Search Documents

By Z Terzic, M Schult, D Chu, S Macklin

The East West Link road tunnels are proposed to provide a connection between the CityLink toll road and the Eastern Freeway north of the Melbourne CBD. The alignment passes from Moonee Ponds valley beneath the Upfield Line railway cutting, Royal Park, the historic Melbourne Cemetery and beneath Alexander Parade rising to an eastern portal at Hoddle Street. The western (Royal Park) part of the alignment passes through the folded and faulted Silurian Melbourne Formation, which has been subjected to deep weathering since the Triassic.The Melbourne Formation in the Royal Park area is mainly characterised by interbedded sequences of siltstone and fine-grained sandstone. The beds are often graded and a clear boundary between the siltstone and fine-grained sandstone rock can be difficult to distinguish. Variation in lithology and the presence of structural geological features such as folds and faults have resulted in an irregular weathering profile within the Silurian rock; nonetheless the formation typically becomes less weathered with depth.Due to difficulties in obtaining reliable laboratory strength and stiffness relationships with weathering grade, in situ testing methods such as downhole shear wave velocity and high-quality pressuremeter testing are a useful aid to assessing appropriate geotechnical parameters for design.This paper presents an analysis of the variation in shear modulus of the Melbourne Formation, determined at small-strain (from downhole seismic data) and at ‘engineering scale’ strain (from pressuremeter tests) for extremely weathered (XW), highly weathered (HW) and moderately weathered (MW) rock. Estimates of small strain shear modulus (Go) obtained a range between 400 to 3400 MPa for these weathering grades. By comparison against the pressuremeter test data, reduction factors to be applied to these Go values to estimate shear moduli at engineering strain levels typically range between 0.10 and 0.35.The downhole geophysics undertaken in the Royal Park boreholes also suggests that there is an inversion in velocity between approximately 15 and 27?m depth below the top of the formation. This is thought to be related to the effects deep Plio-Pleistocene weathering, iron cementation of joints and increasing frequency of ‘non-healed’ joints in the transition from MW to slightly weathered (SW) rock.CITATION:Macklin, S, Schult, M, Terzic, Z and Chu, D, 2014. Strain-dependent stiffness of the weathered Melbourne Formation, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 179–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J Lombardi, M Weidenbach

"OZ MineralsÆ Prominent Hill copper-gold concentrator is located 650 km north-east of Adelaide, 130 km north-east of BHP BillitonÆs Olympic Dam operation and 130 km south-east of the regional township of Coober Pedy, in the Gawler Craton region of South Australia. The concentrator was built in 2008 and commenced commercial production in early 2009. The Prominent Hill concentrator is comprised of a conventional grinding and flotation processing plant with a 10 Mt/a ore throughput capacity, operating well over the design rate of 8 Mt/a. Increased throughput rates have seen a decreased water recovery from the tailing thickener due to operating above design. Subsequently, greater pressure was placed on the site water balance and bore field off-take rates due to increased evaporation losses from greater volumes of water reporting to the tailing storage facility. This resulted in a trade-off between water availability and milling rates as part of the operating strategy.Two projects were implemented to increase the tailing thickener underflow density, thus improving water recovery directly back into the operating plant, reducing water losses via evaporation and decreasing the reliance on the bore field system operating at maximum rates to maintain mill throughput. The two projects were: tailing thickener feedwell redesign implementation of the Manta Cube control system.This paper discusses the background, implementation and benefits attained from these two key projects. Combined they have allowed a two to three per cent increase in tailing thickener underflow density to be consistently achieved, which has allowed greater water recovery. As a result, the processing plant has been able to operate at higher throughput rates when required, with greater water availability in the process plant recirculating system and a reduction in occurrences of the plant being æslowed downÆ due to water supply shortfalls. Both projects have also delivered a significant reduction in flocculant usage.CITATION:Weidenbach, M and Lombardi, J, 2012. Tailing thickener operability and control improvements at Prominent Hill, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 137-142 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 29, 2012

