Search Documents

By G. M. Brownell

Introduction Within the past year a new deposit of gypsum has been opened up and brought into production in the Province of Manitoba. Until 1930, Manitoba's entire production came from Gypsumville, northwest of Winnipeg, at mile 161 on the Gypsumville branch of the Canadian National railway. However, during 1930 a gypsum bed was opened up at a point one mile south of the village of Amaranth, forty miles north of Portage la Paririe, on the west side of lake Manitoba (See Figure 1). Although no exposure has yet been discovered, the presence of gypsum below the surface in that district has been known for many years as the result of drilling for water. In 1929, J. R. Spear (1), of Winnipeg, interested some local capital in the possibility of .finding commercial deposits of gypsum, and, after some exploration work in the area with a well drill, the Amaranth deposit was located. Sixteen holes were put down at intervals of 400 or 500 feet, all of which encountered what appeared to be a continuous bed of gypsum, about thirty-eight feet thick, at a depth of 92 feet. The extent of the deposit has not yet been determined.

Jan 1, 1931

By C. H. Bertoni

"The Superior Province of the Canadian Shield is the largest gold producing area within Archean greenstone rocks in the world, with total production of over 140 million ounces of gold. One hundred and fifty-five mines have individually produced more than 8,000 ounces, although only a relatively limited number of deposits (33) produced more than one million ounces of gold. The output from these 33 deposits accounts, however, for 85% of total gold production. The majority of grades (68%) ranges between 0.10 and 0.30 ounce per ton, and there is no linear relationship between grade and tonnage.Development of new gold mines reflects the history of gold prices. However, the response to the latest increase in gold prices was not as marked. It is concluded that gold deposits are becoming increasingly more difficult to find and new exploration techniques are urgently required.IntroductionWith most of its production coming out of the Superior Province, the Canadian Shield is the largest producer of gold from Archean greenstone rock s in the world. In total gold production, the Superior Province is surpassed only by the paleo-placers of Witwatersrand and the placers of the USSR (Anhaeusser, 1976). There has been no attempt so far to compile the historical production of the Province as a whole in a single document. The aim of this work is to fill this gap, not only for the convenience of having a complete list of gold producers, but, more importantly, as a basis on which to study the tonnage and grade characteristics of these deposits."

Jan 1, 1983

By N. Novikov, M. Jastrzebski, N. Kryzhanovskaya, D. Shevchenko, I. Kapran, N. V. Novikov, T. Koehler, B. Zaporozhets

"The PFK FeNi Smelter was re-commissioned by Solway Resources in 2002, ending a long period of economic decline in the adjacent town. In 2009 Hatch was retained to design, supply and install a custom furnace crucible that would accommodate a capacity increase from 34 MW to 40 MW and increase campaign life through binding and cooling technologies, as part of ongoing improvement efforts. The involvement of PFK personnel was critical to the successful integration of the new furnace technology with the existing process and operational practice. The furnace upgrade project was completed in 18 months during 2010 – 2011. Since start-up, the furnace has exceeded production expectations, operating successfully at 42 MW.INTRODUCTIONAfter ceasing operations in the 1990’s, the Pobuzhsky Ferronickel Combine (PFK), located in central Ukraine, was stripped of useful equipment and deteriorated while dormant. The surrounding town experienced a period of economic decline throughout the 1990’s. Solway Industries purchased the complex in 2002 and began a systematic incremental program to re-commission the smelter using both local expertise and specialists from other parts of the former Soviet Union. This led to the re-birth of PFK as a successful toll-smelting complex, and a renaissance for the surrounding economy.As part of the continuing improvement program, PFK approached Hatch in 2009 to study the possibility of a capacity expansion from 34 MW to 40 MW. It was decided, based on the results of the study, to design and install a custom furnace crucible integrating the unique PFK FeNi process with modern Hatch furnace technology. This novel approach had many benefits, including: maximum re-use of existing furnace components (off-gas, feed equipment and transformers), minimal impact on upstream and downstream equipment and building structure, and the retention of a familiar operating regime. The latter was a key factor in the success of the project, as it allowed the extensive operating expertise of the PFK staff to remain highly relevant to the upgraded furnace. This led to minimized capital investment, a rapid start-up and no significant operational challenges switching over to the new equipment incorporating Hatch furnace technology."

