Search Documents

By P. E. Landolt

MILITARY necessities and economic scarcities, occasioned by the first and second World Wars, led to the search for substitute materials and new products to meet the demands of advancing technology accelerated by research development. Among others, lithium came to attention. Its chemistry had been studied for a long period, but its general use was quite restricted due to limited known sources of raw material. In World War I, Germany used lithium metallurgically for two principal purposes: 1-hardened lead alloy, B-Metal, for railway bearings as a substitute for lead-tin-antimony alloys; and 2-light strong aluminum alloys, Scleron, in which zinc was largely substituted for copper.

Jan 12, 1951

By John B. Gayle

PRESENT flotation processes depend almost entirely on the buoyant properties of air bubbles to effect separations of mineral and gangue, but there is no convenient method for measuring aeration in flotation cells. Consequently the relation between aeration and cell performance has not been definitely established. In connection with a comparative study of kerosene and froth flotation processes, a modification of the displacement method' was developed in which air escaping from the cell surface is measured with a wet-test meter. The arrangement shown in Fig. 1 is satisfactory for use with a number of cells and is not critical, except that care must be taken to use connections and tubing large enough to avoid excessive back pressures. Attempts to use smaller tubing resulted in back pressures that caused displacement of the liquid level in the receiver, so that some air was lost around the sides, an occurrence readily visible when measurements were taken with only water passing through the cell. With the arrangement shown, the manometer indicated an average reading of about ½ -in. water pressure. No loss of air was evident.

Jan 7, 1958

By Carl A. Zapffee

FOR a number of years a puzzling phenomenon of brittleness in Class II ferritic stainless steels, developing in the temperature range near 475C, has received increasing attention, but its nature remains essentially unknown. During an investigation of the fractographic structures in stainless steels, conducted in the author's laboratory the past several years, principally under sponsorship of the Office of Naval Research, some observations of a new kind were found for "475 °C embrittlement." While the details of the study cannot be given here,' three fractographs will suffice to carry the

Jan 1, 1952

By J. M. Ohm, C. M. Bunker

Two special tools for recovering gamma-ray probes and logging cable from drillholes have been designed by Ohm and Bunker and constructed by Ohm. Though intended specifically for U. S. Geological Survey equipment, they may be used with other equipment of the same general type. Fishing Tool for Probes: A fishing tool of the overshot type (Fig. 1) was designed to retrieve logging probes (sondes) that become disconnected from the logging cable and are trapped in the drillhole. When the tool slides over the top of the gamma-ray probe, studs on the bottom engage the shoulder near the top of the probe (Fig. 2), which is then pulled to surface. The barrel can be constructed from brass or steel tubing. Wall thickness is not a critical dimension, but the tool should be heavy enough to sink through mud or water in the drillhole. The internal length of the tool must be enough to prevent interference with the upper end of the probe head as the tool slides over it. The design of the probe head used by the USGS required a minimum free space of 2 1/2 in. inside the fishing tool, which was made 7 1/2 in. long to increase the weight. The lower end, which engages the shoulder of the upper end of the probe, contains three studs placed at 120" around the circumference of the tool and held in the engaging position by the tension of a spring wire. The studs can be made of any metal, such as steel, having high tensile strength. As the tool slides over the probe the studs are pushed outward from the center against the spring tension, allowing the tool to slide into position below the shoulder of the probe head. The spring tension forces the studs inward into the engaged position after they pass the shoulder. When the tool is raised the studs stop against the shoulder, preventing the tool from sliding up over the top of the probe. Once it engages the shoulder of the probe it cannot be freed until both probe and fishing equipment are recovered from the drillhole.

Jan 1, 1960

By Charles F. Johnson

A pulse technique is described for the measurement of bar velocity. A low frequency sine wave pulse is used which allows the wave-length to become much larger than the lateral dimensions of the test specimen. The low frequency pulse method has been tested and compared with the resonant frequency method and the results show that both methods give, on the average, equivalent velocities.

