Search Documents

By Shiou-Chuan Sun

THIS paper presents the design and operation of a frothmeter capable of measuring the frothing characteristics of pine oils and other frothing reagents. The experimental data show that the froth-ability of pine oil is governed by: 1—rate of aeration, 2—time of aeration, 3—height of liquid column, 4—chemical composition of pine oil, 5—pH value of solution, 6—temperature of solution, and 7—concentration of pine oil in solution. The effect of mineral particles on the behavior of froth also was studied, and the results can be found in a separate paper.' The results also show that the relative froth-abilities of pine oils in the frothmeter generally correlate with those in actual flotation, provided that other factors are kept constant. In addition to pine oils, the other well-established flotation frothers were tested, and the results are included. In this paper, compressed air frothing is the frothing process performed by means of purified compressed air, whereas sucked air frothing is the frothing process accomplished by purified air sucked into the glass cylinder by a vacuum system. The term vacuum frothing denotes that froth was formed by degassing of the air-saturated liquid under a closed vacuum system. Apparatus The frothmeter, shown in Fig. 1, is capable of re-producibly measuring the volume and persistence of froth as well as the volume of air bubbles entrapped in the liquid and is capable of being used for compressed air frothing, sucked air frothing, and vacuum frothing. Fig. la shows that for compressed air frothing, the apparatus consists of an airflow regulating system, 1-3; a purifying and drying system, 4-8; a standardized flowmeter to measure the rate of airflow from zero to 500 cc per sec, 9; and a graduated glass cylinder, 13; equipped with an air regulating stopcock, 10; an air chamber, 11; and a fritted glass disk to produce froth, 12. The fritted glass disk, 5 cm in diam and 0.3 cm thick, has an average pore diameter of 85 to 145 microns. The pyrex glass cylinder has a uniform ID of 5.588 cm and an effective height of 63 cm. The inside cross-sectional area of the glass cylinder was calculated to be 24.53 sq cm, or 3.8 sq in. For sucked air frothing, Fig. lb shows that the apparatus for compressed air frothing is used again, with the following modifications: 1—compressed air and its regulating system, 1-3, are eliminated; and 2—a vacuum system, 16, equipped with a vapor trap, 15, and a vacuum manometer, 17, is added. The vacuum system can be either a water aspirator or a laboratory vacuum pump. Any desired rate of airflow can be drawn into the glass cylinder, 13, by adjusting the opening of the air regulating stopcock, 10. The sucked air stream is cleaned by the purifying and drying system, 4-8, before entering the glass cylinder, 13. When this setup is used for vacuum frothing, the air regulating stopcock is closed. The frothmeter has been used for almost 3 years and has proved to give reproducible results, as illustrated in Table I. With a magnifying glass and suitable illumination, the frothmeter also can be used to study the attachment of air bubbles to coarse mineral particles.' Experimental Procedures Except where otherwise stated, the data presented were established by means of the compressed air method. The volume and persistence of froth were recorded respectively at the end of 4 and 6 min of aeration at a constant rate of airflow of 29.3 cc per sec, which is equivalent to 71.6 cc per sq cm per min, or 462.6 cc per sq in. per min. The aqueous solution for each test, containing 1000 cc of distilled water and 19.2 ± 0.5 mg frothing reagent, was adjusted to a pH of 6.9 0.2. The volume of froth is expressed as cubic centimeter per square centimeter and is equivalent to the height of the froth column (the distance between the bottom and the meniscus of the froth). The volume of froth was obtained by multiplying the height of froth by the cross-sectional area of the glass cylinder, 24.53 sq cm. Before each test, the glass cylinder, 13, was cleaned thoroughly with jets of tap water, ethyl alcohol, tap water, cleaning solution, tap water, and finally distilled water. The cylinder with stopcock,