Jan 1, 2012

By D. C. Sharpstone

THE Polaris-Taku mine is a new gold property, situated in the far north-west corner of British Columbia. Production was started in November, 1937, at the rate of 150 tons a day, and recently has been increased to 200 tons. The property, which promises to become one of British Columbia's important gold mines, was developed and brought into production in twenty-nine months after work was started on it as a virtual prospect in June, 1935, by Edward C. Congdon and associates. Inaccessibility, extraordinarily complicated geological problems, and difficult metallurgy retarded development of the property before acquisition by the present interests, an::l, in fact, discouraged two companies that had spent substantial sums upon it from continuing development. This paper is concerned with reviewing the development of the property and describing the principal features of the geology, the mining and metallurgical practices, and the equipment employed. Acknowledgments The writer is indebted to Mr. Edward C. Congdon, President of the Polaris-Taku Mining Company, and to various members of the mine staff for their assistance in assembling the data for this paper. Special thanks are due to Mr. George G. Griswold, Jr., of Butte, Montana, who generously and painstakingly prepared the section dealing with milling and power. Microscopic studies of ores were made by Professors Frank Grout an::l G. M. Schwartz, of the University of Minnesota, and by Mr. Griswold.

Jan 1, 1938

By CIM Environmental, Social Responsibility Society

Within the mining industry, the pathway from exploration, to planning, construction, operation and closure has become more complex over the last few decades. The current financial, environmental and social influences present the mining industry with unprecedented challenges and opportunities. In addition, international environmental and social reporting standards and codes are becoming increasingly robust. The reporting requirements provide an added impetus for issuers to effectively manage environmental and social impacts and risks. Reporting requirements also provide the opportunity to be transparent. The intended audience for these Environmental, Social and Governance (ESG) Guidelines for Mineral Resource and Mineral Reserve Estimation includes practitioners, industry participants at all levels of skill and experience, corporate management and board members, government agencies, academic institutions and interested parties. For practitioners, this document provides underlying key principles of environmental, social and governance practices. The ESG Guidelines provide guidance for those using environmental, social, governmental and governance information when preparing and implementing mineral exploration programs and contributing to the preparation of mineral resource and mineral reserve estimates for mineral properties that are either at the study stage (i.e., scoping / preliminary economic assessment, pre-feasibility, or feasibility studies) or in operation. The guidelines can also be used to help mineral resource and mining companies apply good practice to manage their environmental and social risks and opportunities. Companies can identify and retain appropriate professionals to prepare environmental and social materials to support company studies. The guidelines are also a resource for companies developing effective environmental and social management strategies at any project stage. This document is not intended to be prescriptive and is not intended to provide exhaustive guidance on what to consider in terms of environmental, social, legal and governmental modifying factors in the preparation of MRMR estimates. Rather, it is intended as general guidance to assist companies and practitioners in considering and applying these modifying factors for MRMR estimates. This document is also not intended to guide environmental and social impact assessment (ESIA); however, the measures needed to manage impacts help inform the constraints and costs for defining mineral resources and mineral reserves and inform the costs and schedules of mineral project studies. All documentation of MRMR estimates made by an issuer and intended to be, or reasonably likely to be, made available to the public in a jurisdiction of Canada must comply with the requirements of National Instrument 43-101 Standards of Disclosure for Mineral Projects (NI 43-101), as amended from time to time (Canadian Securities Administrators, 2016a and 2016b). Disclosure is not addressed in these ESG Guidelines. Determination of what to include in disclosures is defined in the applicable Securities’ legal frameworks. Appendix A presents a summary table showing the linkage of the principles and topics in these ESG Guidelines to the potential effects on project costs, schedules, government permits and approvals, social licence to operate and financing.

