Search Documents

By F M. Senda

This paper highlights strategies used at the Barrick operated Kibali Gold Mine (KGM) to improve the drilling accuracy and blasting effectiveness for longhole open stoping. The mine currently uses Solo DL421 for the required stope drilling and has experienced an average deviation of 10 per cent. Strategies are raised to eliminate or at least mitigate the adverse effects of blasthole deviation and the impact of blasting induced effect at the stope faces including the stope crown. The integration of deviation trends in the design would allow the actual blastholes to be established within their required positions to then facilitate a proper energy distribution with the eventual production blasting. The implementation of stope undercutting reduces the hole length from 35 m to 30 m which in return decreases blasthole deviation by 3 per cent. Another strategy adopted to improve the drilling accuracy is to slow down the penetration rate with the use of several operating approaches, including 135 MPa percussion pressure, 65 rev/sec rotation speed and 17 MPa feed pressure. To this penetration rate, a constant k factor is applied to increase the rate when the bedding inclination is less than 45° from the horizontal or when the hole length is under 10 m. This reduces deviation by a further 4 per cent. Where the rock mass is highly jointed it is advised to use the average penetration rate over the entire length of the hole. Furthermore, the paper shows the effect of deviation on the blasting results through a prediction of fragmentation blasting model optimised with reduced deviation and highlights the effect of presplit mining and timing delay on the blasting effectiveness. Although the size pattern increases with deviation, a strategy pertaining to timing delay with blasting would be to align to the work of Grant (1990) where the optimum hole to hole delay is found to be between 7–10 ms/m of spacing, while the optimum delay between adjacent ring varied between 110–160 ms. Stabilisation of crowns and wings will perform with the implementation of presplit blasting.

Mar 29, 2023

By T Barto, D Thomson, T Norgate, C Doblin

Collaboration between CSIRO Minerals and SunSalt Pty Ltd, a salt producing company located in rural Victoria, has resulted in a commercial process to recover magnesium sulfate (commonly called Epsom salt) from the saline waters of the Murray Basin. The feed for this process is bittern; the liquor remaining after halite (common salt) has been harvested from the saline water by evaporation.SunSalt produces salt and bitterns from three locations, namely Hattah (Victoria), Mourquong (NSW) and Wakool (NSW). The small size and considerable distances between these operations makes it uneconomic to build a stationary processing plant to extract value-added products, in particular Epsom salt, from the bitterns of the three operations. This fact led SunSalt to build a containerised mobile plant that could be moved to each site to process the bitterns at the end of the salt harvesting period.Epsom salt is extracted from the bittern by further evaporation, refrigeration and recrystallisation. In this process the bittern is diluted with five per cent volume of fresh water to minimise precipitation of residual halite in the bittern. Cooling the diluted bittern to between -5 and -10¦C precipitates up to 70 per cent of the magnesium sulfate, which is recovered as 85 to 96 per cent purity Epsom salt by filtration. This product is marketed as an industrial grade Epsom salt. Higher purity (up to 99.9 per cent) Epsom salt (USP or BP grade refined product) is made from the industrial grade product (raw Epsom salt) by recrystallisation.The containerised mobile plant was commissioned in December 2002. The raw Epsom salt generated in the mobile plant is refined to a higher purity Epsom salt in a separate plant located in Mildura. The Mildura plant was commissioned in December 2003.The CSIRO-SunSalt collaboration has demonstrated that the saline waters can be processed into a useful resource, and in addition could create jobs and a new skill base in regional Australia. The production of Epsom salt locally in Australia, which is worth currently about $A600 per tonne, removes the need to import over 3000 tpa from overseas with a net positive impact of $A2 million on the balance of trade.

