Search Documents

By R W. Wilson, A R. Branch, T S. Pooe

The original bulk air cooling system at this particular mine made use of two water chilling refrigeration machines to produce peak cooling of approximately 12 MWR with a downcast air temperature of about 7°C; however, as the shaft is not used for transporting personnel, the opportunity existed to supply more cooling to the mine by lowering the downcast air temperature. An ice storage facility has been constructed and provides a range of opportunities in operating the system: colder air temperature sent to the shaft, enabled by using near-zero degree water produced by melting ice to cool the air; electricity time-of-use management, by shifting electricity usage out of peak tariff periods; and increased peak cooling capacity, by melting ice while chilling water. Ice is created in the storage facility at night while the ambient air temperature is low and then melted to produce cold water when required by the cooling process. An ice dam was constructed and serpentine stainless steel coils installed where the ice is produced; one of the refrigeration machines was converted to chill a glycol solution to subzero temperatures to create the ice on the coils; a plate heat exchanger was installed to allow the glycol chiller to act as a water chiller as well; and a third spray stage was added to the bulk air cooler to utilise the near-zero water. This paper describes the thermodynamic design, construction and performance assessment of the new system, which is unique, novel and represents the state-of-the-art of this type of cooling system and energy management.CITATION:Branch, A R, Wilson, R W and Pooe, T S, 2015. Novel use of ice thermal storage for energy management on a mine refrigeration plant, in Proceedings The Australian Mine Ventilation Conference, pp 185–192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By L Thorburn

In 2009, the Queensland Government developed a series of amendments to environmental authorities (EAs) for mines throughout the Fitzroy Basin in response to studies that assessed the cumulative impacts of mine water discharges in the basin. One of the key amendments was the requirement for all mines in the Fitzroy Basin to develop and implement a receiving environment monitoring program (REMP). The intent of the REMPs was to provide baseline information on the condition of the receiving environments of the mines and any impacts resulting from release of mine-affected water. Since this time, the requirement to complete a REMP has been incorporated into new or revised EAs for mines (including metalliferous mines) in other regions, as well as for other industries that discharge to natural watercourses (such as coal seam gas). This paper discusses the approaches that can be used to incorporate biological monitoring and direct toxicity assessments into REMPs. It highlights the importance of collecting biological data using sound experimental design principles to investigate whether releases resulted in environmental harm; and the use of monitoring data, coupled with direct toxicity assessments, for setting more realistic, site-specific trigger values and release limits (compared to the default guidelines such as Australian and New Zealand Environment and Conservation Council (ANZECC), which may not be appropriate to the region). Implementation of a robust REMP can maximise outcomes for both the proponents and the environment.CITATION:Thorburn, L, 2013. Receiving environment monitoring programs - making the most out of biological indicators and direct toxicity assessments for monitoring of aquatic ecosystems, in Proceedings Water in Mining 2013 , pp 143-148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Saghafi A, Kelly M, Williams R. J

A two year program of research into the feasibility of long-hole drilling for improved gas emission control has been undertaken at Appin Colliery. State of the art equipment was employed involving cableless electronic surveying and down-hole motor drilling. The project involved the drilling of 1000 m long, in-seam boreholes in the Bulli seam and boreholes of similar length drilled cross measure and then in-seam along the underlying Balgownie seam. A new concept for gas drainage was defined, employing long-holes for both predrainage and post drainage.

