Search Documents

By K. S. Seljesater

Since the development of dispersion-hardenable lead-antimony alloys' in the laboratories of the Western Electric Co., Inc., studies have been made of the effect of various third constituents on these alloys.2 This paper covers a study of the effect of small amounts of arsenic. This element is important since it occurs as an impurity in many commercial antimonial leads and the results obtained are particularly interesting as indicating a class of addition agents which exert a stabilizing effect on dispersion-hardened alloys. Experimental In order to study the effect of increasing amounts of arsenic, a series of alloys were made up containing 1 per cent. antimony, and arsenic varying from 0. to 0.10 per cent., the balance Doe Run lead (99.997 per cent. lead). The alloys were cast into bars 1 1/2 in. wide by 3/4 in. thick and cold-rolled to about 1/8 in- thickness. Three samples of each composition were annealed 1 hr. at 225" C. and quenched in water. One set was aged at room temperature, one at 50" C., and the third at 100" C., the

Jan 1, 1929

By K. S. Seljesater

Since the development of dispersion-hardenable lead-antimony alloys' in the laboratories of the Western Electric Co., Inc., studies have been made of the effect of various third constituents on these alloys.2 This paper covers a study of the effect of small amounts of arsenic. This element is important since it occurs as an impurity in many commercial antimonial leads and the results obtained are particularly interesting as indicating a class of addition agents which exert a stabilizing effect on dispersion-hardened alloys. Experimental In order to study the effect of increasing amounts of arsenic, a series of alloys were made up containing 1 per cent. antimony, and arsenic varying from 0. to 0.10 per cent., the balance Doe Run lead (99.997 per cent. lead). The alloys were cast into bars 1 1/2 in. wide by 3/4 in. thick and cold-rolled to about 1/8 in- thickness. Three samples of each composition were annealed 1 hr. at 225" C. and quenched in water. One set was aged at room temperature, one at 50" C., and the third at 100" C., the

Jan 1, 1929

By Louis Huntoon

THE USE of the aeroplane in engineering work is quite recent. Its general application to all branches of engineering, including mining and metallurgical engineering, is increasing and its possible uses are most promising. Comparatively little has been published on the sub-ject in the mining and metallurgical press, and it is for this reason that the following notes are recorded. In March, 1922, Prof. E. L. Bruce published an article in the Transactions of the Canadian Mining Institute showing the possible applications of the aeroplane to preliminary geological surveys. In October, 1922, Mr. DeShea, representative of the Fairchild Aerial Survey Co., of New York, discussed the subject before the New York Section of the Mining and Metallurgical Society. The writer has been in correspondence with the Laurentide Air Service of Montreal and engineers who have flown. Canada, with its many lakes and rivers-favorable landing places, meets the prerequisite for successful use of the aeroplane in an unexplored and uninhabited or sparsely inhabited country. During the open season hydroplanes are used, and during the, winter season ski runners are attached to the axle in lieu of wheels. With skiis attached it has been found practicable to take off and land on any depth of snow quite readily. Winter flying in northern Canada is quite common. The Laurentide Lumber Co., appreciating the value of the aeroplane, used them for two or three years for timber cruising, and about 1921 turned their equip-ment over to the Laurentide Air Service of Montreal, who operate flying machines. The photographic and engineering work in Canada is done by the Fair-child Aerial Surveys Co. under a contract with the Laurentide Company.

Jan 12, 1923

By C. L. Shapiro, R. Schempp

DuRing the past few years, general interest in the steel-producing and steel-consuming industries has been centered on the so-called "inherent characteristics" of steels. While often vaguely described, these characteristics are known to influence the response to heat-treatment and the hardening characteristics of the material. Although most of the recent papers and discussions have associated the "inherent characteristics" with the austenitic grain size and emphasized the importance of it, comparatively little is known of the variables that may affect the size of the austenite grain. The work to be described in this paper was carried out during the course of a study on the inherent characteristics of tool steel containing one per cent carbon. The discrepancies encountered in the determination and classification of the austenitic grain size led to an investigation of some of the variants influencing the austenitic grain size as determined by standard methods. Methods of Determining Austenitic Grain Size The present methods used for the determination of the austenitic grain size may briefly be classified in two groups: 1. Etching at room temperature to reveal the austenite grain size prior to cooling. 2. Etching at elevated temperatures, cooling to room temperature, and observing the structural conditions that existed at the temperature from which cooling occurred. The outstanding methods of the first group are: (1) the McQuaid-Ehn test, (2) optimum rate of cooling, (3) quenching and etching. McQuaid-Ehn Test.—This established and accepted test does not need much elaboration. It consists of pack carburizing at a definite temperature for a standard period of time and slowly cooling in the furnace. The temperature is 1700" F. (925' C.) and the time is 8 hr. The interpretation and evaluation of this test are fairly well defined in the A.S.T.M.

