Search Documents

By D S. Stewart, K W. Keskimaki

In 1999, the Henderson Mine commissioned the Henderson 2000 project - a new truck haulage level, a new underground crusher and a 24 kilometre conveyor system to replace a 23-year old rail haulage system. Henderson has been able to continuously improve in almost all aspects of its rubber-tired mining. The rail haulage system represented one of the last barriers to continuous improvement to the overall plant performance. Many of the lessons learned in other areas of the mine were utilised to design the truck level. This paper chronicles the benchmarking, equipment selection and design of the level. Areas covered will include haulage trucks, level layout, ore chute design, traffic control, road design and crusher layout.

Jan 1, 2000

By Jankola W. A, Delong O. J

Historically, the silica content of zinc concentrates treated at Cominco's Trail Operations has been low. Silica in the roaster calcine seldom exceeded 1.5 per cent because of the low silica content of concentrate from Cominco's Pine Point mine. With the shutdown of Pine Point, alternate sources of concentrate were required and it was anticipated that calcines containing greater than two per cent silica (with excursions above three per cent) would have to be treated. Previous experience indicated that the existing leaching circuit could not tolerate such high levels. Therefore, a research program was undertaken to identify the key factors affecting silica precipitation; to compare different process alternatives; and to make recommendations for modifications to the existing plant. A project to modify and upgrade the leaching circuit has now been completed. Calcines with higher silica contents are successfully treated, but the upper limit of the circuit is unknown. The results of the research work will be discussed and the new leaching plant will be described. Recent operating results will also be presented.

Jan 1, 1993

Increasing attention is being focussed worldwide on the strategic environmental assessment of mining projects, including consideration of cumulative environmental effects. In New Zealand there is now an end in sight for inappropriate delays in resource consent approval of responsible mining projects. This paper investigates six case examples of recently consented mining and quarrying projects, whose applications were notified. It also explores the nature of delays that occurred, the factors that contributed to the delays, and whether the consent process delivered fair and effective public participation and desirable environmental outcomes.

Jan 1, 2005

By Weyer J

Many existing computer planning programs for the mining industry focus either on big mining enterprises with a high production rate or on smaller operations for high value minerals. Big mining enterprises, like the hardcoal company `Ruhrkohle AG' in Germany have their own R&D departments which develop powerful computer programs for planning purposes, partly in co-operation with mining universities. However, there is a remarkable number of small- scale mining operations which are either not able to buy expensive hard- and software or don't have the skills for the operation of extensive software programs. Partly there is also a trend in using rule of thumb calculations rather than computer programs which need a lot of - partly unavailable - data. For this reason a computer program was developed which does not need expensive hardware and software and which can help the planning engineer in the selection of a limited number of possibilities. Until this time the planning engineer established two or three different cases and calculated the results with a pocket calculator. This could last some hours or even some days. Now he or she can use the computer program with a normal PC to compare the cases. All activities are menu-driven. The basis for all, calculations are fixed and variable costs as well as average performance for special activities. The paper gives an example for a possible planning situation in fluorspar mining (originally this program was developed for the fluorspar enterprise Lengenfeld in Germany). It shows the initial situation, the main structure of the program, the input logic and the results. Benefits, limits and possible extensions of the program are discussed.

Jan 1, 1995

By N Harries

The management of risks associated with slope instability is an essential process in the safe and economic operation of open cut mines. The æslope stability radarÆ (SSR) has been developed to better manage those risks. The SSR can remotely scan a rock slope to continuously measure any movement of the face. The system can detect and alert users of wall movements with submillimetre precision. The high level of movement precision and broad area coverage of the rock face can allow for a better understanding of the geomechanics of slope deformation, including magnitude of potential failures and additional warning time of impending instability. Additionally, radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. SSR systems have been deployed in many mines in Australia, Indonesia, Africa, Chile and the United States. Greater than 100 rock falls and waste dump failures (from several tonnes to millions of tonnes) have been monitored, and on every occasion precursor æwarningÆ movements were recorded by the SSR. This technology enables a radical change in the management of risks in open cut mining. This paper presents recent case studies of how the SSR technology has provided safety and productivity benefits to large open cut metalliferous mines.

