Search Documents

By L Mollison, K W. Mills, N R. P Baczynski, M F. Lee, I A. de Bruyn

This is the first of two papers concerned with rock stress inputs to various mine design issues at the large Ok Tedi open pit mine in Papua New Guinea. The companion paper (also published at this conference) is ‘The Application of Rock Stress Inputs to Stability Assessments at Ok Tedi Mine, Papua New Guinea’ (de Bruyn et al, 2014).Stresses are a required input for numerical modelling of mine design issues. However, for some operations, like the very large Ok Tedi open pit mine in remote rugged mountainous terrain, direct and representative measurement of rock stresses can be technically difficult and expensive. In such situations, development of an appropriate and sufficient understanding of rock stresses can be challenging.This was addressed for Ok Tedi by considering the following:The tectonic and regional geologic setting of the mine.Results from three different programs of rock stress measurement over 19 years, including hydraulic fracturing (1991), acoustic emission (2007) and overcoring (2010). Some interesting results of the overcoring work are discussed. It was done in a 4 km long drainage tunnel, which intersected a thick monzodiorite intrusive that has metamorphosed contacts to host contact Ieru Formation siltstones; anomalously low horizontal stresses were measured within the monzodiorite.Compilation of rock stress measurements from other New Guinea mines and prospects, both in Papua New Guinea and Indonesian West Papua.Comparisons between the variable Ok Tedi rock stresses and similar data from other porphyry copper deposits.CITATION:Lee, M F, Baczynski, N R P, Mills, K W, de Bruyn, I A and Mollison, L, 2014. Rock stresses at Ok Tedi, Papua New Guinea, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By R C. A Minnitt

The Witwatersrand Supergroup is host to the world’s largest gold deposits. The location, quantity, grade, continuity and other geological characteristics of a Mineral Resource are either known, estimated from specific geological evidence and knowledge, or interpreted from a well constrained and portrayed geological model. Establishing such a model is an integral part of the evaluation process in the Anglogold Ashanti (AGA) group, and is referred to as a Geoscience Business Model for the mining operations. The geological model established over the years has relied on detailed descriptions of the mineralisation, and understanding of the regional and local geology of the Witwatersrand sediments, in the West Wits and Free State goldfields. The processes of data collection in regard to underground stope and developing mapping, structural and sedimentological mapping, and the geological inputs to mine planning systems are described, together with aspects of drilling, sampling, grade control, and data management. Anglogold Ashanti’s Geoscience Department employs a complex and unique process to generate the Mineral Resource, including a 3D geological structure model of the orebodies which are usually highly faulted, and a robust mineralisation/facies model on which the decisions about domain boundaries are established. A Mineral Resource Inventory System (MRIS) has a dynamic graphic interface to the resource database that is used for compiling the resource statement. It is also used to determine the gold-called-for, as well as short and long-term planning. A unique estimation process using the extensive closely spaced stope face sampling database and the more widely spaced surface drilling information is used in combination in the Macro Co-Kriging estimation. The use of different support sizes in the C0-Kriging process is preceded by the equally unique ‘clusterisation’ and ‘acceptorisation’ procedures by which the data are quality controlled and assured prior to their use in the kriging process. The Mineral Resource and Ore Reserve estimates are classified according to the SAMREC code through a method that ensures that they are compliant, auditable, transparent and reconcilable with previous Mineral Resource and Ore Reserve statements.

Aug 22, 2011

By J Y. C Lo

The construction of two drainage tunnels and the associated subvertical drain system at the Po Shan area in Hong Kong was completed in December 2009. This project is the first of its kind to utilise drainage tunnels and a network of subvertical drains to regulate the groundwater table to enhance the long-term stability of the hillside of Po Shan area.The groundwater levels, monitored by preinstalled piezometers, once exhibited dramatic drops during drilling of the subvertical drains; however, have recovered from natural replenishment after effectively plugging of the drains. The level of groundwater drawdown is in line with the design function of the subvertical drains. In order to understand the groundwater flow pattern in the Po Shan area during and after construction and to set out operation schemes for the subvertical drain system so as to control the groundwater table in the Po Shan area, a post-construction review has been carried out to examine the behaviour of the drainage system and its impact on the surrounding subsurface groundwater flow.This paper presents a review of the groundwater monitoring data during and after the construction of the drainage tunnel system covering a period of over 3.5 years. A simplified conceptual hydrological model is developed, which has been verified by the monitoring data, to capture the key elements with regard to groundwater variations in different stages of the construction. The performance of the tunnel and subvertical drain system as revealed from these field measurements is discussed.