Jan 1, 2004

By M Davies, G Theletsane, A H. Gray

Recovery of gold from gold ores has been driven by the available technology and its configuration in the process plant flow sheet.Conventional practice in test work programs has the ore being ground fine (to 106 or 75 microns) to ensure liberation ahead of leaching or flotation. This paper identifies that, in many cases, gold and gold sulfide carriers will liberate and be recovered to a concentrate at much coarser sizes.There is an exponential increase in energy consumption relative to particle size reduction. This impact becomes extreme when comparing crushing a product to 1 mm against grinding to 75?microns.The resultant reduction in energy consumption when liberating and separating at 1 mm or coarser compared to grinding to 75 microns can be in the order of 15 kWh/t or 60 per cent of energy in the comminution circuit.Recovery of free gold and gold sulfide carriers by preconcentration (using continuous gravity devices such as the InLine Pressure Jig), combined with flotation of the fine gold and gold carriers, can result in significant power savings.There are multiple locations within the flow sheet that can be targeted using this process, including recovery in the cyclone underflow of existing plants, preconcentration ahead of the plant or complete greenfield, low-energy process plants designed from first principles based on data from a Gekko developed test work regime.We will describe the process of defining mineralogy in the laboratory and the decision-making process through to actual applications in the field.Several examples will be provided, including a South African Witwatersrand gold ore, several Australian gold ores and others, indicating the benefits of this process and where it has been brought to commercial reality.CITATION:Gray, A H, Davies, M and Theletsane, G, 2014. Coarse liberation and recovery of free gold and gold sulfide carriers for energy reduction in process plants, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 117–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By P Hodkiewicz

Recent structural interpretations based on historic stope shapes were used to develop a rapid and innovative method to domain and simulate structurally complex, high-grade gold veins at depth in the Edna May deposit. This involved ‘implicit’ modelling of drill hole data using Leapfrog software, which allows complex wireframe domains to be built and updated rapidly, compared to ‘explicit’ manual wireframing methods that are too subjective and time consuming. Conditional simulation was used for resource estimation, in order to simulate the highly variable gold grades associated with the veins. Similar modelling methods could be used to determine the mining potential of other historic gold deposits that are receiving renewed interest because of the high gold price.Gold at Edna May is hosted in the Edna May Gneiss, which is a WNW-striking tonalitic intrusion along a shear zone that dips approximately 45° towards the NNE. Gold occurs in multiple 0.5 - 5 m thick arcuate quartz veins that plunge steeply towards the west. Two phases of historic underground mining at Edna May (1911 to 1922 and 1935 to 1947) produced 360 000 ounces of gold at an average grade 19.5 g/t from seven ‘reefs’ to a depth of 240 m. This established Edna May as one of the highest grade gold mines in Western Australia at the time.Recent drilling by Catalpa Resources confirmed the potential for down-plunge continuity of high-grade veins. New structural interpretations, based on historic level maps and wireframe re-constructions of the arcuate stope shapes, were used as ‘structural trends’ in Leapfrog to model the mineralisation. The resulting wireframes capture the complex distribution of gold in the deposit and were used as domains for resource estimation.Conditional simulation using the Turning Bands method was used to simulate the expected variability of gold grades associated with this mineralisation style and the median of the 100 realisations was used to report an inferred resource. Results of this modelling method are being used to target vein extensions at depth, to consider different underground mining scenarios, and to assess the risks associated with developing and mining this high-grade and high-nugget gold deposit.

