Search Documents

The cost of constantly extending a decline tunnel that plays a part in the actual extractive process is a revenue cost. The characteristics of such a decline tunnel are that it is dug in a series of relatively small excavations. It follows the ore body and is dug as close to the ore body as practicable. In addition, the decline allows for the extraction of ore in the immediate vicinity, with the ore being extracted in a relatively short period of time.

Jan 1, 1990

By D C. Laurence, J Holden

Seafloor massive sulfide deposits contain bonanza grades of gold, silver, copper and zinc metals. The deposits are often found at depths of one kilometre or more. They are characterised by active chimneys or smokers venting fluids at over 300¦C, with extremely low pH values. Mining of these deposits presents risks for both industry and governments at orders of magnitude higher than terrestrial mining This paper briefly discusses some of the core risks concerning the development of SMS mining including: technical, economic, environmental, legal, social, and research and development. Until and unless these risks are eliminated or minimised, the embryonic deep sea mining industry will remain just that, and these deposits will remain a fascinating, unexploited geological curiosity.

Jan 1, 2003

By A Thornton, D Engelhardt, J Woodg

Grinding is a critical part of nearly all mineral processing operations. It is the largest consumer of energy on the mine site (and thus indirectly a producer of greenhouse gas through the generation of electrical energy at the power station). Since comminution is one of the main consumers of electrical energy worldwide, efficient control of grinding mills is of paramount importance. Mill Auto-Pilot is a control system developed for SAG mills to stabilise load and power and improve the efficiency of control and increase throughput. A dynamic, mechanistic model of the grinding circuit is used to determine circuit parameters which can not normally be measured using conventional instrumentation. The circuit model is built from models of the unit operations (such as conveyors, SAG mills, cyclones, sumps, etc), and so captures the dynamic complexities and interactions of real circuit operation. CSA Mines at Cobar NSW accepted an offer to be the reference site for Mill Auto-Pilot and the system was installed in March 2004. In this application the model is used to predict mill load mass, mill solids residence time and cyclone underflow density. These parameters are used to control mill load, power and mill discharge density. The outcomes of the introduction of Mill Auto-Pilot at the CSA Mine are discussed.

Jan 1, 2004

There have been many developments in recent years in pipeline transport to enable them to be more widely used in industry. Substantial tonnages of materials that are not affected by water, such as coal and other minerals, aggregates and wastes, can be moved over considerable distances in quite small diameter pipes. Where there are no existing road or rail facilities, long-distance pipelines are usually cheaper to install, and this advantage increases in difficult terrain. Pipeline operators all over the world assert that hydraulic lines pay for themselves in a relatively short time, in spite of the heavy capital outlay, and this is equally true for lines convey-ing slurries or pastes within a plant complex.'This paper reviews some of the more important investigations in the hydraulic transport field. Although reference to systems carrying a wide range of materials is made, the majority of recent published data centres on coal transport.The paper looks at the application to a wide range of particle sizes, the development of non-aqueous slurrying media and coal/water fuels. The review also looks at some of the equipment being proposed to provide more reliable operation and in particular the range of solids-handling pumps now available.-The paper goes on to identify areas where further research and development is required and some of the many organisations undertaking this work.

Jan 1, 1985

Optimisation of mining projects is directly related to effective and efficient management of risks through the life cycle of mining projects. Effective and efficient management of risks must include explicitly all aspects of Occupational Health and Safety (OHS) through the life cycle of mining projects. This paper presents a different scale of OHS in the context of the optimisation of mining projects. Meaning of risk through the project life cycle is explained. Complex relationships between numerous risk, safety, knowledge, culture and change variables, and project life cycles are shown. The key element developed in this paper is a multi-disciplinary knowledge base that is necessary for constructive development of risk management and OHS models through the life cycle of mining projects.

Jan 1, 2003

Production scale experiment study was carried out in a limestone open-pit for testing the theory and method proposed by the author(Zou, 1987). The results of experiments indicate that the mathematical model and computer programs, which include the consideration of both the three dimentional distributions of the weak planes and the energy densities of explosion stress waves, reflect the physical process of rock bench blasting quite well. The predicted fragment distributions coincide well with the practical fragment distributions measured with the photo-image analysis method proposed by the author(Zou,1989). The paper "A Three Dimensional Mathematical Model for Calculating the Rock Fragmentation by Bench Blasting in the Open-pit"(Zou,1987), which was published in some conferences and journals, has interested some scholors and researchers. In order to test and improve the model, a group of production scale experiments were carried out in a limestone open-pit during 1986-1987. The procedure and results of the experiments are illustrated in this paper.