Jan 1, 1937

By Georges Millot

USUALLY the search for clays is left to chance in unexplored areas. A local working by the inhabitants or an outcrop is often the only guide. If the conditions of genesis of clays were always known, a set of general rules could be drawn up that would apply to this search. For example, a certain type of clay might be found wherever the sediment indicated a favorable environment. This paper sums up the considerable amount of knowledge that has been accumulated about the genesis of sedimentary days and offers some rules to be observed in prospecting for new clays. ANALYTICAL STUDY OF SEDIMENTARY CLAYS Clays may be found in many formations, both recent and ancient. All the intermediums exist between the deep-sea deposit and the mud deposited by a stream. In order to find out whether the nature of clay deposits depends on the environments in which they were formed, the samples used in the investigation described herein were very carefully chosen from: (1) ancient sedimentary series (a few from recent ones), (2) zones where conditions of genesis are typical. Ancient Formations Ancient formations were chosen because they are less difficult to sample than the bottom sediments of present-day lakes and seas. Moreover, a geo- logical section makes it possible to define the conditions of genesis of a deposit based on its facies, fossils, stratigraphic relations, and paleography. A present-day deposit is defined only by its aspect at the moment. Its previous history may have caused mixtures, alterations, and changes of environment, which escape detection. Typical Conditions of Genesis Samples from ancient deposits were taken from zones where typical conditions of genesis prevailed. Only clays from marine, lagoonal, and lacustrine environs are concerned in this study because the nature of the original en- vironments could be affirmed. In this way an inventory of the nature of sedimentary clays has been made for rocks formed in typical and individual environments; therefore the extent of the results that may be drawn from such a study will need discussion.

Jan 1, 1952

By J. B. Clark, A. S. Yue

IN recent years, zone melting1 has been applied extensively to the purification of metals having a very low vapor pressure.2-4 This note describes the zone melting of a high vapor-pressure metal, magnesium, where the melting takes place inside a refractory surface skin. The effects of zone speed and the number of passes of the molten zone on the purification have been determined and the effective distribution coefficients for the principal impurity elements were calculated. A schematic diagram of the zone-melting apparatus is given in Fig. 1. The Vycor tube containing the graphite boat with its magnesium charge (an extruded rod—3/8 in. in diam, 10 in. long) is pulled through the stationary furnaces. A molten zone approximately one-fourth the length of the charge is produced under each of the two central furnaces. Two grades of magnesium were studied—electrolytic magnesium and magnesium with a very low alloy content. The spectrographic analyses of these materials, within * 5 pct of the values stated, are given in Table I. Molten magnesium will vaporize severely if protected only by an inert atmosphere such as argon. Consequently an enveloping container is required. In zone melting, a rigid opaque container surrounding the charge is inconvenient because visual control of the zone length is prevented. A more satisfactory container is a strong flexible skin on the surface of the metal charge which is capable of supporting the molten zone. SO2 reacts with magnesium to form a thin coherent surface film of MgSO, and MgO. An atmosphere of SO, of commercial purity was maintained during the zone melting. Enough oxygen was present within the system and the commercial SO, for the satisfactory formation of the protective skin, so that any rupture of the skin during the zone refining was healed immediately.

