Search Documents

By M Freeman

In a visionary move, the Planning Commission and the Ministry for Planning in Western Australia decided to invite three extractive industry quarry operators, local government councils and State Government departments (Minerals and Energy, Environmental Protection, South West Development Commission) to contribute jointly to study the impacts of blasting on areas surrounding basalt quarries in the Bunbury region of WA. The results of the study will help establish suitable zones in which land uses will be controlled under a proposed Greater Bunbury Region Scheme and in local planning schemes, to minimise conflicting land uses. This paper discusses the blasting program conducted to characterise and model the vibration behaviour of the rock under the effects of pilot-scale and full production blasting, and highlights some of the benefits achievable when a thorough blasting impact program and assessment is conducted at the planning stages of land-use establishment.

Jan 1, 2001

By O van Baalen

The Ernest Henry Mine is a copper-gold open pit operation situated in northwest Queensland, Australia. It is owned and operated by Xstrata Copper, with a current throughput of 11 Mtpa, however, open pit operations are scheduled to cease in mid 2011. The deposit dips approximately 45º and extends for at least another 400 m vertically below the final 530 m deep pit design.Construction and development of a sublevel caving (SLC) operation beneath the open pit was approved in December 2009. The feasibility design requires 39 km of development to be completed prior to production, which will commence in the fourth quarter of 2011. Initial ore production will be trucked and will increase to 3 Mtpa by the end of 2012, after which a hoisting shaft will be used. Ore production will then increase to 5 Mtpa in 2013 and ultimately to 6 Mtpa in 2016.Two 3000 kilo watt of refrigeration (kW(R)) modular refrigeration plants will be installed, as well as two 1600 kW mixed-flow fans capable of a combined flow rate of 780 m3/s at a total pressure loss across the mine of 2000 Pa. The main fans will be installed underground and will exhaust into the base of the pit.The following challenges were faced in the development of the ventilation and refrigeration network:•a relatively steep geothermal gradient,•tropical ambient conditions,•working under a wide pit shell, and•a large underground trucking fleet prior to shaft commissioning.A considerable number of ventilation studies were conducted with later studies extensively using Ventsim Visual™ mine ventilation software to complete the design process of the ventilation and refrigeration networks, including the comparison of several alternative designs. The paper focuses on design challenges prior to the commissioning of the hoisting shaft, and discusses resistance optimisation and occupational hygiene-related design parameters, such as heat and diesel emissions, production level ventilation, main fan selection and location, and refrigeration requirements.

Mar 21, 2011

By L Dzinza, K C. Corin, M Tadie

The recycling of process water comes with increased electrolyte concentrations that affect water quality, which may in turn affect the flotation performance of valuable minerals (Hirajima et al, 2016). Electrolytes such as Ca2+, SO4 2- , Mg2+ and S2O3 2- have been surmised to have an impact on the action of flotation reagents such as collectors (Ikumapayi et al, 2012). Xanthate collectors are known to play a significant role in imparting hydrophobicity on mineral surfaces to enhance their flotation. The interaction between minerals and xanthates is well known to be electrochemical in nature. Such redox processes may be elucidated by electrochemical techniques. Since the mechanisms involving the interactions between electrolytes in process water with sulfide minerals and the subsequent adsorption kinetics of collectors are not well understood, this study therefore aims to provide fundamental knowledge to unpack the mechanisms involved when electrolytes interact with Platinum Group Minerals (PGMs) and how these interactions may affect xanthate adsorption. The interaction of sodium iso-butyl xanthate (SIBX) in the presence of electrolytes at increasing ionic strength was investigated by rest potential measurements, to explain the impact of electrolytes on the adsorption of SIBX on PGMs in the flotation process. Rest potential measurements for PdTe2 and PdS were conducted in an air saturated 0.05 M di-sodium tetraborate decahydrate solution, in the absence and presence of SIBX and electrolytes. It was found that the existence of sulfide and telluride on palladium affects the mechanisms in which electrolytes interact with Pd mineral surfaces. An increase in the ionic strength of Na2S2O3, CaCl2 and MgCl2, increased the interaction between the salts and PdS, thus decreasing the extent to which SIBX interacted with PdS. An increase in ionic strength for Na2S2O3 increased the interaction between Na2S2O3 and PdTe2 and therefore decreased the extent to which SIBX interacted with PdTe2. Other salts investigated in this study increased the rate of oxidation of PdTe2 with an increase in ionic strength thereby enhancing the interaction of SIBX and PdTe2. This study has shown that mineral type, electrolyte type and concentration all have an impact on the mechanisms that result in the adsorption of SIBX on PGMs.

