Search Documents

By Jin C, Shu H

The effect of operating parameters of a shaking table on the separation of mixed quartz-magnetite artificial feed has been experimentally investigated by use of laboratory-scale shaking table. Based on a great number of experimental data collected, the multi-variate non-linear model of shaking table has been developed. The model allows for the calculation of the product grade and recovery. A computer model has been programmed, for inclusion in a software package for the simulation and optimisation of shaking table if the feed characteristics and the concentrate grade are given.

Jan 1, 1993

By Fulton E, Ring RJ, Waters DJ

Laboratory leach tests of Nabarlek uranium ore carried out by the Australian Atomic Energy Commission to compare the effectiveness of Caro's Acid1 (permonosulphuric acid) as an alternative oxident to pyrolusite indicated reduced acid consumption in leaching and lime savings in neutralisation of tailings liquors when using Caro's Acid. Interox Chemicals Pty. Ltd. arranged a plant trial for Caro's Acid at Queensland Mines Nabarlek Plant. The trial confirmed that significant savings in acid and lime can be achieved under plant conditions. Plant operations also demonstrated improved redox potential control was possible using Caro's Acid.

Jan 1, 1978

By Milner SC

Four quartz latite rheoignimbrite units (units I to IV) mapped in the Goboboseb Mountains have been traced to their eruptive source, the Messum intrusive complex; this is a complex multistage ring structure (18 km diameter) with well defined gabbroic, monzonitic, and syenitic intrusive phases, and a central ring zone containing mixed rhyolitic to latitic agglomerates. Three of the four quartz latite units are correlated with the upper and lower (2 units) Springbok quartz latites outcropping some 90-130 km north of McIsum. This implies minimum volumes of 300-500 km for wits I and III (Lower Springbok) and 2200-2600 km for unit IV (Upper Springbok). This latter unit is still ti 300 m thick at its outcrop limit, some 130 km from Messum. Each of the four units represents single cooling units. Lithologically, each can be divided into three zones: A basal, dark grey to black flinty or glassy zone, often with highly attenuated fiamme (ressembling flow banding); a central massive and strongly recrystallised zone; and an upper variable zone which exhibit breccias, contorted flow banding, and amygdaloidal to pumiceous clasts. Their overall characteristics tend to be intermediate between ash flows and lava flows. The rheoignimbrites are interpreted as the oproducts of dense, high temperature (950¦-1100 C) ash flows which underwent rheomorphism and lava-like flow prior to their final cooling.These large scale eruptions are related to the initial rifting of Africa and S. America, possiby in response to a major hot spot.

Jan 1, 1990

By W Whiten

The determination of mineral composition is necessary in the mineral sands industry. Tiwest has developed a procedure for safe and convenient determination of the mineral composition using a magnetic separation followed by chemical analysis using X-ray fluorescence spectroscopy. This then requires the conversion of the elemental assays to mineral compositions. A project at the Julius Kruttschnitt Mineral Research Centre has developed a convenient analysis method for this conversion. This analysis is based on a reconciliation of the of the assays of the sample with the standard mineral assays by making minimal adjustments based on the assay accuracies to both sets of assays. As well as providing the mineral composition it to be tested for other applications and variations of the procedure to be evaluated. Given a range of samples, testing for the accuracy of the assays of the standard minerals, has been demonstrated.

Jan 1, 2001

North Flinders Mines Limited (N.F.M.) is an Australian-owned mineral exploration and mining company based in South Australia. In the 1970's it researched the prospectiveness of the Tanami (central western region of the N.T.) for the identification of possible economic gold deposits. Having outlined the potential for such a deposit at The Granites (550 km. N.W. of Alice Springs), it marked out and in 1975 applied for the grant of eleven gold mining leases (G.M.L.'s) under the provisions of the then Mining Ordinance. This application was deferred by the Commonwealth Government during the time of the Aboriginal Land Rights Commission (Woodward), subsequent enactment of legislation and land claims. In 1980, the Walpiri and Kartangarurra-Kurintji land claim encompassing the G.M.L.'s, became Aboriginal land. It therefore became necessary for N.F.M. to negotiate a mining agreement with the Central Land Council (C.L.C.) represent- ing the Traditional Owners, before the G.M.L.'s could be granted. In August 1983, the C.L.C. and N.F.M. concluded an agreement to enable the grant of mining interests necessary for the devel- opment of The Granites Gold Project. In several ways this agreement is unique in That:

Jan 1, 1984

This paper investigates dry drilling as a feasible alternative to meet current requirements for improvements in mining productivity in an increasingly competitive world.A field test program was conducted in the surface facilities of a hard rock mine in Sudbury, Canada, to investigate the potential use of dry drilling in underground bulk mining as a conceivably faster and more economical method than wet drilling. The test work consisted of the monitoring of advance rates and bit life while a series of 165 mm diameter holes, wet and dry, were drilled with compressed air at both mine (0.69 MPa) and high (1.72 MPa) pressure levels. The results indicate that penetration rates can be increased by approximately 24 per cent by drilling dry with high air pressure and by approximately 27 per cent by drilling dry with mine air as compared with wet drilling under the same conditions. Dry drilling also has the effect of increasing bit life by up to 69 per cent. An economic analysis for typical hard rock mines indicated that drilling productivity and cost savings can be increased by approximately 23 per cent when dry drilling is utilised.The testing program indicates that dry drilling has the potential to become a feasible technique with regard to performance, productivity and costs.

Jan 1, 1991

By J Centofanti, D Conti, R Riske, C Morley, A Cook

Why is it so difficult? Why are there differences throughout the resources industry in how reconciliation factors are reported and calculated? Why is there no standard formula to use? These are common questions asked when mining companies try to compare reconciliation results across operations or attempt to undertake internal or corporate governance reporting processes. For many mining companies the calculation of reconciliation factors is often a very time and resource intensive part of mandatory reconciliation reporting. Some major mining companies, that move millions of tonnes of material per annum, dedicate full time resources to the calculation of reconciliation factors. The willingness of these companies to set aside resources demonstrates the value that operations place on good reconciliation reporting. Reconciliation is about measuring the variance between two like measures at different points along the mining sequence. It can be undertaken between predictive models, forecast plans and actual measured performance. Calculations are used to derive a variance between two sections within the mining sequence, with the result being commonly known in the resources industry as a æfactorÆ. Mining companies use the calculation of reconciliation factors as key performance indices (KPIs) to provide a æhealth checkÆ of their operation, with variances often pointing to issues either with the accuracy of the original estimate or the quality of the measurement being used in the comparison. There are many reconciliation factors that can be calculated and reported. This paper will set out, clarify and provide a recommended standard means of calculating each specific factor that, where adopted by a company, will ensure compliance with the international reporting codes, such as JORC. Using case studies from Rio Tinto Group (Rio Tinto) and BHP Billiton Mitsubishi Alliance (æBMAÆ), and the authors experience across a wide range of mine sites, the outline of a generic solution for tracking a parcel of material from the pit through to the port along with appropriate reconciliation factors is provided. The intention of proposing standardised reconciliation factor terminology and methodology is to provide the foundations of a system to enable communication and comparison across different commodities, companies and mines sites.

Jan 1, 2009

The quality of the external water source for a mineral processing plant may influence the extent to which the environmentally desirable practice of recycling of water from plant products is possible. This is particularly likely for froth flotation plants where the chemical quality of the water may affect the plantÆs performance. The quality of the external water source or the recycled water can be improved by a water treatment step, and in turn the extent of recycling which can be tolerated is able to be influenced. The quality of the external water can range from very high quality, soft water derived from melting snow, to poor quality, hard water (high levels of dissolved calcium and magnesium) from underground aquifers, and to even lower quality sea water (very high levels of dissolved species including sodium chloride). It can be noted that some underground water is more saline than ocean water as well as containing high levels of dissolved calcium and magnesium. Occasionally, a different source of water is utilised in the wet and the dry seasons. Increasingly, sewage water from cities is becoming a potential external water source with sustainability implications. If the initial quality of the external water is high, the scope for recycling of water from all the products is maximised. Such reuse or recycling of water from the products allows chemical species from oxidation of the ore and from other inputs to the process such as reagents to increase in concentration in the water returned to the plant. Such accumulation of species can have negative effects on the performance of a process such as froth flotation but instances of positive effects exist. Some reagents which are used in flotation plants such as lime or sodium carbonate also happen to be commonly used for independent water treatment plants. Hence, the flotation process may inadvertently provide some aspects of water processing. Where the quality of the water in the feed to a mineral processing plant (external water plus recycled water) is not an issue, more powerful solid-liquid separation processes can be considered to maximise the removal of water from the products and its reuse. Such processes may also have complementary benefits in a sustainable mineral industry by, for example, producing a tailing stream with a higher per cent solid value which is more suitable for safe storage on the surface or underground. This paper documents findings on the effect of water quality on the flotation process. It also considers current directions of change in the need for increased removal of water from plant products. It then considers the implications of these trends for maximisation of water recycling by such operations.

