Search Documents

By Ernest Stütz

(New York Meeting, October, 1913.) THE problem of increasing blast-furnace efficiency through diminution of flue-dust production while operating with burdens consisting largely of fine ores has of recent years attracted the attention of metallurgists, whether directly or indirectly interested in the economies of iron smelting, and the various methods evolved from theory or practice have been. submitted to wide discussion. After the very thorough and, at that time, exhaustive view of the whole subject, which was afforded to the industry by the meeting of this Institute in February, 1912, the subject was again taken up at the meeting of the Verein deutscher Eisenhüttenleute at Düsseldorf in December, 1912. While American and German conditions are not entirely identical, it may be of interest to give here the words of the gentleman summing up the discussion at the Düsseldorf meeting : ?The chief advantage offered by the use of briquettes lies in the fact that disturbances in the furnace, caused mostly by the presence of fine ores in the burden, are avoided, and that blast pressure can be considerably reduced. The resulting economies cannot be overrated, as, with lower blast consumption per ton of product, the installation will be able to take care of increased production. In consequence of lower pressure and speed of blast, heat is more efficiently utilized,, flue gas temperature is lowered, and coke particles are less liable to be carried along with the flue dust, of which considerably less is produced. Finally, by increased regularity of operation and higher temperature in the lower parts of the furnace, the quality of the product is improved. The question of briquetting iron ores has grown to be one of the most important in the iron industry, and it is not any more a question of what is the cost 'of briquetting a ton of ore, but what, in. using ore briquettes, is the cost, of: production of a ton of iron."

Jan 7, 1913

By C. H. Jr. Herty

FEW subjects have attracted the attention of metallurgists more than ,oxygen in steel. From the days of Mushet and Ledebur interest in this subject has been increasing, and as additional knowledge has become available, the problem has naturally grown more complex. Instead of using the simple term "oxygen" we now distinguish between iron oxide, silicates of various kinds, oxysulfides, oxygen as gas and oxygen in solid solution in steel. There are five general methods for determining oxides in steel: hydrogen reduction;, vacuum fusion; various wet-extraction methods, including electrolytic methods; methods depending on volatilization of the iron away from the oxides; and metallographic methods. For oxygen in solid steel each of these methods has both advantages and disadvantages. The hydrogen-reduction method is of no use on steels above about 0.20 per cent. carbon;1 furthermore, it gives only FeO and possibly some MnO. The vacuum-fusion method2 is expensive and gives total oxygen, with the exception of some A1203, and does not differentiate between the various oxides in which the oxygen exists. Most of the wet-extraction methods' give only the more insoluble oxides Si02 and A1203, though the iodine method gives MnO to an uncertain degree (information that may be more misleading then no information

Jan 1, 1930

By Jamie Deuel

The a ad on Connection" For the purpose of this paper, we will concentrate on the ubquitous radon gas as the principle, low-level radiation effect from uranium tailings piles. Standards are also proposed for gamma radiations but, by most accounts, this is much less of a low level problem than is radon. I am also aware of some just completed research at Oak Ridge National Laboratories that suggest polonium may be a major concern in tailings, but those data are preliminary at this time. What is radon gas? In the first place it is not a gas in the accepted sense in that it has no driving pressure head. It might prove a more convenient description to call it radon vapor. Radon vapor, then, is 7-1/2 times heavier than air. Radiologically, it is an alpha emitter which means it spontaneously gives off high ionizing potential but low penetrating power particles. In fact, the alpha particle has such low penetrating power that this sheet of paper will completely shield a person. The problem, though, is breathing the radon decay products, called radon daughters. If radon daughter products are ingested into the lungs, their alpha emissions may cause cancer. The principle carcinoma associated with breathing radon, or more basically, associated with radiological effects is oat cell car- cinoma of the undifferentiated mall cell type. Radon has a 3.8 day half life which means in less than four days half of its initial radioactivity has decayed away. In less than a month it essentially becomes inert or non-radioactive. The Tailings Situation The NRC, in its April 1979 Generic Environmental Impact Statement