Sep 8, 2023

By Lawrence Nordell

A Conjugate Anvil-Hammer Mill (CAHM) has the potential to replace conventional crushers and SAG mills, with their respective conveyors and stockpiles, in a SABC circuit. It may improve comminution circuit efficiency by 100%. CAHM compresses rock in a more efficient way, similar to 19th century stamp mills, which follows the fundamental research of Schönert (1990 & 1996). CAHM efficiency is being proven through the use of ROCKY (2011) Discrete Element Method (DEM). ROCKY features allow it to simulate realistic comminution. CAHM is customizable with many geometries that are rock-property specific. ROCKY?s wear modeling compliments the structural integrity of the design.

Jan 1, 2012

By D. R. Boyle

"The basal type uranium deposits in south central British Columbia occur within unconsolidated, late Miocene fluvial paleochannel sediments that overlie major fault zones within the Okanagan Highlands Intrusive Complex. Prior to the formation of mineralization, paleovalleys containing host sediments were flooded by Pliocene valley basalts of the Plateau Basalt Formation. Five uranium deposits have been outlined to date, of which the Blizzard (4020 tonnes U) and TYee (650 tonnes U) are the largest. The basement intrusive complex underlying the deposits varies in age from early Cretaceous to Eocene and is comprised of quartz monzonite, granodiorite, Coryell monzonite, porphyritic granite and pegmatite.The mineralized host sediments comprise a complex sequence of interfingering conglomerates, arkosic sandstones and mudstones. Organic material is abundant in many, but not all, mineralized beds. Uranium mineralization is present in the form of uranous (ningyoite) or uranyl (saleeite, autunite) phosphates coating clastic grains and filling voids. Because of very strong reducing conditions related to large concentrations of marcasite and organic material, ningyoite is the only uranium mineral in the Tyee deposit, whereas the Blizzard deposit contains a more complex assemblage of minerals (saleeite, autunite, ningyoite). The observed paragenetic sequence of mineral precipitation in the Blizzard deposit (autunite-saleeite-ningyoite) indicates that the uranyl minerals, saleeite and autunite, are primary. Small amounts of Zn, Ni, Co and Mo have been introduced into the Blizzard deposit whereas Mo is the only non ore-forming element enriched in the Tyee deposit. Mn is the only depleted element in both deposits."

Jan 1, 1986

By The Staff

Introduction For many years the necessity of mechanization of all the underground services in the collieries of the Dominion Steel and Coal Corporation in the Sydney, Pictou, and Cumberland coalfields has been foremost in the minds of those concerned with the engineering and operating policies of the Corporation, and a gradual policy of the mechanization of these services has been undertaken over the years, until nearly all the underground services, except the actual loading of the coal at the face, have been mechanized. Early in 1928, experiments in mechanical loading were conducted which finally culminated in the installation of mechanical loading units in our No. 20 colliery in 1938. This attempt at mechanization of the final underground services proved unsuccessful because the workmen were not ready to accept complete mechanization, and the fruition of many years of study was delayed until the year 1947. During the ensuing years, the engineers and operators of the Corporation had studied the possibility of adapting to conditions prevailing in Nova Scotia mines the many types of loading equipment in use in the United States and Europe. The varied physical conditions which exist in the fields operated by the Corporation rendered it extremely difficult to apply the equipment and technique successfully employed in the United States, and more recently in Europe, and special techniques have had to be devised to meet the need of each individual colliery. Prevailing physical conditions in the Nova Scotia fields find no parallel for mechanization with those of any other part of the American continent.

Jan 1, 1949

By Alan E. Gallie

One of the requirements for the successful waging of war is an unlimited supply of iron ore. In the spring of 1941 the demand for iron ore was expected to exceed the supply. This was particularly so in the case of high-grade lump iron ore, essential to the open-hearth process of making steel. The bulk of Canada's iron ore was imported from the United States. At this time, Canada was making every effort to conserve United States funds for more vital purchases. For these reasons, the development of Canadian iron ore resources became of prime importance. Several companies undertook investigations and one of these examined the old Josephine deposit. Location The Josephine property is in the district of Algoma, in the Michipicoten area of the Sault Ste. Marie mining division of Ontario. It is 120 miles north of Sault Ste. Marie and 20 rail-miles east of Michipicoten harbour, on lake Superior (see Figure 1). Transportation in the area is furnished by the Algoma Central and Hudson Bay railway. The Michipicoten branch of this line passes within a mile of the Josephine mine. Michipicoten harbour provides a port through which iron ore is currently shipped. Power in the area is supplied by the Great Lakes Power Company, with generating plants on Michipicoten river, on Montreal river, and on St. Mary's river at Sault Ste. Marie. A series of transmission lines cover the district and one of these is connected to the Josephine mine by a 3 ½-mile branch line. History The Josephine property was staked by Alois Goetz in 1899. Before the claims could be recorded, the township in which they are located was given to the Algoma Central & Hudson Bay railway as part of a land grant. As a result, the ownership remained in dispute until August 24th, 1906, when a settlement was arbitrated by the Honourable Frank Cochrane. His ruling is interesting and is quoted in part.

