progress and performance compared with that planned and forecast.IntroductionThe East Mine orebody, located between the Falconbridge Mine and Inco's Cryderman Mine in the Sudbury District of Ontario, has been in production since 1956. From 1956 to 1978, about 5.6 million tons of ore had been mined from this ore zone. The ore body is low grade and was developed as a cut-and-fill operation. Due to high operating costs, the mine has been shut down several times during economic downturns. The latest closure was in 1975 due to a lower demand for metal.In 1978, investigations were initiated to assess the economic and technical feasibility of mining this ore using new developments in mining technology. In this study, consideration was given to the application of bulk mining methods with a potential for higher productivity, trackless development utilizing efficient LHD machines and hydraulic drills, new blasting and fragmentation concepts, and new ground control technology. Advanced computer techniques, such as finite element, for mine design and rate of return with discounted cash flow analyses for the economic comparison- of various mining options were utilized for a rapid and comprehensive assessment during the feasibility stage."

Jan 1, 1981