Search Documents

By S. A. Falconer

Much attention and publicity has been given, during recent years, to grinding, classification, flotation, and thickening. The various technical papers, and symposiums held to discuss these important phases of milling, have contributed to a better understanding of the fundamental principles and operating variables involved. Another important part of milling— to the flotation operator—is a treatment step to which frequently too little attention is given—"conditioning," or the treatment the ground mineral pulp receives before it enters the flotation machines. "Conditioning" is a hackneyed and frequently misused term, commonly employed to describe the pretreatment of surfaces of minerals in ore pulps or mill products prior to froth flotation. In general, such pretreatment is for the purpose of changing the flotation characteristics of these mineral sur- faces to enable them to respond in some desired predetermined manner when subjected to flotation. Taggartl states that the function of conditioning is "either to insure selective collector coating of one mineral species while another species is not; or to take such steps as will compensate for departure therefrom." As 0. C. Ralston has stated? ... we are still faced with the fact that some mineral particles are water-avid, others air-avid, and that by properly modifying them they may be enhanced or diminished in desirable or undesirable avidity. Coatings on minerals must still be assumed to fall into three classes: (1) a coating of immiscible oil, (2) a layer of adsorbed substance, (3) a chemically produced coating. It is submitted that the process of preparing mineral surfaces for subsequent flotation treatment should take into consideration physical as well as chemical means for altering the normal flotation response of the mineral surfaces. A more descriptive word than "conditioning" is needed to designate broadly these procedures. The minerals in many ores cannot be made to respond in a normal manner to usual methods of "conditioning" with selectivity modifying reagents, until they have been cleansed, or interfering slimes and soluble salts have been removed from the ore. Therefore, it appears important to include under the general subject of "conditioning" a discussion of the purposes, methods used, and some of the advantages of these pretreatment steps. This is dealt with under the subject heading " Initial Treatment of Mineral Surfaces and Ore Pulps." Under this broader interpretation, the methods employed for treating mineral surfaces to alter their flotation characteristics may be divided into three general classes: 1. Physical methods.

Jan 1, 1950

By G. T. Lineberry

Power requirements for a piece of mobile mining equipment are largely dependent on the set of conditions in which they must operate. These conditions are isolated and key parameters are identified. The effect of operating conditions on power determination is investigated. A simulation technique is developed to predict ranges of power demands for off-highway haul units as an archetype, permitting the analysis of changeable operating conditions. This program uses given data, conditions, and probabilities and ranges to solve for individual components of power, which can then be summed. By adopting such a technique, a systematic and rational determination of power is made possible. The usefulness of this basic approach in the determination of power requirements for other mobile mining equipment is emphasized.

Jan 1, 1983

By Felix Wunsch

WHILE the effect of the cold-junction temperature has been known by many, its consideration has been ignored in a number of installations, resulting at tunes in a very considerable error. In fact, the magnitude of this error may amount to over 100° in some cases. While hand-operated correcting devices for portable checking pyrometers may be entirely satisfactory, it is, of course, desirable to have such apparatus en¬ Millivoltmeter Thermocouple Platinum Wire Mercury FIG. 1.-EARLY `METHOD OF AUTOMATICALLY COMPENSATING FOR COLD-JUNCTION TEMPERATURE CHANGES. tirely automatic, when applied to curve-drawing or printing pyrometers, otherwise there is no assurance that the record is correct. Numerous methods for automatically compensating for cold-junction temperature changes of thermocouples have been proposed and used in connection with millivoltmeters. One of the earliest proposed was that shown in Fig. 1. A bare resistance wire was immersed in a column of mercury located near the cold junction of the thermocouple. An increase in temperature near the cold junction resulted in a rise of the mercury column, which short-circuited more of the resistance wire causing an increase in the potential difference across the millivoltmeter, which compensated for the decreased electromotive force of the thermocouple.