Jan 1, 1983

By John C. Smock

The ten years, 1879 to 1888, inclusive, have been notable in the history of iron-making for the great rise during the latter part of 1879 and the earlier half of 1880; for the maximum of production in 1882 ; for the gradual decline and the reduced product through 1883,1884 and nearly to the end of 1885; then, for the recovery through- 1886 and 1887; and the extraordinary outputs of our iron furnaces during the last three years. The price of pig-iron might be taken as an index to the condition of the iron-mining industry, and if represented graphically, they would shorn approximately parallel curves. The mining industry cannot always respond quickly to a rise in price and an increased demand for ore; nor can its production drop simultaneously with sudden falls in price of iron and of ore. Hence, the irregularities of the one are not reflected in the other. The statistics of the iron mines collected by the United States census, for the year ending June 30, 1880, exhibit admirably their condition at that time. The reports received from mine owners and managers, of the production for the year 1888, furnish the basis for a comparison and supply data for some notes on the changes in the iron-mining industry in New York which have taken place in this period of time. The iron-ores of New York may be grouped in the following districts: I. The Highlands of the Hudson (magnetites). II. The Lake Champlain and Adirondack Region (magnetites). III. St. Lawrence and Jefferson Counties (red hematites). IV. Clinton and Wayne Counties (fossil-ores of the Clinton Group). V. Dutchess and Colnmbia Counties (limonites). VI. The Hudson River (carbonates). VII. Staten Island (limonites). The ores of the first and second districts, as enumerated, are almost exclusively magnetites; those of the third and fourth are hematites;

Jan 1, 1889

By E. F. Sumner, C. K. Eilerts

A partial differential equation was developed and programmed to compute the cumulation and flow of the liquid phase of a gas-condensate fluid. It was found that such cumulation near the wellbore may attain saturations permitting liquid flow within periods of the order of 1 day. The radius at which this saturation obtains advances toward the external reservoir boundary with continued recovery, although it may move only 2 to 5 percent of that distance during the productive life of the well. This relatively high saturation can cause a serious dimunition in delivery capacity. The pressure dilferential required for flow of gas through a formation with such saturation may be as much as three times greater than the corresponding differential in a formation where saturation is less than 2 percent. Because of the radial geometry, total reservoir pressure differential required for flow with a zone of relatively high liquid saturation about the well was indicated to be two to three times greater than without the saturation. INTRODUCTION A computing program developed by the authors 1 to integrate the partial differential equation for transient radial flow of gas-condensate fluids required a prevalued function, W(Po) = kD(p0)/M(p0)z0(Po).......(1) related to cumulation of condensate in pores of the reservoir as pressure declines. Methods were available for relating mobility to saturation, saturation to liquid-vapor volume ratio, liquid-vapor volume ratio to pressure and, hence, mobility to pressure to obtain W(pD). However, certain assumptions had to be made in advance of program execution concerning movement of the liquid phase and change in radial distribution of liquid saturation as recovery progressed. Because reservoir fluid mobility and related pressure gradients are markedly dependent on liquid saturation, it was desirable to eliminate the necessity for these assumptions and in this respect improve the reliability of a result obtained by integration. Experimental research was begun to determine the relationship of variables that control the reservoir flow of low liquid-vapor ratio fluids. With the porous medium partly saturated, permeability to a two-phase flowing fluid could not be measured because the viscosity was unknown. Viscosity could not be measured without knowing permeability of the liquid-containing medium; but mobility, the ratio of permeability to viscosity, was measurable. This property, and liquid-vapor volume ratio of the flowing phases, have values determined by nature of the fluid and porous medium and, in addition, were found to be pressure, velocity and saturation dependent. A program developed by Kniazeff and Naville 2 for computing multicom-ponent, two-phase flow used polynomials to represent saturation dependence of permeabilities for gas and for liquid phases, and an effluent viscosity constant under reservoir conditions. The authors developed a program based on a partial differential equation of similar mass balance origin but designed to represent distribution of an unlimited number of components between gas and liquid phases utilizing the experimental information available as to variable dependence. Attention was given to liquid-vapor volume ratio of the flowing phases, a property which is essential as a liquid saturation boundary condition. A program for computing implicitly saturation increase at uniform intervals along the drainage radius was combined with an existing program for calculating pressures, and the two were used alternately in an iterative solution for both saturations and pressures. The function W(pD) needed for calculating pressures was replaced by the ratio of mobility to compressibility factor. BASIC EQUATIONS The partial differential equation for calculating

