Search Documents

By Inoue T, Takahashi N

To construct the accessing railroad line to the northern portal of Seikan Undersea Tunnel, nine tunnels amounting 7.4km in their total length were excavated through soft mudstones of young- er tertiary era with use of smaller-sized mechanic al excavators. Rocks were classified in four classes to which the tunnel support was designed respectively. Of several combinations of driving equipments stu- died comparatively, the method using the mechani- cal excavators was estimated to be the best choi- ce. The efficiency of the excavator was traced in every construction section and the data colle- cted was reviewed numerically. The result showed that the efficiency of the excavator dropped wh- ere the rocks were as hard as over 200kg/crif for compressive strength. And a few technigues in tunnelling i.e. contr- olling dusts in shotcreting, lattice arch, evaluati- ng measured deformations were tested and review- ed too.

Jan 1, 1987

This paper discusses design concepts in planning a large modern bulk terminal. The need is emphasised for a studied master plan, in-built materials handling flexibility and staged development. An integrated approach is advocated, combining functional purpose designed foundations and structures to serve their mechanical, electrical and environmental functions. Dry bulk and slurry handling are also compared in perspective.

Jan 1, 1983

Some of the major factors affecting ore reserve estimation in gold mines are discussed together with their impact on computational methods.The major priority in ore reserve estimation is to get sampling and geological problems resolved. Poor basic information cannot be remedied by mathematical methods.Generally the more complex a deposit becomes the greater the need for subjective assessment and the less applicable are more complex ore reserve methodologies.

Jan 1, 1984

There is very little in Australian mining law that sets out the rights of mining tenement and exploration licence holders as against other parties who wish to carry out ground or aerial surveillance over those areas.There have already been several legal actions arising out of this lack, and more can be expected as the public places more rigorous constraints on corporate and individual behaviour. Field personnel, who are mainly fairly junior and less experienced, are entitled to some guidance from the minerals industry, guidance which up to now appears to have been either lacking or covering such a wide range of standards from corporation to corporation as to be virtually useless.Because each State writes its own laws there is no consistency, and the laws generally are lagging behind developments in the industry. In particular, the practice of granting mining tenements for sporadic exploration, a practice that is a leftover from much earlier mining law, has dotted the Australian continent with unattended and unmarked or poorly marked tenements that are difficult to find but confer on the holder prior rights to the minerals under them. Entry onto those areas in most jurisdictions is an offence and their existence compromises the efforts of regional explorers.This clearly unsatisfactory situation requires remedying, which is the purpose of these proposals. A more systematic approach to the granting of reconnaissance, regional and detailed exploration, mining, and retention rights will eliminate much of the problem. For the rest, a code of practice needs to be adopted as soon as possible.

Jan 1, 1996

By B Sno, P A. Cockburn, R C. West, C U. Jones

Clyde Materials Handling (CMH) and WorleyParsons have developed a concept for a flash furnace feed system using the specialist pneumatic conveying equipment expertise of CMH and the flash furnace process experience of WorleyParsons. CMH has developed a proprietary volumetric feeder (called a Rotofeed), which is extremely accurate and overcomes many of the problems inherent with loss-in-weight screw feeders and drag chain conveyors, previously regarded as state-of-the-art. Initial indications are that the Clyde-WorleyParsons feed system could deliver the following benefits to flash furnace operation: accurate pulseless delivery of feed material to the head of the burner leading to improved combustion performance and process stability; highly accurate split to the individual quadrants of a conventional burner tube, or provision of a smooth hollow curtain to a burner without guide vanes; decreased pressure pulsation in the furnace due to improved combustion control and performance; and decreased temperature fluctuations in the furnace due to improved combustion characteristics and hence reductions in refractory thermal stress and wear.

Jan 1, 2005

By Torres F, Cerda I, Gimenez P, Gonzalez G, Castelli L

Slurry density measurement, specially in cyclone feed streams, is fundamental to grinding circuit control. With the purpose of increasing the availability of such a measurement, the design of a soft-sensor in an actual grinding plant is addressed in this paper. The system is designed to substitute the momentary unavailability of the real density sensor, either because it has failed or because it has been removed for any other reason. The ARMAX model structure is determined using the stepwise regression method. Starting with a list of the candidate variables, the method selects, one by one, and in a systematic manner the variables which best model the measurement to be replaced, choosing them from the set of presumably correlated candidate variables. In this paper not only the single measurements are included in the list of candidates, but also combinations of such measurements having physical significance. A phenomenological model has been built with the purpose of determining these combinations. It turned out that in most of the cases the components of combined measurements having physical significance were selected by the stepwise regression method, instead of the single measurements. Actual grinding plant data is used to determine the model structure, to estimate the model parameters and to test the predictive capability of the developed soft-sensors. Good results are shown to be obtained during periods of up to 30 hours of the density soft-sensor operation.