Jan 1, 1988

By R Millar

A frequent challenge in mine water management and mine design is estimation of precipitation and extreme rainfall given a short record of site meteorological data. For remote mine projects, typically only a few years of rainfall data are available, which is far too short for estimation of design rainfall event, such as the 1-in-100 year storm. A frequency-paired approach is presented for comparing daily precipitation records from a mine site with a long-term regional station and provides the basis to transpose the long-term record to the mine site. This allows a long-term synthetic precipitation record to be developed for the mine site that can be used to undertake site water balance studies, determine pond storage requirements, assess water supply options and address other surface water management issues. Conventional approaches are based on chronologically-paired data and when applied to daily data generally yield poor correlations between stations. In the frequency-pairing approach, statistical distributions (two-parameter gamma distribution) are fit to daily data from two stations and used to calculate daily and extreme precipitation values for the short-term site (which is typically a mine or other project site). The method is demonstrated using data from two meteorological stations located along the south coast of British Columbia, Canada. Use of a fitted two-parameter gamma distribution (or other distribution) provides a sound theoretical approach to comparing precipitation data from two sites and the basis for transposing a long-term record to generate synthetic precipitation series and extreme rainfall values at mine sites.CITATION:Millar, R, 2013. A statistical approach for deriving project design rainfall, in Proceedings Water in Mining 2013 , pp 273-276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By J Allen, B Oats, S Palaniandy, M Lollback

The Julius Kruttschnitt Mineral Research Centre has conducted an intensive VertiMill® (VTM) survey program at the Cannington mine concentrator as part of the ‘collaborative research in stirred milling technology’ program funded by Metso Minerals. Since 2003, Cannington has progressively added grinding capacity into the circuit through VTMs operating in secondary and regrinding duties. Cannington was one of the first mines to adopt this technology in secondary duty by installing two VTM-1500-WBs as part of a capacity expansion to produce sub-100 µm rougher feed. Subsequently, an additional VTM-800-WB was installed in the lead regrind circuit to prepare sub-20 µm cleaner stage feed.Several surveys were carried out to evaluate the VTM performance over a range of changed conditions. Among the key changes in operating variables were circuit power draw, feed rate and water addition to the bottom of the mill. The average specific energy for secondary duty was 3.7?kWh/t. The lead and zinc regrind mills consume 8.1 and 15.3 kWh/t respectively. Generally, the VTM installations have successfully prepared feed for rougher and cleaner circuits by reducing the top size into the floatable regime with steeper particle size distribution, which has led to enhanced recovery. The survey results show the success of VTM installations in secondary (receiving feed from autogenous circuit) and regrind duties.CITATION:Palaniandy, S, Powell, M S, Hilden, M, Allen, J, Kermanshahi, K, Oats, B and Lollback, M, 2014. VertiMill® performance updates in secondary and regrind duties at Cannington mine, BHP Billiton, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 263–272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By H Weitz

Bateman Engineering provided process technology and engineering design to China Yunnan Metallurgical Company (CYMCO) for a 30 MW DC furnace for the production of high-grade titanium dioxide slag.Following the successful commissioning of the furnace during the latter part of 2009 and the first quarter of 2010, a period of adverse circumstances resulted in having to operate the furnace without feed and at a low power input for a period of time. When normal feed resumed, a layer of solid material was detected on the slag-iron interface during sounding measurements. The condition of the iron was also significantly altered. The iron temperature was much higher than the design value, but the carbon content had decreased to such an extent that a large amount of iron solidified in the furnace, which made iron tapping very challenging. The slag temperature was increased in order to melt the solidified iron. However, severe sidewall damage resulted, which finally led to a burn-through. A number of samples were taken from the slag that remained in the furnace. These samples were analysed to determine the chemistry and phase profile throughout the slag bath. The mechanisms of formation of the high melting-temperature phase on the slag-iron interface are discussed, as well as procedures that can be applied to prevent a recurrence of this phenomenon. Some recommendations are made for instances when furnace feeding is interrupted for an indeterminate period.