Jan 1, 1959

By Anthony F. Lucas

Certain geological indications at Glady's station, four miles south of Beaumont, on the Sabine and East Texas railway (a branch of the Southern Pacific) induced me to undertake a thorough test of that locality by means of a well. I had been making reconnoissances for nearly two years in that part of Texas, before deciding upon this supreme effort. Three previous attempts had been made in the same place: one in 1894 by Messrs. Sharp & Co.; one in 1896 by Mr. J. Looney; and one in 1898 by Messrs. Savage Bros. They had all failed to pass though the immense thickness (500 ft.) of quicksand which underlies the surface soil, clay, etc. At first, I employed the system of boring which I had previously used in the Louisiana salt-deposits.* But I soon found that this method was inadequate, without modification, to deal with the quicksand. Accordingly, I adopted the use of large and heavy castings, and pipes of 12, 10, 8, 6 and 4 in. diameter, successively telescoped one into the other. Boring was begun by Messrs. Hamill Bros., of Corsicana, contractors, about the middle of October, 1900; and on January 10,1901, after many difficulties, a layer of rock containing marine shells was reached, at the depth of 1160 ft. For 150 ft. immediately above, the drill had passed through layers of sandstone and concretions of limestone. At this time there was about 600 ft. of 4-in. pipe, weighing at least 6 tons, in the well; and this, together with the next (6-in.) casing above, was filled with water. When the rock was penetrated the well " blew out," lifting the whole of the 4in. pipe. Mr. Hamill was on the top of the 60-ft. derrick when

Jan 1, 1902

By George Sachs, J. Spretnak

The process of recrystallization has not as yet been explained satisfactorily. Some definite conclusions could be drawn from recent investigations, such as, for example, that recrystallization is a process of nucleus formation and crystal growth1 and that the orientations of the nuclei correspond to some fragments of the original crystals, which have been considerably distorted during deformation.2 There are, however, a number of metals and alloys crystallizing in the face-centered cubic system, which form a particularly simple orientation if recrystallized as a sheet.3 Such a shect is almost a single crystal with the cubic axes parallel to the rolling, transverse, and normal directions of the sheet. This preferred cubic or (100) orientation of the recrystallized sheet has been considered to be very different from the rolling structure of the same metals,4 but there are two reasons why this last supposition remains open to controversial discussion. The first reason is academic: In practically all cases except the one mentioned above, close correlations and similarities between rolling and annealing orientations have been observed; for instance, in iron and steel sheet.6 Secondly, no deformed metal actually forms a simple orientation. In any thoroughly investigated case a number of different orientations and considerable scattering or deviations from the ideal orientations have been found.6 It is generally true that investigations on single crystals have shown that a definite orientation is approached in stretching or in compression of an originally undisturbed crystal.7 In the special cases, however, where the initial orientation was close to an important crystallographic direction that differed from the final "ideal" orientation, the resulting orientation changed very little by deformation, staying somewhere in the vicinity of the initial orientation.8 Such deviations

Jan 1, 1940

By George Sachs, J. Spretnak

The process of recrystallization has not as yet been explained satisfactorily. Some definite conclusions could be drawn from recent investigations, such as, for example, that recrystallization is a process of nucleus formation and crystal growth1 and that the orientations of the nuclei correspond to some fragments of the original crystals, which have been considerably distorted during deformation.2 There are, however, a number of metals and alloys crystallizing in the face-centered cubic system, which form a particularly simple orientation if recrystallized as a sheet.3 Such a shect is almost a single crystal with the cubic axes parallel to the rolling, transverse, and normal directions of the sheet. This preferred cubic or (100) orientation of the recrystallized sheet has been considered to be very different from the rolling structure of the same metals,4 but there are two reasons why this last supposition remains open to controversial discussion. The first reason is academic: In practically all cases except the one mentioned above, close correlations and similarities between rolling and annealing orientations have been observed; for instance, in iron and steel sheet.6 Secondly, no deformed metal actually forms a simple orientation. In any thoroughly investigated case a number of different orientations and considerable scattering or deviations from the ideal orientations have been found.6 It is generally true that investigations on single crystals have shown that a definite orientation is approached in stretching or in compression of an originally undisturbed crystal.7 In the special cases, however, where the initial orientation was close to an important crystallographic direction that differed from the final "ideal" orientation, the resulting orientation changed very little by deformation, staying somewhere in the vicinity of the initial orientation.8 Such deviations