Jan 1, 1953

By Shiou-Chuan Sun

THIS paper presents the design and operation of a frothmeter capable of measuring the frothing characteristics of pine oils and other frothing reagents. The experimental data show that the froth-ability of pine oil is governed by: 1—rate of aeration, 2—time of aeration, 3—height of liquid column, 4—chemical composition of pine oil, 5—pH value of solution, 6—temperature of solution, and 7—concentration of pine oil in solution. The effect of mineral particles on the behavior of froth also was studied, and the results can be found in a separate paper.' The results also show that the relative froth-abilities of pine oils in the frothmeter generally correlate with those in actual flotation, provided that other factors are kept constant. In addition to pine oils, the other well-established flotation frothers were tested, and the results are included. In this paper, compressed air frothing is the frothing process performed by means of purified compressed air, whereas sucked air frothing is the frothing process accomplished by purified air sucked into the glass cylinder by a vacuum system. The term vacuum frothing denotes that froth was formed by degassing of the air-saturated liquid under a closed vacuum system. Apparatus The frothmeter, shown in Fig. 1, is capable of re-producibly measuring the volume and persistence of froth as well as the volume of air bubbles entrapped in the liquid and is capable of being used for compressed air frothing, sucked air frothing, and vacuum frothing. Fig. la shows that for compressed air frothing, the apparatus consists of an airflow regulating system, 1-3; a purifying and drying system, 4-8; a standardized flowmeter to measure the rate of airflow from zero to 500 cc per sec, 9; and a graduated glass cylinder, 13; equipped with an air regulating stopcock, 10; an air chamber, 11; and a fritted glass disk to produce froth, 12. The fritted glass disk, 5 cm in diam and 0.3 cm thick, has an average pore diameter of 85 to 145 microns. The pyrex glass cylinder has a uniform ID of 5.588 cm and an effective height of 63 cm. The inside cross-sectional area of the glass cylinder was calculated to be 24.53 sq cm, or 3.8 sq in. For sucked air frothing, Fig. lb shows that the apparatus for compressed air frothing is used again, with the following modifications: 1—compressed air and its regulating system, 1-3, are eliminated; and 2—a vacuum system, 16, equipped with a vapor trap, 15, and a vacuum manometer, 17, is added. The vacuum system can be either a water aspirator or a laboratory vacuum pump. Any desired rate of airflow can be drawn into the glass cylinder, 13, by adjusting the opening of the air regulating stopcock, 10. The sucked air stream is cleaned by the purifying and drying system, 4-8, before entering the glass cylinder, 13. When this setup is used for vacuum frothing, the air regulating stopcock is closed. The frothmeter has been used for almost 3 years and has proved to give reproducible results, as illustrated in Table I. With a magnifying glass and suitable illumination, the frothmeter also can be used to study the attachment of air bubbles to coarse mineral particles.' Experimental Procedures Except where otherwise stated, the data presented were established by means of the compressed air method. The volume and persistence of froth were recorded respectively at the end of 4 and 6 min of aeration at a constant rate of airflow of 29.3 cc per sec, which is equivalent to 71.6 cc per sq cm per min, or 462.6 cc per sq in. per min. The aqueous solution for each test, containing 1000 cc of distilled water and 19.2 ± 0.5 mg frothing reagent, was adjusted to a pH of 6.9 0.2. The volume of froth is expressed as cubic centimeter per square centimeter and is equivalent to the height of the froth column (the distance between the bottom and the meniscus of the froth). The volume of froth was obtained by multiplying the height of froth by the cross-sectional area of the glass cylinder, 24.53 sq cm. Before each test, the glass cylinder, 13, was cleaned thoroughly with jets of tap water, ethyl alcohol, tap water, cleaning solution, tap water, and finally distilled water. The cylinder with stopcock,

Jan 1, 1953

By George J. Young

The recurrence of mine-fires in Nevada during the past decade is not only a matter of interest, but also one of considerable concern to engineers and mine-managers. The more important fires may be enumerated as follows: Forman Shaft fire, Gold Hill, April 21, 1903; shaft-house, machinery, and shaft destroyed; loss estimated at $50,000; cause unknown. Union Shaft fire, Virginia City, July 14, 1904; shaft-house, machinery,and shaft in part destroyed; loss estimated at $100,-000; cause of fire stated as the careless throwing of a match in the rope-house. Sutro Tunnel fire, Virginia City, Jan. 27, 1909; 700 ft. of tunnel-timbering destroyed, and direct damage of $10,000; cause " probably electric wires." Belcher Shaft fire, Gold Hill, Aug. 9, 1910; shaft-house destroyed, machinery ruined, and upper part of shaft damaged; damage, $25,000; no cause given. Belmont Mine fire, Tonopah, Feb. 23, 1911; fire started ill winze; 17 men killed. Giroux Mine fire, Kimberly, Aug. 23, 1911; fire originated in shaft-station from unknown cause; 7 men killed, and $34,-521 damage caused. (Note 1.—On June 11, 1912, some time after the present paper was written, a fire broke out in the pump-room on the 2475 station of the Ward shaft, Virginia City. This fire was caused by the short-circuiting and exploding of the starting-switch on No. 5 pump. The oil in the switch was scattered about and set fire to the timbers and lagging of the pump-room. The pump-man in charge notified the surface, and the electric current was shut off. A hose was then turned on the fire, but the dense smoke drove the attendant out. Inspection by the electrician and the shaft-foreman, equipped with oxygen-