Jan 1, 2003

David Pollard will raise this matter in more aetail in a later paper, but mere are some obvious points that I wish to make. It is a relatively straightforward exercise to assess the competency at a low level in the workplace where the consequences of a worker's actions can be observed immediately. Assessing competency at higher levels which may involve creative, planning, design or supervisory functions is more difficult, especially where managerial responsibility and accountability for the output of others is involved. This is generally the case with the daily activities of most mining professionals, whether they be in operations, in a consulting capacity, in research, or in government.

Jan 1, 1994

Government geoscience may be categorised by objective under three headings: Applied Research for Geoscientific Framework Studies, Resource Inventory, and Technical Advice. In Queensland, the Department of Resource Industries is active in all three categories. Under the program-based management system adopted in 1987, three Programs, namely, Geological Survey, Mineral Resources Development, and Energy Resources Development and Utilisation, have geoscience responsibilities.Prime responsibility for geoscience resides with the Geological Survey Program, which provides a geoscientific framework for mineral and energy exploration and the development of the State. Simply stated, the Program goal is to provide geological information when and where it is required. Geological Survey work also encompasses aspects of resource inventory and technical advice, complementing the work of the other two Programs. This role has a 122 year long tradition, for geoscientists of the Geological Survey have been engaged in investigations designed to facilitate the identification and utilisation of the mineral, water and energy resources of Queensland since 1868.

Jan 1, 1990

Mond gas-producer tar, and, in fact, all tars obtained from the retorting of coal where steam and air are admitted to the retort, are of entirely different chemical composition to the ordinary coal tar made in the gas or coke works. These tars contain none of, the aromatic hydrocarbons - benzene, toluene, naphthalene, and anthracene, sought after by the ordinary coal-tar refiner.The distillation of Mond tar shows it to consist of phenols of high molecular weight, unsaturated hydrocarbons of high gravity and low viscosity, paraffin wax, and resinous substances of whose composition little is known.The physical properties of Mond producer tar are also peculiar. It has a "short," granular texture when cold, which might be likened to candied honey. It "dries" (hardens) when exposed in thin layers to the air, and, for a coal tar, it cannot be considered sticky. This latterò property, combined with the short texture, prevents its being used successfully for road-making or macadamizing.The drying properties and the paraffin wax contained in: this tar cause it to hold up large percentages of water, probably in the form of emulsion. When containing as much as 10% to 15% moisture it appears to be quite dry.

Jan 1, 1918

By Gardavsky V, Gabell AR, Green AA

The I,)hyllosilicate mineral chlorite is a common constituent of altered rocks associated with volcanogenic massive sulphide deposits, and literature studies indicate that, in general, this mineral is progressively enriched in magnesium relative to iron as an orebody is approached. Studies have shown that there is a direct correlation between the Mg/Mg + Fe ratio of chlorite and its absorption spectra in the 2.7 to 3.0 um range. However, this region, which contains the fundamental 0-H stretch absorption features, is affected by intense atmospheric absorption, and therefore cannot be used for remote sensing. At shorter wavelengths (0.4 - 2.5um), there are windows where the atmosphere is sufficiently transparent and vibrational absorption bands still occur, although they are clue to overtones and combinations, and accord- ingly are much weaker than the fundamental features. Shifts to longer wavelengths with increasing iron content can still be observed in this region of the spectrum and, with better spectral resolution and sensitivity, it may be possible to monitor subtle variations in chlorite chemist by remote sensing techniques.