Jan 1, 1947

By N. Saracoglu, J. P. Golightly, R. H. Wallis, J. J. Brummer

"The McClean uranium deposits are located 11 km west northwest of the Rabbit Lake Mine. Their average grade is 1.8 % U3O8 , and they contain 6. 350 tonnes of uranium oxide in seven pods of variable grade and mineral assemblage. They are hosted by both basal Athabasca Group and the regolith developed on the underlying crystalline basement. The major mineral facies are: sulphide, arsenide, 'bleached', and hematite, with the important uranium minerals being coffinite, uraninite and pitchblende. Abundances of carbon and sulphur isotopes are consistent with their derivation from pyritic graphite in basement gneisses. Isotopes of oxygen and hydrogen suggest equilibration at temperatures of about 200°C. Ar39/ Ar40 age determination of illite associated with ore suggest mineralization began about 1300 m.y. ago and that significant alteration had ceased by about 1170 m.y. ago though Pb/ U data suggest the deposits continued to evolve into the Mesozoic.IntroductionThe McClean deposits lie on the eastern side of the Athabasca Basin of northern Saskatchewan where they are part of a cluster of uranium deposits lying west of Wollaston Lake (Fig. 1). The general stratigraphy is schematically portrayed in Figure 2 which emphasizes that mineralization is hosted by both the Athabasca Group and the underlying regolith and also that the deposits are preserved at depth and have not suffered from preand post-Pleistocene weathering and erosion. This circumstance, combined with their simple shape and the presence of seven separate zones of mineralization (pods) allows a description, based on over 450 fully cored drill holes, to be made of the wide variation in chemistry, grade, alteration patterns and position relative to the sub-Athabasca Group unconformity. Ar39 / Ar40 age determinations have been made of illites associated with regolith, Athabasca Group and mineralization and studies are in progress on C, S, 0 and H isotopes of mineralized material and host rocks. Only some of these data have been published; Brummer et al., (1981); Golightly et al., (1982); Bray et al., (1982); and Saracoglu et al., (1983). The only other published data on McClean geology are by Tremblay (1982, 1983)."

Jan 1, 1986

By S. Castro, L. Gutiérrez, L. Uribe

"Use of lime in seawater as a pyrite depressant decreases Mo recovery in flotation of Cu- Mo sulfide ores. When technology that uses sodium metabisulfite (MBS) to depress pyrite is applied, the process is carried out at pH 6.5–7.5, the range where Mo recovery is higher than the usual pH 11.0–12.0 when lime is applied. Redox conditions and chemical reactions involved in depression mechanisms of pyrite by MBS, or sodium sulfite, in seawater are investigated and discussed based on the acidifying effect of MBS, oxidation of sulfite ions by dissolved oxygen, and the role of catalyst of some metal cations (e.g., copper ions) adsorbed on pyrite’s surface.RÉSUMÉ L’utilisation de chaux dans de l’eau de mer comme agent déprimant de la pyrite réduit la récupération de molybdène (Mo) dans la flottation de minerais sulfurés de Cu-Mo. Lorsque l’on applique la technologie utilisant du métabisulfite (MBS) de sodium comme agent déprimant de la pyrite, le procédé se fait à un pH de 6,5 à 7,5, gamme dans laquelle la récupération de Mo est supérieure au procédé habituel utilisant un pH de 11,0 à 12,0 lorsque l’on applique de la chaux. Les conditions de réduction-oxydation (redox) et les réactions chimiques impliquées dans les mécanismes de dépression de la pyrite par le MBS (ou sulfite de sodium) dans de l’eau de mer sont étudiées et débattues sur la base de l’effet acidifiant du MBS, de l’oxydation des ions sulfites par de l’oxygène dissous et du rôle de catalyseur de certains cations métalliques (par exemple les ions de cuivre) adsorbés à la surface de la pyrite. INTRODUCTIONThe copper industry is aware of the difficulties of floating Cu-Mo sulfide ores in seawater. Molybdenum recovery is partially depressed when lime is used to reject pyrite. In plant practice, sodium metabisulfite (MBS) has been demonstrated to be the most promising option for replacing lime in seawater."

