Search Documents

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Trustees, lnc. When Mr. Carnegie made his gift which made possible a home for the engineering societies, a separate corporation was organized to act as a holding company and to manage the common property. This was long known as the United Engineering Society, but the name has now been changed to one which more nearly reflects the real function of the corporation. It holds title to the Engineering Societies Building and to various funds placed in its charge and is managed by a Board of Trustees, of which three are chosen by each of the four societies, American Institute of Mining and Metallurgical Engineers, American Society of Mechanical Engineers, American Institute of Electrical Engineers and American Society of Civil Engineers, which have equal and undivided interests in. the property. The land and building cost two million dollars. During the year 1934, the Constitution and Bylaws

Jan 1, 1938

By P. R. Celmer, Leonard R. Weisberg

THE principle of fractional crystallization has been successfully used to prepare high-purity (99.999 pct) Ga. Hoffman and Scribnerl removed single crystals of gallium solidifying in a gallium melt, while Zimmerman2 grew single crystals from the melt by the Kyropolous technique. In contrast, attempts at purifying gallium by zone refining have been less successful. ichards, reported that despite the passage of 40 zones through a gallium ingot, there still remained 5 to 70 ppm each of Cu, Fe, Ca, Mg, Si, Al, and Ag. Previously, Detwiler and Fox4 detected only one impurity, Pb, segregating in zone-refined ingots. These surprising results prompted an investigation of the factors controlling impurity segregation in gallium. Possible reasons for this were insufficient diffusion of impurities in the melt; recontamination of the melt by its oxide film which is not affected by the passage of the zone; reaction of gallium with the boat; sudden freezing of gallium following supercooling, especially since gallium easily supercools to and trapping of impurities at grain boundaries. Impurity segregation tests were carried out by directionally freezing gallium using the Bridgman rnethd, modified in that the molten gallium is lowered out of a furnace into a slush of dry ice and trichloroethylene, thus minimizing supercooling. Since the gallium is contained vertically, the oxide film is in contact only with the tail end of the melt. It was found that Teflon makes an excellent crucible for gallium since it is quite pure, non-reactive, translucent, flexible, machinable, and is not wet by gallium. The gallium crystals could be grown at various speeds, and the melt could be vigorously stirred by a Teflon rod moving through the gallium in a vertical reciprocating fashion. Single crystals could be grown by placing a solid Teflon plug at the bottom of the melt drilled out in such a way to cause the solidifying gallium to follow a winding path. Thus, even if many crystals are originally nucleated, only one grain will predominate. The grain structure of the gallium crystals was revealed by an etchant composed of equal volumes of HC1, HNO3 and HF, diluted with water to half strength. Emission spectrographic analyses were carried out on samples removed from the front and tail ends of the resulting gallium ingots. Typical results of this study are summarized in Table I. The rate of freezing in all three cases was about 1 in. per hr. It can be seen that even though stirring of the melt does help, it is even more important to grow a single crystal of Ga in order to obtain good segregation of impurities. The effect of crys-tallinity on the segregation of impurities was previously observed6 in the directional freezing of germanium; however, in this case, the effect was much less pronounced. This dependence of impurity segregation on the crystalline perfection of Ga may be related to its thermal conductivity which is the most anisotropic of all metals.7 The anisotropic thermal conductivity can cause the solid-liquid interface to be nonuniform, thus leading to trapping of impurities during freeing, and therefore reduced segregation. In conclusion, it is indicated that zone refining of gallium would be more successful if seeding and similar precautions are taken to insure single crystal growth. The authors are indebted to Mr. H. H. Whitaker for the spectrographic analyses and to Drs. B. Abeles and F. D. Rosi for helpful advice and encouragement throughout the course of this work. This research was supported by the Electronics Research Directorate, Air Research and Development Command, under Contract No. AF33(616)-5029. REFERENCES 'J. 1. IToffmon and B. T. Scribrer: I. Research h'atl. Bur. Standards, 1935, "01. 15, p. 205. 'W. Zirnmerman: Science, 1954, vol. 119, p. 41. %J. L. Richards: Nature, 1956, vol. 117, p. 182. 'D. P. Detwiler and W. M. Fox: I. Metals, 1955, "01. 7, p. 205. 5P. W. Bridgman, Proc. Am. ilcod. Sci., 1925, vul. 60, pp. 305,385,423. "S. L1. Christian: private c ommuni cation. 'K. W. Powell: roy. Sac., 1951, vol. 209, p. 525. 'W. G. Pfann: Zone Re fining, p. 20. John Wiley and Sons, Inc., New York, L058.