Jan 1, 1987

The resurgence of mining over the last 30 years has coincided with a growing awareness in the community of the importance of environmental protection and conservation. This involves a growing concern about environmental degradation, an increasing desire for the setting-aside of natural areas for wilderness preservation, accelerating pressures for the return of large areas of Crown land to Aboriginal ownership and a widening view that economic growth itself may be undesirable (Burton, 1987). This has lead to much public debate over the implementation of sound environmental policies to achieve a balance between economic necessities and ecological goals.

Jan 1, 1991

The Transportable Moisture Limits, as ,measured by the procedures laid down in The IMCO Code of Safe Practices for Bulk Cargoes, determine the target moisture contents for the concentrates produced at the West Coast Mines of Electrolytic Zinc Company of Australasia Limited at Rosebery. Filtration of these concentrates gives moisture contents considered to be low in comparison with those achieved for similar sulphide concentrates, but which are very close to these Transportable Moisture Limits. The filtering techniques used are outlined and the problems associated with-maintaining concentrate moistures below the required limits, together with the methods used to solve these problems are discussed.

Jan 1, 1978

The Tregoora Gold Project is centred around the old Mitchell River Antimony Field located 100 kilometres west-northwest of Cairns, North Queensland. The project is currently the subject of a joint venture between Strategic Minerals Corporation N.L. and Hawk Investments Limited.Historical BackgroundThe Tregoora area was first prospected for antimony and gold around 1890. During the periods 1905 to 1914 and 1937 and 1944 approximately 100 tonnes of antimony and an unknown quantity of gold were won from a number of small mines the principal one being the "Retina". A strong increase in the demand for antimony in the early 1970's resulted in renewed exploration activity in the region and the re-development of the Retina Mine. Despite the intermittent interest in the region for antimony it was not until 1984 that the potential of the area for hosting gold resources was realised with the delineation by Strategic Minerals Corporation N.L. of a significant gold deposit now referred to as the Black Knight.

Jan 1, 1986

ITSL Technology group employs around 100 people at Mississauga in Canada. Its long and proud history as a driving force for the worldÆs nickel industry continues, progressively adapting to meet IncoÆs ongoing development needs. The nickel industry, unlike many others in the minerals processing world, has not evolved into one or two narrow technology paradigms. Rather, each process requires a degree of optimisation to meet the characteristics of the ore. Without a competent team to address this complexity, the uncertainties that arise can greatly increase the risk (and costs) associated with the nickel industry developments. The development work carried out at ITSL Technology ranges from milling and metallurgical processing of ores through to development of value added products for the battery and electronics industries. It covers routine evaluation of ores for exploration (mine planning and greenfield), and provides on the ground support to bring specialist technical perspectives to site-based projects. In recent years, ITSL Technology has had as its particular focus the process development and commissioning support for IncoÆs major projects. Over the next several years, Inco will commission its Goro laterite operation, design and construct the further processing facility for VoiseyÆs Bay, undertake major upgrades at Sudbury, Thompson and PT Inco, and bring forward some additional resources currently in the exploration stage. The appropriate mix of both internal and external resources to effectively manage this project portfolio will prove critical to success. The key to ITSL Technology meeting these development challenges has been in working closely with its internal customers to ensure alignment of the value proposition, to identify the critical issues to be managed, and to understand the deliverables required. This paper discusses examples to reinforce these principles in the definition and development for two different projects; processing of VoiseyÆs Bay ores and concentrates and resource optimisation at Thompson.

Jan 1, 2006

Just as Australia is part of the Pacific Rim, so the Pacific Rim should be viewed as part of the whole world. That applies in particular to that scarce commodity û money. There are five main factors of production in any mining development û mineralisation, materials, manpower, management and money. LetÆs focus on the upstream input û mineralisation, and the downstream input û money, especially in the area of communications. Unknown to many, the Competent Person reporting on Mineral Resources and Mineral Reserves has a direct and unavoidable impact on the companyÆs financial statements û the profit and loss account and balance sheet. With respect to reporting of the major asset of most mining companies û the resources/reserves û investors are getting a better deal now than at any time in memory as regards flow and adequacy of information. Australia has been a world leader in this regard. The outlook is for even more informative and useful reporting. The more rigorous reporting requirements for Exploration Results and Mineral Resources/Reserves, which have become a worldwide phenomenon over the last five years, will continue. This will be positive for the mining industry as a whole and for Australia in particular. However competition for the scarce investment dollar will also increase. Put simply, mining has many competitors, unconnected with mining, for the capture of the investment dollar. It behoves all participants to recognise that there are three investment factors which influence strongly the willingness of investors to put money into mining. These are Confidence, Credibility and Consistency. AustraliaÆs investment image stands high in these three respects, but the competition will continue to grow. AustraliaÆs lead must be maintained. However, some investment decisions should not necessarily be based on fundamental, quantifiable facors. Some of these are outlined.