Jan 1, 1940

By H. M. Chance

RECENT research work has shown that coal can be produced, at reasonable cost, from almost all coal-mining districts containing not more than 3 to 8 per cent. of ash. From coal so produced, an abundant supply of coke, suitable for blast-furnace operation, can be made containing from 12 down to 6 per cent. or less of ash. These statements apply broadly to the Appalachian coal belt, including most of the mining districts in Pennsylvania, Ohio, West Virginia, Kentucky, Tennessee, and Alabama. The exceptions will generally be found among those coals carrying a prohibitive percentage of sulfur. Any gravimetric heavy fluid method of separation will effect a reduction in the percentage of sulfur, but this reduction may not be sufficient to produce, from coal unfit for metallurgic use, a product that can be so used. When a large part of the sulfur is in the form known as "organic sulfur, "or is present as very .finely disseminated and homogeneously distributed pyrite, possibly it cannot be eliminated from the low-ash coal produced. When the sulfur exists as pyrite in distinct layers, bands, or nodules, or when it is finely disseminated but is irregularly distributed, often a low-ash coal low enough in sulfur to make good metallurgic coke can be produced from relatively impure coals. It has generally been assumed that the quality of coke on which blast furnaces must be operated depends on the geographic location off the furnace, and that the grade of coke on which a blast furnace must operate is that produced from the best coal obtainable by careful mining; or if the coal is prepared by washing, hand picking, or other means by which the foreign impurities are removed, that the grade of coke on which the furnace must operate depends on what has been termed the "inherent ash" of the particular coal.

Jan 6, 1924

By J. M. Vetter, W. F. Bowman

The Gulf Coast area of Texas and Louisiana produced a total of 47,070,650 bbl. of oil during 1928, a decrease of 7,401,173 bbl. from the previous year. Of this amount Texas produced 39,353,950 bbl., or a decrease of 9,689,296 bbl. from the 1927 output. The Louisiana Gulf Coast produced 7,716,700 bbl., which is an increase of 2,288,123 bbl. over 1927. The decrease in the Texas Coastal area is due principally to the decline at Spindletop. Production at the beginning of the year in this field averaged 53,400 bbl. daily. At the end it had declined to 35,850 bbl. The increase in Louisiana was due to development in new fields at Kelso Bayou (East Hackberry), Sulphur, Sweet Lake, Bayou Boullion and Sorrento. This production was maintained by the drilling of 984 wells. Of this number 736 were located in Texas and 248 in Louisiana. Of the 984 wells drilled, 571 were reported as producers. Distribution of the various completions is listed in the accompanying tables compiled by Oil Weekly. New Developments New developments of particular importance in Texas were the finding of a 5000-bbl. well in formations of Cook Mountain age in the Clay Creek field located in northern Washington County by the Sun Oil Co. ; the discovery of oil at Dewalt in Fort Bend County by the Humble Oil & Refining Co.; the development of commercial production at Raccoon Bend in Austin County by the same company; and the finding of oil in formations of Oligocene age in the Refugio gas field of Refugio County. The most important development in Louisiana was the finding of oil at Sorrento, east of the Mississippi River, by the Gulf Production Co. The importance connected with these finds is not so great in that they opened up new fields, but in the new territories which they open as possibly productive of oil. Eastern Louisiana has been looked upon with considerable doubt on account of the theory which has prevailed among most geologists that the nature of the formations was not such as to produce oil. The actual finding of oil in that area upsets this theory and

Jan 1, 1929

By John L. Schroder

INTRODUCTION-SYSTEM DESIGN The design of an underground mining operation requires the integration of transportation, ventilation, ground control, and mining methods to form a system which provides the highest possible degree of safety for mine personnel; the lowest cost per ton of product ; the most suitable quality of final product, considering its intended use; the maximum percent recovery of the reserve, consistent with cost and subsidence rights ; and the minimum disturbance to the environment. The selection of mining method is generally the controlling factor in overall mine design. Some important considerations in the choice of mining method are: 1) Depth of cover over the coal seam. 2) Strength and thickness of rock strata in the overburden. 3) Characteristics of the coal seam, including thickness, nature and location of impurities or irregularities, dip (or pitch), nature and direction of cleavage, hardness, and structural strength of the coal. 4) Nature and strength of the immediate roof (top) over the coal seam. 5) Nature and strength of the floor (bottom) under the coal seam. 6) Presence and amount of explosive gas (methane). 7) Quantity of water likely to be encountered in the mining operation. 8) Any previous or concurrent mining in seams above or below the coal seam to be worked. 9) Any restrictions on recovery required for subsidence control. Topographical and geological reports and maps of the area are usually available from state and federal geological surveys, and contain excellent general information to guide more detailed investigations. Exploratory drilling, and the plotting and analysis of the information thus obtained, are essential steps in any development program, and aid in the correlation and evaluation of information gained by other means. Other good sources of information are operating coal mines that may be in the same