Jan 1, 2017

By Roland B. Hoag, Roger G. Webber

Sulphate concentration in groundwater is a good measure of the extent of oxidation of sulphides, provided that sulphide minerals are the primary source of the sulphate. A study was conducted near the Eustis Mine in Quebec to determine where and how the sulphate in groundwaters originated. Atmospheric precipitation is the only source of sulphate other than oxidation of sulphides, and in this study area it is equal to 0.01,. millimole per litre. The oxidation of sulphides can be divided into subsurface oxidation (mainly inorganic processes) and surface oxidation (including both organic and inorganic processes) . The maximum sulphate concentration due to subsurface oxidation of sulphides depends on the solubility of 0 2 in water and is 0.25 millimole per litre. Surface oxidation is, therefore, responsible for any amount greater than atmospheric plus subsurface contributions (0.29 millimole per litre). Surface inorganic oxidation occurs in waters with a pH greater than 15 and is controlled by the kinetics of the oxidation processes. Organic (bacterial) surface oxidation is dominant only in acid (pH< 1.5) waters. The bacterial action accelerates the oxidation of sulphides, and large quanttties of sulphate may be introduced into solution.

Jan 1, 1976

By Michael Moats, Adirek Janwong

The use of cylinder electrowinning cells, such as emew® technology, for the recovery of silver from primary and secondary sources has been growing. In this study, common operating parameters used in silver electrowinning were evaluated for recycling applications. Silver powders were produced from an industrial solution in a laboratory scale emew® cell. A design of experiments was employed to evaluate the effects of HNO3 concentration, iron concentration, current density and solution flow rate on current efficiency, particle size, bulk density, and crystallographic orientation. Current efficiency was affected by each parameter with increasing HNO3 concentration having a strong negative effect, increasing iron concentration and current density having moderate negative effects and increasing flow rate having a positive effect over the ranges examined. Finer particles were produced with increasing current density and decreasing flow rate. Bulk density increased when HNO3 concentration increased. The crystallographic orientation of all powders was dominated by the (111) plane. Increasing flow rate decreased the relative intensity of (200) direction. Based on these observations, silver electrowinning in cylindrical cells can operate at high current efficiency and produce larger powders at low HNO3 concentration, low iron concentration, low current density and high flow rate.

Jan 1, 2014

By R. Boom

Corus Umuiden, formerly Hoogovens, was the first steel plant in Europe after Voest to introduce oxygen steelmaking. In the decision-making process contacts with Dofasco in Canada about the production of formability steel grades were crucial. In developing oxygen (LD-) steelmaking high liquid steel output rates had to be combined with accurate process control. For ingot casting static models with input control and sampling during interrupted blowing were sufficient to deliver liquid steel within the required carbon, phosphorus, sulphur and temperature windows. Computers were introduced to perform the complicated charge calculations. Continuous casting called for strict control of composition and temperature at process end point and made predictable timing crucial. Dynamic control was introduced based upon sub lance measurements and waste gas analysis. Reliable disposable measurement sensors were developed in a concerted international action. Dissolved oxygen at blow end deteriorated the quality of low carbon aluminium killed steel grades. Blowing gases through the converter bottom improved process kinetics, resulting in lower carbon-oxygen products, yield increase and better phosphorus removal and generated new families of hybrid blowing processes. Introduction of secondary metallurgy facilities such as argon stirring stations, vacuum degassers and ladle furnaces relieved the demands for strict BOF end point control. Desulphurisation of hot metal became standard practice. In regions with scrap shortage hot metal desiliconisation followed by dephosphorisation, was introduced in the blast furnace cast house and hot metal transfer ladles. Later redundant converter vessels were used for pre-treatment, resulting in a two-stage process. The fundamentals of oxygen steelmaking are described and a vision on the future is presented.