Aug 24, 2022

By M J. Davies, R S. Davies

Despite increased expenditure, the global discovery rate of world-class ore deposits has been in decline for over a decade (Schodde, 2017). Mineral exploration has traditionally followed an empirical approach, searching for evidence of mineralisation upon the surface of the planet, then drilling to define the extent of an ore body beneath the surface. As outcropping deposits in well-defined areas are depleted, there is a need for exploration to extend to less well-explored search spaces. One popular new frontier is exploration at greater depths beneath the Earth's surface. However, exploring for deep deposits with limited surficial evidence requires the implementation of predictive targeting methodologies (Hronsky, 2011; McCuaig & Hronsky, 2014). The Mineral Systems Concept (Hronsky & Groves, 2008; McCuaig et al., 2010) provides a framework for predictive exploration targeting. Ore deposit formation is recognised to be a focused mineralising event. These events represent self-organising critical systems and are underpinned by the interaction of complex, non-linear processes. Through the collection and analysis of datasets that map mineralising processes, it may be possible to predict the size and location of resultant ore bodies. CITATION: Davies, M J and Davies, R S, 2018. Beyond below-ground geological complexity: Developing adaptive expertise in exploration decision-making, in Proceedings Complex Orebodies Conference 2018, pp 95–98 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By D J. Bradshaw, B Lottermoser, A Parbhakar-Fox

"Best practice for acid rock drainage (ARD) risk assessment still relies solely on the geochemical properties of sulfidic rocks and mineral processing products, despite the fact that a rockÆs tendency to produce acid also depends on mineralogy and texture. Consequently, there are a plethora of geochemical tests routinely utilised by the mining industry to predict ARD formation. Due to limitations associated with these tests and their relatively high costs, analysis of recommended best practice sample numbers is rarely achieved, reducing the accuracy of waste management plans. Our research addressed this through examining the application of geometallurgical data for predicting acid formation, and led to the identification of potential environmental geometallurgy indicators.Samples obtained from an iron-oxide copper gold deposit were subjected to the geochemistry-mineralogy-texture (GMT) approach, an improved methodology for classifying acid forming potential. GMT results were compared against geometallurgical and assay data sets to evaluate: relative carbonate content measurements (measured by HyLogger) and identify how these could be used to calculate effective acid neutralising capacity mineral hardness (measured by EQUOtip) to determine application of this data for calculating lag-time to acid formation opportunities to automate the acid rock drainage index (ARDI) using classified images produced by a GEOTEK logger and automated microscopy.Links between the GMT approach and geometallurgical data sets were identified. Classified mineralogy data has application at stage one, HyLogger and EQUOtip at stage two and computer-based ARDI evaluations of classified images at stage three. Through such integration, ARD characterisation costs can be reduced, with value added to geometallurgical data sets. Furthermore, deposit-wide ARD domaining is possible, and acquisition of total-orebody knowledge more likely. Through adoption of this environmental geometallurgy approach, a better informed waste management plan can be formulated, allowing for best practice ARD sampling in a more cost-effective manner.CITATION:Parbhakar-Fox, A, Lottermoser, B and Bradshaw, D J, 2013. Cost-effective means for identifying acid rock drainage risks - integration of the geochemistry-mineralogy-texture approach and geometallurgical techniques, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 143-154 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By B Maybee, L Fava, D Millar

In the context of a case study for an underground gold mine, the value generated by a schedule optimisation tool (SOT) is assessed. SOT is a software tool for underground mine planning that maximises the net present value (NPV) of a development and production schedule. A baseline study measures the NPV of a schedule generated by SOT from a sequence prepared by the site mine planners. Operational resource constraints and precedence constraints are adhered to by the schedule and NPV is evaluated with a financial model including revenues, costs and discount rate, as specified by the mine planner.The case study has several facets in addition to the baselining component. Scenarios were conducted that examined the degree of constraint on operational resources, the projected gold price and unit costs. Life-of-mine schedules subject to optimisation using SOT allowed for equitable comparisons.Haulage was identified as a dominant constraint for the mine. It was one of six operational resources that were used to constrain the optimisation of the mine schedule, with alternative levels for some of these constraints being identified so that their effects on the NPV could be studied. Alternative price projections for gold and different cost projections were identified and their effects on the optimised schedule examined. Price and cost scenarios that brought additional economic material into the schedule at various times in the mine life were considered in comparison to a scenario that assumed no additional economic material would become available.This case study illustrated that the use of a schedule optimisation tool to optimise mine schedules provides mine planners with an ability to perform a wide variety of analyses in a relatively short period of time. Such tools thereby support strategic decision-making that can add significant value to an orebody.The case study demonstrates that by fixing the set of development and production activities to be carried out before optimising the life-of-mine schedule, the mine planners can inadvertently set up a situation where the NPV would be progressively eroded in the last several years of the mine life. This clearly illustrates the need for schedule optimisation to be integrated with life-of-mine planning.CITATION:Fava, L, Maybee, B and Millar, D, 2012. Decision support for an underground gold mining operation - A case study using the schedule optimisation tool, in Proceedings Project Evaluation 2012 , pp 41-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