NEW MEMBERS The following list comprises the names of those persons who became members during the period Feb. 10 to Mar. 10, 1915: Members BANKS, HAROLD PURDY, Min. Engr 61 Broadway, New York, N. Y. BARAGWANATH, JOHN G., Min. Engr., Morococha Mining Co.; Morococha, Peru. BEESON, JOSEPH JOSIAH, Min. Geol Stanford University, Cal. CALLOWAY, ALFRED W Pres., Davis Coal & Coke Co., Cumberland, Md. DEETRICK, JAMES W., Mgr., Republic Iron & Steel Co., 826 Pennsylvania Ave., Youngstown Ohio.

Jan 4, 1915

By Augustus Locke, Edward H. Perry

In the exploration of a copper deposit by drilling, obvious advantages are to be gained from a distinction between primary and secondary ore.' Perhaps the chief of these is the aid which such a distinction renders in determining where a given hole should stop. The copper assay, often a sufficient guide, cannot always be exclusively relied upon. Primary ores may extend downward indefinitely and may fluctuate in value independently of depth: if primary ores are consistently lean for a considerable vertical distance, there is little reason to expect that, still deeper, they will increase to the commercial grade; on the other hand, rich primary ores may persist uninterruptedly downward or may come in again below a lean interval. Secondary ores, however, have a comparatively limited vertical extent; in a large way enrichment decreases with depth and finally gives out. It follows then, that when a hole descends from profitable ore into ore of less than the commercial minimum, the practical significance of the situation depends upon whether this decrease results from a decrease in secondary enrichment or is a variation in primary content: if the copper of the ore passed through has been chiefly secondary, little is gained in the average case by extending the hole much below the point at which the commercial limit is reached; but, when copper is chiefly primary, due weight must be given to the possibility that, still deeper, the ore may again improve. The distinction between primary and secondary ore may of course be effected through an examination of the drillings. It has been found, however, to be facilitated by curves made by plotting assays against

Jan 1, 1916

By W. O. Hotchkiss

Rock exposures are usually a very small part of the surface area in any mining district and the prospector and geologist must base their deductions as to the area, extent, and structure of various formations upon exposures that seldom form 5 per cent. of the area studied. Most often, outcrops form less than 1 per cent. of an area, so that exploration for mineralized contacts or mineral-bearing formations necessitates drilling, test pitting or tunneling, shaft sinking, and other underground work. In these days of high costs any method that will give definite facts regarding rock? obscured by soil or other material should be used to the greatest possible extent. In the early days of the Lake Superior iron districts, mines were located in the few places where ore was present in outcrops. Later, larger orebodies have been found, in depressions, obscured by soil and other foreign material. Mineralized rocks are oftentimes more weathered, softer, and more easily eroded than unmineralized rocks. It is quite natural, therefore, to expect that such orebodies (particularly where large enough to influence erosion in former physiographic conditions) should lie in depressions and be obscured by later debris. It is not difficult to believe that the history of the development of Lake Superior iron mining may be duplicated in other mining districts, that even larger orebodies than those first mined may be found in areas where the rock exposures, which led to original discoveries, are few or lacking. The chief properties of rocks that can manifest themselves through an obscuring cover are magnetism, electrical effects, radio-activity, gravity, and sound transmission. All of these have been used, to a small extent, to tell us a few things about what lies below the surface that we could not otherwise determine, but none has been used so long and so widely as