Jan 1, 1981

By Arthur B. Foote

The cams at present universally used in stamp mills lift the tappets with an involute form of curve, to which the surface of the tappet is always tangent; moreover, the line of contact between tappet and cam, if produced, would pass through the center of the stem. This is no doubt a desirable feature, but the writer has long believed that it would be much more desirable if the cam were to pick up the stamp without shock, and gradually increase the upward velocity of the stamp throughout its upward movement. The involute form of cam attempts to impart instantly a considerable upward velocity to the stamp, starting it from a state of rest, and the result is a destructive blow, a great deal of noise, and much wear and vibration. The writer has developed a form of cam which will lift the stamp pith a motion similar to that of the piston of an engine between the end and middle of its stroke; in other words, harmonic motion, from the woint of zero to maximum velocity. The curve will give this ideal motion only when the stamp is set for the exact drop for which the cam was designed, but the improved cam will not be as bad as the involute cam until the drop is reduced one-half. In other words, if a cam is designed for a 6-in. drop, it will be some improvement over the usual form of cam until the drop is only 3 in. Any cam, whatever its form, must of course lift the stamp in the same number of degrees of revolution; therefore, with this new form, since the stamp starts more slowly on its upward course, it must end up by going faster, the average speed being the same as with the involute cam. The stamp, after it is no longer in contact with the cam, keeps on going up a certain distance, which is easily calculated. It is therefore possible to hang up a stamp without a cam stick, if the fingers are not more than + in. longer than necessary to hold the tappet above, the cam. With this design of cam the surface of the tappet is not tangent to the surface of the cam throughout the lift. The possible consequences of this were studied with a full-size model, and did not seem serious, as

Jan 1, 1915

By Nicholas J. Grant, Irmgard Rump, Bill C. Giessen

The system W-Hf was determined by use of metal -lographic and X-ray methods. The only interrnetal-lie phase W2Hf melts peritectically at 2650° ± 50°C. A eutectic between W2Hf and ß-Hf solid solution exists at 78 at. pct Hf arul 1930º ± 10°C. The addition of tungsten loulers the hafnium transfornzation; there is a eutectoid at 93 at. pct Hf and 1560°C. The solubility limits of the terminal solid solutions were determined. At the beginning of this investigation, the system had not been elaborated; only crystallographic work had been done to determine the structure of the occurring intermetallic compound W2Hf, and a certain analogy to the system W-Zr was to be expected. Special emphasis was placed in this program on the Hf-rich part of the diagram. Following the completion of our experiments, a phase diagram was suggested by Braun and RUdY.1 EXPERIMENTAL METHODS The investigation utilized tungsten powder supplied by the General Electric Co. with a purity of about 99.9 pct and hafnium crystal bar of about 97.7 pct purity, 2.3 pct Zr, supplied by Foote Mineral Co. Typical analyses are given in Table I. The procedures followed were identical with the ones described for the Re-Nb diagram.' Tungsten powder was compacted at 16,000 psi and the necessary amount of hafnium was added in the form of small pieces cut from the crystal bar, with a reasonable excess of tungsten powder to make up for powder losses on melting. High hafnium or tungsten melts were prepared from premelted tungsten and hafnium or by employing master alloys. The melting was done in a Heraeus arc-furnace under argon. Melting and remelting up to 8 times resulted in fairly homogeneous alloys. No weight

