Search Documents

By Hayba DO

Metal-rich slurries discharged from excess-enthalpy geothermal wells at Kawerau (NZ) indicate that an efficient ore precipitation mechanism operates in some feedzones. In our conceptual model, which takes into account the relative permeabilities of liquid and gas phases in boiling fluids, a metal-precipitating liquid phase is effectively immobilised along boiling fronts, leading to the formation of highly concentrated ore. Chemical equilibrium and heat/mass transport modeling demonstrate the general applicability of this conceptual model to hydrothermal eruption environments.

Jan 1, 1995

By P Cherepanskiy, G Elphick, R Hus, C Perring

When an iron orebody nears its end of life, the extracted material can become increasingly problematic to handle. Higher moisture content occurs as larger portions of originally-below-water-table material is mined, which in some deposits is accompanied by further changes in physical and/or chemical properties present along the edges of the orebody. Plant delays related to problematic material have affected all of BHP’s mining hubs to various degrees. Following the recent successful work in Yandi, where the development of an index to quantify the handleability of channel iron ore deposits resulted in an increase in extracted volumes and an extension to the expected life-of-mine, the value of implementing similar indices for bedrock iron ore deposits has been recognised. A materials handling index has been developed by combining observed empirical relationships between material properties and processing plant performance. Indices for each deposit were further refined and optimised by implementing a back-testing strategy which facilitated an understanding of what weighting or scaling each of the contributing components should carry to yield the highest success rate of predicting actual delays at a given plant. Currently materials handling indices are deployed to all mine sites and are made available in block models as well as calculated for individual blasthole and production samples. Values in block models are obtained by predicting the required properties using machine learning models, whereas hyperspectral data is used to ‘measure’ some of those properties on a sample level. This paper discusses the work that has been undertaken to obtain materials handling indices, the testing that has been done to optimise them, and what processes have been developed to ensure the best metrics are being used in the different planning and scheduling horizons to optimise extraction.

Jun 22, 2022

By Fukui M

An increase in pig iron output by 50 per cent was aimed at after re-lining No.2 blast furnace of NAKAYAMA STEEL WORKS. This had to be achieved by increasing both the furnace volume (from 673 to 757 m3) and its productivity, Without equipment for high top pressure operation, high productivity was mainly attained by the following three measures; (1) improving the gas flow characteristics by maintaining a high ratio of agglomerated ores, increasing the strength of sinter and coke, and optimizing the charge distribution, (2) decreasing the fuel ratio by low Si operation and the use of hot blast, and (3) oxygen enrichment. In addition, the tapping controls for pig iron and slag were intensified. As a result of the above measures an excellent hot metal output of 2.7 tonne/m3/day was attained in April 1979 (monthly average).

Jan 1, 1980

By Lilly PA, Kavetsky AP

An empirical, kinematic model is developed which calculates the trajectory of individual blocks of rock in a blast, their point of impact in the muckpile and the final shape of the muckpile. The method is based on the determination of initial block velocity and requires input on stemming length, bench height, subdrill, burden, spacing, energy of explosive per unit length of blasthole, energy attenuation rate and resistance to movement. The model, which will form part of a comprehensive blast simulation package, has application in open cut mining in predicting muckpile geometry and the movement of grade blocks during blasting, which in turn impact on shovel productivity and grade control.

Jan 1, 1986

By J J. Frausto, G R. Ballantyne, M S. Powell, R Cruz, K Runge

Hydrocyclones are the most widely used device for classification in a grinding circuit. However, even the most efficient hydrocyclone has a bypass of fines from the feed to the underflow which reduces comminution circuit performance, as well as misclassification around the cut point. Fine screens classify only according to the particle size, allowing for a reduction in the recirculation of fines back to the mill. The development of high capacity multi-screens makes fine classification in a grinding circuit a viable option. Minera Saucito recently substituted hydrocyclones with screens in its grinding circuit. The change of classifier resulted in an increase in throughput and lead recovery but a decrease in silver recovery. This case study presents the changes in comminution and flotation performance that occurred after the installation of screens and uses historical operational data collected over 12 months of operation to investigate the reasons for these observed changes. CITATION:Frausto, J J, Ballantyne, G R, Runge, K, Powell, M S and Cruz, R, 2017., in Proceedings MetPlant 2017, pp 298–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By M Jahani, M Taji