Jan 1, 2007

By T Martin, M Martin

Mining of sulfide-based ore deposits typically creates a potential for release sulfate and acid to groundwater, and many operating mines are thus predicted to require long-term post-closure treatment of groundwater. Toward the goal of selecting an optimal treatment, this paper compares costs of four demonstrated technologies for long-term treatment of sulfate-contaminated groundwater: in situ biological reduction (ISR), in situ permeable reactive barrier (PRB) composed of compost and zero-valent iron (ZVI), and two ex situ æpump-and-treatÆ technologies ù ex situ biological reduction, and ex situ nanofiltration with lime precipitation. Costs for each technology are estimated for treatment of a model aquifer system containing sulfate-contaminated groundwater, with the goal of treating 1 m3/min of groundwater from 1500 mg/L sulfate to a target level of 500 mg/L. (Metal removal is typically achieved by these technologies, and thus excluded from this analysis.) Costs are estimated for each technology as a function of treatment duration (ten to 60 years) and, for PRB and ISR, required replacement frequency (ten to 60 years). Estimated costs include capital and operation and maintenance, using a seven per cent net discount rate. Results indicate that ex situ technologies (biological reduction and nanofiltration with lime precipitation) are the most expensive. In situ technologies may be much less expensive, with PRBs having by far the lowest potential cost, followed by ISR as the next least expensive. However, actual costs for the in situ technologies are very sensitive to poorly constrained parameters, particularly the ZVI content of the PRB, and the effective life of PRB and ISR systems. This large cost uncertainty supports delaying remedial actions where viable, and suggests that feasibility analyses are generally warranted for specific applications to focus on these sources of uncertainty.

Jan 1, 2003

Iron from the blast furnace constitutes the starting point in steel production and any increase that can be made in iron production will bring about important repercussions in a long line of processes. Coke constitutes a major item in furnace operation and consumption at the Port Kembla Works of Australian Iron & Steel Ltd. has been approximately 1,850 lb. per ton of iron produced on ore practice, or 3,000 tons per day.For many years coke quality has been subject to much criticism by furnace operators throughout the world, sometimes with little real grounds. Whatever the merits of previous arguments, and they were no doubt two-sided, the development of bigger furnaces has focused attention on coke strength. At the same time a decrease in the quantity of good quality coking coals available to many plants has stimulated research in this field.Extensive coke research has been carried out overseas, and in Australia the.B.H.P. Organization is now actively doing likewise in its Central Research Laboratories at Shortland near Newcastle, N.S.W., and works research groups at Newcastle and Port Kembla Steelworks. Similar work has been initiated in the beehive coking industry. Such work is in its infancy and this paper will outline the direction of the activities at Port Kembla rather than propound specific solutions.At Port Kembla good quality coking coals are readily available from the IIIawarra coalfield. The seams generally mined for coking are Bulli and Wongawilli and to a much smaller extent Tongarra. Characteristics of these coals appear in Table 1.

Jan 1, 1958

By L Rattmann, T Katz, J B. Pateiro-Fernßndez

Carbon capture and storage (CCS) is expected to become one of the main technological instruments for mid-term reduction of CO2 emissions into the earthÆs atmosphere. Besides the reduction of CO2 emissions into the atmosphere, the implementation of CCS would have various negative consequences, which are û if at all û only poorly covered in the current socio-political discussion. Taking into account all aspects of CCS, the outcome of a comprehensive and conclusive assessment of CCS against the background of the sustainable development concept is uncertain. When assessing the overall impact of CCS in a holistic approach, a variety of aspects with effects on sustainable development are affected. Besides economic issues, various other effects of implementing CCS should be taken into consideration. These include for example additional costs for CCS facilities and processes and a decrease in powerplant efficiency due to high energy requirements of capture processes, and various ecological and societal aspects, such as higher demand for combustible, resulting in faster depletion of reserves and higher land and water use and the provision of jobs along CCS technology chain. This paper presents an approach for a structured sustainability assessment of CCS based on the multi attribute decision-making (MADM) method analytical hierarchy process (AHP). The functioning of the presented methodology is exemplified at the case study of a German coal fired powerplant.