The industrial practice of separating finely' around valuable minerals from associ- ated gangue materials by froth flotation is well known. Despite the obvious importance of this industrial process, the predictive tools for plant engineering evaluation of flotation process variable changes are still in a developmental stage. Consider, for example, the situation where an operating engineer is faced with evaluating a change in an existing chemical reagent scheme, possibly based on batch laboratory data. When all is said and done, the engineer must still perform detailed physical testing of the proposed reagent change on the actual equipment in plant use to be confident even of the direc- tion of change of plant results, let alone the economic viability of the change. The theory behind chemical reagent behaviour in froth flotation has been studied extensively, e.g., (Aplan {1980}, Fuerstenau {1976}, Fuerstenau {1962}, and Somasundaran {1980}), and, certainly, important progress has been made. Unfortunately, the nature of the flotation process, with its complicated heterogeneous surface chemisty activity operating on highly variable and difficut to characterize ore surfaces, coupled with com- plex mass and momentum transfer phenomena, :;l riously compromises the plant scale predictive capability of theoretically based models.

Jan 1, 1978

By J Theiler, B Beamish

Spontaneous combustion hazard assessment from an environmental impact perspective is not well understood and is seldom given due consideration in environmental impact statements. In surface mining operations, self-heating, leading to spontaneous combustion may occur when rock units containing reactive metal sulphides and organic carbon are disturbed by mining operations and exposed to the atmosphere. When these rocks are present self-heating will occur in situations where the rate of heat generated from oxidation reactions exceeds the rate of heat lost to the surroundings. The processes and mechanisms that lead to spontaneous combustion events are varied and generally complex. To effectively manage spontaneous combustion in surface mining operations, it is necessary to characterise the spontaneous combustion propensity of the geological materials involved. Until recently there has been no testing procedure for assessing the propensity of waste rock to spontaneously combust that has been adopted by industry. However, new developments in adiabatic test methods have proven successful in determining the self-heating behaviour of coal (Beamish and Theiler, 2015) and coal containing reactive pyrite (Beamish and Theiler, 2017). These adiabatic test methods have now been modified to assess the incubation behaviour of waste rocks and can be used for their spontaneous combustion characterisation in advance of mining (Beamish and Theiler, 2016). The new method provides a practical means to establish the likelihood of developing a spontaneous combustion event for the specific site conditions. This paper presents examples of the use of a cost effective first pass filter for assessing spontaneous combustion potential of waste rock based on geochemical data from four surface mines. This is supported by adiabatic Incubation Test results for three of the mines and visual examination of cores for one of the mines. CITATION:Theiler, J and Beamish, B, 2018. Valid spontaneous combustion hazard assessment for surface mine environmental impact statements, in Proceedings Life-of-Mine 2018, pp 64–67 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By N Robson, E Stephens

Australian mining companies are actively exploring for and developing mineral deposits throughout the world with interests in emerging markets such as Africa, Asia and South America. It is important to understand emerging market risk as this will affect the willingness of mining companies and financial institutions to invest in a country, especially with reference to their key asset, the mining licence or operating/concession agreement. Mining companies looking to develop new projects in emerging markets have different risk profiles than projects in countries such as Australia and Canada. Examples of key risks faced in emerging markets include: political û expropriation, nationalisation, contract frustration, currency inconvertibility, war, terrorism, strikes, riots and civil commotion; and legal û mining legislation, arbitration and dispute resolution, trade agreements. There is a problem in the difference in risk perceptions between mining companies, financial institutions and insurers. This can cause different stakeholders to carry out different evaluations of the risks faced by a project, resulting in confusion about the risk margin attached to any project. In a time where resource nationalisation and energy security are prompting governments to become more involved in the mining sector we run through some recent examples of mining companies that have had problems due to the key risks highlighted earlier. Importance of carrying out the right due diligence to replace perceptions with reality: early identification of risks û detailed due diligence on emerging market risks that may arise will help with their identification and mitigation, make use of companies that can help identify risks and suggest solutions, control the cost of financing û risk margin applied to a project finance loan will be influenced by the risks faced, and risk management and using political risk insurance. There are plenty of opportunities in emerging markets but it is important to recognise the associated risks. Detailed due diligence at an early stage will provide long-term benefits.