Jan 1, 1971

By N. G. Johnson

ALL of us are only too familiar with the fact that first the defense program, and finally the war, required vastly increased production from existing sources, and the discovery and development of new sources of minerals and metals. For this vast program, the explosives industry was well prepared. I use the term "well prepared" to cover all the phases of explosives service, which include formulation, design, manufacture, distribution, and application.

Jan 1, 1944

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members) Member, aged 32. Fifteen years' experience in the mining, quarrying, and manufacture of gypsum and gypsum products, as purchasing agent, designer, operating manager and managing executive. Thoroughly familiar with the business in all branches, especially the organization of efficient producing forces and machinery and the value of cost and their application to manufacturing. Desires responsible position with a financially reliable concern in the same or similar business in which an interest may be obtained at a later date. Now doing consulting work, but free for appointments after April 1. New York or Philadelphia. No. 345. Member, technical graduate. Unmarried. Aged 32. Seven and one half years' experience in mining, timbering, and mine sampling. At present, and for past two and a half years, mine sampler for well known and highly successful mining company. Desire change. Go anywhere. Prefer assisting Mining Engineer. No. 346. Member, 40 years old. 18 years' experience in examinations and operation in the United States, Mexico and South America. Especially successful with poor class of labor. Open for engagement in any part of the world, in technical, administrative or consulting work. No. 347. Member, technical graduate. Sixteen years' experience as engineer, superintendent, and manager in metal mines. Exploratory . work, developing and equipping new properties. Operation of large mines, and various systems of mining. Low costs. Specialized in iron and copper mining, but have had some experience in zinc, lead and pyrite mining. No; 348.

Jan 4, 1917

By R. Clare Coffin

The production of petroleum in the Rocky Mountain district increased from 27,104,436 bbl. in 1929 to 33,048,630 bbl. in 1930. This increase was due to the development in southeastern New Mexico; which is in reality a portion .of the West Texas province. Disregarding production in southeastern New Mexico, the Rocky Mountain district produced 25,799,027 bbl. in 1929 and 23,164,988 bbl. in 1930, a decrease of 2,634,039 bbl. for the period. The daily production in January, 1930, averaged 70,839 bbl. for the entire district and in December, 1930, the daily production was 98,995 bbl. Total production by states is given in Table 1. Three important discoveries of oil and one of gas occurred in the district during 1930 in structures not, previously known to contain oil or gas. Oil was discovered in Dry Creek structure, Carbon County, Mont.; in the Midway structure, Natrona County, near Casper, Wyo.; and in the Greasewood structure, Weld County, Colo., northwest of Fort Morgan. Gas was discovered in the Bell Rock structure in Moffat County, western Colorado. Seven deep tests in as many different fields encountered oil in lower horizons than those already exploited. All of these discoveries were in the state of Wyoming. They occurred in the Salt Creek field, Natrona