Mar 8, 2011

By D Tucker, K Harney

Hatch forecasts that an increasing share of seaborne traded iron ore will be ultrafine, being either concentrate or pellet feed. This provides several challenges for the iron and steel industries, but the principal concern is: how much ultrafine iron ore can be consumed on sinter strands and with a minimal effect on productivity?This paper will identify new supply by project through 2020. Demand will be estimated for sinter production and practical steps will be identified to increase ultrafine consumption in sinter strands. The long-term iron ore price will be forecast to balance supply and demand. The paper will conclude by assessing how the pricing of ultrafine ore will develop relative to the Chinese iron ore indices.CITATION:Tucker, D and Harney, K, 2015. Iron ore ultrafines challenges and opportunities, in Proceedings Iron Ore 2015, pp 501–504 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By M G. Aylmore, L W. de Klerk

Roasting of refractory gold ores has been a commercial process for many years. Improvements in design of fluidised bed roasting technologies and low capital and operating costs compared with other refractory treatment processes can potentially make roasting a viable option.However, gold extraction from roasted ores carried out on laboratory scale equipment often invariably yields lower recoveries than other processes such as bio-oxidation or pressure oxidation. Non-optimal laboratory roasting conditions can incorrectly write roasting off as a process option.Low gold recoveries from the cyanidation of calcine products from roasting can often be attributed to roasting conditions not favouring gold liberation and agglomeration processes, particularly if lockups of elements such as arsenic are being pursued for environmental reasons.This paper reviews the conditions favoured for gold agglomeration and accessibility of gold to cyanide, test conditions to achieve gold liberation and agglomeration on laboratory scale and designs that incorporate staged decomposition and roasting to make roasting a more commercial option.CITATION:Aylmore, M G and de Klerk, L W, 2013. Conditions and design considerations for maximising recoverable gold in roasting of refractory gold ores, in Proceedings World Gold 2013 , pp 375-388 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

Since I first enrolled to study Mining Engineering, the idea of working with big machinery and explosives has always appealed to me. After a few courses at uni, combined with vacation work and a number of presentations at the New LeadersÆ Conferences I had attended, I began to realise that the explosives side seemed to have more appeal than the others. As I look back on the past two and a half years that I have spent with Orica Australia Pty Ltd as part of their graduate program, I would have never imagined the dynamics of explosives in mining. This I put down to the ever changing and rapid development in technology converting blasting techniques into a defined predictable science. The opportunities I have been given have delivered all the appeals from when I first started my study. As a result of my entry into a profession that uses explosives to deliver broken rock in a range of mining and construction projects, through the use of advanced blasting technology and products, my experiences have been wide and varied. These experiences have included the use of OricaÆs i-konÖ detonator technology and blast design software to allow for blasting operations to occur in a range of environmentally sensitive quarrying and construction projects throughout New Zealand, to the implementation of various Orica blast based services aimed at improving dragline dig performance and reducing coal loss thus improve overall mine sustainability in the coal mines of Central Queensland, to the advanced utilisation of Orica explosive products and technology in a number of the worlds largest copper mines in Chile. I have witnessed first hand the blasting technology available within Orica Mining Services to both deliver fundamental changes in mining results and in turn kick off my career with a bang.