Jan 1, 1962

By D. M. Francois-Bongarcon

The idea of parameterizing reserves has only been formalized and scientifically applied for a few years. Its most fully developed application, that of open pits, has been operational only since 1976. Two new versions which have just been issued provide a complete solution to the problem and also a powerful tool for mine planning, and they open up a new field of investigation. This paper describes the basic principles for parameterizing reserves, their application for open-pit mines, the algorithm used, the physical interpretation of the results obtained, their economic use as well as the first prospects offered by a complete parameterization in tm of (I. ti), or of the metal price.

Jan 1, 1984

I have the honor to submit herewith the report of the Secretary for the year 1915 showing the principal activities of the Institute: Meetings.-The 110th Meeting, including the Annual Business Meeting, was held in New York City, Feb. 15 to 17, 1915. The full report of this meeting is given in Volume LI of the Transactions. The number of papers presented was 53, and the attendance was 357 members and guests. The 111th Meeting was held in San Francisco, Cal., Sept. 16 to 19, 1915. Sixty-eight technical papers were presented, and the attendance was over 400 members and guests. The full report of this meeting is given in the Bulletin for December, 1915. Local Section.-A new, strong Local Section of the Institute, with head-quarters in Arizona and known as the Arizona Section, was formed during 1915. Affiliated Student Societies.-Three new Affiliated ,Student Societies were recognized in 1915 consisting of the Pick and. Hammer Club of the University of Oklahoma, Mining and Metallurgical Club of the Univer-

Jan 2, 1916

By W. M. Bertholf

IN 1945 tests were made in the coal washery of the Colorado Fuel and Iron Corporation, at Pueblo, Colo., to determine the value of the Humphreys spiral. So far we have demonstrated that it is of definite value to us in rewashing a portion of our table middlings; and we are fairly certain that this is not necessarily the only place in which it can be used to advantage. Because of manpower and material shortages, experimental work has been discontinued for the present. Three of the spirals are being installed for use in rewashing the middlings, and testing and experimental work will proceed when this installation is completed. All evidence secured so far points to the fact that the spiral can make an effective separation of heavy material below 8-mesh; but that it is ineffective in removing larger, heavy material. This, of course, will limit its use to fine coal or a classified feed containing no heavy material larger than 8-mesh. In considering the results of our tests, it should be noted that the feed was our table middling, and that any real separation of this material is a "moral victory," as there is little material that could be properly called coal and practically no heavy rock, the consequence being that previous attempts to clean the middlings have not been at all successful. Several articles dealing with the spiral and its use in treating heavy minerals have already been published,1 but for the benefit of those who have not seen these we include a brief description of the spiral and of the way it operates, taken from Bulletin 4 of The Humphreys Investment Co.: The Humphreys Spiral Concentrator consists of a spiral conduit of modified semicircular cross section. Ore pulp is fed to the top and, as it flows downward, the heavier particles concentrate in a band along the inner side of the pulp stream (Fig. I). Outlets for removal of products are located at the lowest points in the cross section of the conduit. Wash water, added at the inner edge of the stream, flows outwardly across the concentrate band. The width of concentrate band removed at the outlets is controlled by adjustable splitters. Concentrate is usually removed from the upper portion of the spiral and middling from the lower portion. Tailing is discharged from the lower end. Tests are usually made in closed circuit, since this provides a maximum of information with a minimum amount of sample. Fig. 2 shows the spiral set up for closed-circuit testing, and gives a good idea of the general arrangement of such an installation. The small cyclone separator is used to provide clean wash water without introducing additional water into the circuit.

Jan 1, 1946

By D. W. Frommer

Processing nonmagnetic taconites by selective flocculation-desliming and flotation requires large volumes of water. If impounded without treatment the effluents from these processes require excessively large areas for containment. Experiments conducted in the Bureau of Mines 900-lb-per hr pilot plant at the Twin Cities Metallurgy Research Center indicates that approximately 85% of the water needed to process Michigan nonmagnetic taconite could be reclaimed from the process itself. Water was reclaimed by the controlled addition of lime, sodium carbonate, and synthetic flocculant. As a result, turbidities were reduced to ?1000 ppm equivalent SiO2, while a Ca ion content of ?16 ppm was maintained in the finished effluent. Good-quality flotation concentrates were obtained with reclaimed water and, by means of some indirect comparisons, it can be concluded that the reuse of the water permits a savings of almost 2.0 lb per ton of NaOH, and probably as much as 0.25 lb per ton of fatty acid for total savings of 7.8-10.3 cents per ton of feed. These savings are nearly offset by an estimated chemical cost of 9.3[c] per ton for water treatment.