Jan 1, 2009

By Sullivan TD, Redman PG

AND INTRODUCTION The Lochiel coal deposit, a large Tertiary soft brown coal deposit in the mid north of South Australia, is currently being investigated by the Electricity Trust of South Australia (ETSA) as a potential source of fuel for a base load power station. Feasibility studies indicated that the proposed dragline method of overburden removal was viable but economically sensitive to both highwail and dump batter angles. The unusual properties of the unconsolidated overburden sediments and the groundwater regime posed a number of intimately related hydrogeological and geotechnical questions which were addressed before and during the excavation of a trial pit. All strata at Lochiel are of soil strength, and artesian aquifers occur above and below the coal. From the initial evaluation of the deposit a number of hydrogeological questions were defined. These related to the rate at which the pore pressure in the silts is reduced by dewatering, the extent of the reduction in pore pressure due to prestripping, and the feasibility of dewatering and depressurising carbonaceous silty sand sequences. The site of the trial pit was selected to answer these and other questions from the basis of a detailed geological, hydrogeological and geotechnical understanding. The trial pit dewatering system simulated a full scale mine dewatering system and included ten pumped wells, twenty drainage wells, and nearly 400 monitoring instruments. It operated from September 1986 to June 1987. The excavation was carried out between February and May 1987.

Jan 1, 1988

By Borsaru M, Wylie AW

A neutron irradiation technique has been developed which is suitable for the determinat- ion of the iron and aluminium content of iron ore fines (-6 mm particle size) on a moving rubber conveyor belt. The determination of iron entails measure- ment with a NaI(Tl) gamma ray detector of the characteristic prompt gamma rays (7.64 MeV) due to thermal neutron capture in iron, while the determination of aluminium is based on thermal neutron activation analysis. For the latter a second detector must be placed down- stream to monitor the 1.78 MeV gamma radiation emitted after activation of aluminium. Although conveyor speed has no effect on the Fe measurement, it has an adverse influence on the aluminium signal, and the belt speed should not exceed 0.1 m/s if good accuracy is required. Static trials on a 460 mm rubber conveyor belt with constant ore geometry indicate that for iron an accuracy of ¦ 1.2% Fe (2a) can be achieved for crushed run-of-mine ore at

Jan 1, 1978

By G S. Esterhuizen, M M. Murphy, T S. Bajpayee

The strength reduction method (SRM) has been implemented in the FLAC3D finite difference software and applied to coalmine entry support evaluations. The FLAC3D numerical models have been calibrated against instrumented field sites in varying geologies, depths and field stress conditions. The calibration between the field and model results obtained a satisfactory match for rock deformation and support response. Previous research has also developed good correlations between numerical model stability estimations using the SRM and empirically derived stability estimations using the analysis of roof bolt systems (ARBS) software and the coalmine roof rating (CMRR). The purpose of this paper is to further apply the SRM to investigate how specific geotechnical and support parameters can impact coalmine entry stability. Results from different studies demonstrate how the calibrated models were used to investigate a few of the well-known questions in both mine design and support design. For mine design the impact of strong and weak beds in the roof strata, rotating the principal stresses and weakening the floor on excavation stability is investigated. For support design the impact of support length, support spacing and adding cable bolts to the design is demonstrated. These scenarios are evaluated in developmental coalmine entries for a variety of geology and field stress conditions. Stability factors are calculated for each scenario using the SRM. The SRM allows the impact of each parameter to be quantified and allows the support system to be optimised for given geotechnical conditions.CITATION:Esterhuizen, G S, Murphy, M M and Bajpayee, T S, 2014. Analysis of geotechnical and support parameters on coalmine entry stability using the strength reduction method, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 383–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