Jan 1, 2009

By S Williams, N McBride

The aim of these analyses was to utilise the latest available production information for the Wandoo operation to determine the optimal blasting parameters, costing information and predicted results (fragmentation, muckpile shape and vibration). Much of the data used as input was made available from the information gathered during the excavation of the test pits during 1995. As with any æplanning stageÆ analyses, many assumptions were required to fill gaps in the available data. The calibration of computer blasting models was conducted using data from the last of the test pit blasts (this blast was carried out in material that closely resembled rock expected to constitute the bulk of the base case design pit). This calibration was refined using observation and experience based judgements to extend the accuracy of the predictions as far as possible. All the simulations were performed assuming that the blastholes will be wet (as instructed by BGM). This has consequently determined that the appropriate explosive for the simulations and the actual blasting will be a pumped emulsion/ANFO blend. The following blast design parameters were derived by determining a likely range of powder factor (from other similar scale gold mines) with a median value of 0.62 kg/m 3 being the powder factor arrived at through the field optimisation process conducted during the test pit excavation. The total swell/displacement percentage (volume after blast/volume before blast) largely determines the diggability of a well fragmented muckpile. Consequently where fragmentation is good any reduction of total swell will probably reduce diggabilty. Any reduction of diggability can and should be traded off against increased gold recovery. In most gold mines, diggabilty will be substantially compromised at the balance which produces the most profit. When these considerations are combined with the cost to drill and blast material, processing costs and the achievement of æacceptableÆ diggibility, the analysis becomes extremely complex and qualitative. Many trends are evident including:the relationship between powder factor (for each blast design) and maximum forward displacement (throw), see Figure 1; and the relationship between powder factor (for each blast design) and drill and blast cost per BCM, see Figure 2. The following blast designs are matched to each of three ore-tonnage alternatives (as supplied by BGM) (Table 1). They are all based on powder factor of 0.62 kg/BCM and are considered optimum from a mining æpoint of viewÆ. The costing of each design includes drilling, explosives and labour cost to load, stem and tie-in holes. Using the available rock data and relying heavily on the wall exposures in the test pit(s), it is the opinion of the author that between 20 per cent to 40 per cent of the final walls excavated in the Wandoo pit would be likely to have the angle between the dominant foliation and the wall plane that is well suited to presplitting and be cost-effectively served by presplit technique. The drilling cost for 125 mm blasthole is about $11.40 per drilled metre and the cost of 40 mm presplit explosive is about $140 per 25 kg (17 metre) case. This implies that the cost to drill and blast presplit on the above parameters would be about $10.90 per square metre of presplit face. The remaining wall area would be most cost-effectively delineated using modified production blasting techniques. This requires the use of modified parameters such as smaller hole diameters, smaller spacing/ burden, higher powder factor, free face firing, less rows per blast and longer delays. These altered blast parameters would usually be applied uniformly across the entire blast fired adjacent to the wall and this ætrimÆ blast would relieve burden away from the wall, into the pit. In simplest terms, this method relies upon maximised burden relief to minimise blast energy applied to the wall. It is only applicable where the material to be blasted is waste since the throw achieved is inconsistent with ore dilution control. The largest charge weight per hole for these analyses is 360 kg and the nearest domestic structure to the proposed Wandoo pit is about 6100 metres distant. From these parameters and assuming a worst case example of rock controlled site factor, the predicted ground vibration is 0.5 mm/sec that is about five per cent of the lower limit set down in AS 2187 part two (1993). This suggests that for the current location of neighbours, ground vibration will not be an issue for the Wandoo operation.

Jan 1, 1999

By M S. Reston

The Tonkolili banded iron formations (BIF), Sierra Leone, host extensive iron ore deposits which are of economic signifi cance to the seaborne iron ore trade. The deposits are dominated by a strategic JORC compliant mineral resource of 11.6 Bt grading 30.1 per cent Fe comprised of primary magnetite mineralisation in the form of a fresh metamorphosed BIF featuring a uniform mineral assemblage of quartz-magnetite ± ferro-silicate minerals. Pilot plant metallurgical test work has demonstrated that the production of a magnetite concentrate is achievable using the established beneficiation techniques of magnetic separation and flotation. The concentrates arehigh-grade, and suitable for blast furnace or direct reduced iron pellet feed. The major challenge facing the development of such magnetite deposits at industry competitive production rates is the significant capital investment required for process plant and associated infrastructure.Two well-developed weathering zones exist within the deposits, and are associated with the progressive development of a tropical weathering profile overprinting the primary BIF. These zones feature a near surface hard indurated duricrust up to 60 m thick, and a soft progressively developed saprolite between duricrust and fresh BIF. These zones have been found to be amenable to producing iron ore products including DSO lump and sinter fines from the duricrust, and concentrate from the saprolite. Mineral resources sufficient to support commercial production of such iron ore products were defined by an intensive exploration program in 2010.African Minerals Limited has developed a three phase production strategy to progressively self fund the development of the Tonkolili strategic magnetite project by:• commencing a Phase I 12 Mt/a DSO operation in Quarter 4 2011,• increasing production in Phase II to 35 Mt/a with the commissioning of a saprolite beneficitation plant and associated infrastructure upgrades, and• developing a 45 Mt/a Phase III operation producing high-grade magnetite concentrate.The comparatively low capital and operating costs of a duricrust DSO lump and sinter fines operation coupled with its proximity to ground surface make it highly attractive for the generation of early cash flow for the Tonkolili project. Revenue from this early production may be used to selffund the subsequent development of phases requiring progressively more significant beneficiation plant and infrastructure.