Jan 1, 1931

By E. Eichen, G. S. Ansell. L. R. Sefton

A Technique for the Preparation of Thin Films of Two-Phase Alloys Suitable for Use in Transmission Electron Microscopy In order to obtain foil sufficiently thin to permit transmission electron microscopy of two-phase alloys, particularly alloys in which the second phase is present as a very finely dispersed second phase, a technique has been developed to permit the thinning of these materials without either the large degree of pitting present in the electrochemical or chemical thinning process or the slicing of the second phase particles accompanying the mi-crotoming process. The metal or alloy to be thinned is first ground to initial sheet thickness of approximately 0.002 in. by hand grinding on 4/0 emery paper. This starting sheet of material is then reduced in cross section by an air-abrasion technique using an S. S. White dental abrasive unit. This unit consists of a supply of compressed CO, which provides a stream of high velocity gas impinging on the metal surface. Incorporated in the machine is a hopper-type of device in which fine abrasive particles of alumina are introduced into this high velocity gas stream. The abrasive particles are irregular in shape, approximately 30 across. If any particles are introduced into the sample during thinning, they should be readily observable. Impingement of this gas abrasive mixture on the metal surface causes rapid removal of the metal in a rather uniform manner. The rates of metal removal may be adjusted by both regulating the gas pressure and amount of abrasive material introduced into the gas stream. By moving the gas stream abrasive mixture slowly about the specimen or sheet surface, a large area of the sheet may be uniformly reduced to a thickness which is then suitable for use in transmission electron microscopy. Attendant with this metal removal is a result in cold working of the metal surface due to the impingement of the abrasive particles. The resultant foils, therefore, if made from materials which are desirable to view in the annealed condition, have to be subsequently heat treated. If the alloy from which these foils have been made has been initially heavily worked or deformed during manufacture, then no subsequent heat treatment is, necessary as in the case of the SAP-type alloys. Following this initial abrasive thinning technique, the material is then given a final electropolish which is just sufficient to remove any oxide which has formed on the metal surface during the abrasion technique. Care has to be exercised in this technique to make sure that none of the attendant problems associated with the chemical or electrochemical removal process are encountered. An electrolyte solution which has been found suitable for aluminum-aluminum oxide SAP materials is one containing 78 ml of perchloric acid, 120 ml of distilled water, 700 ml of ethanol, and 100 ml of butylcellosolve. The current density used is 1 amp per sq cm and a polishing time of 3 sec on each side of the foil is used. Extreme care must be used in choosing the current density and time to ensure that just the oxide film on the specimen is removed. Times or current density which are greater than this will lead to perforation of the film due to the removal of the A1,0, particles or a complete loss of the film due to complete solution of the matrix. Once the oxide film is removed the specimens must be kept in alcohol until placed in the microscope to prevent any further oxidation. Fig. 1 shows -an electron micrograph at X28,000 of a thin foil of an aluminum-aluminum oxide SAP-type alloy prepared using this technique. The alloy consists of a matrix of commercial purity aluminum containing a very finely dispersed second phase of aluminum oxide flakes. In the electron micrograph, the dark patches are the aluminum oxide particles. The lighter portions of the micrograph are the aluminum matrix. Within the aluminum matrix, the dislocation structure of the alloy is clearly visible. This structure consists of intersecting twin boundaries and single dislocations. No abrasive particles were observed in the samples. In addition, thin films of commercial purity aluminum were prepared using this method and observed in the electron microscope. Here also, there was no evidence of abrasive particles introduced in the samples. The technique presented provides a satisfactory method for the production of thin films of aluminum-aluminum oxide SAP-type alloys for use in transmission electron microscopy where none of the usual thinning techniques appears to be satisfactory.

Jan 1, 1962

By M. E. Kukura, L. G. Stevens

As described in a previous presentation and in various patents, the Minerals Sciences Div. of UOP, Inc., has developed a modified reduction roast ammonia leach process for nickel laterites. This process gave considerable improvement in extraction over the conventional Caron approach as practiced in Cuba, Australia, and the Philippines. This greatly improved response was obtained with a wide variety of ores. This paper describes the pilot plant flowsheet and reviews the design features unique to the UOP process. Operating results from pilot plant campaigns are compared with bench scale results. Operating problems and their solutions are also discussed.

Jan 1, 1976

Jan 1, 1908

By G. Almgren

Swedish cut-and-fill mines are described with regard to location, production volumes, and grades. Development goals (such as higher productivity and better working conditions) are presented, and different methods of development, such as mechanization, new layouts, etc., are discussed. Development methods are described with examples from drilling, loading, haulage, and rock mechanics. Special attention is paid to filling techniques. Figures are given for productivity and relative costs.

Jan 1, 1977

By W. E. Curran

For years the geographical isolation of the Southern iron-ore district from the great producing centers in the North and East enabled it to meet its conditions and solve its own problems without regard to the practices and policies of other districts, but during the past few years distances have been shortened, practices and wages are being standardized, .and these changing conditions have brought new problems to the South.