Jan 9, 1919

By E. E. Bauer

Technical data describing the critical points for selection of the proper hammer and of the boom and power pack for mounting on mobile gyratory crusher installations are presented. Charts describing typical rocks with breakability indexes for hammer selection are included. Comparative data of representative available hammers along with criteria for evaluating hammer selection are also presented. Factors affecting the selection of the boom and the power pack, as well as optional features for ease of operation and improved safety are described.

Jan 1, 1986

By N. A. DeCecco, H. M. Meyer

IN the early stages of a titanium brazing investigation, binary titanium systems partially or completely known and fundamental metallurgical data were surveyed to select the pure metal most likely to be satisfactory for producing a ductile high strength joint. The phase diagrams for the purpose of this survey were classified into two groups: 1—systems with large solubility in ß titanium, but negligible solubility in a titanium, and 2—systems with large solubility in a titanium. Those metals with melting points believed to be too high or too low for titanium brazing (Tim = 1730°C) were eliminated from consideration. The melting points of vanadium, tungsten, tantalum, hafnium, zirconium, and the platinum group are too high and those of zinc, lead, cadmium, and tin are too low. The remaining metals were grouped as follows: 1—large ß solubility: Cr,¹ Mn,² Fe;³ CO,4 Ni,5 Cu,6 Be,' Si." —large a solubility: Al.9

Jan 1, 1954

By Harold S. Davis

SURROUNDING the nuclear core of an atomic energy plant there are usually one or more thick walls of concrete, as required to protect instruments and personnel from the harmful effects of nuclear radiations. Sometimes these massive walls are of ordinary concrete weighing about 150 pcf. To reduce wall thicknesses, concrete weighing 200 to 350 pcf may be used. Such high densities are obtained by using natural aggregate processed from heavy ore, or by using steel slugs or iron shot in concrete. Mix data for a number of high-density concretes are summarized in Table I.1 High density at low cost is of prime importance in shields designed to absorb gamma rays. On the other hand, biological shields located near the reactor core must attenuate neutrons as well as gamma rays. In general, a biological shield should contain: 1) heavy elements to slow down high energy neutrons and to absorb gamma rays, 2) either light elements or hydrogenous materials to moderate neutrons of intermediate energy, and 3) materials to absorb neutrons once they have been slowed down to thermal energies. Some shield materials, iron and water for example, are effective in one or more of the above ways. On the other hand, some otherwise excellent shield materials have certain undesirable radiation properties that limit the ways or number of places they can be used. For example, when iron absorbs neutrons it emits secondary gamma rays of high energy. On the other hand, boron absorbs neutrons avidly without producing high energy gamma rays. In spite of its high cost, boron is sometimes used in concrete to minimize production of secondary gamma rays. In some shielding applications it is necessary to avoid materials that become radioactive when subjected to neutron bombardment, continuing to give off high energy gamma rays for long periods after being removed from a neutron field.

Jan 5, 1957

By W. A. Hoyer, G. A. Lock

Laboratory and field tests have shown that it is feasible to log for copper in a qualitative way using the techniques of neutron activation analysis. Laboratory tests showed that the 0.51 and 1.04 mev gamma rays of 62Cu and 66Cu, respectively, could be diagnostic. However, in the core holes, the detection of copper was limited to 0.3% concentration because of interferences from the 18Si and Al gamma rays. Both stationary and continuous logs were made, but only the stationary data yielded a recognizable copper response. This response consists of a combination of two effects-the direct response from copper at 0.51 mev and an increase in low energy gamma ray absorption due to mineralization. Both low energy chemical (PuBe) and high energy accelerator neutron sources were used for the laboratory and field tests, while the same 2 X 5 in. Nal scintillation detector served for all the tests. Potential improvements in copper detection might be possible with solid state gamma-ray detectors which have better gamma ray resolution but much less detection efficiency. This type of activation logging requires complex equipment and trained personnel to conduct field operations and may find application where coring is difficult or prohibitive.

Jan 1, 1973

By Heinrich A. Kortmann

Specifications on the chemical, physical and metallurgical properties of the blast furnace burden are steadily becoming more stringent, especially in those countries where higher raw material and energy costs can be overcome only by improved technology. This paper describes the test methods for the relative predetermination of the criteria where the effects of temperature, gas composition and physical load in the blast furnace are duly considered. Data are presented to show the correlations between burden material tests and blast furnace results. Possible test methods for the direct reduction process are also discussed.