Oct 5, 2011

By R P. Varden

This paper looks at the design of the Bentayga raisebore with subsequent back analysis using a LiDAR survey. A search for LiDAR raisebore assessment publications shows little work has been done on this subject. The paper examines the empirical design and RS2 modelling assessment with the bored condition. The high resolution of the LiDAR enabled mapping of weak structures that were located on the geotechnical investigation hole the orientations of which could not be determined. In addition, the scan showed were water ingress was occurring, potential stress overbreak and structural controls on stability. The LiDAR results were able to confirm no additional support work such as a shotcrete liner is necessary. The LiDAR results have been analysed in one metre increments as volume of overbreak against the empirical stability criteria (McCracken & Stacey 1989). The future use of LiDAR mapping over a range of rock mass conditions will provide quantification of the established empirical assessment improving its reliability. It is also a useful and accurate tool to monitor long term stability of a raisebore due to stress change or ore pass due to wear.

Mar 15, 2021

By F M. Weir, M Fowler

The design of excavations in rock must, implicitly or explicitly take into consideration the influence of small- and large-scale geological structures. For most sites the complexity of a fractured rock mass is best captured using a 3D fracture system model based on field data. A discrete fracture network (DFN) approach involves stochastic modelling of the ‘smaller scale’, nondeterministic structures. For slope stability or tunnelling projects DFN modelling provides a valuable geotechnical tool for characterisation of a rock mass and identification of likely failure mechanisms.This paper presents a suite of the DFN modelling undertaken for the design of a large open pit in Australia. The proposed pit is to encounter a 160?m thick, high strength, sheared shale unit, which overlies a crystalline basement. DFN modelling was undertaken separately for both the shale and basement units. While the model inputs and development for each unit are briefly presented, the focus of this paper is on the various applications of the DFN modelling.A key advantage of the DFN approach for design studies is its probabilistic application to structural analyses and results. Multiple realisations of the same model were generated for both the shale and basement units, with the stability analysis carried out on each iteration. The generation of a large number of DFN models and analyses allow assessment of wedge volume, factor of safety and proportion of unstable slope for a range of conditions. The DFN modelling at the case study site was also utilised for a number of other purposes. For example, investigation of likely fault lengths in the shale unit and combined rock mass and defect failure. The development of this tool has been influential in improving our understanding of fracture networks for excavation design.CITATION:Weir, F M and Fowler, M, 2014. Rock mass characterisation and analysis for excavation design – a discrete fracture network approach, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 445–456 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

EnergyAustralia is a state-owned corporation in the state of New South Wales, whose responsibility includes ownership and management of an electricity distribution network. Expansion of the high voltage distribution network in the Sydney central business district (CBD) includes the requirement to run an additional five 132 kV feeders over 1.7 km from south of the CBD to a new 132 kV substation in the northern section of the CBD. A driven tunnel is currently being excavated in Sydney sandstone beneath Darling Harbour to contain the new 132 kV feeders. Tunnel construction methods involve both roadheader and tunnel boring machine (TBM) excavation. This paper describes the design development of the cable tunnel, discusses the use of a geotechnical baseline report as an integral part of the contract documentation and provides an update of the current construction works.  

Jan 1, 2008

By T Ireland

The Project Hobson tunnel excavation was the first use in New Zealand of an earth pressure balance (EPB) tunnel boring machine (TBM). The tunnelling on the project was very successful and break-through was achieved three weeks ahead of program, demonstrating that tunnelling can be undertaken in Auckland with a high degree of cost certainty.Project Hobson involved the replacement of an existing 90 year old above ground sewer that crosses Hobson Bay in Auckland, New Zealand, and which had reached the end of its economic life, with a 3 km long, 3.7 m internal diameter segmentally lined bored tunnel. The NZD$ 118 M project has provided several environmental benefi ts to the Owner, Watercare Services Ltd and the local community:· provide capacity to meet projected growth in the region,· virtually eliminate wastewater overflows into Hobson Bay and the Waitemata Harbour, and· remove an obtrusive visual feature and open up the bay for recreational purposes.Auckland’s bedrock is a weak sandstone/siltstone (East Coast Bays Formation), subject to infilled paleovalleys. The geology in the region has been significantly influenced by volcanic activity; 49 volcanoes are present within 20 km of the city centre.The paper describes the design and construction challenges for the projects, including TBM performance, ‘sticky spoil’ management, and risks associated with basalt lava flows and two paleovalleys. The paper also highlights the reasons for the success of the project, including a rigorous approach to risk management during design, and effective planning during construction. Other useful data such as the effect on the watertable caused by closed face tunnelling, and ‘faceloss’ estimates derived from settlement arrays are included in the paper.Project Hobson also saw the successful implementation of a Geotechnical Baseline Report – one of the first uses of this type of document in Australasia.