Jan 1, 1990

By Elber L, Whiten WJ, Cunningham KD, King GL, Bailey CW, Clay PA

The Savage River Mines concentrator treats magnetite ore at about 300 tonne/h, and produces feed for a pelletising plant. The plant incorporates two parallel grinding lines, each consisting of an autogenous mill, in closed circuit with a screen, a rougher mag- netic separator, a ball mill in closed circuit with parallel cyclones, and a finisher magnetic separator. Significant fluctuations in ore grade and grindability make it difficult to maintain pro- duct size in the narrow range desired, and to achieve maximum possible throughput at the same time, using the present largely manual control system. The present paper describes the develop- ment of a control system based on a mini- computer. It has been possible to implement a scheme of on-line estimation of product size which is sufficiently accurate for use in an automatic control system. The size estimation is essentially derived in terms of plant variables which control the ball mill cyclone cut size. Three control functions have so far been implemented and tested. These are control of the feed rate to the autogenous mill, control of water addition to the autogenous mill, and control of the ball mill sump level.

Jan 1, 1978

This paper examines the methods and people required for the evaluation of project or corporate acquisitions. Experience over the past five years has shown that some growth can be achieved by carefully evaluated acquisition of gold projects within regions where the acquiring company has gold processing facilities. Many Western Australian companies have participated in this process and the trend seems likely to continue with a diminishing number of larger producing companies controlling through joint venture or direct purchase of widely spaced ore deposits. In some cases the acquisition may include ore processing facilities, however an increasing number of smaller project acquisitions, involving small open pit gold deposits, which are within trucking distance of the acquiring company's mill. Whilst gold prices remain at the current depressed level we can expect to see this trend continue.

Jan 1, 1989

By Mahoney M

For gas content analysis in recent years, it has been standard procedure to report results on a 'dry ash free' (daf) basis, under the assumption that gas only adsorbs onto coaly material. In order to test the relationship between ash and sas content, samples of various rock types were taken from two drillholes in the Newcastle Coalfield. The results of this study confirmed the correlation between gas content and ash, providing an accurate means of relating gas contents for all carbonaceous rock types.

Jan 1, 1995

A modular computer-based monitoring system for mines is dis-cussed. The system consists of the following modules : production moni-toring system HADES, methane monitoring system CMC, seismoacoustic and seismometric systems SAK and SYLOK, communication systems. The system enables one to compose flexible,` economic structures according to the specification of a mine. Application of microcomputer-based monitoring and control systems in coal preparation plants also is discussed.

Jan 1, 1985

By Harrison J

The correct selection of equipment to use in a mine is a problem which constantly faces the mining engineer. In some cases a wide choice of equipment with different operating characteristics is available. If this equipment is to be used to assist in moving the ore it may be possible to build a computer simulation model to predict how it will perform. Typical problems that lend themselves to this type of analysis are presented. The computer models are constructed using a recent form of the GPSS computer language, namely GPSS/PC for the personal computer. This language allows the programmer to construct models in a very short time and at a low cost. Of great importance is the easy way in which it is possible to change the models to answer any of the "what if?" questions the engineer may pose.

Jan 1, 1987

By A S. Bamber

Mining is the oldest industrial practice on the planet with a history dating back over 3000 years. Since the early iron age ores have been extracted for use in a variety of contexts by humankind, from domestic to military, transport and more recently for complex industrial applications. Mineral exploration and extraction has evolved from the early exploitation of primary metal occurrences in relatively small quantities such as iron, gold, coal and copper, to the bulk mining and extraction of highly complex polymetallic oxides and sulfides today. Since the industrial revolution, mining practice has evolved substantially to support an increasing range and quantity of required metals and to accommodate the increasing scarcity of high-quality sources of these metals. A common response to the increasing scarcity of mineral resources has been to expand production through simple economies of scale, thus diluting fixed costs. This approach, however, is increasingly ineffective in the face of current trends, that include increasingly complex mineralogy, increasing pressure on environmental footprint - energy in particular, and increasing scarcity of capital for the construction of presently popular æmega-minesÆ. This paper examines historical trends and current practice in mineral exploitation in the light of the current global revolution in social, environmental and economic values as the projects move towards a vastly different topology for the industry for continued success in years to come.CITATION:Bamber, A S, 2012. The mining industry needs to be shaken and stirred, in Proceedings Narrow Vein Mining 2012 , pp 3-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By P Cundall

Three-dimensional DEM (Distinct Element Method) simulations were conducted in order to examine the performance of screw conveyors, which are installed to transport bulk materials as parts of many industrial machines, including mining and construction machinery. To apply the DEM to the analysis of screw conveyors, we added a spiral object and cylinder objects, which correspond to the helical screw, the casing pipe, and the driving shaft of a screw conveyor. These objects are represented analytically to enhance the precision and efficiency when calculating the interaction between objects and particles. Simulations were conducted for some real applications: inclined and other types of screws, as well as the basic types (horizontal and vertical). Results were compared with previous work and empirical equations. It is concluded that this method is sufficiently well-developed and useful to analyse various kinds of screw conveyors.