Jan 1, 1977

By Philip Bucky

THE general conception of a mine model is that of a three-dimensional object representing the mine workings, the orebody and the country rock of a particular property. Its chief uses have been to make it easier to understand the mine and to serve as a basis for the arguing of legal questions. Fayol endeavored to use mine models in a different way and to all students of subsidence "Fayol's dome theory" is of decided interest. We have more recently the suggestion of Young and Stoek of the University of Illinois, who1 suggest the use of models as a means of studying the problem. Prof. Henry Briggs, of the University of Edinburgh and Herriott Watt College, also makes use of models to determine the effects of bending at the edges of extensive workings.2 It is interesting to note that civil engineers are taking a decided interest in the application of models and the principles of dynamic similarity to the solution of their problems. The Proceedings of the American Society of Civil Engineers for 1930 contain an elaborate article by Benjamin F. Groat,3 who says, in his opening remarks: "Every engineer should know and understand that a model constructed in accordance with Newton's theory of similarity is not only the means for reproducing the complexities of flow, or other mechanical action, on a small scale, but that models may be made the best means of designing works of great magnitude. In the present state of knowledge, a properly constructed and properly tested model will answer the difficult questions of hydrodynamics much more quickly and accurately than the most profound mathematical analyses." A study of P. W. Bridgman's book on Dimensional Analyses leads one to arrive at the same conclusion.

Jan 1, 1931

By G. Nabi, W-K. Lu

Cylindrical specimens of natural dense hematite were reduced to magnetite at atmospheric pressure in H2-H2O mixtures of known composition over the temperature range 1084° to 1284°K. The rate of reduction was measured by the rate of movement of the interface between hematite and magnetite. The diffusion of gases through the gaseous boundary layer, the magnetite layer, and the interfacial chemical reaction were all considered in the interpretation of experimental data. The mass transfer coefficient through the boundary layer was calculated using accepted correlations. Values of the chemical reaction rate constant and the diffusivity of hydrogen in the magnetite phase were determined. THE present investigation is concerned with the reduction kinetics of natural hematite to magnetite by H2-H2O mixtures in the temperature range 1084" to 1284°K at atmospheric pressure. This reaction is the first step in the series of topochemical reactions in the process of reducing hematite to iron. Kinetic information of the simple steps such as hematite-magnetite transformation is necessary in order to have a better understanding of the complex processes of hematite reduction in iron-making. It also has direct industrial significance because magnetic roasting is one of the most important methods in benefication of lean ore.&apos; Although many technical papers have been published on the process of magnetic roasting and iron oxide reduction, very little information is available in the literature concerning the fundamental nature of hematite reduction to magnetite by reducing gases. Hansen et al.2 reduced the dense synthetic pellets of high-purity oxide in CO-CO2 mixtures and determined the reaction rate by weight-loss method. They were able to interpret most of their results by applying the interfacial area control theory developed by Mckewan.3 In contrast, Wilhelm and St. Pierre,4 who studied reduction of hematite to magnetite in H2-H2O mixtures by weight-loss method, stressed that the resistance of the porous magnetite layer to the diffusion of gases cannot be neglected in consideration of the overall reaction rate. In the present study the contributions of interfacial chemical reaction, diffusion of gases through the magnetite phase, and the gaseous boundary layer to the overall reaction rate will be considered. APPARATUS AND PROCEDURE Hematite Specimens Preparation. Natural hematite ore from Vermillon range of Northern Minnesota was selected for the present investigation because of its high purity and thermal stability. Chemical analysis of five samples gave the following average values: 67.52 pct total iron (96.62 pct Fe2O3, 0.28 pct FeO, 0.03 pct metallic iron), 2.53 pct SiO2, <0.07 pct MgO, 0.03 pct CaO, 0.05 pct combined mixture, 0.07 pct loss on ignition, and 0.34 pct other. Cylindrical specimens of 0.93 cm in diam and 2.7 cm in length were drilled from slabs of ore with a water-cooled diamond core drill. These specimens were heated to 1000°C and furnace-cooled. Specimens with silica pockets developed large cracks. The uncracked specimens were heated a second time, and their surfaces were carefully examined with a microscope. Those with hairline cracks or surface inhomoaenitv-- were rejected. Preparation of H2-H2O Mixtures. H2-H2O mixtures were prepared by the combustion of H2-O2, mixtures in a pyrex glass chamber in the presence of a catalyst. Alumina pellets coated with palladium, supplied by Englehard Industries, were used as the catalyst. Purified grades of hydrogen and oxygen were used which were repurified by usual techniques. Hydrogen before entering the combustion chamber was passed through an activated alumina H2O absorption bulb, with copper turning at the top. The cover of this bulb was not made pressure-tight so that any pressure development in the hydrogen line would cause the cover to blow off and also the copper turnings would act as a flame arrester in the case of a flashback from the combustion flame. Oxygen flow rates were measured with a bubble flow meter after purification with 1 pct accuracy. Hydrogen flow rates were measured by "precision wet test meter" and the amount of unburnt hydrogen was accurately measured by a bubble flow meter, after condensing water vapor in the gaseous stream. The Pyrex glass bulb contained concentric Vycor glass tubes as shown in Fig. 1. Oxygen was prevented from diffusing into the hydrogen line by threading platinum wire through pores at the combustion end of gas inlet tube. The glass bulb was heated with a Kanthal heating wire pasted in asbestos paper. The surface temperature of the bulb was measured with a thermocouple and adjusted to remain at approximately 350°C. The gaseous reaction chamber also served as a preheater for gases to avoid thermal segregation. The following sequence of operation was adopted. 1) Nitrogen was passed through the outer concentric tube to purge the catalyst bulb of oxygen. 2) Hydrogen was introduced through the inner tube until a steady flow was obtained. 3) Oxygen was then introduced into the nitrogen stream passing through the outer tube. 4) When combustion had commenced and a flame was visible over the platinum wire, the N2 was turned off.