Mar 8, 2011

By G Hancock, J Lowry, W D. Erskine, D Jones, T Coulthard, M J. Saynor, P Lu

An 8 ha trial landform was constructed in late 2009 at the Ranger Uranium Mine, located 250 km east of Darwin in the wet-dry monsoonal tropics of northern Australia. The objective of the trial, which comprises two surface cover types on a uniform two per cent slope, is to provide long-term data to guide the development by Energy Resources of Australia Ltd (ERA) of its landform closure strategy. The scope of the work program for the landform includes many aspects; however, this paper is focusing on run-off and erosion rates. The run-off and erosion rates are used to assess the long-term geomorphic stability by comparing measured with modelled export rates from a landform evolution model.Monitoring of wet season run-off is undertaken collaboratively by the Environmental Research Institute of the Supervising Scientist (ERISS) and ERA, on four purpose-instrumented 30 m by 30 m erosion plots. Continuous measurements are made in rectangular broad crested (RBC) flumes located at the outflow of each plot, of water level, turbidity (a surrogate for fine suspended sediment) and electrical conductivity (EC) (a surrogate for solutes). Each plot has a tipping bucket pluviometer located near the RBC flume. Bed load is collected monthly.This paper reports the findings of rainfall and bed load from the first two wet seasons (2009 - 2010 and 2010 - 2011) following construction. The field measured loads will be compared with the predictions made by the Cellular Automaton Evolutionary Slope and River (CAESAR) landform evolution model. Initial results indicate that predicted rates of sediment export from the CAESAR model are similar to measured export rates. This provides confidence in the capability of the model to predict stability of the future rehabilitated mine area, especially during the critical initial years following construction. CITATION:Saynor, M J, Lowry, J, Erskine, W D, Coulthard, T, Hancock, G, Jones, D and Lu, P, 2012. Assessing erosion and run-off performance of a trial rehabilitated mining landform, in Proceedings Life-of-Mine 2012 , pp 123-132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By M Astorga, J Jackson, J Gaunt

The Ban Houayxai mine (BHX) is a relatively low-grade, low-cost, open pit gold-silver deposit in Laos operated by Phu Bia Mining, a subsidiary of PanAust. The ore production rate at BHX is 4.5 Mt/a, with direct tipping to a semi-autogenous grinding/ball mill circuit with a carbon-in-leach process plant. Approximately 100 000 oz of gold is produced per annum.The operation is located in mountainous terrain with minimal run-of-mine stockpiling. This results in limited capacity for blending from stockpile, with the mill instead reliant upon direct feed ex-pit. Since commissioning in 2012, the plant has seen significant variation in milling rates due to variability in the feed properties of the oxide, transition and primary ores. As part of an ongoing continuous improvement program, an integrated approach was initiated, focusing on maintaining and enhancing production in the future as the proportion of harder primary ore increases. This will specifically focus on direct blending from the loading face using the ore properties and blast fragmentation to maintain mill throughput.This approach was based on the concept of physical assets management, commencing with improving information and knowledge of the condition of the orebody through modelling the characteristics, variability and performance of the feed for processes relevant to throughput. These models are used to support both mine and process plant production planning.The key ore feed characteristics and parameters modelled for the life-of-mine are blastability index, powder factor, crushability or impact resistance and grindability. These predictive spatial models were based on the data from diamond drill holes used in resource definition and geotechnical drilling programs by integrating geotechnical, geological, geochemical and metallurgical data.At the early stages of implementation, the models are being utilised for ore blending decisions to provide guidance and support for budgeting, long-term mine planning, blast design for mill feed and providing the mill with an expectation of performance.CITATION:Jackson, J, Gaunt, J and Astorga, M, 2014. Predicting mill ore feed variability using integrated geotechnical/geometallurgical models, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 165–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By H Wright