Jan 1, 1995

By Randall C

Energy studies have been undertaken at a number of open coal mines in the Hunter valley. A range of energy efficiency benchmarks and targets have been established, which, when applied across coal mines, will assist in leading to a significant improvement in energy efficiency in the coal mining industry in NSW, thereby leading to an improvement in environmental performance. Typically, energy efficiency improvements of 20 per cent and higher appear possible at many mines leading to a commensurate reduction in this controllable operating cost, ie energy. On the basis that annual energy costs and net profit are similar for many mines, a reduction in energy costs by 20 per cent will lead to increase of 20 per cent in net profit.

Jan 1, 1995

A generalised mathematical model for hydrocyclone classifiers was developed by the author (Nageswararao, 1978) using dimensionless groups which include phenomenological characteristics as independent variables. This model is incorporated in JKSimMet, the steady state mineral processing simulator developed by JKTech.Recently, when this model was rewritten (Lynch and Morrell, 1992), in terms of variables other than those used by the author, a few errors have crept in. For example, while the exponent of (Du/Dc) in the equation for d50e should be negative (-0.47), it was recorded as positive (0.47). Also, the exponent of (DoIDe) in the equation for pressure drop should be 0.67 and not 0.60. In the same equation, the exponent of Dc would turn out to be -0.10 and not 0.15. These are clearly attributable to typographic and rounding off errors, while transforming the original equations.More recently, Cilliers (pers comm) has done a comprehensive evaluation of the major semi-empirical models for hydrocyclones.He observed that the major difference between the cyclone model developed by the author and other models lies in the method of quantifying the effect of spigot diameter on d50e. He noted that while all other models predict an increase in d50e with a decrease in the spigot diameter, the model as cited by Lynch and Morrell (1992) predicts just the opposite. However, he conjectured correctly that the discrepancy could be due to a typographic error. As the model is still unpublished, it is felt that the original model equations should be recorded with the correct exponents, so that errors in predictions other than those due to the limitations of the model itself could be avoided. They are given hereunder.

Jan 1, 1995

Future depth and production limitations of an ore hoisting system are fixed by its initial design criteria. There is little scope to extend these limitations once installation is completed. Depth and production rate upgrades from the initial duty to the hoistÆs practical limitations require capital expenditure in stages, each of which can be defined when assessing the initial system design criteria. A means of presenting and assessing the design criteria, the limiting factors in each option and the relative present and future capital costs is necessary to arrive at a solution that delivers the best value to the mine. Application of this technique to recent friction winder installations and upgrades in the Australian mining industry is of particular interest; however, the analysis methods are also applicable to drum hoists. It is usual to specify a minimum hoisting capacity and depth, based on mine ore handling design and production needs. The final hoist depth and production rate are usually a result of the initial hoist design and hence it is useful from the outset to specify a required production versus depth envelope for the mine. Technical solutions can then be modelled within this envelope at their initial and final duties and a comparative analysis made against the cost of installing and progressively upgrading each solution. Understanding the factors that constrain each solution to a maximum production rate at a given depth is important, as the costs of overcoming limiting parameters such as rope tread pressure and motor power can be significant. The task of understanding and evaluating the options open to the hoisting system designer is simplified using this approach. Communicating the results of a multi-dimensional problem such as hoist specification is also made easier using the graphical methods inherent in the analysis.

Jan 1, 2005

The purposes of defining the mining environment for underground mass mining and the uses of characterisation data are outlined. The requirements for data in the areas of geology, surface and groundwater hydrology, topography and environmental constraints and geotechnical studies are identified. Emphasis is then placed on the collection and interpretation of geotechnical data for establishing the in situ stress regime and for rock mass characterisation. Methods used for diamond drilling, core logging, borehole logging, data analysis and presentation, rock mass modelling and rock mass classification are outlined. Finally, recent and potential advances in the state-of-the-art are identified in areas such as geophysical methods, measurement while drilling, computerised data collection and analysis, rock mass modelling, in situ stress measurement data presentation and interpretation, and some applications of rock mass characterisation data.