Jan 1, 1970

By A. Kenneth Schellinger, O. Cutler Shepard

Overgrinding, Or the breaking of ore particles into sizes smaller than required for liberation, is a first-magnitude problem in grinding for concentration processes. The conventional ball mill-classifier circuit used in commercial grinding produces mineral particles that are all ground to pass an upper size limit, while the proportion of very fine sizes, or slimes, is uncon rolled. Calculations based on measurements made in commercial plants which were grinding ore for flotation concentration indicate that about go pct of the energy used in grinding is consumed in useless overgrinding.1 In addition to accounting for the consumption of a large amount of energy, over-grinding is detrimental to the flotation process. Overground slime coats larger partitles and inhibits selective action by the flotation reagents on particles which by themselves could be separated very well. A further difficulty is that extremely finely ground minerals do not respond satisfactorily to flotation-collecting reagents, and both selection and recovery decrease markedly with particles finer than 5 to 10 microns.2 conventional classifier-ball mill circuits inherently tend to overgrind the valuable minerals more than the gangue minerals because most valuable minerals are of higher density and are softer and more friable than the gangue minerals. The rem- edy to this situation would seem to be a separating mechanism which would separate free valuable mineral particles regardless of size and density considerations and a mechanism which would operate in the grinding mill so that valuable mineral grains would be removed from the grinding machine as soon as they are freed. A consideration of these ideas led the authors to the conception of a simultaneous grinding and flotation mechanism. So far as the authors are aware, such a machine has never been tried, even on a laboratory scale. Development oF Apparatus and Experimental Method Apparatus development went through several stages before a really workable machine was devised. Work was started with a large cast-iron mortar 7½ in. in diameter and 8 in- deep. A cast-iron disk Was mounted on the end of a vertical shaft SO that it fitted loosely into the bottom of the mortar. On top of the disk four radial cleats ¼ in. high were bolted to agitate the ball charge as the disk, or impeller, rotated. The vertical shaft was driven at 100 rpm by a mechanism improvised from an old coffee-mill type of grinder. A hole was drilled into the bottom of the mortar through which compressed air was introduced for frothing. In operation, more charges of Ore which had been crushed to pass an 8-mesh screen were placed in the bowl along with water and suitable reagents. The impeller was then started and the compressed air turned On so that the ore was ground while being exposed to air bubbles. Mineralized froth was

Jan 1, 1949

Duval Corporation, the owners of the Sierrita, Esperanza, and Mineral Park copper operations in Arizona, first acquired the mineral rights to their Battle Mountain, Lander County, Nevada, property in 1962. Development of the mine commenced in mid - 1965, and the copper operation began at the end of 1968. The ore, a mixture of chalcocite and chalcopyrite, was milled and floated at a rate of 3, 175 mtpd (3,500 stpd). Because of low copper grade and price, the plant was shut down after about ten years of operation. Attention was then turned to an adjacent low-grade precious metal ore body which contained 2.74 g Au and 3.4 g Ag per mt (0.08 oz Au and 0.10 oz Ag) and minor amounts of copper. Test work revealed recovery by Carbon-In- Pulp treatment would amount to approximately 2.8 mt (90,000 oz) each of gold and silver per year. A rapid engineering and construction schedule resulted in the world's largest, as of late 1980, Carbon-In- Pulp plant being put on-stream in January 1979, with a capacity of 2.720 mtpd (3,000 stpd). Fortunately, the original crushing and grinding plant with all its infra structure was available, and the only modification needed was the addition of a gravity circuit to remove coarse free gold ahead of Carbon- In-Pulp treatment. One of the four primary 500 mm (20 in.) cyclone underflows in the primary ball mill circuit is directed to a secondary ball mill where its product is again cycloned. The cyclone underflow is screened at 3,360 microns (6 mesh) with the undersize being treated on two Pan American 1.07 m by 2. 14 m (42 in. by 84 in.) jigs. Hutch product is further concentrated on two Wilfley tables, a magnetic separator, and on a third Wilfley table where approximately 930 g (30 oz) of gold are recovered each day for amalgamation, retorting, and smelting. Returning to the grinding circuit, the final cyclone overflow is sent to the original plant tailings thickener to obtain proper pulp density for Carbon-In-Pulp treatment. Thickener underflow, at about 40% solids, is then conditioned with air and lime in a series of two 8.5 m by 9.75 m (28 ft by 32 ft) 15O cone bottom Pachucas for oxidation of pyrrhotite. The pulp is then split into two streams for cyanidation for 48 hours in two lines of eight Pachucas of the same size. Pulp is transferred from tank to tank by auxiliary air lifts. Cyanided pulp is then sent to a series of six C. I. P. mechanically agitated tanks with one hour retention in each tank. Originally these