Jan 1, 2000

By Simpson D, Skopakow J

This paper is one of the series of papers relating to the Melbourne Underground Rail Loop and specifically describes the structural and architectural design of Museum Station. Structural arrangement, loads and design methods of the major temporary and permanent works are briefly described for the main station and entrance works. Planning of the station concourse area, booking halls and entrances are described together with the selection of finishes for all above and below ground areas.

Jan 1, 1981

By B Ilich, M Brad, R Brandli, E MarT

The Wirtgen surface miner was investigated for application to the Cloud Break iron ore deposit since it can selectively mine thin seams and there is no requirement for drilling and blasting or primary crushing as the surface miner cuts and breaks the rock to secondary cone crusher feed size. A physical metallurgical study of the surface miner run-of-mine (ROM) from Cloud Break was conducted to better understand the product size distribution, amount of -31.5 +6.3 mm lump produced, lump stability and physical metallurgical quality compared to conventional drill and blast techniques. Since the Cloud Break mine was not in production, the lump product from crushing and screening of surface miner ROM was compared with product simulations using traditional premining physical metallurgical processing techniques including drop testing of PQ diamond core. Drop test conditioning is widely used in the iron ore industry to simulate blasting, crushing and screening at the mine and subsequent product degradation during handling from mine to port to predict both the amount of lump product on ship and the size distribution of the fines and lump. The size distributions of surface miner ROM for hard, medium and friable ore types show very tight size distributions with very little above 100 - 150 mm, about 60 per cent of the distribution between 75 and 6.3 mm, with less below 1 mm compared to conventional drill and blast ROM. Crushing, screening and drop test conditioning of the surface miner ROM produced more lump in equivalent ore types compared to drill and blast techniques or their breakage simulation using PQ diamond core. The higher lump yield from the surface miner was also confirmed by pilot scale crushing of some 7400 t of surface miner ROM from the Cloud Break trial pit. The lump produced from surface miner ROM was quite stable and showed similar low degradation characteristics to lump simulated from drill and blasting techniques. Product size distribution simulations using conditioned crushed lump from 1 m diameter Bauer hole samples were found to compare well with processed PQ core samples and surface miner product from trial mining at Cloud Break. The Bauer sample method is therefore considered to be a very useful close simulation to actual lump production, although the lump yield is lower.

Jan 1, 2007

By Palmer DJ, Bain JH, Pullen JB

Over the last ten years at Risdon, zinc production capacity has almost doubled. This has resulted in modifications, many of which have affected zinc deposition operating conditions in the cells. Some of these changes appeared to have affected average current efficiency to such an extent that a special investigation was initiated, using multiple regression analysis to assess historic cell unit operating para- meters. The study highlighted the importance of certain parameters in maintaining maximum current efficiency for zinc deposition from !Risdon purified solutions under conditions of !changing current density, acidity and zinc con- centrations. Maximum current efficiency was obtained only within a zinc to acid ratio in cell electrolyte of 0.45 - 0.55 and a residual zinc concentration greater than 48 g.1-1, irrespective of actual zinc concentration or The investigation also established: ieters giving minimum power consumption at termined current density; the effect of ntration changes in common impurities on nt efficiency; the existence of high s of some impurities in solids precipit- in the cells and pure solution tanks.

Jan 1, 1975

Microorganisms have been used throughout history for the benefit of mankind with some of the earliest applications being in the production of fermented foods and beverages. Reactions involving inorganic substances such as metals, sulphur and sulphide compounds were hardly ever used until the early 1900s when it was discovered that Thiobacillus ferrooxidans was capable of promoting the oxidation of metal sulphides in ores. Today, it is widely recognised that biotechnology has great potential in the minerals industries, particularly in such areas as the leaching of low-grade ores of metals such as copper, gold and uranium; removal of heavy metal ions from process streams and from liquid process wastes; and in the desulphurisation of high-sulphur fuels. Although widespread commercialisation of mineral biotechnology has not yet been achieved, it is estimated that by the Year 2000 mineral biotechnology will have a significant impact on the minerals and metal industry and will probably account for tens of billions of dollars worth of annual production world-wide. This paper examines the actual and possible future applications of biotechnology in the minerals, metal refining and fossil-fuel processing industries. Firstly, the important chemical (and biochemical) principles involved in bio-dissolution of metals from ores and solid wastes, and in bio-accumulation of metals from process and waste solutions are reviewed, including leaching practices - past, present and future. Microbial desulphurisation of coal, and microbially-enhanced oil recovery are also discussed. The practical aspects of genetics and genetic engineering, the types and characteristics of those microorganisms important to mineral biotechnology, and the current research trends are reviewed as well. KEYWORDS: Biotechnology, microbial leaching, bioaccumulation, biosorption, bioleaching, biohydrometallurgy.