Aug 22, 2011

By M Schaffer, T Kewe, N Moffatt

Porgera mine is 95 per cent owned by Barrick Gold Corporation. It is located at an altitude of 2200–2700 m above sea level in the Enga province of Papua New Guinea and produces approximately 460 000 oz per annum with a proven and probable reserve of 6.2 Moz. The refractory ore is ground in a conventional semi-autogenous grinding and ball mill circuit. After the gravity gold is recovered, the slurry is floated, oxidised in the autoclaves and then leached. This paper will focus on the flotation circuit and the recent upgrade of the control system. The five interdependent flotation circuits were challenging for operations to control as they dealt with variable grade, throughput and circulating loads, as well as the physical limitations of the equipment. With the installation of 18 Portage Froth Characterization® (PFC) cameras, the plant’s operation has been converted from a level-control based strategy that was focused on individual cells to one that targets grade and recovery control across the entire circuit. Variability in feed and the corresponding launder issues were addressed with a unique site initiative of deflector plates to indicate filling level. Non-linear closed loop control was implemented directly in the DeltaV Distributed Control System (DCS) using Portage Advantage Regulatory Control (PARC) algorithms and optimised with AwaRE advanced controllers. The most noticeable benefits achieved with the upgrade include improved flotation gold recovery, consistent flotation sulfur grade and autoclave performance. Correspondingly, there was a significant drop in boiler diesel fuel usage and launder overflow conditions.CITATION:Kewe, T, Moffatt, N and Schaffer, M, 2014. Porgera flotation circuit upgrade and expert system installation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 345–356 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By J Harding, S Munro, R A. Bearman

Despite the importance of the primary crushing stage, performance optimisation is not well analysed with sufficient focus to give improvement opportunities. At the Newcrest owned Telfer operation, liner life plays an important part in scheduling planned maintenance. Major consideration is given to monitoring crusher performance, as the highly abrasive nature of the feed significantly impacts the liner wear life. A study was undertaken by the lead author which focused on establishing a strong baseline of accurate data pertaining to the performance of the crusher, in terms of, operating parameters, liner life and key machine design factors. As part of the study, mining feed materials were examined for a particular set of liners and this revealed that improved methods should be pursued. Due to the competitive nature of the mining industry, the business solution to complex problems with long shutdown cycles should be streamlined to incorporate a non-operational modelling approach that is significantly more efficient than traditional online trial and error methods. In order to dramatically reduce the time and business risks, it was decided to engage services to model and simulate the liner life by varying main operational and mechanical factors. The key to all simulation work is gathering high quality baseline data. Such data allowed deployment of the Kinematic Crusher Model and validation of the model against worn 2D wear liner profiles. The proven model was then successfully deployed to predict operational values that defined crusher performance. To enhance the study, further investigation into a set of mechanical and operational simulations generated a sensitivity matrix measuring key performance parameters throughout the wear life of the liners. The study revealed throughput as a highly sensitive parameter and a change in eccentric throw provided the greatest improvement in extending liner wear life.

Aug 24, 2022

By K G. Harding, A Osman, A du Toit, F K. Crundwell, C M. Sheridan

"Most mineral processing plants have high water requirements for their operational activities. These plants often function in an environment where water is becoming increasingly scarce. An increase in population will result in an increased demand for water; potentially beyond the limits of supply and hence increased competition for the resource. In South Africa, Gauteng and the North West Province are likely to be first to experience a shortage of potable water.In order to avoid a water crisis, efforts must be made to ensure the effective management of water resources and the minimisation of wastage. Hydrometallurgical plants have a responsibility to society and the environment to operate in a sustainable manner - reducing their water requirements will certainly assist towards developing a sustainable footprint.This project improved site water management by: surveying the potable water and storm water systems with a view to assessing the current water accountability and determining methods to improve accountability determining the monthly and yearly water balance for the site and presenting it in the form of a water balance sheet drawing up an input-output and operational model in accordance with the Minerals Council of AustraliaÆs æWater Accounting Framework for the Minerals IndustryÆ calculating the water footprints of the refinery identifying ways in which water savings could be achieved recommending management systems for water usage monitoring.This work was conducted in South Africa. The value of this work lies in that it established the current baseline and assisted in developing management systems that can reduce water usage sustainably.CITATION:Osman, A, Crundwell, F K, Harding, K G, Sheridan, C M and du Toit, A, 2013. Water accountability and efficiency at a base metals refinery, in Proceedings Water in Mining 2013, pp 277-286 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