Jan 1, 2000

By R E. Hobbs, O Grabandt, C Das

Mine hoisting is carried out from depths of up to 4 km. At extreme depths, the ropes are so heavy that a large part of their capacity is employed in lifting themselves. Consequently, deep mines have an intermediate winding station. Even at lesser depths, the weight of steel wire rope reduces the possible payload. Of course, steel wire ropes have, over the years, demonstrated exceptional reliability and acceptable lifetimes. The use of steel is supported by well established operating rules and sound NDT methods. However, lightweight ropes made from synthetic fibres could be of great benefit to the industry, with the prospect of eliminating two-stage winding and substantially increasing the payload. Initial tests, in cycling over sheaves, have demonstrated that an aramid co-polymer fibre, Technora« is a potential candidate for this type of service. This paper presents results of testing carried out on aramid co-polymer and other synthetic fibre ropes. These results hold out the prospect of exceptionally long lives. Possible NDT methods are explored including optical fibres with optical time domain reflectometry or with Brillouin scattering, plus a method based on carbon fibre continuity. The introduction of aramid co-polymer ropes will require extensive testing and a program is proposed in the format of a Joint Industry Project.

Jan 1, 2005

By Shibata Y, Shimizu R, Fukushima A

Kobe is divided by the Rokko Mountains, runn- ing from east to west. The southern section of Kobe is highly developed in contrast with the northern section, but big, new residential pro- jects like the Hokusetsu New Town and Hokushin New Town are steadily being developed. To handle future traffic between the two sections of the city, the double-tracked Hokushin Line, now under construction, will connect the Shin Kobe Station of the Kobe Municipal Transit (Kobe's subway system) to the Tanigami Station of the Kobe Electric Railway. The locations of Kobe city and Hokushin Line are shown in Fig.-1 and Fig.-2 respectively.

Jan 1, 1987

By P Cheluszka, M Jaszczuk, P Sobota

This paper refers to a new idea of stereometry of cutting drums of longwall shearers designed to get medium and hard to mine coals. A new way to place picks on a drum enables to readjust a number of picks being in contact with the body of coal to shearer haulage speed. Owing to this a remarkable increase in depth of a cut within the low range of haulage speed has been obtained. On comparing operating characteristics a considerable reduction in the specific energy consumption has been shown when using the units machined as per the new idea, in comparison with the units produced in series.

Jan 1, 2003

By B, J Bianchini, N Voermann, C Crowe

Operational and economic imperatives in the metallurgical industry have led to numerous advancements in furnace design. Modern furnaces provide high production rates, high percentage online time, long campaign life between rebuilds and safe operating conditions. Current trends for maximising plant efficiency include increasing the throughput of existing process vessels (often by a factor of two or more) and the use of newer, highly intense processes. In both instances, the process intensity results in the generation of higher heat fluxes to the crucible walls. High-intensity furnace operation with the objectives mentioned above has become possible with the following furnace design features: Strong sidewall cooling systems, using copper coolers, to accommodate the high heat fluxes encountered while protecting the crucible refractories; Robust, spring-loaded furnace horizontal and vertical binding systems which maintain tight brick joints through-out all stages of operation; and Well-designed, intensely cooled tapholes for metal, matte and slag. The integration of these features along with properly selected refractories, appropriate instrumentation systems and efficient water-cooling systems is also highly critical. These design features have been successfully implemented in electric smelting furnaces, flash smelting and converting furnaces (Outokumpu and INCO types) and lance injection furnaces (Mitsubishi, Ausmelt and Isasmelt types). This paper will discuss design aspects and operating results for several installations.

Jan 1, 2002

The complete life cycle of a production facility has many phases requiring many different skills and many different personalities. It is not unlike the life cycle of a person and many parallels can be drawn from it. I leave some of these analogous situations to your fertile minds. The author, having worked in operations, plant design, plant commissioning, marketing and many other interesting situations through the industry has drawn from this experience and examples given by many associates in the industry.The phases seen are as follows: Concept Studies û someone has a bright idea of how to make a dollar. Scope Studies û what possible processes/options that could make a dollar. Prefeasibility Study û the æviableÆ scope options are studied to develop feasible options. Feasibility study û defines the concepts that should be designed to make a viable project thus enabling financing and project commitment to be made. Detailed Design û an intermediate step that consolidates the inputs to give a robust plant that can be constructed.Construction û people can see what they thought was going to occur and start to understand the plant. Commissioning û the hand-over of æownershipÆ from the conceiverÆs to the operators. Operations û the ætoyÆ has become reality and money must be made. De-commissioning û the plant has seen out the useful life of the ore deposit, it now goes through a further process required by society.Across these phases of plant design run several countervailing management requirements that can influence the outcome of the plant design. Some of the management rigours that have to be applied to the various phases are as follows: costing basis of the various phases; operational and maintenance reviews; sustainable development; risk assessment; reliability reviews; equipment availability; commissioning time; and environmental review.This paper endeavours to awaken people to the phases that projects require for a successful outcome and the management rigour that has to be applied throughout the phases to ensure the correct intellectual horsepower is applied at the right time to ensure the best outcome.Many of you would be parents and realise this is not unlike the development of children, teenagers, adults, retirees and ongoing.