Jan 1, 1981

By Don B. Carson, Donald L. Katz

NATURAL gases under pressure form crystal-line hydrates with water. Experimental data are reported on four-phase equilibrium for the methane-propane-water, methane-pentane-water, and methane-hexane-water systems. Temperatures and pressures for equilibrium between gas, water-rich liquid, hydrocarbonrich liquid, and hydrate were measured, as well as the percentages of methane and propane in the hydrate. The data indicate that natural gas hydrate behaves as a solid solution and that pentanes and heavier hydrocarbons do not enter into the solid phase. Vapor-solid equilibrium constants are presented that permit the approximation of the conditions for hydrate formation, from the composition of a gas. INTRODUCTION Natural gas hydrates have been the object of considerable research in recent years, because of the trouble they have caused in the natural-gas and natural gasoline industries. Natural gas hydrates are white crystalline compounds of water and gas, which, under pressure, exist at temperatures considerably above the freezing point of water. Because of the relatively high temperatures at which the hydrates exist, they become a nuisance in high-pressure gas operations where water is present, since their formation causes partial or complete plugging of valves and pipes. From a practical standpoint, the trouble incident to hydrate formation has been solved by dehydration of the gas before it enters the plant or pipe line, or by other remedial measures. Extensive work on gas hydrates in the latter part of the nineteenth century, by Villard1 and others, gave data on methane hydrate and on ethane hydrate. Schroeder summarized these theoretical studies.2 Hammerschmidt3 introduced the information on gas hydrates to the gas industry and Deaton and Frost4-6 gathered a considerable number of data on the behavior of natural gas hydrates. Recent papers7,8 have extended both the data and the theory of these hydrates. At present, data are available on temperatures and pressures of hydrate formation for pure methane, ethane, propane, n-butane, methane-ethane mixtures, methane-propane mixtures, methane-butane mixtures, and some 15 natural gases, all in the presence of excess water. However, up to the present time no method has been available for predicting the temperature at given pressures or the pressure at given temperatures at which natural gases will form hydrates if saturated with water. This paper pre¬sents data on the methane-propane-water, methane-pentane-water and methane-hexane water systems in four phases, one of which is the hydrate. The application of the phase rule to the methane-propane-water data proves that hydrates behave as solid solutions. The data of this paper and those in the literature were used to develop vapor-solid equilibrium constants,8 which permit prediction of conditions of hydrate formation from the analysis of a natural gas.

Jan 1, 1941

By W. M. Bertholf

In 1945 tests were made in the coal washery of the Colorado Fuel and Iron Corporation, at Pueblo, Colo., to determine the value of the Humphreys spiral. So far we have demonstrated that it is of definite value to us in rewashing a portion of our table middlings; and we are fairly certain that this is not necessarily the only place in which it can be used to advantage. Because of manpower and material shortages, experimental work has been discontinued for the present. Three of the spirals are being installed for use in rewashing the middlings, and testing and experimental work will proceed when this installation is completed. All evidence secured so far points to the fact that the spiral call make an effective separation of heavy material below 8-mesh; but that it is ineffective in removing larger, heavy material. This, of course, will limit its use to fine coal or a classified feed containing no heavy material larger than 8-mesh. In considering the results of our tests, it should be noted that the feed was our table middling, and that any real separation of this material is a "moral victory)" as there is little material that could be properly called coal and practically no heavy rock, the consequence being that previous attempts to clean the middlings have not been at all successful. Several articles dealing with the spiral and its use in treating heavy minerals have already been published,' but for the benefit of those who have not seen these we include a brief description of the spiral and of the way it operates, taken from Bulletin 4 of The Humphreys Investment Co.: The Humphreys Spiral Concentrator consists of a spiral conduit of modified semicircular cross section. Ore pulp is fed to the top and, as it flows downward, the heavier particles concentrate in a band along the inner side of the pulp stream (Fig. I). Outlets for removal of products are located at the lowest points in the cross section of the conduit. Wash water, added at the inner edge of the stream, flows outwardly across the concentrate band. The width of concentrate band removed at the outlets is controlled by adjustable splitters. Concentrate is usually removed from the upper portion of the spiral and middling from the lower portion. Tailing is discharged from the lower end. Tests are usually made in closed circuit, since this provides a maximum of information with a minimum amount of sample. Fig. 2 shows the spiral set up for closed-circuit testing, and gives a good idea of the general arrangement of such an installation. The small cyclone separator is used to provide clean wash water without introducing additional water into the circuit.