For suitable production planning in an open pit mine, and also to carry out the optimisation process during the mining production cycle, prediction of fragment size distribution is required prior to carrying out the blasting operation. For this purpose, many prediction models, such as empirical models, were presented. The proficiency of these models differs in various conditions and mines. Therefore, in this paper the most important models, including SveDeFo, Kuz-Ram, CZM, Modified Kuz-Ram in 2005, Kuznestsov-Cunningham-Ouchterlony (KCO) and also Gheibie et al, were examined by the information of 20 blasts in Gol-Gohar iron ore mine. Fourteen images were taken on average for each blast. For image processing analysis Split-Desktop software was used. After examination, it was understood that none of the available empirical fragmentation models had presented acceptable performance, except the Kuz-Ram model for magnetite ore, which had somewhat acceptable results. However, this model for blasting patterns in hematite presented unsuitable results. Examination and comparison of two important distribution functions, Rosin-Rammler and Swebrec, were carried out and it was observed that the performance of Swebrec for fines was far better than Rosin-Rammler. This result for the upper part of fragment size distribution curve, coarse, is the reverse.CITATION:Jahani, M and Taji, M, 2015. Comparison of empirical fragmentation models at the Gol-Gohar iron ore mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 707–714 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Mills KW

Coal mine pillar design formulae available to mine planners are typically based on relationships determined for specific site conditions. Application of these methods is difficult when other factors, relating to mining or geological conditions, not specifically addressed in these relationships are encountered. A review of pillar design methods, coal strength properties and relevant field monitoring of pillar behaviour has shown pillar strength and deformational characteristics are extremely sensitive to in situ behaviour of the rock and other material components that make up the coal pillar system. A method has been developed that has been found to provide excellent correlation between existing field data using the strength and deformational characteristics of materials determined in selected laboratory tests. This method is based on definition of the loading conditions, accurate modelling of the strength, confining conditions and deformation occuring in the roof, floor and coal seam and definition of the in situ strength of coal based on underground monitoring of appropriately sized coal pillar. The design method is considered to provide an accurate and rigorous pillar design method that will give mine planners a more rational mine design capability which is based on the mine geometry and geological setting of the operation. It is envisaged that availability of such a method will allow significant optimisation of pillar layouts and more closely define the geological and mining issues that relate to pillar design optimisation.

Jan 1, 1992

By R Jia, J T. Waldram

"The Caijiaying lead zinc mine is located in China, north-west of Beijing, in Hebei Province. The region experiences severe winters, below -35°C, and warm summers, up to 30°C. The mine and concentrator commenced operations in the second half of 2005 with a conventional tailings disposal system consisting of a tailings dam with peripheral ring main discharge and central water recovery. A second similar dam sharing one common wall was added later. In view of the extreme winter conditions tailings lines and ring mains plus spigots, together with return water lines, require insulation and electrical trace heating. The volume of process water trapped as ice in the tailings dam ponds each winter is significant. This seasonal variation presents a major difficulty in the management of process water availability. Although Caijiaying is an underground mine there was no backfill plant at the start of operations. As plant throughput increased more quickly than originally anticipated, tailings storage capacity became a prime concern. The construction of a backfill plant in 2007 reduced the pressure on surface tailings storage area requirements, but as suitable land on which to construct further tailings storage was both expensive and difficult to acquire, a more efficient use of the available area was required. Dry tailings storage, where flotation tailings are filtered to provide an immediate return of process water plus ‘dry’ tailings filter cake for stacking, provided an answer to both the land area required, and the water management difficulties. The paper details the reasoning behind the change and the benefits obtained at Caijiaying by moving from ‘wet’ tailings storage to ‘dry’ tailings storage.Citation:Waldram, J T and Jia, R, 2016. Caijiaying Dry Tailings Storage, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 379–382 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By R Morrison, P Walters, B Adair, V Jokovic

‘Grade Engineering<sub>®</sub> is an integrated approach to coarse rejection that matches a suite of separation technologies to ore specific characteristics and compares the net value of rejecting low value components in current feed streams to existing mine plans as part of a system-view’ (Walters, 2017). Two of these technologies are directly recoverable through screening stages: Natural Deportment and Induced Deportment. The potential for taking advantage of “Natural Deportment” by size following blasting and crushing has been demonstrated for a range of ore types. Simple and low cost screening can in some cases generate a fine product with improved grade and a lower grade oversize which can be directed to leach or to waste. Where an ore body consists of many different ore types, the traditional approach of blending to metal grade will often add to complexity of treatment, which will reduce the effect of “natural deportment” by size.CITATION: Jokovic, V, Walters, P, Adair, B and Morrison, R, 2018. Applying enhanced grade engineering to complex ore bodies, in Proceedings Complex Orebodies Conference 2018, pp 21–23 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

The activiltion of sphalerite with electrolytically generated copper ions from a copper electrode instead of the usual practice of the addition of copper sulphate was studied in the laboratory. A large surface area of copper was provided by lining three sides of a bench flotation cell with copper sheeting. The lining was connected to the positive terminal of a low voltage d.c. source, and the cell impeller to the negative terminal.Sphalerite was effectively activated by this arrangement and was subsequently floated using xanthate as the collector.Flotation results comparable to those obtained with 1 lb/ton CuS04.5H20 (0,255 lb/ton copper) were obtained using 0·1062 lb/ton of electrolytic copper and 0·488 kWh of electrical energy. The wastage of copper due to the formation of insoluble precipitates was found to be dependent on the length of time the current was passed. Maximum current was passed for the shortest time to minimize wastage.