At the beginning of the seventies pre- drainage of methane was introduced in West German coal mining in order to reduce the gas emission from the worked seam. After three pilot tests on the "Rheinland" Colliery (86 boreholes in seam "Prasident"), "Bergmannsgluck/ Westerholt" Colliery (23 boreholes in seam "Gustav") and "General Blumenthal" Colliery (27 boreholes in seam "Hugo" and 170 boreholes in seam "Karl") systematic large scale tests with extended investigations were carried out un the "Rheinland" Colliery (127 boreholes in the seams "Anna", "Blucher", Prasident"). During this time an analogous test was carried out on the "Consolidation" Colliery (21 bore- holes in seam "B"). In these studies and tests the technical feasibility, efficiency and economy could be proved, so that pre-drainage of methane starts spreading. On the "Rheinland" Colliery pre-drainage has become common practice in gassy seams. Mainly two points impede a faster spreading of method: 1. in many cases the necessary requirement, that one or both of the gate roads should ire driven 6 to 12 months before the face is worked, is missing. This is mainly due to the difficulty of retreat mining in passe seams.

Jan 1, 1982

By Dolan P

Various operating practices have been developed over many years to ensure safe and efficient production from the 1100 orebody. Some of these practices are described.

Jan 1, 1982

By R Winterberg

Concrete is a well established and reliable construction material for the permanent lining of tunnels, but shows some weak performance characteristics, which can be overcome by the addition of specialised fibre reinforcement. This paper addresses the particular performance design requirements of segmental linings, discussing the improvements of fi bres on concrete properties. Focus is made on the beneficial effects of fibre reinforcement on the cracking behaviour and the toughness performance, providing a safe and durable tunnel lining.Not only the mechanical performance of fibre reinforced concrete (FRC) for segmental linings, but also the durability of the linings has gained growing attention among the designers and consultants. Especially tunnel linings with exposure to media with corrosion potential, such as wastewater sewer tunnels or desalination plant outfall tunnels, have high requirements on their durability. The design of these structures must provide a comprehensive study of durability aspects. Fibre reinforcement can substantially improve the durability of concrete.Research has been carried out on the cracking behaviour of concrete. The beneficial effects of steel fibres on the cracking behaviour reduce the permeability by reducing the flow paths within the concrete. Crack bridging steel fibres create necking effects in bending cracks, leading to earlier closure of the cracks. Further, steel fibres create particular crack formations, which lead to a substantial reduction of the fl ow rates through separation cracks. The results also show that considerable cost savings can be achieved using FRC, as the thickness of the linings can be reduced.The durability design issues will be addressed and underlined by a case history on the Hobson Bay sewer tunnel in Auckland, New Zealand.

Mar 8, 2011

By R Berry, J Lett, C L. Harraden

"In the past decade, increased processing capacity combined with precision robotics in high resolution spectrometers has resulted in a new generation of high-speed hyperspectral core logging systems. The application of these multisensor automated platforms provides a key advancement in the characterisation of metal resources. The development of this technology has allowed for comprehensive, drill core-based, mine-scale rock mass characterisation studies. Here we propose a new method for the extraction of parameters that seek to more accurately quantify ground conditions, including quantified rock mass rating (RMR) and the Rock Tunnelling Quality (Q) Index. Data inputs include rock quality designation (RQD), number of joint sets, joint roughness, joint alteration and joint spacing. Geologists and geotechnical engineers have historically collected these inputs by manually logging drill core. With automated core scanning technologies, these parameters can be estimated from the acquired image data and used to objectively calculate RMR and Q-index values for oriented core.Corescan is an automated hyperspectral core scanner that uses a 3D laser profiling system to measure the height of the surface of drill core. This technology allows for rapid core analysis to produce detailed fracture and rock condition data. Through an integrated geometallurgical approach, the proposed methodology will test the accuracy of joint measurement using the height profile Corescan data from oriented drill core. This will be combined with joint roughness and alteration mineralogy measured from the hyperspectral images to calculate the RMR and the Q-index continuously downhole. The values obtained can then be compared to the traditional, manual geotechnical log data. If the precision is sufficient, these techniques can then be applied site-wide to automate the collection and modelling of key ground condition classification indices across an entire deposit. Compared to the laborious manual geotechnical logging procedures that currently form the industry standard, utilisation of core laser profile data and high resolution red-green-blue (RGB) images provide an opportunity to collect large volumes of consistent geotechnical data, which can increase the efficiency and accuracy of deposit scale geotechnical models.CITATION:Harraden, C L, Berry, R and Lett, J, 2016. Proposed Methodology for Utilising Automated Core Logging Technology to Extract Geotechnical Index Parameters, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 119–124 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By S Slouka