Jul 11, 2011

This paper examines the impact of the time value of money on the location of mining facilities, as examplified by a central processing plant serving several mines. Three approaches, the Euclidean-Distance Approach, the Gravity Centre Approach, and the Rectilinear-Distance Approach, commonly applied to a single facility location problem were employed in the study. The objective function in all three models was the updated value of the following three costs influenced by the processing plant location and defined within the framework of the continuous model of value representation and the continuous interest rate convention: I. the costs of transporting the useful mineral from the mines to the plant, 2. the costs of constructing the transportation links between the mines and the plant, and 3. the costs of maintaining these links over time. Results of the study show a substantial impact of the time value of money on both the processing plant optimal location and the opportunity cost of neglecting the time value of money in the locational considerations.

Jan 1, 1995

By L Lorenzen

The selection of samples for metallurgical test work is generally focused on providing geologically representative samples. One of the major problems experienced with metallurgical test work using drill hole data, is the small sample sets selected for metallurgical testing. Major process and financial decisions are being made from results obtained using snapshot samples. Snapshot samples means that samples are basically selected only by grade and spatial location with the assumption that the rest of the orebody or portion of orebody is similar and will respond metallurgically the same way – ie the assumption is that the mineralogy and lithology are basically the same as the test sample. From the test work, algorithms were usually developed and used to describe throughput and recovery using some explanatory variables including grade (mineral chemistry) and ore hardness. These algorithms were then used in the recovery models to determine tonnes produced and plant throughput. However, the metallurgical parameters are a function of many geological factors including grade, lithology, alteration, mineralogy, spatial relationships and SG. In previous years, the limited mineralogical information available was deemed enough for the metallurgist to make decisions as to how many samples are needed to evaluate the metallurgical performance of the ore during processing, and subsequently the basis for the plant design. If the orebody is consistent and not complex or refractory (thus, relative simple lithology), then only spatial and grade samples will be needed to evaluate the throughput and recovery, so limited mineralogical information may be acceptable. There is now, however, an increasing realisation that the mineralogy and geology change, as do the metallurgical characteristics of the orebody, so limited samples may not be sufficient for effective metallurgical test work.It is the purpose of this paper to discuss the effect correct mineralogical information has on the subsequent metallurgical test work program and process selection using a case study. Factors such as type of rock, rainfall and topography are thought to influence the minerals that ultimately form in various orebodies, with the result that different orebodies often react differently during metallurgical test work programs. It is therefore important to obtain accurate mineralogical and elemental deportment data, which will also indicate where the valuable metal containing minerals are located within the orebody. The better you plan and execute your metallurgical test work program during the early phases, the more accurate the decision-making process will be during the selection phase. Improved integration between geology and metallurgy data gathering (geometallurgy) during early phases will result in more accurate predictions with regard to throughput and recovery during modelling and process. Equipment selection will be considerably simpler in later phases with early planning, with improved mine and process scheduling and subsequent net present value (NPV).

Sep 5, 2011

This paper describes a detailed geostatistical study of producing copper orebodies at Mount Isa Mines Limited in Queensland, Australia. As a result of this work, kriging has been adopted for grade estimation for final stope design at Isa Mine. Extensive variogram and back analysis studies indicate that one relative variogram model can be used to give optimal kriged grade estimates from production sampling throughout the 100 million tonne copper orebody complex. The kriging method replaces a computer technique used at [sa Mine based on inverse distance weighting using parameters chosen from experience.Comparative stope designs based on 10 million tonnes of ore indicate a 16% increase in minable ore tonnage at a grade well above the cut-off, as a result of the geostatistical work.Although this paper is written as a practical description with simple explanations of geostatistical concepts, the theory and use of relative variograms has been expanded. A possible link is suggested between relative variograms and first order kinetics of natural mineral concentration processes.