Jan 1, 1947

By W. M. Bertholf

In 1945 tests were made in the coal washery of the Colorado Fuel and Iron Corporation, at Pueblo, Colo., to determine the value of the Humphreys spiral. So far we have demonstrated that it is of definite value to us in rewashing a portion of our table middlings; and we are fairly certain that this is not necessarily the only place in which it can be used to advantage. Because of manpower and material shortages, experimental work has been discontinued for the present. Three of the spirals are being installed for use in rewashing the middlings, and testing and experimental work will proceed when this installation is completed. All evidence secured so far points to the fact that the spiral call make an effective separation of heavy material below 8-mesh; but that it is ineffective in removing larger, heavy material. This, of course, will limit its use to fine coal or a classified feed containing no heavy material larger than 8-mesh. In considering the results of our tests, it should be noted that the feed was our table middling, and that any real separation of this material is a "moral victory)" as there is little material that could be properly called coal and practically no heavy rock, the consequence being that previous attempts to clean the middlings have not been at all successful. Several articles dealing with the spiral and its use in treating heavy minerals have already been published,' but for the benefit of those who have not seen these we include a brief description of the spiral and of the way it operates, taken from Bulletin 4 of The Humphreys Investment Co.: The Humphreys Spiral Concentrator consists of a spiral conduit of modified semicircular cross section. Ore pulp is fed to the top and, as it flows downward, the heavier particles concentrate in a band along the inner side of the pulp stream (Fig. I). Outlets for removal of products are located at the lowest points in the cross section of the conduit. Wash water, added at the inner edge of the stream, flows outwardly across the concentrate band. The width of concentrate band removed at the outlets is controlled by adjustable splitters. Concentrate is usually removed from the upper portion of the spiral and middling from the lower portion. Tailing is discharged from the lower end. Tests are usually made in closed circuit, since this provides a maximum of information with a minimum amount of sample. Fig. 2 shows the spiral set up for closed-circuit testing, and gives a good idea of the general arrangement of such an installation. The small cyclone separator is used to provide clean wash water without introducing additional water into the circuit.

Jan 1, 1947

By H. C. Kenny

THE annealing or softening temperature of cold-worked copper is appreciably increased by almost unbelievably small amounts of silver. As indicated by some data in this paper, the softening temperature of high-conductivity, tough-pitch copper may be increased from 200° to 350° C. by the addition of only 15 oz. per ton (0.052 per cent) of that element. Because it has this higher annealing temperature as compared with the silver-free metal, silver-bearing copper finds considerable use in industry. For example, when hard-rolled copper is used in operations that involve soldering or tinning, silver-bearing copper insures against loss of strength, whereas silver-free copper becomes "dead soft." Yet-though several investigators, beginning with Caesar and Gerner1 in 1916, have shown that small amounts of silver do definitely raise the softening temperature of copper-data are lacking on the problem: What is the specific influence of different amounts of silver on this tem-perature? It was to help in filling this gap in the knowledge of what might be termed "alloy coppers" that the data given herein were obtained. The softening of cold-worked copper depends, of course, on a number of factors, of which the composition of the material is only one. Other highly important factors are the degree to which the material is cold-worked and the time it-is held at the annealing temperature. The method of cold working and the grain size of the metal produced are also signifi-cant. All these variables were taken into account in the investigation reported here, and the influence of silver on the electrical conductivity and on the working was also considered.