Jan 1, 2007

By B Dold

"Mining has still today high potential for improvement in the exploitation efficiency. Especially low-grade ores have very low recoveries. In Cu bioleaching operations from porphyry copper deposits extraction of only five and 15 per cent with maximum of 40 per cent are reached. This means that 60–95 per cent of the resource is not exploited. Consequently, any metal not extracted will end up in the waste material, therefore increasing the risk of environmental pollution. This inefficiency is mainly due to the use of element concentrations for decision-making on the daily basis of a mining operation (eg cut-off ore grade, acid-base accounting – ABA). If, instead, quantitative mineralogical and geochemical data together with information on the bioleaching behaviour of the ore assemblage (the biogeometallurgical approach), is used for decision-making right from the beginning of the exploitation, higher recoveries and less environmental impact can be achieved, ie an increase in sustainability can be reached.CITATION:Dold, D, 2016. The Biogeometallurgical Approach – the Information We Need to Increase the Sustainability of Mining, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 169–172 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By H Indirawati, R Ayres, A Nur Kasnanto, S Konopa

As a project moves through the mine life cycle, the quantity of data available increases and the understanding of the orebody matures. Incorporating new information quickly and efficiently in current 3D models, is essential for adding value across the life-of-mine value chain. At the Martabe Gold Mine, the resource development group manages 14 drill rigs on six resource projects, including three operating mines. The Martabe deposits are geologically complex and the volume of new information that becomes available each day is substantial. It is imperative that new geological and assay information is integrated into the 3D models as soon as possible, so that drill planning and targeting can be modified accordingly. Martabe uses Leapfrog<sup>®</sup> 3D software to update and interrogate the 3D models on a dynamic basis as data becomes available. This results in faster and more effective changes to drill planning and schedules. The impact of this is better drill productivity and cost savings due to optimal drill targeting, and availability of up-to-date models incorporating the most current data. CITATION: Konopa, S, Ayres, R, Nur Kasnanto, A and Indirawati, H, 2018. Optimised drill targeting using dynamic 3D modelling, Martabe Gold Mine, Indonesia, in Proceedings Complex Orebodies Conference 2018, pp 99–101 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

Sishen uses a state-of-the-art tracking system to track material from its position in blast blocks through various stockpiles and crushers. Qualities are blended directly to the crusher as opposed to blending from stockpiles. This poses an interesting challenge to the planning department to simulate these conditions. The software used in these simulations are Whittle 4X and Maximiser for long-term planning, Xpac for medium-term planning and Mine Works Planner for short-term planning. Geological models and mine design layouts utilise Surpac. Sishen introduced Xpac a number of years ago; the system has developed and changed over the years. With the Sishen Expansion Project (SEP), which aims to utilise low-grade material, major changes to the planning process have to occur. SEP requires that the mine have two different plants, which utilise two different ROM feeds and have different beneficiation curves. Xpac is used to produce a rolling 18-month plan, which is as close to actual operations as possible. In order to do this, the simulations have to take into account the plants beneficiation curves, stockpile movements, hauling distance and equipment needs. On top of this, the schedule has to continually consider specifications for Fe and the contaminants. Plant yields also have to be kept within a certain bandwidth. Xpac is used to simulate the above parameters, as well as generate the raw data required to produce a mine budget. The paper will also show how the 18-month planning process and subsequent planning processes are measured and aligned. Xpac has proved to be an excellent tool to achieve these goals.

Jan 1, 2005

By Juras ST, Krouse RH, Godwin CI

The Buttle Lake camp is in central Vancouver Island, southwestern British Columbia, Canada. The camp hosts world-class polymetallic volcanogenic deposits of Devonian, Frasnian age (370Ma). This paper describes an on-going sulphur and lead isotope study of the major orebodies.Sulphur isotopes were determined for sulphides (pyrite, chalcopyrite, bornite and galena) and sulphate (barite). Sulphide analyses are markedly different from sulfate. The differences are explained below in a unique model.Sulphide isotopic compositions cluster tightly (del34S -6.7 to 4.6), and demonstrate isotope reversals. Calculated temperatures of correctly ordered mineral pairs are unrealistically high. We conclude that the sulphides are in isotopic disequilibrium, presumably because of rapid precipitation from a quenched plume in an anoxic environment, and because of subsequent sulphide replacement.