Jan 1, 1982

By S Morgan, L C Pagdalian, S Serdzeff, C Malaloy-on

It is widely accepted that mineral deposits are decreasing in metal grades. To remain profitable and meet market demand, mining companies are expanding their operations by increasing the tonnage treated. These expansions may include new concentrators with higher nameplate tonnages or upgrading the capacity of existing ‘brownfield’ operations. In many cases, the brownfield upgrade route is preferred as it is less capital intensive; however, brownfield upgrades are never straightforward and present many metallurgical and engineering challenges.For example, to increase feed throughput at a brownfield site, there will be a requirement to modify the mine development plan. This may result in the ore mineralogy varying beyond the current feed fluctuation range. To accommodate these ore variations, a combination of mineralogical analysis and small scale testwork can be used to develop a new process flow sheet to achieve the product recovery/concentrate grade requirements. In general, however, flow sheet development does not usually consider site specific layout constraints and equipment requirements. At sites where future expansions were never considered, taking this silo approach could lead to project delays and compromise the circuit design.Engaging an experienced technology partner ensures the nominated project team is involved throughout all stages and aspects of a given brownfield upgrade – from conceptual flow sheet development, through to detailed engineering, construction and commissioning. The recent Carmen Copper Corporation (Carmen Copper) circuit upgrade has been completed in technology partnership with Outotec. The circuit upgrade was extensive and included new equipment additions to the comminution, flotation and dewatering circuits. Carmen Copper’s intimate knowledge of the ore characteristics, in conjunction with a trusted, knowledgeable technology partner, facilitated a robust circuit design, and fast-tracked the project execution. This paper deals specifically with the flotation circuit upgrade and highlights the benefits to Carmen Copper of this holistic approach.CITATION:Morgan, S, Serdzeff, S, Malaloy-on, C and Pagdalian, L C, 2014. The benefits of technology partnerships during brownfield upgrades, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 471–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

Establishing the link between the solid, cold rock of dikes, sills, plutons, and lavas and hot, active magma chambers is the quest of igneous petrology. Differentiation of Earth, the diversity of the igneous rocks, and the spectacle of volcanism are ample evidence that magmatic processes are fundamental to our understanding of planet formation and evolution. Single gabbroic plutons, on the other hand, often show intricate and abundant evidence of the effects of crystal growth and sorting. It has not proven simple, however, to establish the basic principles of magmatic behavior leading to this crucial evidence. Because of their abundance, exposure, simple geometry, large range in size, and often straight-forward petrology, sills are excellent examples of the magma chambers. Physical and chemical processes operating in sills can be recognized that also routinely operate in many other bodies. Understanding the dynamics of sill solidification is essential to understanding the genetic links between lavas and plutons.