Jan 1, 1962

By L. C. McCabe

THIS paper is a progress report on a study, of the distribution of the banded ingredients (Figs. 1 and 2) in- Illinois screenings and the method of determining their distribution. Proximate analyses and screen tests1 have been reported and a further report on the washability characteristics of the screenings is in preparation. The microscopic study of the screen-ings is not yet far enough advanced to permit a conclusive report on the effect of mining, screening and washing on the distribution of the banded ingredients in the coals of Illinois. However, considerable fundamental data-have been collected as a background for the screenings investigation and for a proposed study of fuels composed of known quantities of vitrain, clarain and fusain, the three common banded ingredients of Illinois coals. These fundamental data and the preliminary information now available from the microscopic study of screenings are broadly indicative of the reaction of the coals to the physical processes affecting them in mining and preparation. Proximate analyses of samples of vitrain, clarain, and fusain from several Illinois mines have been published 2, but those given in Table 1 serve to show the differences that are apparent in proximate analyses. The vitrain samples are consistently low in ash, and the unit-coal value is uniformly lower than in clarain. The average .fuel ratio (F.C./V.M.) of the vitrain samples in the table is 1.57-whereas the clarain average is 1.42. The fusain analyses vary considerably in ash and moisture. In the two samples from this mine the moisture values range from 8.99 to 22.80 and the ash from 4.86 to 16.91 per cent. Fusain has higher fixed carbon than either vitrain or clarain but the percentage is erratic from sample to sample.

Jan 1, 1936

By Stanley L. Lopata, Eric B. Kula

The problem of preferred orientation has been considered in quantitative phase analysis by X-ray diffraction techniques. The average intensity of a diffraction peak can be obtained by integration over the whole pole figure, or by random rotation of the specimen in the X-ray beam, or by a combination of both. For rod or wire, where the pole figure shows rotational symmetry, the intensity is measured along a radius of the pole figure. Where no symmetry is present, rotational symmetry is imparted by rapid rotation of the sheet around its surface normal during measurement. These methods are applied to the determination of aus-tenite in an Fe-31 pct Ni rod and Fe-28 pct Ni sheet. X-RAY diffraction techniques are frequently used for quantitatively determining the relative amounts of two or more phases present in a structure.1,2 Briefly, the method requires a measurement of the intensity of a Bragg reflection for each phase. The method is based on the principle that the intensity of a Bragg reflection, IA, is directly proportional to the volume fraction of the given phase present, CA: T KRACA/2µ [1] where K is a constant independent of the diffracting phase, RA can be calculated and depends on the Bragg angle ? and the particular reflection measured, and µ is the linear absorption coefficient of the mixture.' For a mixture of two phases A and B, IA = RAcA [2] IA/IB=RAcA/Rbcb and CA+ CB = 1 [3] This allows the volume fraction of a phase to be calculated directly from the measured integrated intensities of the two phases present. This method is frequently used for quantitatively determining retained austenite in steels, but can be used for the quantitative determination of in titanium alloys, as well as phases in other alloy systems. The intensities are generally measured by diffracting only from planes whose normals are perpendicular to the specimen surface, with the implicit assumption being made that this intensity is typical of reflections from planes whose normals lie at other angles to the surface. If the specimen contains a texture or preferred orientation of the crys- tallographic planes by virtue of previous mechanical working, however, this measured intensity is correct only if the intensity level fortuitously is one times random. Examination of pole figures for actual rolled sheet shows that the intensity level at the center of the figure is seldom at the random level, and can very easily differ by a factor of five or more, leading to a commensurate error in the calculated amount of the phases. Textures have been commonly found in materials which are cold-rolled or recrystallized after cold rolling. This problem is becoming of greater importance since structural materials in use today, such as the high-strength stainless steels, frequently are further strengthened by cold rolling, and hence contain textures. Although high-strength carbon-containing alloy steels generally do not contain textures, some of the newer thermomechani-cal treatments will impart a texture even in these cases. In the case of hexagonal metals, such as titanium, probably every wrought sample will show some anisotropy. Since the standard X-ray techniques are inapplicable in all these cases, there is a clear need for some method of taking this anisotropy into account. The specific problem is to obtain the integrated intensity of a Bragg reflection for each phase, averaged over all orientations of the sample with respect to the X-ray beam. This can be done either by purely mechanical means or by a mathematical averaging. Mechanically, a small spherical speci-