Jan 1, 1969

By Robert O. Davis, Phillip A. Abbott

The response of geologic materials subject to nuclear weapon effects is of considerable interest in the design of buried protective construction. Recently, more consideration has been given to placing such structures in rock rather than in soil. Although rock has the obvious advantages of high strength and low deformability, discontinuities such as joints and fault planes severely complicate any response analysis. Nevertheless, some knowledge of the effects of these discontinuities must be developed, even if that knowledge remains largely qualitative in nature. In this paper, we present a constitutive description of cracked rock subject to uniaxial shock loading. The constitutive equations are based on certain average response characteristics of a particular cracked rock model. Rather than attempt to represent each material discontinuity individually, we have incorporated the discontinuity effects into constitutive relationships for a continuous medium. The resulting equations are suitable for use in hydrodynamic computer codes presently used for ground motion calculations. APPROACH The continuum description which will be presented below is based on a detailed analysis of a particular cracked rock model. This model can be visualized as a sequence of plates (representing the intact rock) separated by gaps (representing the discontinuities). This so-called "plate-gap" model was first used by Thouvenin (1) in an effort to explain the behavior of porous materials at high

Jan 1, 1971

By E. H. Bronson

PROPERTY of Malartic Gold Fields Ltd. is situa-ated in the great clay belt in the northern part of the Province of Quebec. This belt represents the floor of the glacial lake Barlow-Ojibway. The clay blanket has a gently rolling, almost flat surface, with here and there projecting knobs and ridges that outline the large irregularities of the surface on which the clay was deposited. At irregular intervals glacial eskers dominate the landscape. The ore-bearing country rock is covered by strata of clay, sand, and silt to a depth varying to 40 ft. There are serious structural problems when it is necessary to place loads of unequal intensities on this surface to support buildings and machinery for a modern mining plant. Earlier mining companies and their engineers paid little attention to the science of soil mechanics, partly because they believed it unnecessary and partly because they knew little of the subject. The results are evident in some of the tottering structures in older camps. Careful analysis of soil problems is well worth-while, since cost of foundations may vary from 20 to 50 pct of the final cost of a structure. Low operating and maintenance costs can be achieved only in this way. If it is definitely established that a plant will be in operation for only a few months, this limited time factor will probably influence the design of the foundation, and rightly so. If sensitive and complickted equipment is to be mounted on these foundations and the plant is to operate for several years, there should be a thorough study of foundations and a very careful design. A familiar problem is presented by the difficulty of operating a permanent plant originally designed for a few months&apos; work. The engineer must beware of these hazards and disassociate himself from them if he cannot prevail on the promoter to spend the proper amount for a thorough foundation study. Laws of certain provinces and states hold the engineer equally responsible with the contractor for any &apos;damage that may be caused to building through inadequate study-ignordnce of the facts is no excuse in the eyes of the law. Types of Soil: The engineer should be familiar with such terms as silt, clay, peat, and varved clay, as well as perpafrost, especially if he is to work in the far northern reaches of the country. He should also be familiar with soil attributes such as porosity, texture, consistency, permeability, compressibility, consolidation, and shearing resistance. The design of any foundation requires an accurate knowledge of the physical properties and location of the soils involved. Older textbooks on the subject outline various empirical methods to determine the carrying power of soil. Tables are given in reference books. The modern ehgineer should be wary of these modes of thinking. He should analyze his problem carefully, calculate to what depth of soil the loads may be transmitted, and then check the bearing value of all soils to that or greater depths. If the strata are water-carrying, he must determine the possibility of this water being accidentally re-