Airborne rock dust poses serious long-term health complications to workers in the underground mining and civil environment where rock excavation is utilised. During drilling, airborne rock particles are immediately released into the breathable environment where additionally, the settled dust can be reintroduced into the air further down in production. The purpose of this study is to build a characterisation suite of dust particles such that underground operations can implement more appropriate dust suppression and mitigation techniques in accordance to pick wear. Therefore, concrete is cut to create a preliminary dust characterisation baseline, where future cutting tests will be performed on limestone and sandstone rocks.In this study, three conical pick wears (new, moderately worn, and fully worn picks) are used to generate dust from a concrete block and characteristics are statistically compared between the dusts. Airborne respirable particles are collected during cutting and deposited fine material, orparticles left on the surface of the block, are collected after cutting. The dusts are then analysed through standardised methods, field emission scanning electron microscope image capture with image analyses, and laser diffraction methods. Findings reveal that the worn pick generated thehighest concentration of respirable dust, all picks generated dust containing quartz, the three picks generally generated respirable dusts with similar particle shapes (in terms of roundness, roughness, and aspect ratio), and the worn pick generated the largest deposited fine material particles.

Oct 12, 2022

By M Chen, Q D. Gao, Y G. Hu, P Yan, W B. Lu

The safety and stability of construction structures are often affected by blast-induced waves. Investigating the generation mechanism of shear wave (S-wave) during blasting is important, because it has a strong effect in blasting damage. In this paper the generation mechanism and verification of S-wave was studied analytically and numerically. Under the finite velocity of detonation (VOD) of cylindrical charge or the compression wave (P-wave) communicating with the interface of different media during the propagation, the generation mechanism of S-wave was analysed. Propagation of blasting wave in cylindrical charge was simulated with the elastic model, and the generation of S-wave induced by finite VOD was proved. To compare with different numerical methods in simulating the generation of S-wave, the blasting process of instantaneous detonation was simulated by using the elastic model, elastic-plastic model and smoothed particle hydrodynamics and finite element method (SPH-FEM) coupled model. Results demonstrate that the S-wave could not be found in middle section of the charge if the elastic model is employed. But when using elastic-plastic model and SPH-FEM coupled model, the generation of S-wave could be verified. Under the SPH-FEM condition, the amplitude of S-wave is larger and the arrival time difference between P-wave and S-wave is closer to theoretical results.CITATION:Gao, Q D, Lu, W B, Hu, Y G, Chen, M and Yan, P, 2015. Comparison of the generation of shear wave with different simulation approaches, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 79–88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J Vann