Jan 1, 1934

By D. B. Carson, D. L. Katz

Natural gases under pressure form crystalline hydrates with water. Experimental data are reported on four-phase equilibrium for the methane-propane-water, methanc-pentane-water, and methane-hexane-water systems. Temperatures and pressures for equilibrium between gas, water-rich liquid, hydrocarbon-rich liquid, and hydrate were measured, as well as the percentages of methane and propane in the hydrate. The data indicate that natural gas hydrate behaves as a solid solution and that pentanes and heavier hydrocarbons do not enter into the solid phase. Vapor-solid equilibrium constants are presented that permit the approximation of the conditions for hydrate formation, from the composition of a gas. Introduction Natural gas hydrates have been the object of considerable research in recent years, because of the trouble they have caused in the natural-gas and natural-gasoline industries. Natural gas hydrates are white crystalline compounds of water and gas, which, under pressure, exist at temperatures considerably above the freezing point of water. Because of the relatively high temperatures at which the hydrates exist, they become a nuisance in high-pressure gas operations where water is present, since their formation causes partial or complete plugging of valves and pipes. From a practical standpoint, the trouble incident to hydrate formation has been solved by dehydration of the gas before it enters the plant or pipe line, or by other remedial measures. Extensive work on gas hydrates in the latter part of the nineteenth century, by Villardl and others, gave data on methane hydrate and on ethane hydrate. Schroeder summarized these theoretical studies2 Hammerschmidt3 introduced the information on gas hydrates to the gas industry and Dcaton and Frost4-6 gathered a considerable number of data on the behavior of natural gas hydrates. Recent papers7,8 have extended both the data and the theory of these hydrates. At present, data are available on tem-peraturcs and pressures of hydrate forma. tion for pure methane, ethane, propane, n-butane, methane-ethane mixtures, meth-ane-propane mixtures, methane-butane mixtures, and some Is natural gases, all- in the Presence of excess water. However, up to the Present time no method has been available for predicting the temperature at given pressures or the pressure at given at at which natural gases will form hydrates if hydrates with water. 'This Paper Presents data on the methane-propane-water, methane-pentane-water and methane-hex-""e water systems in four phases, one of which is the hydrate. he application of the phase rule to the methane-~ro~ane-water data Proves that hydrates behave as solid solutions. The data of this paper and those in the literature were used to develop vapor-solid. equilibrium constants,8 which permit prediction of conditions of hydrate formation from the analysis of a natural gas.

Jan 1, 1942

By D. B. Carson, D. L. Katz

Natural gases under pressure form crystalline hydrates with water. Experimental data are reported on four-phase equilibrium for the methane-propane-water, methanc-pentane-water, and methane-hexane-water systems. Temperatures and pressures for equilibrium between gas, water-rich liquid, hydrocarbon-rich liquid, and hydrate were measured, as well as the percentages of methane and propane in the hydrate. The data indicate that natural gas hydrate behaves as a solid solution and that pentanes and heavier hydrocarbons do not enter into the solid phase. Vapor-solid equilibrium constants are presented that permit the approximation of the conditions for hydrate formation, from the composition of a gas. Introduction Natural gas hydrates have been the object of considerable research in recent years, because of the trouble they have caused in the natural-gas and natural-gasoline industries. Natural gas hydrates are white crystalline compounds of water and gas, which, under pressure, exist at temperatures considerably above the freezing point of water. Because of the relatively high temperatures at which the hydrates exist, they become a nuisance in high-pressure gas operations where water is present, since their formation causes partial or complete plugging of valves and pipes. From a practical standpoint, the trouble incident to hydrate formation has been solved by dehydration of the gas before it enters the plant or pipe line, or by other remedial measures. Extensive work on gas hydrates in the latter part of the nineteenth century, by Villardl and others, gave data on methane hydrate and on ethane hydrate. Schroeder summarized these theoretical studies2 Hammerschmidt3 introduced the information on gas hydrates to the gas industry and Dcaton and Frost4-6 gathered a considerable number of data on the behavior of natural gas hydrates. Recent papers7,8 have extended both the data and the theory of these hydrates. At present, data are available on tem-peraturcs and pressures of hydrate forma. tion for pure methane, ethane, propane, n-butane, methane-ethane mixtures, meth-ane-propane mixtures, methane-butane mixtures, and some Is natural gases, all- in the Presence of excess water. However, up to the Present time no method has been available for predicting the temperature at given pressures or the pressure at given at at which natural gases will form hydrates if hydrates with water. 'This Paper Presents data on the methane-propane-water, methane-pentane-water and methane-hex-""e water systems in four phases, one of which is the hydrate. he application of the phase rule to the methane-~ro~ane-water data Proves that hydrates behave as solid solutions. The data of this paper and those in the literature were used to develop vapor-solid. equilibrium constants,8 which permit prediction of conditions of hydrate formation from the analysis of a natural gas.