Jan 1, 1973

By Richards JR, Herbert HK

A basic question in preparing this review was how to define sulphur mineral occurrences as being associated with the Pacific Rim. This question will be reconsidered later. The isotope composition of sulphur- containing minerals may be considered in terms of two primary sources - 1. deep- seated sulphur, devoid of crustal contam- ination with a 634S value near 00/0o and 2. oceanic sulphate which fluctuated in value between +10 and +300/00 over geological time (Claypool et al., 1980). However, minerals have seldom been directly derived from these primary sources as even evaporites have been dissolved and reprecipitated. The marine source is differentiated biochemically and isotopically in recent sediments where sulphide from bacterial sulphate reduction may be significantly depleted in 31S. The question of chemical interaction of ascend- ing magma with upper crustal rocks has become one of degree rather than whether or not it occurs. Mineral deposition is considered increasingly in terms of mixing of fluids and their chemical reactions with rocks rather than direct precipitation from magmas or hydrothermal fluids derived from them.

Jan 1, 1987

By W Y. Guo, L X. Chen, D X. Zhang

To obtain the rock type-I crack propagation process accurately, a novel fixture is used to make the prefabricated crack of rock propagation along the predetermined direction. In this study, the crack propagation process of rock is monitored with the digital image correlation method (DICM), and a mechanical model of crack directional propagation was established. The results show that the simple crack directional propagation device can effectively realise the stable propagation of type-I crack along the predetermined direction, the crack initiation angle is less than 10°, and the deviation between the peak strength of crack propagation calculated by a simplified mechanical model and the tensile strength of Brazilian splitting is 22.76 per cent and 7.53 per cent, respectively. According to the deformation field evolution law, crack propagation can be divided into three stages: microcrack development, main crack propagation, and main crack propagation. As for the rock type-I crack initiation and propagation mechanism, before reaching the peak strength, the prefabricated crack tip is subjected to maximum tensile stress; the elastic energy increases rapidly, and the dissipation energy increases slowly; after the peak strength, elastic energy exceeds its energy storage limit and released rapidly, and most of the input energy is converted into dissipation energy, which makes the crack propagation rapidly. The crack directional propagation device will be further optimised and improved, and it is expected to provide a new method for the study of crack propagation mechanism, rock failure precursor information and crack arrest principle, etc. It will also provide theoretical references for the optimisation of coal strata directional blasting, fracturing, fracture arrest, and other related technologies in geotechnical engineering.

Nov 29, 2022

By Sheer T. J, Van Rensburg J P

The primary objective of this research was to address the demands imposed on self- contained self-rescuer (SCSR) performance dur- ing simulated escapes. The results clearly indicate that SCSR performance, apart from the inherent technological features, is a function primarily of the physical and anthro- pometric features of the wearer, and of the particular nature of the escape route. These factors consequently play a major role in the planning of any escape strategy, which may vary from mine to mine. It is therefore concluded that each mine would have to formulate its own escape strategy which in turn would depend on the choice of SCSR, and the particular escape Route.

Jan 1, 1988

Studying the ore textures in a discrete orebody is a novel approach to estimating liberation potential of the ore minerals present. As part of a PhD thesis, this project aims at classifying and quantifying the textures of the Hilton North orebodies, and at estimating their liberation characteristics.

Jan 1, 1993

The paper is introduced by some general comments on the Electrolytic Zinc Company West Coast Mines operations. An outline of the geology of the Rosebery Mine orebodies preced- es a resume of the mining methods used prior to the current mechanization programme. The reasons for the introduction of longhole stoping techniques are given together with a brief explanation of both sublevel longhole and longhole stoping methods. The application of remotely controlled loaders within these stoping methods is discussed. A description of the remote control mechanisms, used on Atlas Copco 310 and 511 Cavo loaders, is followed by comments on these mechanisms from both a maintenance and production viewpoint. A summary of perform- ance statistics and operator safety records vindicate the selection of remotely controlled loaders for the longhole stoping areas at Rosebery Mine.