Jan 1, 1958

By Herbert Haas

CHEAP power is essential to large-scale mining and metallurgical operations, particularly where fine grinding of large tonnages has to be resorted to, as is the case with an increasing number of. mines treating disseminated copper ores, or low-grade gold ores, in the grinding of which considerable power is consumed. A comparison of the cost of generating power with Diesel engines and steam turbines and a brief discussion of the different factors governing the profitable use of either type of prime mover may be timely in view of the importance of. a cheap supply of power to the mining industry, and the prominence that has lately been given to Diesel engines in America. As many of our most important mines and largest producers of metals are located in sections where neither cheap coal nor water power is available, and the price of oil fuel is increased by long hauls, the Diesel. engine will. become a prime mover of increasing importance. This applies particularly to the Southwestern States, where an ample supply of cold water for condensing purposes is unusual and local climatological conditions interfere in securing the high vacua essential to high turbine efficiency. About 12 times as much water will be required for condensing purposes with steam turbines under general conditions as is needed for jacket-cooling of two-stroke, cycle Diesel engine; four-stroke cycle Diesel engines require only one-twentieth of the cooling water. Another condition favoring the use of Diesel engines is the high load factor at which most mine power plants operate. The influence of load factor on the cost of generating power is shown in Tables 1 and 2 and in Fig. 1.

Jan 7, 1916

By Noel Stearn

WHEN the Age of Machinery was suddenly thrust upon civilization about the beginning of the 19th century, an unprecedented demand for mineral resources sprang up. This demand brought about the rapid development of the known ore deposits and the discovery of such other deposits as could be encountered by energetic and canny prospectors. Thus in the countries now reasonably accessible nearly all orebodies have been located except those which are totally concealed even from the eyes and "senses" of experienced and expert prospectors. The high rate of exhaustion of known ore deposits and the necessity of looking farther and farther ahead for raw materials as a matter of insurance on the stupendous capital outlays involved in mining, development, and conversion operations, have resulted in exceptional activity in three different fields of effort. The first is purely geographic. Prospectors are now penetrating the few hitherto inaccessible regions in the hope of stumbling upon exposed ore deposits or locating visible indications of their presence. The second is chemical. Industrial chemists and metallurgists are seeking to facilitate the exploitation of lower grade ores or to find methods of recovering valuable metals from common substances. In the third field of effort lie the activities of the economic geologist and the mining engineer, who endeavor to locate concealed ore deposits which would remain hidden from the prospector no matter how expert or conscientious he might be. Obviously the task which such a man must face is both exacting and indefinite, and the tools which he has heretofore been permitted to bring to it are, for the most part, abstract-a knowledge of certain fundamental principles and processes involved in the origin, occurrence, structure, and distribution of deposits of natural resources and of the rocks which form the environments of those deposits; and a process. of reasoning by analogy supplemented by the use of the diamond drill, or such artificial exposure as -the test pit, trench, shaft, or tunnel.