Jan 1, 1990

By P Jones

Fosterville Gold Mine is an underground operation located approximately 20 km northeast of Bendigo and 170 km north of Melbourne. Fosterville is the most productive gold mine in Victoria, producing over 100 000 ounces of gold annually. Access to the underground is via two portals cut into previously mined open pits. Fosterville is 100 per cent owned and operated by Northgate Minerals, a gold and copper producer with mining operations, development projects and exploration properties in Canada and Australia. (Northgate Minerals Corporation, 2010).Underground operations commenced in 2006 with ore production focused on three orebodies – Phoenix, Ellesmere and Falcon. Primary ventilation to the existing operation is provided by wall mounted exhaust fans located underground. This system provides approximately 220 m3/s of primary ventilation to the operations with intake achieved through the portals. Exploration drilling during recent times has uncovered another lode, the Harrier orebody, located 2.2 km to the south of the existing workings. Due to the location of the new Harrier orebody, vent analysis revealed the requirement for a separate source of primary ventilation to service Harrier. Figure 1 shows a current underground long section and the location of Harrier in relation to the existing workings. A number of options were considered, including a parallel decline from one of the existing two portals, however, a 4 m diameter, 350 m deep surface ventilation shaft was selected as the most suitable and feasible option for the mine.In December 2009, geotechnical drilling commenced to determine the most suitable location for the shaft. Site locations were constrained by a number of factors including interaction with current and planned surface infrastructure as well as proximity to nearby community members at the southern end of the mining lease. Results from the geotechnical drilling indicated that the majority of the proposed shaft would be suitable for a 4 m raise bored shaft. However, the top 40 m of the proposed shaft were deemed unsuitable for raiseboring due to zones of weakness that would likely influence the stability of a 4 m diameter shaft (Robinson, 2010). Following independent geotechnical advice and input from experienced raiseboring contractors, it was decided to construct a 40 m presink prior to raiseboring activities.A crane mounted auger was chosen as the preferred method to construct the presink. This method differs substantially from traditional blind sinking methods which are highly labour intensive. The auger, or drill, is designed and built to be attached to a crane base using engineered pivoting cradles. The auger is suspended from the crane jib by pennant ropes attached to hydraulic rams. The auger applies rotation and axial loads to the drilling tools via a telescopic steel bar (Kelly Bar). Drill tools are attached to the bottom of the Kelly Bar and comprise an assortment of drilling buckets and reaming barrels. Drilling buckets cut in situ material and collect the spoil for removal and are used for the excavation of the ‘pilot hole’. Reaming barrels are used to expand the diameter of the excavation by directing cuttings into the pilot hole which are then removed by the drilling bucket. In June 2010, the presink was constructed utilising a crane mounted auger with support to the shaft walls applied via a remote fibrecrete unit. The excavation method involved cutting a series of smaller diameter holes (2.4 m wide) before reaming out to the final diameter (4.7 m wide) in 4 - 5 m vertical increments. Fibrecreting activities were carried out on the backshifts, to ensure the stability of the excavation and minimise interaction between the two units. The presink was completed on time and offered many advantages compared to traditional blind sinking methods, including safety, costs and timing. This paper will examine the benefits of this method as well as lessons learnt and future applications in the mining industry.

Mar 21, 2011

By W T. C Kendall, H D. Ngo

Garden Well is a shear-hosted Archaean orogenic gold deposit located 100 km north of Laverton, Western Australia. The Garden Well processing plant is designed for a nominal 491 t/h milling rate and annual capacity of 4 Mt. The plant has three key innovations:1. a scrubbing circuit, expected to reduce grinding power consumption by up to 20 per cent2. a secondary cycloning/gravity circuit, providing a second opportunity for gravity gold recovery (additionally, the circuit effectively increases the leach residence time of the coarse gold bearing fraction of the leach feed by approximately 60 per cent, without any additional tankage)3. the use of mid-stream oxygenation to enhance gold recovery.The Garden Well deposit is free-milling with overall laboratory gravity/leach gold recoveries exceeding 95 per cent at a P80 grind size of 150 ¦m. Three mineralogical domains have been identified: oxide, transition and fresh, with the fresh domain having subdomains of fresh ultramafic and fresh shale. There is a high component of gravity recoverable gold in all three domains.This paper will discuss these innovations and the design challenges and the risk mitigation strategies that were adopted to ameliorate the prototyping risk. The performance of the plant since commissioning together with lessons for the future will also be presented.CITATION:Smith, R J, Kendall, W T C and Ngo, H D, 2013. Treatment plant innovation at Garden Well, in Proceedings World Gold 2013 , pp 315-324 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Koppe J. C

This paper describes the methodology developed to establish a sequentia mining plan applied to a coal mine, using computers. Firstly, isocontou. maps were generated from the drill holes and outcrop description information, representing the thickness and depth of the rock formation: present in the mine site. The procedure relies on the repeated application of the cross validation techniques, until the standard deviation of thi estimation is reduced to a minimum.From this map the coal reserves of the two coal seams, the overburdet (separated in hard and soft material) and the interburden were calculated After that, the maps were transferred in digital files to AutoCAI software, where different mining plan simulations were performed. 7b ore evaluation in each case was done automatically, including tonnages volumes and stripping relations. The final mine configuration consider the economic aspects of the operation.