Jan 1, 1993

By R Lloyd

Coal Services (Health and Safety Trust) funded ARRB Transport Research Ltd to investigate fatigue and performance of truck drivers over consecutive shifts. The main questions were to assess: What is the most important contributor to acute fatigue in mining? Is it length of shift (eg eight hours versus 12 hours) or is it time of day (eg circadian effects)? What is the limit of successive day or night shifts before chronic fatigue affects operator performance in open cut mines? The project methodology included utilising ARRB Fatigue Monitoring Devices (forced-choice stimulus reaction) in eight haul trucks, testing 24 subjects over several weeks. Each subject filled in a Fatigue Risk Questionnaire on lifestyle and health. Operators worked a 14-night, one day off, 13-day roster of 12-hour shifts in a fly-in/fly-out operation with excellent opportunities for restorative sleep between shifts. A total of 3500 hours of real-time data was collected, representing the first set of objective, real-time driver performance data for Australian mining. The data showed that for a single night of driving haul trucks, there appears to be no effect on operator fatigue from the amount of time on task (for the 12 hours). In fact performance was worse through the first eight hours than the last four. The circadian influence had a stronger affect than working more than eight hours. Of the 14 nights worked at the site, nights 13, 14, seven and two respectively, were the worst. This presents a conundrum for policy makers who may like to place caps on working hours or rosters in the hope that it will alleviate the fatigue issue. It will not. The major finding within this study is the combined influence of circadian rhythms (human body clock) and individual variability on performance. The lifestyle habits and the health of individuals have a profound effect on operator performance as shown by the strong positive correlation between high fatigue risk scores from the Fatigue Risk Questionnaire and poor performance. An individualistic approach would appear to have the best chance of reducing high potential incidents due to fatigue through successive nightshifts.

Jan 1, 2005

A case study of a landslide, which threatened vital infrastructure essential for the continuous operation of the Ok Tedi copper mine is presented. The paper presents a detailed description of the land- slide, outlines the assets at risk, and how the issue was addressed. This included the consideration of remedial options and the im- plementation of the most economically sound and geotechnically feasible remedial design which was completed within budget and on schedule. The paper is intended to highlight the responsibility of a mine based Geotechnical Engineering section in providing essential geotechnical investigations, design and professional advice on addressing stability issues in the infrastructure region.

Jan 1, 1997

By Li G, Dean-Jones G. L, She T

Highwall mining is a specialised and largely automated mining method developed in the United States for the extraction of coal left under a shallow overburden cover after cessation of economical open cut mining operations. As the name indicates, coal is extracted from the seam exposed along a highwall by a remotely controlled continuous miner operating in a single unsupported opening and brought to the surface by a string of conveyor segments. The single entries are separated by coal .pillars and driven normal to the highwall, over areas where the thickness of cover and volume of recoverable coal is insufficient to allow or justify conventional underground mining. An additional highwall mining method is augering. The success of high wall mining operations depends significantly on geological features, notably the stability of the working roof, determined by the type and mechanical properties of the immediate roof strata. Stability of the ribs, absence of floor heave, faults and dykes are further important prerequisites for profitable highwall mining. The geometric relationship between the spatial attitudes of existing joint systems, the direction (azimuth) of the single entry opening and its vertical profile determine the unimpeded depth of penetration into the coal and thus its economic success. The mechanical implications of the lithological transition zone from a coal seam to either primary or original roof strata, compared to an interface between the coal seam and overlying strata, characterised by a sharp erosional boundary between coal and a secondary immediate roof stratum, are very significant. The compatibility between the response to mining by the geological system (floor-seam-roof) and the capability of the mining equipment to prevent the development of instability are essential requirements from a mechanical viewpoint. The minimisation of vibrations, very good horizon control, an ability to vary the profile of the opening, and the maintenance of consistently high advance and retreat rates, are also important aspects of profitable highwall mining.

Jan 1, 1995