To enable ammonium nitrate-fuel oil (AN-FO) to be used on an equal weight basis with nitroglycerine explosives, smaller diameter bore holes became necessary with consequent modifications to drill steel and burden on holes. Detonation of AN-FO in small diameter holes proved successful both with and without primer charges but some alterations were required to adapt anoloders to the smaller holes.Important factors in training all operators in the new charging method were the retention of improved fragmentation, avoidance of excessive overbreak and keeping wall rock dilution to an absolute minimum. The successful storage of ammonium nitrate in climatic conditions with daily temperature fluctuations above and below the critical 90°F has been achieved.INTRODUCTIONTechnical aspects of ammonium nitrate-fuel oil (AN-Fa) blasting agent are well covered in recent literature. This paper deals primarily with the manner of its introduction as the principal explosive underground at Great Boulder Gold Mines Ltd. and with the many problems encountered in the process. Following reasonably successful experimental firings in June 1962', using granular ammonium nitrate and an anoloder, permission was granted by theWestern Australian Mines Department to carry out test work in selected areas of the mine. The permit allowed for fuse firing only, and for a mixture of AN-Fa containing between 5t and 6 per cent fuel oil, with an adequate primer.The use of AN-Fa on an equal weight basis with nitroglycerine explosives, involved smaller diameter holes with alteration to ground burden and modification to drill steel.Initial tests indicated that it was apparent that AN-Fa could not replace gelignite on an equal weight basis if the...

Jan 1, 1965

To help meet the challenge of mine finding at the start of the 21st century, the exploration geophysicist will have at his command a powerful range of tools, some new, some improved, and some which already exist today but are as yet little used. Remote sensing, using satellite and aircraft-based multi-spectral scanners, will provide the means for routinely mapping the surface distribution of certain carbonate rocks, clay and ferrous alteration minerals, based on the analysis of solar reflectance spectra. Time and emission-spectral resolved laser-induced fluorescence will likewise map the distribution of certain ore and pathfinder minerals, as well as certain skarn zones, all potentially related to ore deposits. The GPS (Global Positioning System), based on 18 orbitting satellites, will provide a universal, three dimensional, all weather navigation system which will completely supplant all existing aerial navigation systems, and greatly facilitate aerial surveying and automated processing and presentation of the data. Aeromagnetic gradiometer measurements will provide higher geometric resolution which will yield better definition of individual geological units. Multi-method ground geophysical surveys will be greatly expedited through the use of portable microcomputer-based, multi-sensor instruments. These instruments will interface with other intelligent devices for automated processing, presentation and interpretation of the ground field data. Borehole geophysics will come into more general use, both for at-hole measurements, especially using active nuclear techniques for grade determination, and for remote detection using a variety of electrical, magnetic, seismic and other methods.

Jan 1, 1986

By K G. van den Boogaart, S Konsulke, R Tolosana Delgado

Adaptive mineral processing has to rely on spatially predicted information on primary geometallurgical parameters, like phase composition, size and shape distributions of grains from various phases, portions of value elements in different grain types. Naively, one would predict these parameters geostatistically and select an optimal processing for the predicted structure. This is suboptimal, due to various kinds of non-linearities in the problem. First, some primary geometallurgical quantities themselves are measured in non-real scales, like compositional or stereologically distorted geometric information. Standard geostatistics has to be replaced by compositional and geometric geostatistics, involving complex transforms and restrictions. Further, only partial and uncertain information is available, introducing a stochastic character to the optimisation problem. Moreover, many response variables leading to costs, outcomes and eventual effects of later processing depend non-linearly on the primary geometallurgical parameters, which implies that the final monetary value is not estimated unbiasedly by kriging. Finally unbiased linear prediction (such as kriging) is not the best method of prediction for decision making. The conditional expectation of the monetary values is needed instead. The impact of these problems is explained in this paper, with simplified examples, and a first approach to a general solution is proposed. CITATION:van den Boogaart, K G, Konsulke, S and Tolosana Delgado, R, 2013. Non-linear geostatistics for geometallurgical optimisation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 253-258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By V Glenn, P McKenna, H Vickers, P Audet, M J. Gillespie, A Gravina, D R. Mulligan