Jan 1, 2004

By Oliver R

The Hamersley Iron ore resources are geologically complex with fluctuations in mineral chemistry. From this resource Hamersley Iron must produce consistently high quality direct shipping products and have the ability to evaluate the effects of changes in demand. In order to achieve these objectives an incremental long term planning technique has been developed. This method reduces the total geological resource statement into a simple, logical sequence of events. A logical sequence of mining increments is defined within individual areas based on a final pit and access system. Increment characteristics are derived manually and from a computer based orebody model. The end product of the technique, an optimum mining schedule, is readily developed from the incremental information. Among its many benefits, this simple technique rapidly provides management with information for policy formulation.

Jan 1, 1979

At many locations in Australia the decommissioning of mining operations will require the disposal of excess water. If the water is contaminated its disposal may be restricted by government guidelines. The timing of water disposal may be critical to the schedule of close-out. The uncertainty of the annual rainfall input to the water storage and disposal system may determine the success or failure of close-out. The uncertainty associated with any outcome can be used to determine the reliability of the system, or inversely its risk. The technique of Monte Carlo simulation, using the uncertainty in annual rainfall, is applied to quantify the risks associated with water disposal as part of the requirements for close-out in two case studies. In both case studies it is assumed that water disposal is via evaporation only. The first case study is the Nabarlek operation, located about 270 km east of Darwin. This project is required to complete the engineering work associated with its close-out by December 1995. The second study investigates the situation of close-out for the Ranger Uranium Mine, about 250 km east of Darwin. It should be noted that the Ranger mine was examined as part of the annual update of its contingency rehabilitation plan and the probability of implementing the plan is extremely small. The probability of success for the Nabarlek case varied from less than ten per cent to greater than 95 per cent depending on the management strategy. Four possible strategies were investigated for the Ranger mine with the chance of success varying between 20 and 95 per cent. The estimation of the evaporation rate and the area allocated to evaporation was critical in both cases. By applying seasonally based evaporation pan coefficients determined on site, rather than an average monthly value of 0.75, the chance of success was improved by up to 35 per cent for Ranger. Simulation modelling is able to provide information on the likely response of mine water management systems and the level of risk. This information is required to efficiently plan and manage the disposal of water for close-out.

Jan 1, 1994

IN any assay office it is of paramount importance to keep the men interested in their work; and in order to do this, men on routine work, such as lead, zinc, and sulphur deterrrrinations, slag analysis, etc, should be changed around monthly. This gives some variety and helps to keep a man's interest on his work, so that better work results. It may be maintained that to keep a man on the same class of work indefinitely makes him more expert at his work. This is certainly true; but in assaying, where accuracy is so essential, it is absolutely necessary for a man to keep his mind on the work, and not 'get' into a mechanical method of working. He is also on the alert to discover means for shortening his analytical methods, and his capacity forwork is increased. Another advantage is that the men get a good all-round training, and one is never at a loss to replace a man on any class of work when he is absent from any cause. This tends to smoother and more efficient running of the assay department. In industrial assaying it is often advantageous to have a result quickly, so that it will be of maximum benefit in the running of some part of the plant, In such a case it pays to sacrifice a little accuracy to speed up a method. The shortest method is less costly, and a quick approximate method is all that is required to give the superintendent the requisite information. Time is thereby saved, and the cost is less. In carrying out assaying for any large industrial plant, such as a smelting works, there is always a tendency for superintendents running the different departments to send in more samples for assay than are absolutely necessary when no system of costing is in operation. Some of these samples may involve a lot of work and heavy expenditure, as, for example, the estimation of only one impurity in a sample of refined lead. If the superintendent knows that the cost of assaying all samples sent in by,him is charged up directly against...

Jan 1, 1922