Black Rock Cave (BRC) is a sublevel cave which was developed in 2018–2020 and has been in production since November 2020. BRC is part of the Mount Isa Mines complex and extracts a leached orebody comprising of high-grade chalcocite ore, situated below the historic Black Rock Open Cut workings. The mine is owned by Mount Isa Mines and operated under contract with PYBAR Mining Services. In 2021 a number of rockfalls occurred throughout the mine and were increasing in frequency. This culminated in a major rockfall on the decline in June 2021, after which the decision was made to withdraw all persons from the mine, initiate rehabilitation and conduct further investigations to deduce a safe method to provide long-term support. The rockfall investigations have shown that the corrosive nature of the highly leached rock mass can consume a split set in less than 18 months. A review of potential corrosion resistant ground support methods concluded that steel split sets have a safe lifespan of six months at BRC, and that all workings must have corrosion resistant support installed prior to exceeding the safe life of the friction bolts. The review recommended the use of 4 m cable bolts as the most suitable method of corrosion resistant support. This new support system, and the requirement to rehabilitate all mine workings within the leached orebody, had an impact to the schedule and an effect on both equipment and manning levels at BRC. Accelerated jumbo rehab allowed access to the production levels within two months of the rockfall. Cable bolting then followed the jumbo bolting in all leached areas. The direct impact has been ten months of reduced production, due to night shift closures of the decline to enable cable bolting. The impact to the mine has been minimised by the small flexible team that enabled the mine plan to change rapidly and often to accommodate the challenging conditions. In less than two months from the rockfall event, production had resumed. Within ten months of concluding that the mine required; full rehabilitation, a new support system and a full re-schedule, normal mining operations had restarted, with pre-event productions rates being achieved.

Mar 29, 2023

By Waterhouse BJ

Occurrence data of Tastubian,Sterlitamakian, and Aktastinian (all of Sakmarian Stage of Early Permian) brachiopod genera are analysed by Q-mode cluster analysis, principal component analysis, and discriminant analysis based on presence or absence of genera. Five faunal provinces and their corresponding generic associations persisted throughout the Sakmarian Stage. The additional Sasian Province incorporating the Lhasa and Shan-Thai terranes became recognisable in Sterlitarakian and strengthened in òAktastinian, implying a Tastubian-Sterlitamakian rifting event, followed by subsequent northward drift and divergence from Gondwana, and convergence with Laurasia. The nature of Permian 'Tethys' is discussed on the basis of faunal migration and abrupt changes of faunal provinciality in Lhasa and Shan-Thai terranes.

Jan 1, 1990

By E Widzyk-Capehart, C Hölck Teuber, S Steffen, V Rivero, O Fredes, E Sanchez, I Pedemonte, N Gonzalez

This paper summarises the research, development and initial application of a sensing platform that has the potential to monitor subsurface deformations, pore pressure and other variables simultaneously to gain a better understanding of rock mass behaviour. The platform is based on Networked Smart Markers (NSMs) devices, which, with their ability for wireless communication between individual sensors and the possibility of real-time data acquisition and processing, will assist in the development of predictive tools to better assess rock mass behaviour.A good opportunity to implement this technology is in the specific application of transitioning from an open pit mine to an underground caving operation. One of the key elements to maintaining the mining business during such a transition is having a good understanding of the unique geotechnical conditions of mutual influence created during the open pit to underground interaction. The knowledge acquisition will require the implementation of a robust platform for geotechnical monitoring, which could be enhanced by incorporating the NSMs. The integration of sensors within the NSMs would enable the collection of additional data about rock mass behaviour (ie caving propagation and crown pillar fracturing), which could be used to improve the management of mining operations and, specifically, allow the development of reliable predictive tools based on the data collected.CITATION:Widzyk-Capehart, E, Hölck Teuber, C, Fredes, O, Rivero, V, Sanchez, E, Pedemonte, I, Gonzalez, N and Steffen, S, 2016. Understanding rock mass behaviour through the development of an integrated sensing platform, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 275–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J D. Tolley