The philosophical context of many activities in mine geology can be an important lever in adding value to operations. For mine geologists (including resource and grade control geologists) we argue that the tasks of problem formulation, observation and data collection, interpretation and modelling invoke various philosophical considerations whether the practitioner is aware of them or not.Constructing testable models to explain reality is the definitive aspect of any activity claiming to be ‘scientific’. A primary goal of mining geology is to build models that accurately predict reality to an acceptable degree and these include litho-structural, stratigraphic, grade control, resource or reconciliation models. What’s more, in mine geology we are often able collect additional drill samples or access new underground openings, for example, that can provide relatively rapid feedback on how predictive, and therefore useful, our models are. In this paper, we describe the key philosophical frameworks proposed for conducting scientific investigations, including falsification, the method of multiple working hypotheses and structural concepts of scientific theory. The strengths and weaknesses of these approaches are discussed and an attempt is made to relate them to activities undertaken by mine geologists. Common perceptions of what constitutes the scientific method have been dominated by how scientists do experimental physics and chemistry in particular. There are very important differences in the types of problem confronted in these experimental sciences compared to the ‘historical sciences’, such as geology, where the processes studied are unique and only evidential traces of past events are available. The philosophical implications of attempting to validate numerical geological models, such as resource estimates are also briefly considered.Some practical conclusions are drawn about how mine geology activities can be better implemented if practitioners are cognisant of the importance of philosophical considerations when attempting to gain new knowledge through a scientific investigation. We believe that the implications for creating additional value to a project or operation can be very significant when geology is applied by a practitioner with an understanding of the philosophical basis of the activities we think of as constituting a scientific investigation.Remember that all models are wrong; the practical question is how wrong do they have to be to not be useful? (Box and Draper, 1987, 74 p).The demand that theories be highly falsifiable has the attractive consequence that theories should be clearly stated and precise. If a theory is so vaguely stated that it is not exactly clear what it is claiming, then when tested by observation or experiment it can always be interpreted so as to be consistent with the results of the test. (Chalmers, 1999, 67 p).

Aug 22, 2011

By K Young, M Martin, D Payne

This paper outlines the evolution of managing high consequence risk scenarios in BHP Coal, with particular focus on managing the stability of an endwall that is adjacent to a public infrastructure corridor running through a Central Queensland coalmine. BHP Coal developed a Geotechnical Consequence Register after industry failures identified shortcomings in traditional risk assessment practices. Traditional risk assessments consider the consequence and likelihood of a geotechnical event occurring under normal operational conditions. As such, the risk rating for a high consequence, low likelihood failure may fall within the acceptable range, even where a lack of meaningful geological data exists due to the area being off lease or outside of mining reserves. The Geotechnical Consequence Register lists all geotechnical failure scenarios of high consequence, identifies if current controls are adequate, and highlights if specific Geotechnical Management Plans are required. This case study reviews a failure scenario that was identified through the geotechnical consequence register. The scenario had previously been considered low likelihood and subsequently driving a low risk; however, the likelihood ranking was impacted by a lack of geological data outside of the mining lease and predominately informed by an acceptable historical slope behaviour. Additional exploration identified previously unmapped faulting which increased the risk rating. The requirement to develop a specific management plan resulted in an increase in the required factor of safety, design changes, the implementation of additional monitoring and a corresponding monitoring Trigger Action Response Plans (TARP). In the case study area, the initiation of a geotechnical instability was identified early through the increased monitoring program. The instability was successfully managed and any impact to the infrastructure corridor off lease was prevented. BHP Coal has used the Geotechnical Consequence Register for several years to identify and assess high consequence geotechnical failure scenarios. In some areas this has justified additional exploration, more stringent design acceptance criteria and an increased level of geotechnical monitoring. The process has been successful in ensuring that geotechnical risk is controlled in areas that often receive less attention than active production areas.

Nov 29, 2022

By D Brown, K Markovic

The world is becoming an increasingly complex environment to operate within. Adoption and evolution of technology is occurring at a rapid pace and operating spaces are growing in interconnectedness and interdependency. In mining this is evidenced by the large-scale adoption of autonomous machinery, intelligent systems, Internet of Things (IoT) devices, and robotics to realise benefits in optimisation, productivity, and safety. To enable continual delivery and growth in operational performance, and to realise the aforementioned benefits, a new approach for managing mining and metals is required (Mining Review Africa, 2023). This means that an already talent constrained workforce must learn to manage the complexity inherent, evolving, and growing in the environment (Abenov et al, 2023). A key skill that needs to be further developed and deployed to combat these challenges and to enable robust problem solving is that of systems thinking, which is already practiced in pockets within the mining industry. Experience and learning can be leveraged from other industries and their application of systems thinking to ensure that focus is maintained on areas where the benefits from which will be optimised. With targeted application, a workforce capable of effective systems thinking can be the catalyst to optimisation across mining organisations.