Jan 1, 1913

AN extremely successful meeting, under the joint auspices of the Ohio Section and the Iron and Steel Committee, was held at Cleveland on April 19 and 20, about one-half of those in attendance being from the Cleveland district and the other half from a distance. The morning session on April 19, C. K. Leith presiding, was opened by the presentation of the ad-dress of which an excerpt is printed on the opposite page. In the subsequent discussion R. A. Allen pointed out that the meeting had not been called "to blow the lid off the tariff" since that is only one of the many problems connected with the wisest utilization of man-ganese, and it was the purpose of this meeting to con-sider all those interdependent problems. The purpose of the tariff was to develop an adequate domestic sup-ply, and that result had not been accomplished. An-other important problem, linked with the tariff, is the need for assuring, while we are at peace, an adequate war supply of manganese, and at present this country has no such policy. D. F. Hewett said that his 3-months' trip in Europe last summer had impressed him with the fact that England had once been in the position United States now is in, of being the principal world's producer of all the more important minerals and with a declining reserve had gone on a free-trade basis. No one pointed out that, with the exception of tin, the present relative position of England is due more to an increase in pro-duction in other countries, rather than to a decrease of domestic production. J. Sharshall Grasty referred to recent development work-in Virginia where of 30 per cent easily concen-trated manganese ore about 300,000 tons has been blocked out and possible and probable ore amounting to 700,000 tons more is indicated.

Jan 5, 1927

By Paul Hett

The much-heralded Deep Ruth operation of Kennecott Copper Corp., at Ruth, Nev., is scheduled to become a producer by 1957. Inaugurated as a project in 1951, production was originally scheduled to start in 1953, but excessive water hindered shaft sinking. A revised schedule called for output by 1955, but again plans had to be changed. This time the change was to permit mining of an orebody that would have otherwise been lost because of block caving methods planned for the main deposit. The new ore is within the cave limits of the larger orebody, above the first production level. Ore will start coming from this new source in 1956, a year ahead of the principal operation. (See NEWS, page 344.) There is little doubt that current economic conditions and unforeseen expenditures for early shaft development will make the Deep Ruth a high-cost producer. Yet, some of the drawbacks of the Kennecott operation may be mitigated by the possibility that additional exploration will increase the already assured 25 million tons of 0.83 pet copper ore. While Kennecott is missing out on the current high copper market and is thus left with a potentially narrowed profit, the predicted demand for copper has created an optimistic feeling. Its development is certain to enlarge known U. S. copper reserves and significantly extend the life of Kennecott's Nevada operations.

Jan 4, 1955

Jan 1, 1970

By Katherine Mather

This paper is an attempt to put together petrographic, physical, and chemical data about the large and varied group of rocks generally called limestones. Results of the properties of these rocks on their performance as concrete aggregates are discussed.

Jan 10, 1953

Jan 1, 1967

Jan 1, 1969

By T. Cantwell, N. C. Rasmussen, H. E. Hawkes

Beryl is a mineral that may be difficult to distinguish from quartz by casual field inspection. The easily recognized green color and hexagonal crystal form of coarse-grained beryl are by no means universal, even in beryl from pegmatitic deposits. If it occurred as a fine-grained accessory mineral in an igneous rock, it would almost certainly escape detection unless samples were submitted for petrographic or chemical analysis. There may be substantial deposits of some beryllium mineral, other than beryl, that has been overlooked because that mineral also closely resembles the common rock-forming minerals. A reliable and simple method of identifying beryllium minerals and determining the beryllium content of a rock would be helpful in exploration. This article describes preliminary experiments in applying nuclear reaction to the qualitative identification of beryl and to the semiquantitative determination of the beryllium content of rock samples.