Jan 1, 1990

By T Baumgartl, M Edraki, L Huang, D R. Mulligan

"Phytostabilisation with tolerant plant species has been advocated as a cost-effective solution for sustainable cover of tailings from metal mines and bauxite refinery. The development of sustainable plant ecosystems on such wastes requires not only tolerant plant species compatible with local climatic conditions, but also the formation of stable and functional root zones through systematic processes to develop functional soil matrix and horizons (eg A-B-C). However, the process requirements for reconstructing functional root zones in tailings are poorly understood. Based on a review of current literature and industry experience in tailings revegetation, the present paper conceptualises three key phases in the process of root zone development in amended tailings: hydro-geochemical stabilisation resulting from the interactions among tailings characteristics, amendment measures and local climatic conditions the rehabilitation of soil biological capacity the establishment of ecological (carbon and nutrient) linkages between the rehabilitated root zones and the above ground plant communities.Key research is required on: the relationship between hydro-geochemical stability and mineralogy and geochemistry of tailings, in response to rehabilitation treatments under local climatic conditions the relationship between soil biological capacity and hydro-geochemical stability in the root zone the transition of soil microbial communities specific to exogenous organic matters into those required for mineralising litters of in situ plant communities.CITATION:Huang, L, Baumgartl, T, Edraki, M and Mulligan, D R, 2012. Sustainable phytostabilisation of mine tailings - A critical analysis of system requirements and approaches, in Proceedings Life-of-Mine 2012, pp 105-116 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By J Tien, J Huang, N Haque, M O’Brien

Coal preparation is an integral part of producing coal for thermal powerplants and metallurgical processing plants. Coal processing plants use various unit processes to separate gangue and ash content from mineral coal, thus increasing the specific energy content.A flow sheet and a simulation model was established for a typical coal processing plant using Microsoft Excel. This model used the mass balance and split factors for run-of-mine (ROM) coal, tailings and water usage from a typical, generic coalmine.The common method of coal preparation initially involves several stages of crushing to reduce the size of coal. It is then sent to the processing plant for further washing. The typical method in Australia for coarse coal material processing is the use of dense medium cyclone (DMC) (Kininmonth and Baafi, 2009). Flotation cells are used for processing of fine coal. The fine products are utilised for coking coal only. In our case study, the intended coal product is for thermal powerplants. Therefore, the fine coal processing utilised spirals instead of flotation, which is typical for the industry.CITATION:Huang, J, Haque, N, O'Brien, M, O'Brien G and Tien, J, 2016. Development, simulation, economic and environmental evaluation of a coal processing flow sheet, in Proceedings Life-of-Mine 2016 Conference , pp 48–51 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By M J. Dunn

The geotechnical model is the cornerstone of any mining geotechnical design and as such the confidence level and reliability of the geotechnical model is paramount. The geotechnical model confidence level needs to be commensurate with the level of design that is being applied or study that is being undertaken. The geotechnical model is made up of several components and the reliability of the data underlying these components ultimately determines the reliability of the geotechnical model.Data reliability is linked to the quantity of data collected, the spatial distribution of the data collected, quality of the data collection and the interpretation of the data. In a typical project, there is an opportunity to improve data reliability through the scoping, prefeasibility, feasibility and final design and implementation stages.Currently, very little quantitative guidance exists in the literature on assessing the confidence level of geotechnical studies, although there have been attempts by various authors (Haile, 2004; Haines, Swart and Kruger, 2006; Read and Stacey, 2009; Dunn, Basson and Parrott, 2011) to qualitatively describe what level of geotechnical data is required. Recently a number of authors (Read, 2013; Fillion and Hadjigeorgiou, 2013; Thomas, 2013) have outlined methods that could be applied to assess the reliability of some types of geotechnical data that are used in the development of geotechnical models.This paper briefly discusses some of the factors influencing data reliability and the geotechnical model confidence and some of the tools available.CITATION:Dunn, M J, 2014. Geotechnical models and data confidence in mining geotechnical design, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 127–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By D Xu