Jan 1, 1937

By P. Gordon

An isothermal jacket microcalorimeter, supplemented by metallographic, microhardness, and X-ray measurements has been used to study the isothermal annealing of high purity copper after room temperature tensile deformation. The amount of stored energy released during annealing has been measured as a function of deformation in the range 10.8 to 39.5 pct elongation. The data have shown the major heat effect to be associated with recrystallization and have allowed an analysis of the recrystal-lization kinetics and the calculation of activation energies of recrystallization. WHEN a metal is deformed plastically, some of the energy expended is dissipated as heat during the working process, while the remainder is stored within the metal in the form of lattice distortions and imperfections. During subsequent heating of the metal, the distortions and imperfections can be largely annealed out and the associated stored energy released as heat. It is apparent that measurements of the evolution of stored energy during such annealing may produce important information concerning the nature of the annealing mechanisms and the imperfections involved. Some excellent studies of this type have been made in the past, notably those of Taylor and Quinney,' Suzuki,2 Bever and Ticknor,3 Borelius, Berglund, and Sjöberg,4 and Clarebrough et al.5,6 None of this work, however, employed isothermal techniques, with the exception of the Borelius studies' in which only the early annealing stages were investigated. Since isothermal measurements, as compared with heating or cooling curve, have the merits that 1—they reveal the kinetics of a process more clearly, 2—the results obtained are more easily applied to theory, and 3—most fundamental investigations of annealing using techniques other than calorimetry have been carried out isothermally, it was considered important to apply calorimetry to the study of the isothermal annealing of metals. Accordingly, an isothermal jacket calorimeter of the Borelius type,' supplemented by metallographic, hardness, and X-ray measurements, has been used to study the annealing of high purity copper after room temperature tensile deformation. Experimental The microcalorimeter has been described fully elsewhere." Briefly, the specimen to be studied is placed in a constant temperature environment of virtually infinite heat capacity achieved, as shown in the drawing of Fig. 1, by means of a vapor thermostat. A high thermal resistance is provided between the sample and the environment and a sensitive differential thermopile (see Figs. 2 and 3) arranged with half its junctions in contact with, and thus at the constant temperature of, the environment, and the other half in contact with the sample. A reaction in the sample develops a small difference in temperature, AT, across the thermopile, which is followed by a recorder-galvanometer set-up as a function of time, t, and is converted to reaction heat per unit time, P, by the use of the equation AT P=a?T + b AT dt The constants, a and b, in Eq. 1 are determined by a simple calibration, making use of the Peltier heat developed by a small current run through the junction of a thermocouple located in an axial hole in the specimen (Fig. 2). In its present form, the limit of sensitivity of the calorimeter is a heat flow of 0.003 cal per hr. The copper used was the spectroscopically pure metal supplied by the American Smelting and Refining Co. in the form of 3/8 in. diam continuously cast rod, reported to be 99.999+ pct Cu. A small amount of the copper was available at the start of this work and is referred to hereafter as lot A. A second batch, lot B, was obtained later, most of the results described subsequently being for this lot. As will be seen, there is some indication that lot A was somewhat purer than lot B, but it is not known whether this difference was present in the as-received metal or arose during subsequent handling. The two lots of copper were remelted and cast into two 1½ in. diam ingots in vacuo, using high purity graphite crucibles and molds. The ingots were upset several times to break up the large cast grains, and then rolled and swaged to rods 0.391 in. in diameter, using several intermediate anneals with about 40 pct reduction in area between anneals. The penultimate anneal was 2 hr at 350°C. X-ray examination showed no marked general preferred orientation in the resulting rods. The grain structure typical of the two rods is shown in the micrograph of Fig. 4." It was found to be virtually im- possible to get an unambiguous measure of the absolute grain size in the two annealed rods because of the profusion of annealing twins and the lack of regularity of the grain boundaries. However, counts of the number of boundaries intersected per unit length along a random line on a polished section, making a correction for the proportion of boundaries (about half) estimated to be twin boundaries, gave a figure of about 0.015 mm for the average grain diameter. The grain size of the rod from lot A was about 5 pct smaller than that from lot B. The rods were cut into 1 ft long bars and these deformed in tension at room temperature to various total elongations in the range 10.8 to 39.5 pct. A strain rate of 1 pct per min was used. The deformed bars were then stored in a dry ice chest until such time as samples were to be cut from them. Five bars deformed as indicated in Table I were used for the subsequent tests. In all cases, all the calorimeter.