Jan 1, 1923

By W. O. Hotchkiss

Rock exposures are usually a very small part of the surface area in any mining district and the prospector and geologist must base their deductions as to the area, extent, and structure of various formations upon exposures that seldom form 5 per cent. of the area studied. Most often, outcrops form less than 1 per cent. of an area, so that exploration for mineralized contacts or mineral-bearing formations necessitates drilling, test pitting or tunneling, shaft sinking, and other underground work. In these days of high costs any method that will give definite facts regarding rock? obscured by soil or other material should be used to the greatest possible extent. In the early days of the Lake Superior iron districts, mines were located in the few places where ore was present in outcrops. Later, larger orebodies have been found, in depressions, obscured by soil and other foreign material. Mineralized rocks are oftentimes more weathered, softer, and more easily eroded than unmineralized rocks. It is quite natural, therefore, to expect that such orebodies (particularly where large enough to influence erosion in former physiographic conditions) should lie in depressions and be obscured by later debris. It is not difficult to believe that the history of the development of Lake Superior iron mining may be duplicated in other mining districts, that even larger orebodies than those first mined may be found in areas where the rock exposures, which led to original discoveries, are few or lacking. The chief properties of rocks that can manifest themselves through an obscuring cover are magnetism, electrical effects, radio-activity, gravity, and sound transmission. All of these have been used, to a small extent, to tell us a few things about what lies below the surface that we could not otherwise determine, but none has been used so long and so widely as

Jan 1, 1923

By Michael Hoch, Walter C. Wyder

The isothermul section of the Nb-Ti-Zr-O system at 1500°C was investigated using X-ray dzffraction and metallographic techniques. UP to 66.7 at. pct 0, the system contains nine four-phase regions. Tsopleths at 10, 20, 30, 40, 50, and 55 at. pct 0 weye constructed. The purpose of this investigation was to determine the general shape of the quaternary equilibrium phase diagram of niobium, titanium, zirconium, and oxygen at 1500°C. The system was truncated at 66.7 at. pct. O., PREVIOUS INVESTIGATIONS The Ti-Zr-O system was investigated in this laboratory.' The binary systems of interest have been compiled and discussed by anssen2 and Levin, McMurdie, and Ha11. Elliott4 has determined the Nb-O system by metallographic and X-ray diffraction techniques. He shows the existence of three oxides, namely NbO, NbO2, and Nb2O5. At 1500°C the solubility of oxygen in niobium is about 4 at. pct. No solid solubility region is shown for either NbO or NbO2. EQUIPMENT The same equipment as that for the study of the Ti-Zr-O system was used. The X-ray diffraction patterns were analyzed with the help of the ASTM card set5 and NBS circulars.6 MATERIALS The niobium powder (99 pct pure), the titanium powder (99.6 pct pure), the niobium pentoxide, and the zirconium dioxide used in this study were purchased from the Fairmount Chemical Co., Newark, N.J. The zirconium powder (99.4 pct pure) was obtained from the Charles Hardy Co., Inc., N.Y. Reagent-grade titanium dioxide was purchased from the Matheson Co., Inc., Norwood, Ohio. The oxides were dried in air at 700°C for 24 hr before use. Though the materials used were not "hyper-pure," the impurities present do not affect the results (lattice parameters, phase boundaries), within the experimental accuracy. PROCEDURE Samples of the desired compositions were made up, in mole pct, from the materials listed above. In some cases the intermediate binary compounds, such as NbO and TiZrO4 were prepared beforehand and used in the preparation of the samples. This technique enabled equilibrium to be reached from two sides. The components of each sample were mechanically mixed in a mortar and pestle and pressed into 3/16-in. diam pellets. The pressures used in compacting were of the order of 50 to 100 x 103 psi. Sintering was accomplished by heating the samples in a tungsten crucible (3/4-in. high, %-in. diam, 1/8-in. wall, lid with XB-in. hole). The pellets were separated from each other and from the crucible by means of small spiral coils of tungsten wire placed between the stacked pellets and on the bottom of the crucible. The sintering time was from 4 to 12 hr at 1500°C under a vacuum of 6 x 101-5 to 1 x 10-6 mm of Hg. All samples were reground after the first or second heating repressed, and reheated. In most cases: equilibrium was obtained after the first heating, as the X-ray diffraction pictures after each heating remained unchanged. Quenching of the samples from 1500°C was at first only possible by allowing the crucible and its contents to lose heat by radiation. The temperature dropped from 1500° to 900°c in approximately 1 1/2 min, which was considered adequate when compared to the times used by other investigators to reach equilibrium in the temperature range of 1000°c and lower. Later, a new technique for faster quenching of the samples was cleveloped. This technique involved the removal of the samples from the crucible, whereupon they were quenched by coming in contact with the water-cooled copper base of the furnace. This manipulation was performed without breaking the vacuum. The sample pellets were placed on a tungsten wire rack inside the crucible. The wire rack passed through the hole in the crucible lid, where it was connected to a small nonmagnetic chain. The chain was fed to the side of the furnace by means of a brass rack which fitted between the body and lid of the furnace. Suspended at the end of the chain, near the furnace wall, were three magnetic washers. With the use of a strong