BHP Billiton Iron Ore is one of the world’s premier suppliers of iron ore. It currently has operations in Western Australia and Brazil and also has some iron ore interests in West Africa.BHP Billiton’s Optimisation R&D team has developed a proprietary mine planning optimisation tool that uses a mixed integer linear programming (MILP). This tool is called Blasor and it is used to rapidly evaluate the resource development potential (RDP) scenarios for the company’s business development strategy. In addition it generates life of asset (LOA) mine plans for the company’s operations and growth projects. The Blasor optimiser maximises the discounted operating cash fl ow (DCF) as the objective function, subject to mining, processing and transportation capacity constraints and blended product quality constraints. The paper will outline how Blasor has been applied to the resource development potential (RDP) strategy scenario studies, growth project evaluations and LOA mine planning within BHP Billiton Iron Ore.The practical application of Blasor to resource planning optimisation within BHP Billiton Iron Ore has demonstrated the value of such a tool for optimising strategic directions through the evaluation of a number of carefully proposed scenarios and maximisation of operational decisions, such as cut-off grade, open pit development sequence, etc. Particularly for the company’s business development direction studies, Blasor plays the role of a fair valuation tool in that it discovers the most valuable resource development scenario, thus establishing a sound basis for comparing the economic merits of each scenario.

Jul 11, 2011

By A Satyanaga, H Rahardjo, K G. Mercer

The soil-water characteristic curve (SWCC) is one of the most essential soil properties in unsaturated soil mechanics. The water flow and storage characteristics of an unsaturated soil are closely related to the amount of water contained in the pores and the negative pore-water pressure in the soil. These are both in turn, related to the particle-size distribution and the plasticity of the soil. The SWCC is obtained by laboratory testing which is difficult to perform, costly and time consuming. There is a significant advantage in establishing typical SWCC envelopes for different soil types from a geotechnical design and analysis viewpoint. This paper presents some of the research work undertaken by UWA and NTU to develop SWCC envelopes for soil types classified in terms of the ASTM D2487 Unified Soil Classification System (USCS). This was done by establishing a large database of soils from across the world, classifying them according to ASTM D2487 and undertaking SWCC testing for each soil. This paper presents the SWCC test results from a selection of three of the most common soil classifications encountered in geotechnical engineering practise.CITATION:Mercer, K G, Rahardjo, H and Satyanaga, A, 2018. The development of soil water characteristic curves for soil types classified according to the USCS, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 263–273 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

The Australian Mineral Industry has to compete on world markets, so its mineral research has to be aware of overseas developments, it must be of world class, and it must utilise as many ideas as possible in order to solve those problems that uniquely affect Australian minerals processing. North American mineral and resource research may be taken as a guide to world government, industrial, contract, and entrepreneurial research trends and ideas. A number of interesting findings are noted that may guide Australian developments and strategies for the future, in minerals research and exploitation.

Jan 1, 1986

By A Vakili, F Harvey, H Greaves

Mine seismicity is one of the most difficult geotechnical risks to manage in seismically active mines. There are currently some established empirical and statistical methods that provide quantitative measures for seismic hazard assessment in operating mines. However, these methods are mostly suitable for quantifying the current or historical seismic hazard and often cannot be directly used to forecast the future hazards. Numerical modelling is the only analytical tool that can capture the level of complexities required for a meaningful analysis of mine seismicity and therefore to facilitate a reliable forecast of future hazards. However, there is currently no widely accepted and established guideline and methodology for analysing and forecasting mine seismicity using numerical modelling. This paper first provides a background on previous published studies on this subject and then outlines the key aspects that can affect the reliability of the forecasting for mine seismicity. These aspects include a) processing of historical seismic data, b) selection of suitable numerical modelling approach, c) Post-processing and interpretation of the model outputs. A case study is then presented for the Gwalia Deeps Mine where a new framework was developed to forecast future mine seismicity. High-quality seismic data for a period of five years was used for back-analysis and comparisons with the numerical modelling outputs. After development of the method, the future seismicity was forecast for the next 12 months and the actual seismicity was monitored against the forecast during this period. Results of this study shows promising potential for the proposed framework to be applied more routinely and at other mine sites. However, more validations are required at Gwalia Deeps mine as the mine proceeds to deeper levels. In addition, the method needs more improvements and should be tested and validated at other mining operations before it can be established as a proven method. CITATION:Vakili, A, Harvey, F and Greaves, H, 2018. Forecasting mine seismicity – towards a more established methodology, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 207–222 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018