Sep 1, 2024

By K Zunica, A R. Penney

The principles of three-dimensional geological modelling are well understood and routinely used. Sample data is collated and geostatistical tools used to ensure that sample data is suitable for its end use, which is typically a block model that is appropriate for mine planning. What has become increasingly apparent is that physical rock properties and geotechnical parameters need to be incorporated into the three-dimensional geological model to create an integrated mine model.The approach to the collection of geotechnical information is not as highly prescribed and controlled as collection of geological data. Commonly, the geotechnical data set is incomplete and inconsistent, with little consideration of what the end use will be by those collecting the data, or how the geotechnical data might relate to the geological data. In some cases, specific geotechnical investigation programs are completed, yet correlation between those programs and previously collected data is rarely undertaken to the same level of diligence as found in the geology field.There are some obstacles that need to be considered when attempting to incorporate geological parameters, such as grade, lithology, and geological domains with geotechnical information such as rock quality designation (RQD), rock mass rating (RMR), rock strength, and geotechnical domains into the same three-dimensional block model. Interpolation or geostatistical estimation methods used for grade estimates might not be appropriate for many components in rock characterisation, particularly search geometries. A number of examples are provided to illustrate issues underlying some of the data collection procedures, and their effects on three-dimensional geotechnical modelling.The example presented attempts to highlight generally observed shortcomings in the collection of geotechnical information, parameters which need to be considered when combining geological and geotechnical data into the same model, and the benefits of having a combined block model from the beginning of a project.CITATION:Zunica, K and Penney, A R, 2014. Integration of geological and geotechnical data for three-dimensional modelling, in Proceedings Ninth International Mining Geology Conference 2014 , pp 291–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By S Thomson, G Rigby, J Norgard, D Wilkinson

Bulk explosives provide the energy to move a rock mass and reduce it to an optimal size (fragmentation). The intensity of energy needed depends on several factors including a customer’s geology and end objectives. An energy mapping tool has been developed to help customers to determine their bulk explosive needs based on these objectives.At one end of the energy map dealing with high-energy products, a new range of bulk explosives products for surface mining have been developed. With these products, it is possible to provide blast designs with up to nearly triple the relative bulk strength (RBS) of ANFO, and address primary focus areas for mining operations, including the reduction of drill and blast costs, improvements in production rates, better face advance through improved broken stock management, better drill productivity, improved milling efficiency and lower energy costs in surface mines.In this paper, field trial results from the first level of new high-energy products are presented. These products have an RBS 2.25 times that of ANFO. Industry variations of a smaller diameter (89 mm) pumped product for civil quarrying applications, and for large diameter (311 mm) hard-rock metalliferous mines are presented. For both cases, the run-of-mine fragmentation levels obtained with the new bulk explosives are contrasted with the fragmentation profile generated with the currently accepted product range applied in similar geological conditions. The new products show increased fragmentation across the measured size distribution, with reduction in P50 values of 20 and 37 per cent over the currently used product for the 311 mm and 89 mm diameter blastholes respectively.CITATION:Wilkinson, D, Rigby, G, Norgard, J and Thomson, S, 2015. Higher energy bulk explosives – matching products to rock types using an energy map concept, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 579–584 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By L Tatnell, R Mackay, A Tolooiyan