The shift towards clean energy technologies is having a significant impact on the mining industry, with the demand for minerals such as copper, nickel, cobalt, lithium, manganese, and graphite increasing exponentially. To meet the goals of the Paris Agreement, mineral requirements for clean energy technologies would need to quadruple by 2040, and to achieve net-zero globally by 2050, mineral inputs in 2040 would need to be six times more than today. The most significant driver of mineral demand is electric vehicles (EVs) and battery storage, with lithium seeing the fastest growth, and copper demand doubling over the same period due to the expansion of electricity networks globally. The demand for these minerals is expected to rise significantly as investments in clean energy technologies continue to grow in the future. As the world moves towards a decarbonised economy, the minerals industry is under increasing pressure to reduce its environmental and social impacts and meet the increased demand for minerals. Mining companies are facing additional challenges due to the depletion of near-surface mineral deposits globally, with more mines transitioning from open pits to underground. The transition to underground mining requires the right strategy to economically access deeper mineable inventories and to keep up with future clean energy technology demands to achieve net-zero globally by 2050. One key way to achieve this is through decarbonisation using ‘green’ mining technologies such as replacing current primary diesel mining fleets with battery electric vehicles (BEVs). However, these measures through electrification overlook the bigger opportunity to maximise the socio-economic returns from the mine while also reducing the overall carbon footprint. Corporate cut-off grade policy is one of the most significant influencers on the total environmental and social impacts of the mining industry. The purpose of a corporate cut-off grade policy is to implement strategies aligned with achieving all the mining companies’ corporate goals, with decarbonisation targets becoming a primary driver for mining companies. Table 1 shows the evolution of cut-off theory with the increasing number of dimensions and driving inputs per iteration.

Aug 2, 2023

By Manca PP, Lassandro R, Caranassios A, Massacci G, Ciccu R

The paper discusses the state of the progress reached in the development of the diamond wire tool for cutting hard rocks. To the advances of this relatively new technology a substantial contribution has been provided by the research being carried out at the University of Cagliari on samples of granite rocks from different Sardinian stone quarries. On the basis of field experiments and laboratory test data, the mechanism of diamond wire cutting has been assessed. In particular the influence of the rock features and operational variables on tool performance (cutting rate and bead wear) has been Elucidated.

Jan 1, 1992

By M Bloss, B Roberts

BHP Billiton Olympic Dam required a well-tested software product suitable for strategic optimisation and scheduling of options for a potential underground mining project. The company has a standard software package called Blasor® that is used for open pit optimisation of complex deposits such as iron ore, copper-gold-uranium and silver-lead-zinc. It applies a mixed integer programming formulation (MIP) to produce conceptual pushback designs and an optimised pushback sequence. Schedules can then be run on the resulting mine designs. Existing pushback designs can also be imported into the model and an optimum schedule generated. One of the key advantages of Blasor is that multiple strategic mine schedules can be quickly generated according to the various scenarios, options and constraints that are being investigated.It was realised that Blasor, if carefully configured, could be adapted for use in underground planning. The concept of using Blasor as an optimiser for underground strategic scenarios is to represent the underground stope and development data in the form and structure of an open pit mine. In simple terms, underground stoping areas are modelled in the form of pushbacks (phases) with vertical walls. The phase dependency tools in Blasor are used to link mine blocks and their access development drives. These underground phases are imported into the optimiser. Artificial block models are constructed using stope design tonnage and grade data at various fixed cut-offs. A variable cut-off grade model has also been developed using a method of parcels to represent each cut-off grade increment.So far, this approach has been successfully used to investigate the optimum stope design cut-off for various strategic options, the economic potential of a series of mining and processing configurations and to provide guidance on the optimum sequence for developing and mining the various stoping blocks in the resource. Examination of the results has highlighted the most suitable development paths for more detailed study.CITATION:Roberts, B and Bloss, M, 2014. Adaptation of an open pit optimiser for underground strategic planning, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 249–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By N S. Weerasekara, S Town, E Lessing, J A. De Torres