Jan 1, 1965

By K. J. Gill, P. Chiotti, J. T. Mason

Thermal, metallographic, and vapor pressure data were obtained to establish the pkase boundaries and the standard free energy, enthalpy, and entropy of formation for the compounds in the Y-Zn system. Three coinpounds with stoichiometric formulas of YZn, YZn2, and Y2Zn17 melt congruently at 1105", 1080°, and 890°C, respectively. Four compounds with stoiclziometric formulas of YZn3, YZn4, YZn5, and YZn,, undergo perztectic reactions at 905", 895", 870º, and 685ºC, respectively. Three eutec-tics exisl in this system with the .following eutectic temperatures and zinc contents in wtpct: 875ºC, 23.2 Zn; 1015ºC, 51 Zn; 865ºC, 82 Zn. The YZn, pkase undergoes an allotropic transformation. In the two phase YZn2 -YZn alloys the trans.formation gives a weak thermal arrest at 750°C, whereas in the two phase YZn2-YZn3 alloys no thermal arrest is observed and the transformation occurs over a temperature range below 750°C. At 500°C the free mzergies of formation per lnole vavy from —18,090 for YZn to —53,430 fov YZr11 and corresponding enthalpies vary from -24,050 to -92,080. The free energies and enthalpies per g atom as a function of composition show a maximum for the YZn2 phase; the 500°C values are -9580 and -13,180, vespectively. 1 HE only information found in the literature on Y-Zn alloys was the observation reported by Carlson, Schmidt. and speddingl that Y-20 wt pct Zn forms a low melting alloy. The alloy was produced by the bomb-reduction of YF3 and ZnF2 with calcium in an investigation of methods for producing yttrium metal. The solubility of yttrium in zinc has been determined by P. F. woerner2 and reported by Chiotti, Woerner, and Parry.3 In the temperature range 495" to 685°C the solubility may be represented by the relation In these equations N represents atom fraction of yttrium and T is the temperature in degrees Kelvin. The purpose of the present investigation was to establish the phase diagram for the Y-Zn system and to determine the standard free energy, enthalpy, and entropy of formation for the compounds formed. MATERIALS AND EXPERIMENTAL PROCEDURES The metals used in the preparation of alloys were Bunker Hill slab zinc, 99.99 pct pure, and Ames Laboratory yttrium sponge. Arc-melted yttrium buttons contained the following impurities in parts per million: C-129, N-12, 0-307, Fe-209, Ni-126, Mg-13, Ca < 10, F-105, and Ti < 50. Some of the alloys containing 70 wt pct or more of Zn were prepared from yttrium containing 5000 ppm Ti as a major impurity. Tantalum containers were found to be suitable for all alloys studied and were used throughout the investigation. The pure metals, total weight about 30 g, were sealed in 1 in. diam tantalum crucibles by welding on preformed tantalum covers. A 1/8 in. diam tantalum tube was welded in the base of each crucible for use as a thermocouple well. Welding was done with a heli-arc in a glove box which was initially evacuated and filled with argon. The sealed crucibles were enclosed in stainless steel jackets and heated in an oscillating furnace at temperatures up to 1150°C. Homogeneous liquid alloys were obtained within a half hr at these temperatures except for alloys containing less than 20 pct zinc. The latter alloys were held at 1000º to 1100°C for 2 to 3 days in order to obtain equilibrium. After the initial equilibrations the tantalum crucibles containing the alloys were removed from the steel containers and used directly for differential thermal analyses. Further annealing heat treatments for alloys in which peritectic reactions were involved were carried out in the thermal analyses furnace. After thermal analyses the tantalum crucibles were opened and the alloys sectioned and polished for metallographic examination. In the following discussion alloys referred to as "quenched" were obtained by quenching the sealed stainless steel jacket containing the tantalum crucible and alloy in water. The differential thermal analyses apparatus used was a modified version of the one described in an earlier paper., The graphite crucible was replaced by an inconel crucible, the nickel standard and sampie container were separated by a 1/8 in. MgO plate, no getter was used, and provisions were made to