The multi-reversal direct shear test (MRDS) method is commonly used to measure the residual shear strength of soils. However, when the standard direct shear (DS) apparatus is used, the MRDS method is prone to two major sources of error: load cap tilting and specimen loss. These two sources of error can cause erratic behaviour in the residual shear strength curve, making it difficult or even impossible to determine the correct residual shear strength value of the specimen being tested. This paper presents the results of new modifications to the standard DS apparatus that prevent load cap tilting and specimen loss. Consolidated drained testing was performed on highly-over consolidated cohesive soil samples from a Latrobe Valley open pit mine, with results obtained from the modified DS apparatus showing a great improvement in the residual shear strength profile compared to those obtained using the standard apparatus. Large numbers of reversals (up to 14) conducted on a single specimen in the modified DS apparatus showed no notable load cap tilting and no specimen loss occurred. The modifications are easily applied to the standard DS apparatus, and analysis and correction of the data are simple.CITATION:Tatnell, L, Tolooiyan, A and Mackay, R, 2014. Measurement of residual shear strength using a modified direct shear apparatus, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 425–434 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By T M. Campos, H A. Petit, L M. Tavares, R Olympio

Much practical experience has been gathered in the last 30 years of application of high-pressure grinding rolls (HPGR) integrated with ball milling in size reduction of fine iron ore concentrates. The company Vale S.A, in Complexo de Tubarão (Brazil), was one of the pioneers applying the technology prior to pelletisation with an outstanding size reduction energy efficiency in the circuit and a significant increment in the specific surface area of the product. Recent studies by the authors demonstrated benefits of modelling and simulation to improve the performance of HPGRs in this particular application, with the model being able to describe HPGR performance under different operating conditions and under variations of feed size distribution. Despite these important advances, this modelling approach has only been used offline and under steady-state conditions. The present work applies the modified Torres and Casali model proposed by the authors in pseudodynamic simulations. The ability of the model to predict the characteristics of the product in real-time is evaluated using data available online for the pellet feed preparation circuit. Results demonstrated the model capabilities to map the physical operation and give a realistic representation of the process. Additionally, the model is demonstrated to be able to support the pellet feed production by providing extended real-time information of the process, making it a useful tool for improvement of the operational strategies and process stability.

Aug 24, 2022

By L Y. Yang, Z Wang

This work presents the fundamental properties of CITIC magnetite concentrate and its performance in pelletising and sintering. CITIC concentrate has been widely used in pelletising to produce pellets for blast furnaces. It is also used in sintering to benefit from its sintering performance. CITIC concentrate has excellent balling properties owing to its size distribution, particle surface properties, large specific surface area and balling index, leading to strong green pellets and product pellets. When used in sintering at appropriate levels, sinter bed permeability improves, productivity is increased while coke consumption reduces, and sinter strength improves.

Nov 8, 2021

Employing gravity recovery for coarsely liberated gold and sulfide ores has potential to lead to a signifi cant reduction in the energy required for comminution and ultimately can have a significant impact on gold processing. Most of the recognised metallurgical tools at our disposal currently have been designed around recovery of relatively finely ground minerals. In order to change the paradigm of fine grind for liberation, a new set of tools need to be recognised that are capable of separations in the coarser size fractions. Some of these tools already exist and some need to be developed but the key is the way in which the fl ow sheets are arranged. A very strong understanding is required in the existing tools and their capabilities before these new flow sheets can be optimised. Only when we understand the existing gaps in technology can we start to fill these positions with new candidates. Many ores when crushed liberate their gold bearing minerals at coarser sizes than current practice would suggest (Figure 1). In order to characterise this response in ores it is necessary to utilise some new techniques in the lab such as gravity separation and ore sorting at the sizes greater than 15 mm followed by gravity recovery on fractions from 15 mm down to 150 ¦m. The most difficult range has been the mid-sized fraction from 4.0 mm down to around 150 ¦m. This is the size range in which many ores show economic liberation starting to occur and coincidentally this is the range in which many commonly used metallurgical processes reach their operational limits due to physical constraints. Examples of these processes are flotation, hydrocyclones and whole ore leach in agitated tanks which are currently the mainstays of the processing fraternity. This is an ABSTRACT ONLY. No paper was prepared for this presentation.