Jan 1, 1962

By R. W. Jenkins, O. J. Neslage

The need for mechanized drilling to decrease mining costs has resulted in the development of the jumbo from column-and-bar drill carriages to hydraulically controlled jib jumbos. Resultant savings from use of improved jumbos have been high enough usually to retire the machinery investment within a year. The jib jumbo unit has been applied successfully to development and preparation programs and flat-bedded stopes, and an even wider field is forecast for its use.

Jan 1, 1950

By R. V. Vines, E. M. Wise

It is known qualitatively that the recrystallization behavior of platinum is dependent upon the amount and particularly the nature of impurities present, the amount of prior cold-work and the annealing time and temperature, but published data are limited. A study of the effects of cold-work and annealing temperature on the hardness of a sample of very pure platinum was undertaken to supply part of this information. Conclusions 1. The platinum used in the experiments had a probable platinum content of 99.99+ per cent, and had the following mechanical properties in the completely softened condition: Vickers hardness number, 39.4; ultimate tensile strength, 19,340 lb. per sq. in.; proportioilal limit, very low; elongation, 37.5 per cent in 2 inclles. 2. The effect of cold-rolling on the hardness is shown in Fig. 1. The hardness increases rapidly up to 10 to 15 per cent reduction and more slowly up to about 75 per cent reduction, beyond which it increases more rapidly. 3. The recrystallization temperatures for a 15-min. anneal, after cold-rolling 19, 39.5, 50.8, 66, 80.5 and 89.5 per cent reduction in thickness, are approximately 765°, 700°, 635°, 600°, 545' and 425°C., respectively. 4. The recrystallized grain size of this platinum is a function of the percentage of cold reduction, being larger the lower the percentage of cold-work. 5. Little or 110 grain grourtll resulted from subjecting recrystallized samples to higher temperatures or annealing for longer times. Prior Work As already mentioned, data on the recrystallization of platinum are scarce. Gmelin'sl handbook, which summarizes data published earlier than August 1938, lists values ranging from 400' to 810°C. for the minimum temperature of recrystallization of samples with rather indefinite

Jan 1, 1940

By E. M. Wise, R. V. Vines

It is known qualitatively that the recrystallization behavior of platinum is dependent upon the amount and particularly the nature of impurities present, the amount of prior cold-work and the annealing time and temperature, but published data are limited. A study of the effects of cold-work and annealing temperature on the hardness of a sample of very pure platinum was undertaken to supply part of this information. Conclusions 1. The platinum used in the experiments had a probable platinum content of 99.99+ per cent, and had the following mechanical properties in the completely softened condition: Vickers hardness number, 39.4; ultimate tensile strength, 19,340 lb. per sq. in.; proportioilal limit, very low; elongation, 37.5 per cent in 2 inclles. 2. The effect of cold-rolling on the hardness is shown in Fig. 1. The hardness increases rapidly up to 10 to 15 per cent reduction and more slowly up to about 75 per cent reduction, beyond which it increases more rapidly. 3. The recrystallization temperatures for a 15-min. anneal, after cold-rolling 19, 39.5, 50.8, 66, 80.5 and 89.5 per cent reduction in thickness, are approximately 765°, 700°, 635°, 600°, 545' and 425°C., respectively. 4. The recrystallized grain size of this platinum is a function of the percentage of cold reduction, being larger the lower the percentage of cold-work. 5. Little or 110 grain grourtll resulted from subjecting recrystallized samples to higher temperatures or annealing for longer times. Prior Work As already mentioned, data on the recrystallization of platinum are scarce. Gmelin'sl handbook, which summarizes data published earlier than August 1938, lists values ranging from 400' to 810°C. for the minimum temperature of recrystallization of samples with rather indefinite