Jan 1, 2002

By P N. Martens

In the course of the development of the Report of the World Commission on Environment and Development (WCED) in the 1980s an expression was introduced in the public discussion on environment and development that influenced the international and national policies of the last 20 years in all areas: sustainable development. The UN decided in 1992 to implement a program with the Agenda 21 which contains the demand for developing indicators for sustainable development. In this context an indicator is understood as a quantitative or qualitative measure that can be measured or described throughout time and which moreover is able to depict the current status and changes. In order to enable for a simple holistic assessment of sustainable development, highly aggregated indicators are required, which integrate the criteria identified as relevant within a framework to be defined. In the presented paper, sustainability indicators for the mining industry are developed that account for the allowances of the sustainable development concept and the Agenda 21. The indicators are quantifiable and traceable through time so that developments can be traced and assessed. Furthermore, the indicators account for the multidimensional aspect of sustainable development. They are designed to allow for the integration of several dimensions in one indicator. The premises that are underlying the development of the indicators are the minimisation of negative impacts on the environment and society while simultaneously considering the maximisation of social and economic factors. Moreover, the participative momentum that is part of the sustainability idea is safeguarded in explicitly integrating the social acceptance of certain measures into the assessment. The indicators presented are based on the logical combination of statements through the use of Boolean algebra. Starting with basic statements for which the logical value is oriented on the sustainability paradigm, complex multidimensional statements can be constructed and assessed.  

Jan 1, 2009

Australia had been enjoying a market boom led by the mining sector and West Australian mines were leading the way to satisfy the massive demand for our natural resources, especially from China. However, the Apache gas explosion on Varanus Island, 97 km off the west coast, has clearly demonstrated how the unexpected can suddenly impact on profitability and investor confidence for the mining industry. Risk management with contingency planning can provide the most cost-effective solution to help ensure mining projects are successful. For this discussion we will focus primarily on contingency planning, CP for mining projects à and how to plan for the unexpected. The Apache gas explosion will be our example æUnexpected EventÆ. Insurance may provide financial compensation but it will not protect your reputation as a reliable supplier or prevent damage to investor confidence and future mine projects. However, contingency planning can provide real protection for mining projects à to survive the unexpected.

Jan 1, 2009

By Woodcock J. T, Rummel P. H, Sparrow G. J, MacRae C. M

A rapid automated search method, developed for the location of native gold grains in polished sections with a scanning electron microscope (SEM), has been extended to locate platinum group elements (PGE), in particular platinum and palladium, and their minerals down to 1 ¦m in size. Problems associated with the search for PGE minerals are discussed and examples of PGE minerals located with the facility in drill core sections, crushed ores, and metallurgical test products are given.

Jan 1, 1991

By S R. Grano, J Duan, T A, D Fornasiero

We have determined the experimental rate constants for chalcopyrite particles floated from a complex sulfide ore and compared them with those calculated using a recently developed flotation model. The model incorporates contributions from the efficiencies of collision, attachment and stability between particles and bubbles, as well as their frequency of collision. For these calculations, the contact angle of the chalcopyrite particles in the ore was obtained independently using a surface spectroscopic approach. The calculated flotation rate constants were in good agreement with the experimental data and able to reproduce the characteristic maximum in flotation rate constant for particles of intermediate size. The values of bubble velocity and turbulent dissipation energy derived from these calculations are relatively low and may well correspond to mean values of these parameters inside the flotation cell. We have extended this approach through the application of a property based model to an operating plant, with a satisfactory outcome.

Jan 1, 2005

In many mining operations, the truck and loader equipment represents the bulk of the invested capital and the majority of the mine operating cost. The profitability of these mines is therefore critically linked to the efficiency of the truck and loader operations. The various factors which affect the productivity of trucks and loaders are analysed by computer simulation, and the results presented in a form allowing assessment of the importance of each factor on overall productivity.

Jan 1, 1983