Philsaga Mining Corporation (Philsaga) had three main aims in converting their lining system from steel to metal cap. They wanted to increase mill availability, minimise localised high wear and optimise particle breakage to deliver increased efficiency within the milling circuit. Combining Discrete Element Method (DEM) modelling and empirical interpretation of liner wear resulted in a rigorous approach to understanding the impact of mill liners on overall mill performance. This new understanding was subsequently used to not only derive a new lining design to optimise performance and thereby improve overall plant economics, but also to guide further lining development.In this work, detailed DEM modelling, developed from actual plant data, together with optimising liner design for wear paved the way towards the installation of a Metal Cap lining system at Philsaga’s Ø6100 mm SAG Mill. The results were a reported increase in SAG mill throughput of 16 – 20 per cent due to improved breakage through more efficient use of installed power, a reduction in localised high liner wear with overall increase in liner life and reduction in liner replacement time. Site also reported an increased gold recovery of 2 per cent which the improved breakage might have contributed to. This paper will present the design challenges and compare the Metal Cap lining systems performance against Steel lining system. CITATION:Weerasekara, N S, Lessing, E, Town, S and De Torres, J A, 2018. Metal cap versus steel lining system at Philsaga Mining Corporation’s Ø6100 mm SAG mill, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 653–664 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By M N. Mian

The Cayeli volcanogenic massive sulphide deposit is located in Black Sea region of Turkey. Cayeli Bakir Isletmeleri (CBI) was formed as a joint venture between Inmet (Canada) and Eti Holding (Turkey). CBI is processing complex copper/zinc sulphide ores. The Cayeli concentrator was commissioned in 1994, with a design capacity of 600 000 tonnes/year. The grinding circuit was a classical rod mill/ball mill combination. The rod mill was converted to a primary ball mill in May 1997. The reasons for conversion were to use mill power more efficiently and eliminate feed interruptions during rod charging. The grinding circuit now has a primary ball mill in open circuit, and a secondary ball mill in closed circuit with hydrocyclones. Classification was originally done in two stages with hydrocyclones. Both mill discharges were combined and pumped to a primary cyclopack having two, 500 mm diameter cyclones. Primary cyclone overflow was pumped to a secondary cyclopack for further classification. The secondary cyclopack had ten, 200 mm cyclones. Both unit underflows were fed to a secondary ball mill by gravity. The secondary cyclone overflow, typically 62-64 per cent passing 36 ¦m, at around 42 per cent solids (w/w) was fed to flotation circuit. In order to increase circuit capacity to 1 000 000 tonnes/year and to improve control over the grinding circuit, it was decided to convert the classification circuit from two stage to one stage. For this purpose, six Warman Cavex cyclones having 400 mm diameter were installed. Now, the combined primary and secondary ball mill discharge was classified in single stage with the Warman cyclones in closed circuit with the secondary ball mill. The cyclone overflow goes directly to the copper rougher circuit as flotation feed. The grinding circuit is producing a flotation feed of 70 per cent passing 36 ¦m. The change over to single stage classification at Cayeli was successful. A mill throughput of 1 000 000 tonne/year is being achieved with better control over classification, and improved grind size. Results and comparison between the two classification circuits are presented in the paper.

Jan 1, 2003