Jan 1, 1940

By Robert S. Archer, Zay Jeffries

It is about fifteen years since the development in Germany, largely by Alfred Wilm, of the aluminum alloy called duralumin. In this alloy, combining as it does the tensile strength of mild steel with the lightness and corrosion resistance of aluminum, a distinctly new material was presented to the engineering world. Despite the evident usefulness of this material, however, its commercial development has been slow, due in part to the difficulties involved in its fabrication. In view of the potentially great utility of strong aluminum alloys, it seemed desirable to find means of producing such alloys with better fabricating properties, and work was undertaken with this object in the laboratories of the Aluminum Company of America several years ago. This work has resulted in the production of two new types of aluminum alloy of the "strong alloy" class, having distinctly improved fabricating qualities. The knowledge gained has also made it possible to produce alloys of the duralumin type with greater strength and hardness than previously obtained. There have thus been made available some new engineering materials which it is the object of this paper to describe. These alloys, induding duralumin, are fundamentally wrought alloys. Castings of the same compositions heat treated in the same manner give inferior physical properties, particularly as to ductility. The statements made subsequently concerning properties and heat treatment apply to material that has received sufficient working to thoroughly break down the cast structure. The material referred to has, in general, undergone a reduction in section of at least 80 per cent, by mechanical working. It may be mentioned in passing that other compositions have been found that are suitable for the production of the maximum physical properties in heat-treated castings.

Jan 1, 1925

By D. W. Fuerstenau

Measurement of zeta potentials is a useful tool to study the surface chemistry of minerals under flotation conditions. Because there is continued interest in this approach, the apparatus for obtaining zeta potentials of nonconducting solids by the streaming potential method is outlined here. Fig. 1 illustrates the streaming potential apparatus. The streaming potential cell or plug consists of two 24/40 standard ground joints (4) joined with a piece of pyrex tubing 60 mm long and 12 mm in diam (5). The electrodes are made of bright platinum disks 19 mm in diam and 1 mm thick through which 0.5-mm holes have been drilled (6). To the surface of each is welded a piece of 80-mesh platinum gauze. Each electrode is permanently mounted on the ends of the inner parts of the two standard joints by means of a platinum wire (7) which connects it to the tungsten seal at the end of the cell (8). For ease in cleaning and handling the apparatus, the streaming cell is fastened to the 500-ml reservoir flasks (1) by means of two 18/9 ball and socket joints (2). This particular arrangement permits passage of the solution in either direction through the plug of particles. Flow of solution can be stopped by a stopcock (3). One of the reservoir flasks has a large opening to permit insertion of either a thermometer or a pair of electrodes for measuring pH of solutions within the system. In making the experiments, the plug is filled with 48 to 65-mesh particles, but a layer of 28 to 35-mesh particles is placed at each electrode to prevent any of the finer particles from passing through holes in the electrodes.

Aug 1, 1956

By AIME AIME

ON April 7 the twentieth national Open-hearth Conference of the A.I.M.E. will be held in Birming¬ham, Ala., in conjunction with a meeting of the Committee on Blast Furnaces and Raw Materials. At least 300 engineers and operators are expected to attend. Birmingham, the industrial city and iron, and steel center of the South, has been called the "Magic City." Men actively engaged in business in Birmingham today have seen practically every building in the business district erected, have witnessed the establishment of every existing industry, and have hunted birds cm the site now one of the busiest corners of the business district. Incorporated as a town in 1871, the city today has a population of more than 380,000 in its metropolitan area. It is

Jan 1, 1937

By David M. Cregger

The performance of the nation's first geologic repository for Commercial High Level Waste will be evaluated in a variety of ways which will involve the use of the state-of-the-art thermomechanical computer codes. Elastic properties of the host rock and the materials surrounding the repository are required for this numerical modeling effort to assess both near- and far-field effects. Only limited laboratory testing is possible, however, making it extremely beneficial to expand the data base by calculating dynamic elastic properties from available geophysical well logs. Elastic theory dictates that for an isotropic solid there are only two independent variables in addition to mass density, namely the compressional velocity, the shear velocity, and Poisson's Ratio. Compressional velocity and density are readily measured by geophysical well logs or in the lab; the crux of the solution requires measuring or determining either the shear velocity or Poisson's Ratio. Examination of acoustic propagated shear waves measured during confined compression testing demonstrates that Poisson's Ratio is a fundamental lithology-dependent parameter. Once a rock mass is appropriately classified, application of the laboratory derived dynamic Poisson's Ratio will yield a continuous and reasonable in situ modulus from acoustic and density logs. For preliminary characterization and assessment of the mechanical properties of rocks within the subsurface, and for studies of rock quality, this method is sufficiently accurate. The general availability of acoustic and density logs from wells logged for other purposes has made the application of this method desirable.