Jan 1, 1977

Minerals and Metals Group (MMG) Century mine (Century) is a large open-cut mine in northwest Queensland approximately 2.5 km long, 1.5 km wide and 240 m deep, with an ultimate pit depth of 320 m. In 2009, the mine experienced three failures which began as small failures, and progressively developed into significant multi-batter failures. The incidents were managed by a combination of analysis, redesign and practical management to achieve positive outcomes for the mine. On the south wall of the mine, a series of batter-scale wedge failures occurred in December 2007. Analysis of structure orientations and design changes aimed to minimise the risk of failure extending over multiple batters, while accepting a risk of further small-scale failures. Design changes were constrained by a culturally sensitive area (CSA) located south of the wall. As mining progressed, shallow wedge failures developed over multiple batters and cracks were observed 60m back from the pit crest, indicating that a large-scale wedge failure was developing. Movement increased in January 2009 as a result of significant rainfall. After considering several design options, the area was stabilised by a cut-back of the wall. Two multi-batter failures also occurred on the north wall as mining progressed through a structurally complex area. Both north wall failures began as small failures that progressively developed, and required a redesign of the wall below as well as practical management of safety aspects. The complex structural geology was difficult to predict ahead of mining, and required geotechnical input into design changes as mining progressed. All three failures potentially had significant impact for ore recovery, and were managed by a combination of analysis, redesign and operational management have resulted to achieve positive outcomes in a challenging mining environment.

May 1, 2010

By C E. Woolley, H Jebaliya, J Foster

The East wall of the Kalgoorlie Consolidated Gold Mines Fimiston Open Pit (KCGM Superpit) has a history of wall instabilities impacting mining operations; the most significant of which occurred in May 2018, when more than 1 Mt of rock dislodged over six, 30 m high bench stacks and impacted the pit floor. Since 2011 approximately 1.250 Mt of material has fallen from the East wall at Fimiston Pit across three failure events (2011, 2018 and 2020). Each failure has been associated with major structures intersecting the pit walls: the Fiji Fault, the Australia East Secondary Splay Fault and the EWD3 Fault. In each instance the trigger for failure has been transient pore pressure in the pit walls. Northern Star will mine a cut back behind the failure area over a vertical distance of 180 m. Cut back mining will include the extraction of a remaining in situ wedge, which is assessed as kinematically able to fail, and a subvertical failure backscarp in Stage 1. A substantial amount of rill material from the 2018 and 2020 failures will be extracted in Stage 2. This paper presents the methodology in use to mine Stage 1 of the cut back, safely, through this potentially high-risk area, detailing the specific mining methodology employed, the controls put in place and the monitoring required. Day-to-day monitoring will be undertaken using the already installed slope stability radar and will feed into a daily assessment of activities which may be undertaken in the cut back area. Initial activities will focus on eliminating the potentially unstable wedge and vertical backscarp with use of innovative drill and blast techniques/products and the extensive use of remote capable equipment to limit personnel exposure.

Jun 22, 2022

By O N. Antzutkin, A V. Ivanov, W Forsl

Polycrystalline and surface complexes (at synthetic sphalerite, ZnS, and galena, PbS) of zinc(II) and lead(II) ions with eight different O,OÆ-dialkyldithiophosphate (Dtph) substances have been prepared and comparatively studied by means of 31P CP/MAS NMR spectroscopy. The 31P resonances have been assigned to dithiophosphate groups with terminal S,SÆ-chelating or bridging coordinations in the mono-, bi-, tetra- and polynuclear complexes respectively. The bridging coordination of two neighbouring zinc(II) ions by O,OÆ-dialkyldithio-phosphate ligands was established at the surface of synthetic sphalerite.The adsorption mechanism of dialkyldithiophosphate on synthetic galena includes formation of a surface complex as well as surface precipitation. Principally different coordination modes of the reagent were discovered at the surfaces of galena and sphalerite (ie terminal S,SÆ-chelating coordination to the lead atom).Derivatives of monothiophosphoric and phosphoric acids were displayed as hydrolysis products of dialkyldithiophosphates at synthetic PbS.

Jan 1, 2005

In his letter of resignation as General Superintendent of the Broken Hill Associated Smelters (BHAS) prior to taking up aconsulting position at imperial Smelting, G.K. Williams wrote that he considered his major contributions at BHAS were:the development of large scale sintering machines;the double tuyere-row blast furnace; continuous lead refining.Despite his well deserved reputation as a scientist, based on his advancement of the metallurgical chemistry underlying lead refining processes, Williams reveals that he considered commercial implementation as the ultimate measure of technological success. Furthermore, he clearly did not differentiate between the scientific and the empirical as a means of achieving that end.

Jan 1, 1985

The Mt Muro gold and silver deposit in Central Kalimantan has been in production since December 1994. The geology is characterised by narrow high-grade lodes containing gold and significant amounts of silver. From a largely untrained workforce in the grade control department, production per crew and per geologist has tripled during the three years of production. Grade control drilling evolved from blast hole sampling to reverse circulation sampling. National geologists are trained in basic modeling procedures. A fully integrated reporting and reconciliation system was programed and implemented.

Jan 1, 1997