Jan 1, 1956

By AIME AIME

The following changes of address of members have been received at the Secretary's office during the period of Jan. 1 to Mar. 15, 1907. This list therefore supplements the annual list of members corrected to Jan. 1, 1907, and brings it up to the date of Mar. 15, 1907. The names of members who have accepted election during January and February, 1907 (new members), are printed in italics. The large number of changes of address since Jan. 1, 1907, shows the importance of publishing these changes as frequently as possible, and the Bi-Monthly Bulletin has been selected as the means to present this information to the members of the Institute. By a simple method of cutting out these names and addresses and pasting them directly over the corresponding names in the annual list of members, the record can be kept practically up to date, and the value of the list correspondingly increased. For this purpose the changes of address have been printed only on one side of the page. The names of new members, being in italics, are readily distinguished from the others, and can be pasted in approximate alphabetical order on the margins of the pages.

Mar 1, 1907

By A. E. J. Engel

The New York talc deposits of commercial importance are in St. Lawrence and Lewis counties, in the northwest Adirondack Mountains (Fig 1). All of the deposits are of pre-Cambrian age and occur within highly deformed and recrystallized marble of the Gren-ville series. The deposits in St. Lawrence County, near Gouverneur, are the largest and most productive of their type known in the Western Hemisphere. In 1948 the seven mines which are in operation will produce about 130,000 tons of ground talc. All talc production in Lewis County is from one mine. There the annual production ranges from 15,000 to 30,000 tons. These so called talcs of New Yorb State include earth materials of different chemical and mineral compositions. In general the mineral talc is subordinate in amount to other minerals in both the Gouverneur and Natural Bridge deposits. In the Gouverneur district the mineral talc comprises less than 25 pct of the mined and ground rock. Most of the rock mined is a tremolite- or tremolite-anthophyllite schist somewhat altered to serpentine and talc. This characteristic in no way tlevaluates the "talc" for certain markets, and in some instances makes the material more desirable. The Natural Bridge talcs include types high in serpentine, as well as complex aggregates of serpentine, talc, carbonates, and diopside. Usage of the term talc, however, for

Jan 1, 1950

Jan 1, 1912

Jan 1, 1913

By C. D. Jardine, D. G. Patton

Rapidly increasing energy costs and more rigid customer quality requirements necessitate improved control of pelletizing processes. With the introduction of dedicated microprocessor-based controllers, sophisticated control strategies are now possible. An application of this technology at Carol Project has resulted in fuel savings, improved pellet quality, and standardization of operating procedures. This was accomplished with no production loss by using a "building block" approach to design and equipment selection.

Jan 1, 1985

[ARTICLE I. NAME AND OBJECT Section 1. This Society shall be known as the Society of Petroleum Engineers of the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. Section 2. The object of the Society of Petroleum Engineers shall be to furnish a medium of cooperation among those interested in the petroleum-natural gas industry an to promote the advancement of this branch of mineral technology through meetings to stimulate the preparation, reading, discussion and circulation of papers connected therewith. ARTICLE II. MEMBERS Section 1. Any person who is a member of AIME may become a member of this Society by the specified process. Section 2. Local organizations may be formed by the Society of Petroleum Engineers as subsidiary units, the membership of which shall be subject to and in accordance with the by-laws of the Institute.]

Jan 1, 1961