Jan 1, 1963

By M. L. Requa

This paper is abstracted from the report of the Appraisement Committee of the Independent Oil Producers&apos; Agency, of which the writer was Chairman. The other members of the committee were M. V. McQuigg and R. S. Haseltine. To Thomas Cox, engineer in charge of the investigation, and to his efficient staff of assistants, is due the credit for the detail work necessary in carrying out the plan of the Committee. It treats only of the valuation of the lands, wells, and piping, without going into details of equipment and other features. It was recognized, early in the operation, that the value of oil lands was the value of oil to be extracted, and marketed, less the costs attendant thereon. Referring this back to the costs in cents per barrel, it became obvious that surface improvements, absolutely necessary in the production of oil, from wells then drilled; had no separate and independent value aside from the value of the land, but that any excess equipment, not necessary for the production of oil from present wells, such as drilling tools, well casing, etc., should be given a present condition value. In valuing the properties of the Independent Oil Producers&apos; Agency, the Committee has considered the following facts: 1. That from each property there will ultimately be. produced a certain total quantity of oil. 2. That in the production of that oil a certain total quantity of money will be expended. 3. That a certain total amount of money will be received from the oil. 4. That the total net receipts will be the total gross receipts less the cost of development and production. 5. That the present value of the net receipts must be such an amount that when invested by a purchaser it will be returned with 8 per cent. interest additional during the life of the property.

Jan 2, 1918

By F. E. Minshall

FoR more than 30 years California has been one of the three leading oil-producing states. Present daily production of crude oil under curtailment, approximately 580,000 bbl., comes from three general areas: Los Angeles Basin, San Joaquin Valley, and the coastal region of Ventura and Santa Barbara Counties. This state produces approximately two-thirds of its oil from eight large fields, and obtains a daily average production of 48 bbl. of oil per producing well, whereas the average for the United States is but 8.15 barrels. During the closing stages of the first half of 1936, discovery of the Section Ten oil field was made, and credit goes solely to geophysical work. It is the first direct important discovery of oil in California that may be credited to geophysics. This discovery may furnish the cue to the means of discovering several fields in California, particularly in the San Joaquin Valley. It is a question, however, whether returns from geophysical work will play as important a part in the future supply of oil in California as have our former types of prospecting. Explobation Methods of prospecting have progressed in the oil industry through invention or improvement in scientific means of locating and defining structure and because of market improvements in drilling equipment. Present methods of prospecting include: 1. A detailed study of geology in an attempt to locate structural and stratigraphic conditions that would be favorable to the accumulation of oil. 2. Geophysical methods involving the use of the seismograph, torsion balance, magnetometer and electrical methods. (There is still much to be learned in California in the application of geophysical methods.) 3. Use of micropaleontology as an aid in correlation,. The principal improvements in drilling equipment are: 1. The Schlumberger dipmeter, which determines the direction of formation dip in an uncased hole.

Jan 1, 1937

By Ionel I. Gardescu

During the summer of 1930 the average daily oil production of Rumania registered a new peak at 128,000 bbl. per day. The estimated potential production as of September, 1930, was as high as 235,000 bbl. per day. During the latter part of the year, by mutual agreement, the operators decided to curtail their output to about 100,000 bbl., which brought the average for the year to 116,600 bbl. The total production for 1930 was 41,572,000 bbl. (last month estimated) as compared with 35,757,000 bbl. for 1929, or an increase of 16.3 per cent. over last year&apos;s production. The production for the last 10 years is given in Table 1. The curtailment of production was prorated per company, based on its total estimated potential production as of September, 1930, and not per field. As a consequence, at present there is little development of protected or slightly productive areas; viz., Arbanasi, with an average production of 1750 bbl. per day, dropped to less than one-third after curtailment came into effect. Moreni, with an average production of 92,000 bbl. per day, while producing 58 per cent. of the country&apos;s total output in 1929, went to 67 per cent. at the beginning of 1930 and to 75.2 per cent, towards the end of the year. The modified Mining Law of 1929 is still in effect. This law withdraws the restrictions set on foreign capital by the law of 1924. As a consequence a large percentage of proven state land was alloted through competitive bidding to foreign companies. The Romano-Americana (Standard of New Jersey) acquired several leases in the Boldesti and

Jan 1, 1931