Jan 1, 1984

By R. P. Marshall

This note describes positive evidence that hydrogen in titanium alloys diffuses under the influence of a thermal gradient. The experiments confirmed the expected similarity of this system to the H-Zr system and produced qualitative information on the magnitude of the heat of transport for hydrogen in titanium alloys. This effect has practical importance in applications where titanium alloys operate in a thermal gradient under conditions such that hydrogen embrittlement may develop within the expected lifetime of the structure, for example in supersonic aircraft service. The theories of thermal-gradient diffusion may be found in recent reviews and experimentation in this field by Shewmon,1 Sawatzky,2 Markowitz,3 and Darken and Oriani.4 The basis for Soret thermal diffusion is the "heat of transport", denoted by Q*. This is an energy term for the amount of heat (energy) transferred by atomic diffusion, and can be either positive or negative signifying a driving force for atomic diffusion to the cooler or hotter region, respectively. Experimentally, Q* is determined by plotting the natural logarithm of the point-to-point concentrations after exposure to a thermal gradient vs the respective point-to-point temperatures in units of the inverse absolute temperature scale. The slope of the straight line is Q*/R, R being the gas constant. For the titanium experiments, specimens (3 by 1 by 1/16 in.) of a) commercially pure titanium, b) the 8 Al-1 Mo-1 V titanium alloy, and c) the 6 A1-4 V titanium alloy were exposed to thermal gradients of 6° to 115°C per in. for 18 days at 250° to 550°C. The temperature gradient was in the direction of the 3-in. dimension. The hydrogen concentrations existing after exposure were determined on sections of the specimens by vacuum extraction. Three sections of unexposed sheet of each alloy were analyzed as standards to allow a check for hydrogen

Jan 1, 1965

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members) The following is a partial list of members and guests who called at Institute headquarters during the period Mar. 10, 1917, to Apr. 10, 1917. George S. Blair, Pittsburgh, Pa. E. P. Mathewson, Toronto, Canada. H. M. Boylston, Cambridge, Mass. T. Poole Maynard, Atlanta, Ga. F. J. Brule, Toronto, Canada. . W. J. Mead, Madison, Wis. M. B. Cohen, Miami, Ariz.. D. G. Miller, Denver, Colo. W. M. Corse, Buffalo, N. Y. P. N. Moore, St. Louis, Mo. F. G. Cottrell, Washington, D. C. R. H. Morris, Ansted, W. Va. E. C. Cross, Cleveland, 0. W. J. Morrison, Toronto, Canada. Nelson Dickerman, San Francisco, Cal. M. F. Ortin, Petrograd, Russia. F. N. Flynn, Chuquicamata, Chile. G. W. Paymal, New York, N. Y. F. L. Garrison, Philadelphia, Pa. Edward H. Perry, Boston, Mass. J. S. Grasty, Charlottesville, Va. 0. G. Petersen, Somerset, Ky. H. D. Hibbard, Plainfield, N. J. H. C. Price, Bartlesville, Okla. H. L. Hollis, Chicago, 111. C. A. Richardson, Toronto, Canada. F. H. Jackson, Marysvale, Utah. Hallet R. Robbins, Vancouver, B. C., Can. W. Strickler Jones, Silver City, N. M. A. H. Rogers, Boston, Mass. E. B. Kirby, St. Louis, Mo. H. G. Smith, Princepulca, Nic. J. M. Lovejoy, Electra, Tex. Edwin G. Steele, Van Horn, Tex. A. F. Lucas, Washington, D. C. 'S. A. Taylor, Pittsburgh, Pa. Edwin Ludlow, Lansford, Pa. A. P. Thompson, Salt Lake City, Utah, E. Francis McCrossin, Birmingham, Ala. Milton A. Allen is now engaged in the New York office of Messrs. Arthur L. Pearse & Co. Percy E. Barbour, managing editor of the Engineering & Mining Journal, has been appointed, by Governor Whitman, Deputy Superintendent of Police of the State of New York.