Jan 1, 1942

By A. Kenneth Schellinger, O. Cutler Shepard

INTRODUCTION OVERGRINDING, or the breaking of ore particles into sizes smaller than required for liberation, is a first-magnitude problem in grinding for concentration processes. The conventional ball mill-classifier circuit used in commercial grinding produces mineral particles that are all ground to pass an upper size limit, while the proportion of very fine sizes, or slimes, is uncontrolled. Calculations based on measurements made in commercial plants which were grinding ore for flotation concentration indicate that about 90 pct of the energy used in grinding is consumed in useless overgrinding.1 In addition to accounting for the consumption of a large amount of energy, overgrinding is detrimental to the flotation process. Overground slime coats larger particles and inhibits selective action by the flotation reagents on particles which by themselves could be separated very well. A further difficulty is that extremely finely ground minerals do not respond satisfactorily to flotation-collecting reagents, and both selection and recovery decrease markedly with particles finer than 5 to 10 microns.2 Conventional classifier-ball mill circuits inherently tend to overgrind the valuable minerals more than the gangue minerals because most valuable minerals are of higher density and are softer and more friable than the gangue minerals. The remedy to this situation would seem to be a separating mechanism which would separate free valuable mineral particles regardless of size and density considerations and a mechanism which would operate in the grinding mill so that valuable mineral grains would be removed from the grinding machine as soon as they are freed. A consideration of these ideas led the authors to the conception of a simultaneous grinding and flotation mechanism. So far as the authors are aware, such a machine has never been tried, even on a laboratory scale. DEVELOPMENT OF APPARATUS AND EXPERIMENTAL METHOD Apparatus development went through several stages before a really workable machine was devised. Work was started with a large cast-iron mortar 7 ½ in. in diameter and 8 in. deep. A cast-iron disk was mounted on the end of a vertical shaft so that it fitted loosely into the bottom of the mortar. On top of the disk four radial cleats ¼ in. high were bolted to agitate the ball charge as the disk, or impeller, rotated. The vertical shaft was driven at 100 rpm by a mechanism improvised from an old coffeemill type of grinder. A hole was drilled into the bottom of the mortar through which compressed air was introduced for frothing. In operation, weighed charges of ore which had been crushed to pass an 8-mesh screen were placed in the bowl along with water and suitable reagents. The impeller was then started and the compressed air turned on so that the ore was ground while being exposed to air bubbles. Mineralized froth was

Jan 1, 1947

By O. N. Wampler

UNDERGROUND lighting in the zinc mines of the Tri-State district can be separated into four di-visions. 1. Foot of shaft. 2. Pumps, fans. incline hoists and other stationary machinery. 3. Haulage ways. 4. Headings and stopes. One of the main improvements in lighting around the bottom of the shaft is in the use of skidoo flash lights, which have replaced the old electric skidoo bells. These bells were used as signals from the hoisterman to the tub hooker. In the event that a can bumped the side of shaft or a rock spilled from the can when dumping; the hoisterman rang the skidoo bells as a signal for all to leave the vicinity of the shaft bottom on a dead run. These bells were much better than no signal at all, but many of them were often out of order; the worst feature being that when out of order this fact was not immediately indicated. The electric flash-light signals work on the opposite principle and are burning at all times except when the hoisterman breaks the circuit when signaling danger. Therefore should a break or short occur in this arrangement, the shaft bottom is immediately thrown in darkness. Since the reaction from the eye is quicker than from ear, there is a slight saving of time- to the men escaping from the point of danger. Even this brief period of time may save a life. One other, point, to be emphasized, is that all lights near the shaft bottom should be on the signal circuit so that the entire area is momentarily darkened. I. have inspected mines where only one or two lights are used as signals, with the remaining lights around the shaft on another fixed circuit. In this case the flashing of the signal lights is almost drowned out by the stationary lights. These flash signals must be as startling as possible, which can only be done by flash-ing all the lights.

Jan 6, 1928

For the benefit of those of our members who are considerable holder; of securities, but owing to their isolated situations are not in close touch with the metropolitan market and current quotations, we are publishing two very interesting graphs, showing the course of the bond and stock markets in New York over a long period. These graphs are-fui?riished through the courtesy of the financial department of the New York Tribune.

Jan 8, 1919

By D. C. Hilty

C. E. SIMS*—This is a most interesting and important paper. It is important from two standpoints. First, it has as-spects of being highly accurate and therefore extremely useful to the operating man in showing how far he can go in oxidizing carbon from a steel bath while retaining chromium and the effect of temperature on this limit. Fig 5 is undoubtedly the highlight of the paper, and in checking it against available data, it seems capable of predicting actual results. The other important aspect is the apparently significant fact that reactions within a steel bath, such as between carbon and an oxide, are homogeneous reactions which do not require equilibrium with an external phase. In this case, it seems obvious that the reaction and the equilibrium established were between dissolved carbon (or carbide) and dissolved CrO. The classic reaction which requires equilibrium with solid Cr2O3, did not fit the data. It was recognition of this principle that made Fig 5 possible. G. R. FITTERER*—It might be in assuming the CrO is dissolved in the metal that you are actually approaching the correct factor for activity. If that is true and if the percentages that were used represent an equilibrium constant, this would mean, in effect, that the minimum temperature at which chromium would be reduced by an equivalent percentage of carbon would be about 2400°F from your equation. I believe that is in line with my experience particularly if you deal only with low percentages. J. CHIPMAN†—The author in discussing the equilibrium of the reaction offers two choices of explanation. One postulates an effect of chromium on the activity coefficient of carbon; it would require perhaps more data than are available to us at the present time to test this thoroughly. The other postulate which he offers is a reaction with CrO. This explanation is consistent with physical and chemical principles provided that a solid phase CrO is present, and that is essentially what he is postulating. If that oxide were present one would expect and, I think, almost require the kind of results that he obtained. The weakness of that postulate lies in the lack of confirmatory evidence regarding the presence of solid CrO as such. This should offer an interesting subject for further study. It seems a pity that the theoretical arguments revolving around CrO should have obscured for a moment the very real excellence of this paper. E. CARTER*—I think there is a problem that presents itself in practical application where the metal temperature is from 3200 to 3300 and the temperature desired in pouring is considerably less. B. M. LARSEN†—I get the impression from some of the work that was done earlier that there is probably a localized zone of high temperature at the slag metal interface which effects the removal of the carbon. Without that I wonder if the effect is possible to have a localized superheat and an equilibrium there favorable to low carbon content and