A requisite corollary of mineral sand mining on North Stradbroake Island (Queensland (Qld), Australia) has been the progressive rehabilitation of post-mined lands for the revegetation of native subtropical Eucalypt communities. Since 2005, rigorous environmental monitoring has been undertaken to verify the annual development of post-rehabilitated sites. From these long-term analyses, a chronosequence of land revegetation (ranging from three to 26 years postrehabilitation) was developed to examine the rehabilitation trajectories of various post-mined sites in relation to proximal undisturbed locations. Here, we identified that some sites may be deviating from the intended natural analogues as evidenced by the opportunistic colonisationand otherwise æinvasiveÆ behaviour of a regionally native species (Black Sheoak - Allocasuarina littoralis), which appear to be displacing the intended Eucalypt varieties. Although it is recognised that the broader data trends correspond to distinct periods of adaptive modifications to the implementation of rehabilitation (ie pre- and post-1995), this analysis focuses on further identifying potential above- and belowground feedback mechanisms underlying these divergent ecological outcomes.CITATION:Audet, P, Gravina, A, Glenn, V, McKenna, P, Vickers, H, Gillespie, M J and Mulligan, D R, 2012. Above/belowground feedback may facilitate and sustain mono-dominance on rehabilitated North Stradbroke Island, in Proceedings Life-of-Mine 2012 , pp 15-24 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By M F. Gazley

The amphibolite-facies metabasaltic rocks of the Mine Mafic Package at Plutonic Gold Mine, Marymia Inlier, Western Australia, contain an estimated total endowment of 12.2 Moz of Au, which includes 4.71 Moz of past production and 2.77 Moz of reserves and resources; the remainder comprises lower-grade inventory. Over 65?000 multi-element analyses of whole-rock core and face channel samples from the underground workings of the deposit have been collected by portable X-ray fluorescence (pXRF) using a handheld Innov-X Omega pXRF unit. The analyses were performed on pulverised samples through paper bags, and were corrected using a pulverised, matrix-matched, reference standard. This method of data correction compares favourably with conventional XRF analyses performed on the same samples.A preliminary study based on pXRF analyses from a small number of drill holes found that a geochemical stratigraphy was evident in the pXRF data, and that this stratigraphy strongly controlled the location of Au mineralisation. The present study incorporates a much larger pXRF data set that samples a greater volume of diamond drill core and face channel samples and presents the data in a three-dimensional (3D) framework.This data set allows an investigation of the mineralogy of Au mineralisation with varying geochemical associations across the deposit. Historically, there has been a strong relationship identified between As and Au, which has caused issues with metallurgical performance, rendering some areas of the deposit only marginally economic. Utilising seamless data integration of the pXRF data set allows for recognition of the different styles of Au mineralisation using elemental concentrations and ratios from the multi-element analyses (Au:As, Au:As:Cu, As:Cu vs. K:V), and to visualise the distribution of these different mineralogical associations in 3D. The results of the 3D modelling and geochemical characterisation of the different styles of Au mineralisation are currently the focus of an extensive metallurgical testing program, the preliminary results of which are presented here.

Aug 22, 2011

Before I begin this paper, I thought that it would be important to start with a brief background on myself. This will give some insight into where I am coming from with some of the ideas presented in the body of the paper. I studied mining engineering at the University of New South Wales, graduating with Honours in 1999. When I finished university I was offered a job with PricewaterhouseCoopers in Sydney, working in the Energy and Mining Group of the Audit practice; which I accepted. I have been working at PricewaterhouseCoopers now since January 1999, completing an accounting conversion course at the University of Technology Sydney along the way. I am currently beginning my Professional Year for Chartered Accountant qualification. During my later years at university, continuing on through the start of my working career, I have been involved with the Sydney Branch of The AusIMM; firstly, as a student representative and, now, as the Young Professional Representative. Therefore, you can probably see that I will have very different young professional experiences than some of my peers who have been working on mining sites. The purpose of this paper is to examine the challenges that face graduates who are entering the industry and what solutions are used to ensure that this entrance is as smooth as possible. A challenge has then been made to the industry and The Institute in the form of further observations on ways that this entrance may be improved and the development of graduates to be more effective. In preparing this paper I have discussed various graduate experiences with some of my colleagues in order to see what some of the challenges they, themselves, face now and, also, going forward. I also discussed with them what they see as solutions to these challenges, drawing on some of my own experiences in a different company environment.