Having worked as a consultant for most of his 40-year working life, mostly as a mineral property valuer, the author has seen many poor valuations. Most were valuations of exploration tenements where the selection of the rather subjective, but necessary, geological inputs raised the main concerns. Those valuations involving iron ore prospects raise particular problems due to the special characteristics of such deposits. Iron ore is more like an industrial mineral rather than precious or base metals and Reserves are determined not by a traditional cut-off grade but by customer specifications. This is intended to be an overview/keynote paper on the current state of the growing (yet consolidating) Australian Iron Ore industry. It has now moved beyond Western AustraliaÆs æPilbara Big TwoÆ of Rio/BHPB (with the emergence of the irrepressible FMG and Hancock Prospecting) to include the YilgarnÆs æMidwest ManyÆ (including US re-entrant Cleveland Cliffs through Portman) and projects in other States. Ore types have moved from haematite Brockman to martite-goethite Marra Mamba (including the RobeÆs mesas and below water table Yandicoogina CIDs) and magnetite ore types. There are DSOs and secondary process feed. Mineral valuers have to reflect today upon these and many other determinants of value when choosing the most appropriate methodologies to adopt when technically assessing and valuing exploration tenements containing iron ore. Set against a frame work of the JORC Code (2004) and VALMIN Code (2005), the general valuation issues involved in using the cost methods (eg multiple of exploration expenditure), market methods (eg comparable sales, rules-of-thumb and joint venture terms) and income methods (eg synthetic discounted cash flow (DCF)/net present value (NPV) modelling) are discussed. Relevant factors when valuing iron ore properties are discussed, eg ore type, lump/fines ratio, stripping ratio, water table, impurities and grade, particularly the JORC confidence category of the identified mineralisation. Remoteness and access to existing rail infrastructure is a key consideration.

Jan 1, 2007

The Directional Drill Monitor (DDM) is an advanced instrument for real time in hole surveying. It was developed by Du Pont (Australia) to suit Australian gassy coal mining conditions. The instrument consists of three units: i. Down hole transmitter ii. Acoustic transducer iii. Data receiver processor unit (i.e. up hole unit). This paper describes the function of each unit in detail and highlights the importance of the DDM in long hole drilling efficiency. Surveying is carried out independent of hole depth. Each survey takes 2-3 minutes to complete, the frequency of surveying to control borehole trajectory is determined by the accuracy required for a particular hole.

Jan 1, 1992

By Hutton W

The Argyle Diamond Mine is the first significant diamond producer in Australia. The project has been developed with new concepts in circuit design, process control technology, organisational development and training. After its first year of operation, the Argyle Heavy Medium Separation Plant has proven extremely efficient in recovering diamonds. Apart from cyclone wear, no major problems have been encountered. Ferrosilicon consumption is well below the design level which is a reflection of the sound design of the medium circuit. An Audit Plant continuously monitors the Heavy Medium Separation Plant tailings for diamond loss.

Jan 1, 1987

China has large amounts of iron ore reserves, but iron ore in China, with low-grade, small disseminated particles and many other associated minerals, is difficult to dress. In recent years, with the fast development of China's steel industry, the demand for iron ore has increased markedly. The new technologies in iron ore dressing in China are very effective in processing haematite and other difficult to dress iron ores. The iron ore grade and recovery rate has been improved. This result alleviates the difficulty in iron ore supply in China.

Jan 1, 2007

By Waddell S

A new procedure has been developed for the direct determination of metals loaded on activated carbon. It involves preparation of a suspension of the powdered carbon in water, followed by direct sampling of the suspension with a micropipette,and analyses by atomic absorption spectroscopy using carbon rod atomization. Advantages of the method include the simplicity of sample preparation and the ability to provide a complete metal analysis in 1 - 2 hours. This enables carbon-in-pulp operators to respond quickly to changes in plant efficiency arising from carbon fouling. The successful application of the method has been demonstrated for gold, copper, nickel and iron. Other elements to be surveyed include calcium, magnesium and silicon.