Jan 1, 1928

By Jan M. Mutmansky

Main purpose of the research described is to apply the method of computer simulation to the process of tunneling by rapid excavation methods. Primary attention was focused on the materials handling subsystem because of its potential for improvement from a systems standpoint. A description is given of the computer model and a summary of some applications of the model for improving the rapid excavation process is included.

Jan 1, 1975

By Robert J. Brison

On the basis of experience accumulated during the completion of some 150 gold/silver process development projects, general guidelines are presented for developing the most cost effective process for a specific project. Steps involved in process development for lode ore deposits generally include a review of pertinent background information on the ore deposit, sample procurement and preparation, sample characterization, study of concentration possibilities, investigation of leaching and metal recovery methods, economic evaluation of alternative processes, optimization of the selected process, a pilot plant program if warranted, and finally, process design and feasibility studies. Each of these steps is discussed, with emphasis on the relation between technology and economics.

Jan 1, 1984

By J. M. Lohr

THE characteristics and uses of thermocouples of platinum and the platinum alloys being so well known, this paper will be confined to base-metal couples. During the past decade, there has developed a strong demand for thermocouples made of metals cheaper than the platinum alloys, and suitable for industrial heat measurements. Much research has been clone but only a very limited number of alloys have been found to possess the necessary characteristics for general technical use. In the development of thermocouple alloys it is necessary to consider the following points: The electromotive force and temperature relations; permanency or constancy; reproducibility; manufacturing difficulties; durability; and accuracy in use. The electromotive force developed by the thermocouple should increase with the rise of temperature according to some definite law. It is desirable that the electromotive force should vary directly with the temperature difference of its junctions, in other words, giving a curve linear or nearly so. It is also desirable that the resulting electromotive force be as large as possible for any given range of temperature, thereby insuring greater accuracy of readings.

Jan 9, 1919

By J. K. Furst

The reasons for manufacturing steel by the deplex process are, briefly…

Jan 1, 1915

By Richard E. McElvain, I. Cave

The selection of centrifugal pumps for mill discharge duty should be based on the total circuit concept. The practice of operating the mill circuit based on limitation of the pump can result in losses in one day which would offset the pump cost. Operating data from 25 grinding circuits have been reviewed and comparative results on added mill capacity have established advantages far beyond the less significant maintenance costs with increased circulating load and better cyclone operation. Mill discharge pumps should be selected on the following basis: i) Best available design for wear performance ii) Size to provide best economic life iii) Liner material best suited to circuit conditions Pump efficiency is a secondary consideration because power consumed by pumps is small compared to mill power input. Energy dissipated in mill pumps is contributing to comminution of ore.

Jan 1, 1982

By Sinha D. K.

As the main source of indigineous energy, coal has a big role to play in the development of national economy of India. Nationalization of the coal mining has brought the entire industry under the unit control of the Central Government following which an ambitious plan for increasing the coal production in the next few five year plans has been undertaken. In order to achieve best all round results, economy-mathematical models of Planning the total system, right from the highest to lowest hierarchial levels of decision making, have been proposed through a Global Model which is detailed in Local Models in stages right up to a mine. Optimum obtained by computer solution of the models would provide basis for objective decision making in the fields of selection of optimum plan for developing the industry, the coal fields and the mines with construction and/or reconstruction of mines, capacity optimization of enterprises and mines therein. Different types of Models and the optimization processes are presented.

Jan 1, 1977