Aug 1, 2010

By D A. F Oliveira, C J. Parker

The role of the virgin in situ stress field in tunnelling projects is well known in the Sydney area. The effect of in situ stresses is mostly considered through the use of published relationships that describe the in situ stress conditions as a function of depth. Considering the significant scatter in the data, it is evident that by adopting such relationships, the designers are assuming an average distribution of stresses with depth that is generally a reasonable engineering approach; however, when building a geomechanical model, the tunnelling or geotechnical engineer needs to account for the interrelationship between ground conditions (rock mass quality – fracturing, strength and stiffness) and in situ stress, which may explain part of the stress data scatter. This paper presents an alternative approach for interpreting in situ stress conditions, valid for both Sydney sandstones and shales that focus on such interrelationship between in situ stress and ground conditions.CITATION:Oliveira, D A F and Parker, C J, 2014. An alternative approach for assessing in situ stresses in Sydney, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 189–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By T Baumgartl, L Zhou, D Mulligan, L Huang

The rapid production and accumulation of mineral processing wastes in the environment can present serious threats to environmental quality and human health. Phytostabilisation with native plant ecosystems is, in many cases, a preferred option for rehabilitation of mine waste storage facilities. However, much of the literature has focused on species selection in short-term experiments to test their suitability under the often extreme chemical conditions in the wastes without addressing the fundamental requirements – ie hydrogeochemical stabilisation and functional root zones. As a result, successful examples of phytostabilisation of mine wastes such as base metal tailings have been rare, especially if success is defined as meeting the completion criteria of non-polluting and sustainable land system at rehabilitated sites. Conventional capping options to isolate reactive tailings/wastes by using physical break and/or sealing layers are often not reliable in the long term (particularly under semi-arid climatic conditions) and, in many cases, they may not be feasible in the field due to the large areas to be covered and the lack of adequate suitable materials at mine sites. By using sulfidic tailings as an example, we have proposed a new paradigm for phytostabilising mine wastes – ecologically engineered pedogenesis in tailings involving accelerated physical, chemical and biological weathering of tailings minerals to achieve hydrogeochemical stabilisation and the development of soil functions, soil horizons and functional root zones.Ecologically engineering functional root zones firstly requires controlling geochemical reactivity in the wastes (ie hydrogeochemical stabilisation), which can cause polluting effects in the root zone and plant toxicity. By means of ecological engineering, in situ weathering of primary minerals (eg pyrites) in tailings may be accelerated by adding functional materials (eg functionalised biochars and organic matter) in the waste slurry during the process of deposition. This will remove or diminish key risk factors (eg potential acidity in tailings and elevated soluble heavy metals) in the solid phase, before placing growth media for reconstructing root zones and transplanting/sowing target plant species. However, much of the acidity, soluble metals/metalloids and other salts would be transported out of the solid phase into the wastewater, which can be addressed by on-site water treatment facilities during mine operation. The trajectory and state of engineered pedogenesis in the weathered tailings may be manipulated to provide specific soil horizons within future root zones that are dynamically evolved toward fully functional soil subsystem within rehabilitated plant ecosystems.CITATION:Huang, L, Baumgartl, T, Zhou, L and Mulligan, D, 2014. The new paradigm for phytostabilising mine wastes – ecologically engineered pedogenesis and functional root zones, in Proceedings Life-of-Mine 2014 , pp 663–674 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

As this Seminar is on "Progress - Mining and the Environment", I am taking the liberty of extending my address beyond the scope implied by the subject, "Rehabilitation of Mined Land", with a preliminary discussion on broader economic issues relevant to "Progress and Mining in Western Australia" before discussing its effect on the Environments Western Australia is nearly one million square miles in area and has a population density of approzimately one person per square mile. Because of its vastness it has wider climatic variations than any other Australian State. The north is tropical and the south is in the temperate zone. The major portion of the State is an arid plateau with less than 10 inches of mean annual rainfall. The climate, rainfall and soil conditions of the South-West region are more favourable to agriculture than any other part of the State and consequently was settled first. The immediate need of the colonists being food and shelter, the early economy was based on farming and forest products.

Jan 1, 1971