Jan 1, 2004

By R. W. Lawrence

"The management of acid rock drainage( ARD) to prevent impact when tailings are disposed of in the environment requires understanding of the phenomena giving rise to acidic drainage, a rigorous evaluation of the weathering characteristics of the tailings, and the successful implementation of control measures that will be effective in the long term. This paper provides a brief theoretical background to the complex reactions taking place in mill tailings containing residual sulfide minerals which must be appreciated to enable waste characterization program to be effective in predicting the future behavior of the tailings and in designing control methods which will work. The principals and practice of prediction and control as part of an ARD management strategy will then be discussed.Paper Not Available at Time of Publication"

Jan 1, 1997

By B. W. Smee

Glacial lake sediments or glaciolacustrine deposits form a significant portion of the Canadian, Scandinavian and Russian landscapes. Furthermore, 50 per cent of the Archean volcanic belts within the Canadian Shield area are covered wholly or in part by these deposits. Because of the high electrical conductivity and low hydraulic conductivity of these compact sediments, the application of geophysical (electrical) and geochemical techniques in such areas becomes a difficult task. The presence of these sediments has therefore hampered exploration for metallic sulphide deposits in some of the most important metallogenic environments of Canada. Similar problems exist in some tropical countries, such as Australia, where the overburden may be very conductive. In this paper, the extent and provenance of the glaciolacustrine deposits within the Canadian Shield are described. The geochemical and geophysical factors that hinder exploration in the clay belts are reviewed, with case histories of successful and unsuccessful applications of some of these techniques. The most successful geochemical technique used within glacial clay belts is the sampling of lodgement till beneath the clay cover, and the analysis of the heavy mineral fraction of that till. Surficial sampling has not been successfully applied. Some geophysical techniques, more specifically electromagnetic and magnetic induced-polarization techniques, have detected mineralization beneath substantially deep clay or saline overburden layers. Some suggestions have been made, such as the use of anions in hydrogeochemical surveys and the use of wide-band multi-frequency EM systems. When implemented, they will hopefully make the current geochemical and geophysical methods more effective in exploration for base metal sulphides within clay-covered terrains.

Jan 1, 1979

By Jerry M. Whiting, Neil J. Duncan

"Does Canada need a mining industry? Isn&apos;t it a chronically depressed collection of businesses that pollute the air and water and tear up the countryside? Wouldn&apos;t it be better if Canada&apos;s investors devoted their attention to high-technology endeavours, tourism, and other relatively pleasant tasks?Probably the answer to whether Canada needs a mining industry in the 21st century is to look at the real mining industry that is in operation today. The facts indicate that mining is a very important contributor to Canada. It has certainly encountered some challenging times during periods of recession, and it face s severe and continuing problems of cost and competition in world markets. However, uneconomic mines have been closed, others suspended, and productivity has risen dramatically with employment at 77 000, down from 101 000 in 1981. The country&apos;s metal and non-metal mines, metallurgical plants and semi-fabricated metals industries employed an estimated 378000 workers in 1986, and paid wages than any other sector of the Canadian economy. This effort resulted in the production of 60 different metals, non-metals and structural minerals valued at $13.5 billion.The trade aspects of the mining industry are of paramount importance. If there is a reason for this situation to change during the next century. it eludes the authors. Canada has the well-developed expertise to discover, evaluate, develop, operate and profit from existing and new businesses based in an enormous area endowed with a nearly unbelievable variety of mineral resources. Many countries throughout the world must rely on producers like Canada, if they are to maintain and/or improve their standard of living."