Jan 9, 1959

By H. M. Beatty, T. L. Joseph, Gust Bitsianes

SUCCESSFUL blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blast- furnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO ? 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which C02 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature com- bustion of carbon above the tuyeres. Assuming that 1000 lb. of limestone is used per ton of pig iron, about 435 lb. of C02 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb. would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1942

Jan 1, 1966

By Oliver C. Ralston, James E. Norman

SEPARATION of minerals by froth flotation is rightly called an art. It can truthfully be said that no two ores separate in the same way. The difference in results obtained when natural and synthetic mixtures of minerals are separated is so great that such tests frequently have been worthless in attempting to select conditions in which a natural mixture will separate. With a few rare exceptions, the natural mixture is much more difficult to treat than a synthetic mixture, and a much poorer separation is obtained. Perhaps several experimenters have wondered why 10 or 20 per cent of a mineral being floated from an ore does not float and is different from the 90 or 80 per cent that is recovered. In experimental tests on pure sphalerite, observers1 have noted that varying amounts of sphaIerite may be froth-floated with pine oil alone, the amount recovered in the froth depending apparently upon the source of the sulphide. The only explanation of results such as these, barring insufficiency of frother or time of flotation, is that the surface of the mineral floated is different from that of the mineral depressed. This difference often has been found to be caused by natural contamination of mineral surfaces, apparently brought about by weathering and exposure to natural solutions. There is virtually no rock that is absolutely unweathered. One of the writers had an exceedingly instructive experience in 1931 while working with United Verde copper-zinc iron sulphide ore in Arizona. Nonselective flotation of chalcopyrite and sphalerite away from some of the pyrite was all that could be accomplished. All known depressants produced only slight effect. Sodium cyanide showed some effect, but so much had to be used that only a small amount of chalcopyrite could be

Jan 1, 1939

Beyond the industrial suburbs of Melbourne to the southeast are brown coal deposits just under the fertile soil of the Latrobe Valley. These deposits rank as one of the wonders of the world. The manner in which this resource is put to use is one of the great engineering accomplishments of our time and also a prime example of Australian elan. The brown coal, with over 60% water content, occurs in beds from 200 to 400 ft thick, under 50 ft of cover. Fifty thousand tons of coal per day move in a nearly continuous stream from mining face to boilers. The power plants supply two thirds of the State of Victoria's requirements, about 800 megawatts. Surge capacity between mine and power plant is sufficient for 12 hr steaming time! Victorian brown coals have been known since the middle of the 19th century. However, it took a strike of bituminous coal miners in 1915 to bring brown coal permanently into the picture as a fuel for power generation. In Australia, power generation is a State function. The great development of brown coals has been under the State Electricity Commission of Victoria.

Jan 10, 1964

Jan 1, 1965

By R. C. Allen, Ralph Arnold

The writers have no new system and no new principle of taxation to propose. The general subject of taxation is as old as governments are and as familiar to taxpaying Americans as the general thesis on the inalienable rights of man. We believe, therefore, following the committee of the National Tax Association, that improvement in the general conditions of taxation, including mine taxation, maybe brought about mainly through a better adjustment of known and tried principles and methods of taxing to modern complex forms of property and income, and that not much is to be expected from abandonment of experience for new ways and means, methods and principles, should anything new be discovered, which in our opinion is very doubtful. The committee referred to has constructed the general framework of its Model System of State and Local Taxation1 on familiar forms of taxing, by eliminating some that ' have proved bad, suggesting improvements in others, and adopting the best, leaving plenty of room for the accommodation of the general plan to the varying conditions of taxation in the several states. Unfortunately, the taxation of mines is dismissed by the committee with the statement that the subject has been reassigned for further investigation and report by a special sub-committee, frankly recognizing that the peculiar difficulties of this phase of the subject require special study and investigation. Much may be hoped for from the labor of this sub-committee if the problem is approached from the viewpoint of recommendations already published. In this paper, the writers state their opinion on some of the broader aspects of mine taxation with too little attention to the grounds on which they rest. Contrary to inclination space requirements compel them to resort to summary statements without adequate discussion for a satisfactory presentation of the whole subject. All they can do is to qualify the witnesses and record the testimony. The senior writer was introduced to the practical aspects of the subject of this paper in 1913, when, as State Geologist of Michigan, he was

Jan 1, 1920

By Chung Yu Wang

STUDY of two recent papers and a recent book leads one to raise anew the question-Why are certain regions of the earth more mineralized than others?

Jan 5, 1953