Jan 1, 2000

The invitation to speak today was in the form of a single sentence instruction: How does your company run and how do you communicate from top to bottom? It looks like I'll have to let you into our little secret. The team at Croesus know what works for us but we've never talked about it with others - least of all presented it at a conference such as this. In fact we tend to avoid the jargon normally associated with Best Practice or TQM, however in our own way, each of our staff are 100 per cent loyal to our company's aim to maintain and strengthen our commercial success. Just how we achieve this at Croesus is the subject of this presentation today, but first a little history. My dear old grandfather arrived in Kalgoorlie, as a mining engineer 100 years ago. Do you think he would have chuckled if someone suggested to him that a hundred years later we would just be starting to understand Kalgoorlie's geological mysteries? Well, here we are 100 years later and Croesus Mining is fortunate to be part of a generation now realising the true potential of Kalgoorlie's Goldfields. This provides us with a very fertile field in which to sow the seeds we can obtain from the World's Best Practice in Mining and Processing. With each new mineral deposit being discovered, old theories are being exploded. Each new deposit has a personality of its own, leading to some belated pioneering theories of where to drill next, and how to reduce internal costs so that we can win the war against constantly increasing external costs. What we have now and what the old timers didn't have is a huge database of geological input spanning several gold booms and a couple of nickel booms. My only interest in history is to pick up the points that may help us for our future. This is what we are doing in our company which is something of a David, in the David to Goliath range of mining companies in Australia. As a humbling thought; of the 115 164 tonnes of gold that the world's mines have produced throughout history, four tonnes have been produced by Croesus Mining. That's equivalent to 0.003 per cent of the total world's gold production. In the past financial year we achieved a dividend yield of five per cent. To put this into perspective, that's over twice the dividend yield of BHP, Australia's largest company. As we are somewhat less known than BHP, let me spend a few moments giving some particulars of our company's background.

Jan 1, 1995

By K Smith

This paper presents an assessment of the Robertson (2010a) method within the CPTu inversion parameter framework of Been et al. (1987), using CPTu calibration chamber data presented by Jefferies and Been (2015) and in other literature to assess the validity of the method, with particular focus on applicability of the method to TSFs (i.e. its applicability to loose silts and silty sands). The assessment demonstrates that although the method estimates values of k consistent with calibration chamber data, the method estimates values of m that are generally 1.5 to 2 times greater than calibration chamber data. As a result of this, the method generally overestimates Ψ for values of Ψ less than 0, and underestimates Ψ for values of Ψ greater than 0. This may result in both overly conservative assessment of materials as potentially liquefiable and unconservative predictions of material behaviour for loose materials.

Jul 1, 2021

By S Girard, L Rowland, V Lawson, Y Shields

Since 1948, ValeÆs Matte Separation Plant has been successfully using magnetic separation and froth flotation to separate the copper sulfide, nickel sulfide and Ni-Cu metallic alloy contained in Bessemer matte for downstream processing. Though some equipment upgrades have been performed over the years, the flow sheet has generally remained unchanged since the early 1970s. The need to improve metallurgical performance led to the trial of a scalping flotation column to produce a final copper concentrate ahead of the cleaner circuit feed to take advantage of a high degree of copper mineral liberation, reduce cleaner-recleaner circulating loads and decrease the associated loss of selectivity. Plant results indicated that 50 per cent of copper contained in the rougher concentrate could be recovered at final grade target. Results indicate that up to a 1.5 per cent increase in copper recovery to copper concentrate was achieved during the scalper trial due to a reduction in the generation of fine chalcocite which has historically been observed to report to flotation tailings due to surface contamination. Deficiencies are currently being addressed and a long-term trial is scheduled to confirm the benefits of copper scalping.CITATION:Girard, S, Rowland, L, Shields, Y and Lawson, V, 2012. Copper scalping at ValeÆs matte separation plant, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 299-308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Szwedzicki T