Jan 1, 1993

By Rokot M

In a little over three years, Chevron Niugini has built up a team of relatively young, hard working men and women, mostly Papua New Guineans, who spend most of their working days out among people in the Southern Highlands and Gulf Provinces who are directly affected by the Kutubu Petroleum Development Project. These are Land and Community Relations officers, or LACROs. They take on a huge responsibility, not only representing Chevron but also being friend, advisor and negotiator, frequently dispensers of medicines, and agricultural advice and more. When things go well, others get the praise, when things go wrong, LACROs are the martyrs. Just as the geologists who locate the oil, the drillers who find it, the engineers who design the facilities, the construction gangs who build them, the landowners who claim it, and the Government who monitor it, so are the LACROs part of a team.

Jan 1, 1991

By M Pernechele, U König

Most of the operating steelmaking capacity currently relies on conventional, coal-based steelmaking processes. Currently, direct reduced iron (DRI) is only produced in regions where energy is available at low cost. To align with net-zero emissions goals, steelmaking capacity must transition to loweremissions steelmaking technology. Direct reduction of iron ore will get one of the preferred methods in the future due to its high technology readiness. New reduction technologies include hydrogenbased direct reduction processes. To ensure optimal efficiency during DRI production and to cope with newly developed technologies, processes need to be monitored more frequently and accurate. Traditionally quality control of raw materials and DRI has relied on time consuming physical testing, wet chemistry or the analysis of the elemental composition. The mineralogy of DRI that defines its properties is not frequently monitored. Process monitoring and quality control of DRI is possible by using modern X-ray diffraction (XRD) methods. In addition to the metallic iron content (Femet), metallisation (Metn) and the total carbon content (Ctot), XRD analysis also identifies the overall mineralogical phase composition. This allows additional information about the reduction process and enables fast counteractions on changing raw material mixtures. The benefits of the quantitative determination of the phase composition and the calculation of process critical parameters to produce DRI will be demonstrated with a case study

Sep 18, 2023

My paper presents a discussion of the legislative and departmental requirements in connection with the acquisition of exploration rights for minerals (other than petroleum and coal) in the Independant State of Papua New Guinea, the Solomon Islands and Queensland and he practical problems associated with land entry and land ownership associated therewith. In general there are many similarities in the methodology and philosophy behind the legislation in each country and the contractual requirements established thereby between the exploration company (the explorer) and the government and the mines department or equivalent in each place. There are also a number of differences. I have prepared the paper on the basis that my audience will largely consist of -experienced explorers and the paper is intended to act as a brief refresher and a guide to the philosophy and the practicalities behind the legislation and practices in ground entry in each case. I will deal in turn with New Guinea, the Solomon Islands and then Queensland.

Jan 1, 1987

The value of Australia's education services exports increased to over $15 billion dollars in 2009, placing education as the third overall export earner behind coal and iron ore; however there are concerns over the impact of emerging policies on the future of both the industry and the provision of mining education. Policies have impacts on the growing number of international rankings (or league tables) of mining jurisdictions and universities. A high position in such rankings might be used as a measure of perceived quality with benefit to those at the top and to the detriment to those lower down.    Top performing companies in the relatively new domain of sustainability have been shown to achieve better financial performance than their industry competitors, assisting them in attracting top quality committed staff, hence positioning themselves well for the future. The world's mining companies, jurisdictions and universities are now ranked with results in the public domain. It is argued as to the validity of the data or perceptions used in such rankings, but there is no doubt they are influential in determining the flow of dollars around the globe. By investing your pension fund assets in the shares of the top performing companies, by placing your exploration dollars in a country at the top of such a list of attractive jurisdictions, attending or recruiting from a University at the top of the rankings - risk must surely be reduced?   While savings and risk reduction can undoubtedly result from the introduction of new technologies developed through appropriate R&D (the other core activity of a university), the maintenance of a very high level of exploration and production performance through dedicated highly skilled staff every hour of every day quietly improves financial performance, while avoiding safety, environmental and/or community incidents (ie protects the 'triple bottom line'). As always risk reduction comes down to enabling quality people to do a quality job - through the actions of such people we can sustain the global mining industry and secure our social license to operate. However, there is global concern over where the numbers of such people, including those with the recently required skills in sustainability, are going to come from.   This presentation will discuss some of the complexity and interactions involved in the development of such rankings, the dangers inherent in their simple acceptance and use, plus indicate some of the directions mining educators might take to sustain and increase the supply of quality graduates to the global mining industry. This is an ABSTRACT ONLY. No paper was prepared for this presentation.

Jun 1, 2010