Jan 6, 1917

By D. Muraoka

Introduction Soda ash, anhydrous sodium carbonate, is produced from underground trona deposits occurring in the Green River Basin of southwestern Wyoming. Stauffer Chemical Co. of Wyoming, a jointly owned subsidiary of Stauffer Chemical Co. and Rocky Mountain Energy Co., mines the trona and processes it into high-purity soda ash. Stauffer Wyoming has been in operation since 1962 with a current production capacity of about 1.8 Mt (2 million st) per year of soda ash. The refinery has five parallel operating trains using the monohydrate process which is a series of chemical processing unit operations described below. Screening and Crushing The mined trona is brought to the surface in two counterbalancing ore skips. The ore is initially screened with refinery feed (less than peagravel size material) entering the process. Oversize is conveyed to an outdoor stockpile. Ore is recycled from under the stockpile via cone feeders as the refinery needs require. The ore is conveyed to hammer type crushers and screened. The refinery feed enters the process and the oversize is recycled to the crushers. Calcining The first step in refining trona to soda ash is calcining the trona ore. This is accomplished in concurrent flow, rotary kilns that are direct fired with natural gas. [2 (Na CO NaHCO 2H O) Heat 3Na CO + 5H20 + CO 2 3~3~ 2 ~~2 32] The trona ore is fed to the kiln at the burner end and is intimately mixed with the hot exhaust gases from the burner. Direct contact with the flame is avoided. The ore moves down the kiln by gravity and rotation aided by the kiln's internal lifters. The exhaust gases are cleaned to 99 + % particulate removal and discharged to the atmosphere. Dissolving the Calcined Trona The calcined trona is conveyed from the kiln discharge to a rotary drum dissolver where it is mixed with water and weak solution (unsaturated solution of calcined trona in water). The calcined trona is soluble whereas the impurities, primarily shale, are insoluble. The discharge from the dissolver is a slurry containing saturated solution (about 30% dissolved calcined trona in water), some undissolved calcined trona, insoluble impurities, and organic impurities. The dissolver discharge enters a rake classifier that makes the first solid/liquid separation in the process by removing the heavy undissolved material from the saturated solution. This undissolved material is conveyed to a second rotary drum dissolver and mixed with water to dissolve any remaining calcined trona. The secondary dissolver discharges to a second rake classifier that separates the solids from the liquid. The solids are now primarily insoluble impurities with very little unrecovered calcined trona. These wastes are conveyed to evaporation ponds for disposal. The liquid from the secondary rake is recycled to the primary dissolvers' weak solution system. Returning to the primary rake classifier, the saturated solution which contains suspended insoluble muds is pumped to a thickener. Flocculant is added to aid settling of the suspended muds. The flocculated muds are collected at the bottom of the thickener and pumped to vacuum cloth filters. The adhering saturated solution is separated from the muds that remain on the filter cloth. The recovered solution is returned to the dissolvers' weak solution system. The muds are reslurried and pumped to the evaporation ponds for disposal. Saturated solution, containing some suspended insoluble muds along with the organic impurities, overflows the thickener. Filtering the Saturated Solution The saturated solution overflowing the thickener enters a holding tank where it is pumped to a bank of pressure leaf filters. The suspended muds are captured on the filter leaves while the cleaned saturated solution is pumped to polishing filters. The polishing filters are also leaf pressure type, intended to remove any suspended solids that may pass the primary filters. Organic impurities are removed with activated carbon. The purified solution is now free of insoluble muds and has most of the organic impurities removed. Crystallizing and Drying the Monohydrate The purified saturated solution is pumped to evaporative crystallizers. The solution is circulated from the crystallizer vessel through a heat exchanger. Indirect contact with steam in the heat exchanger causes the saturated solution to boil, thus crystallizing the soda ash in its monohydrate form. Slurry crystal density is maintained in the crystallizer by simulta¬neous feed of fresh saturated solution and drawoff of the slurry.

Jan 1, 1986