Uniaxial testing was performed on model pillars to determine the effect of width to height ratio on pillar and surrounding rock mass stability. Samples were modelled in a shape similar to that of dumbbell weights, with the centre representing

Jan 1, 1994

By E Niva

The IsaMillÖ is challenging the way that plants are designed and operated. This paper challenges existing designs of concentrator flow sheets, particularly focusing on magnetite circuits.   From what has started out as a small scale ultra fine grinding mill in the pharmaceutical and pigment industries, it has been redesigned and improved upon for mineral processing, and has been the mainstay of fine grinding applications for over ten years. These applications have required energy efficient grinding to succeed, and have been predominately in the base metals industry.   Further development of the IsaMillÖ has now resulted in the machines being able to treat larger tonnages, with higher capacity motors. This development, along with the introduction of purpose designed ceramic media, has allowed the mill to treat courser feed sizes. At the same time, the mill still offers highly efficient grinding, and has enabled it to be operated in coarser tertiary and secondary grinding applications.   The acceptance of the mill in coarser applications, predominately in base metals and PGM applications, has enabled the IsaMillÖ to be a serious contender for beneficiation in other minerals. One such application is the potential for IsaMillsÖ to be part of magnetite flow sheets, which are being considered in Australia to meet the growing iron demand of China. The high energy efficiency of the IsaMillÖ compared to conventional technologies, as well as the smaller infrastructure requirements, provides a great opportunity to reduce the power intensity of magnetite circuits.   This paper will examine the use of IsaMillÖ technology in conventional grinding applications, including recent testwork in a primary grinding base metal circuit, as well as testwork on magnetite ore comparing a lab scale IsaMillÖ with a lab scale Tower Mill.   The growing demand for minerals over the next decade, coupled with higher energy cost, will result in energy efficient technology, such as the IsaMillÖ, being included in standard circuit design.

Jan 1, 2008

GENTLEMEN, I have to thank you very much for the honour you have conferred upon me by electing me President of the Institute for this year. On behalf of resident members, I have to offer the visitors a very cordial welcome to Mount Morgan, and to tell them that all arrangements have been made to enable them to inspect the mine and works at their own convenience, and to supply them with any particulars they may need.It is very pleasing indeed to see such a large gathering, especially on account of the long journeys many have undertaken in order to be present. The first congress in Queensland, about eleven years ago, was attended by a comparatively small number of members, and a rather long time has been allowed to pass in consequence. The large attendance at this meeting encourages the holding of meetings in Queensland more frequently. Owing to the long distances, and the number of mining centres in Australia and New Zealand, we cannot expect to meet oftener than once in six or seven years in...

Jan 1, 1911

The continuous casting of zinc alloys has been of fundamental importance for many years in the production of a number of products, including sheet for architectural applications, battery cans for dry cells and wire for metallising. The intrinsic benefits of continuous casting, including efficiency and high tonnage capability, uniformity of metallurgical structure and properties, and absence of voids and other defects, have contributed to the success of these products. Less well known, but of growing importance, is the more recent application of continuous casting technology to the production of zinc alloy bar stock products, including bearing stock, machining bar stock, forging stock and cathodic protection anodes. A wide range of zinc alloys are now continuously cast in a variety of cross sectional shapes and sizes to suit the diverse characteristics of these products. Of particular significance are the introduction of hollow zinc-aluminum bearing stock, and the availability of zinc alloy machining bar stock for hydraulic applications and for producing prototypes of zinc alloy pressure die castings. In addition to the traditional benefits, continuous casting provides special properties which are important in the application of these bar stock products. The list of successful applications of continuously cast zinc alloy bar stock is growing rapidly, and the market potential for resultant new zinc applications appears to be significant.

Jan 1, 1993