Jan 1, 1984

By B Wiggins, M Russell

Off-gas handling systems are a critical component of modern metallurgical furnaces and typically represent as much as 50 per cent of the total installed smelter capital cost. Inadequate off-gas system performance, due to insufficient exhaust flow or excess maintenance downtime, can present a serious process bottleneck and limit smelter production rate. Therefore, it is essential that the relevant performance issues are fully understood and considered in the design of these systems, particularly when combustibles produced within the furnace must be combusted or handled in the off-gas system. This paper examines the requirements, design issues, and conceptual design process for state-of-the-art postcombustion off-gas systems. The relevant design considerations of safety, environment, energy consumption, and maintenance are presented, and the relative importance of these key issues are compared and discussed. The benefits of using computational fluid dynamic (CFD) modeling in the design process at the conceptual design stage are also demonstrated. Finally, the design basis and performance of a recent Hatch-engineered system currently in operation is evaluated.

Jan 1, 2002

By E Widzyk-Capehart

The conventional ammonium nitrate fuel oil (ANFO) loader utilises a pneumatic system to control the flow of ANFO (via rotary actuator/ball valve) and air (via an auxiliary air valve). This system, though relatively simple and reliable, has several drawbacks with respect to ease of control and level of automation. In this paper, a radio frequency (RF) remote control for explosives charging is discussed. The system design incorporates electric solenoid valves to control the rotary actuator and the auxiliary air valve. All operations associated with explosives charging are selectable at the remote and are completed according to a modifiable time sequence. This allows the following charging sequence to be reduced to a single momentary application of the remote:removal of water from the hole prior to charging with ANFO; charging of the hole for a preset but adjustable period of time; and removal of the remaining ANFO from the ANFO hose. A specially developed remote switch allows the operator to maintain two-handed control of the ANFO hose whilst achieving full control of the charge-up process. Failsafe electronic architecture is incorporated into the systemÆs design to increase safety to the highest level. Should the RF remote control fail, a wired remote is included in the system to allow for the charging process to continue, albeit at a reduced level of control. The application of the RF remote control system in an underground explosives charging operation minimises and/or eliminates many problems associated with the use of the conventional charging system. These include: the wet-hole problem, trip and entanglement hazards, air embolism and the two-man loader control requirement. The developed remote control unit proved to be effective at removing water from wet holes leading to increased face advance per drilling operation. It proved to be economically feasible, allowed for an increase in systemÆs dependability and safety factor and for a truly one-man operation which resulted in reduced manpower.

Jan 1, 1999

By K Kellett, A V. Metzner

From its discovery in 1845 ion exchange has continually improved technically to an extent where it is now in wide use commercially in many industries including mining and environmental. Purity Systems Inc. (PSI) has made advances in the development of metals capture materials such that metals recovery using the PSI patented technology is now a viable economic process for many previously rejected applications. PSI, in conjunction with Ammtec Limited, have developed cost effective advanced processes and systems.The presentation will introduce the chemistry behind the materials and its relevance to the chelation and ion exchange methods. The applicability of the PSI resin technology to copper, cobalt and nickel recovery and the engineered systems options available will be discussed as well as piloting at Titan Resources NL Radio Hill mine at Karratha in Western Australia.

Jan 1, 2002

By Massy-Greene RB

Limited recourse financing techniques reduce the financial exposure of equity holders to major mining projects by transfering some of the risks to the banks which provide loan funds for project development. This can only be achieved by a clear understanding of the principles involved. Engineering and management decisions on how the resource is to be developed and extracted must be made in the light of lender's requirements. The structure of sales contracts, joint venture agreements and many other documents can be important in limited recourse financing. If projections show that the debt can be repaid from project cash flow, loan agreements and other arrangements can restrict lenders ability to look to the equity holders for repayment of project loans.

Jan 1, 1981