Jan 1, 1988

By Yoginder P. Chugh

This paper discusses design of sprays systems for dust control around a continuous miner (CM) in about 4.2 m (14 ft.) high mining areas with about 1.0 m to 2.0 m (3-6 ft.) of out-of-seam dilution mining. The challenges included low air volumes and velocity at the end of the line curtain, dust produced from out-of-seam dilution rock being very fine with 50% of the particles less than 10 micron, poor capture of aerosol through scrubber suction inlets, dust escaping through the sides of the loading pan in mining high areas, overloading of dust-laden air in the wet-scrubber, and dust rollback toward workers. The challenges were resolved through CFD modeling of airflows; improved line curtain installation, redesign and varying the spatial locations of spray systems as compared to low mining height areas. Water sprays on CM is the primary engineering control for dust control in coal mining. In 2010, the authors developed several spray system concepts for dust control (Chugh, Patwardhan, Gurley, & Hirschi (2009), Chugh & Gurley (2009), Chugh 2012). These included increased contact time between dust particles and water droplets, improved potential for the dust aerosol to be sucked in through suction inlets, and reduced dust-roll back to the operators and workers. CFD modeling was used to understand airflow patterns around mining areas and to identify spatial locations for sprays to minimize dust exposure of CM operator (CMO), haulage unit operator (HUO), and workers downwind of the operating CM in the last open crosscut (LOXC). Face area ventilation plays a key role in dilution and removal of dust generated by mining operations. High mining heights and large pillar sizes associated with longwall mining reduce the air volume reaching the face area to achieve good dust dilution.

Aug 1, 2013

By W. D. Watson

"Early in mine development at Quintette Coal Limited major problems were encountered with the fleets of primary equipment which seriously hampered production. These major fleets (cable shovels, hydraulic shovels, hydraulic drills and electric trucks) have consequently been the focal point of maintenance efforts. Some were prototypes in the Canadian mining scene and brought with them new concerns to test their skills. The problems were studied and the category and areas which were having the greatest impact on the reliability of the equipment were determined. Once defined, priorities were established and a program was initiated which was designed to accomplish a resolution. Resulting from implementation of this systematic approach, over the past three and one-half years, the fleets are now giving good reliability and industry standard availabilities. Along with these significant achievements, cost per operating hour on some of the equipment fleets has decreased substantially and continue a downtrend through 1987. This paper identifies the problems and describes the resolutions. IntroductionIn the early years of the mine development, Quintette Coal Limited (QCL) experienced production shortfalls due to problems with the major excavator and haulage fleets. A large fleet of hydraulic excavators had been purchased, and QCL was among the first northern users of all hydraulic blasthole drills. They were also using some prototype equipment and encountered problems which were not common on other types of equipment or were unknown.Because of these unique problems and lack of experience from other mines to draw on, an analytical approach was taken to areas and associated causes of the delays affecting the availability and reliability of equipment. This was done by dividing the equipment downtime into seven classifications of delays, i.e. maintenance, electrical, hydraulic, mechanical, damage, service and preventative maintenance, and tires; and then each was expressed as a percentage of total downtime. Subsequently each of the delay classification was divided into categories e.g. electrical to six categories - wheel motors, main alternator, relays, cards, no propel, lighting and 24 V system. Then, the basis for further study had been established.From this preliminary analysis of historic records, it was possible to determine the areas which were causing the majority of the downtime. These areas were then analyzed to evaluate causes and to determine possible solutions to the problem s. This paper addresses the major fleets, their problems and eventual solutions. Plea se bear in mind that the over-all objectives were to increase physical availability and reliability."

Jan 1, 1988

By G. E. Agar

This paper deals with the prediction of locked cycle flotation results from data developed from individual batch tests. A postulate is made that the distribution of material in a separation stage is determined by the chemical conditions and the flotation time and that this distribution can be characterized by split factors which are constants for a fixed set of conditions. With this premise, it is demonstrated that a steady-state balance can be calculated for a circuit. Although the necessary equations can be solved algebraically, a computer program was written that uses an iterative technique to arrive at the steady-state balance. The program is written so that a variety of circuits can readily be simulated. A number of examples are examined to demonstrate the validity of this simulation procedure. The sensitivity of the material balance to changes in the split factors was examined. Data developed from different flowsheets are presented on sulphide ores, on copper-nickel separation and on silver flotation.

Jan 1, 1978