Jan 1, 1950

By C. B. Sclar and

A graphical solution is presented for the equation v =v &-cU where vb is the volume of liquid b of density 6 that must be added to liquid a of volume va and density d, in order to obtain a heavy-liquid solution of preferred density dm for mineral fractionation. The equation is valid only for pairs of liquids whose volumes are additive, but empirical density-composi-tion data show that this condition is met over wide compositional ranges by all of the heavy solutions that are commonly used for mineralogical analysis. The chart is a nomograph which consists of two horizontal volume scales ad a vertical density scale arranged so that one volume scale occurs on each side of the density scale. All the scales are linear. For two liquids of density d, and &, respectively, each volume scale has an independent level on the density scale, ad the graphical solution for vb on the nomograph is obtained by construction of one straight line. The chart can be prepared easily to cover any density range with any desired accuracy by proper selection of the scales. Heavy-liquid separation of particulate samples is an indispensable analytical procedure in the mineralogical and mineral-process ing laboratory. Heavy liquids may be used 1) to isolate specific minerals in the form of high purity products or to fractionate samples into several products with density limits for petrographic, chemical, spectrographic, and X-ray diffraction analysis,'-' 2) to determine the density of minerals,'-l4 3) to facilitate the recognition and identification of optically similar associated minerals,15 and 4) to determine quantitatively the degree of liberation of ore minerals in ores and mill products at various limiting sizes." The preparation and recovery of heavy liquids suitable for mineralogical analysis are discussed fully in the literature and operational procedures and special equipment for heavy-liquid separation are described in numerous references.'747837' 13,18,25-42 Useful tabulations of heavy liquids for mineralogical analysis are given by Tickell, Mil-ner,' Twenhofel and Tyler,' and Lange and a very complete up-to-date list of minerals arranged according to increasing density is given by Mursky and Thompson. USEFULNESS OF THE DENSITY CHART For any particulate sample, the limiting densities selected for its fractionation by means of heavy- liquid separation depend on the respective densities of the constituent minerals and the specific objectives of the separation. In many instances, the densities of readily available and practicable heavy liquids do not coincide with those that are required, and suitable liquids of the proper density are obtained by dilution with miscible liquids. In the general case, one may wish to mix either a pure liquid (A) or a solution of two miscible liquids (AP,,) of known density with either a pure liquid (B) or a different solution of the two miscible liquids (A,B,) of higher or lower density in order to obtain a final liquid of the preferred density. In conventional practice, the latter is reached empirically by trial-and-error addition of increments of one liquid to the other. The density of the final solution may be determined either by accurately weighing a known volume of the final liquid,'' 532;4;40, or by means of I)a Westphal balance, 2)a hydrometer, a refractometer in the case of binary liquid systems for which density-refractive index data are available,15 4) natural or synthetic .indicators of known density, a pycno-meter. Like all trial-and-error methods, these procedures are time consuming and many require special equipment which may not be available, The purpose of this paper is to show that the volume of a liquid of known density which is to be added to another liquid of known volume and density in order to obtain a solution with an intermediate preferred density may be determined rapidly and accurately by a graphical method provided that the two liquids form ideal or quasi-ideal solutions whose volumes are additive. Empirical data47'8~'8~4B'49 show that solutions prepared from pairs of miscible

Jan 1, 1961

By J. S. Bryner

In the study of metallographic specimens in the electron microscope, there is need for a method of locating the same field in both the light microscope and the electron microscope. This need arises chiefly from the fact that in the electron microscope the magnification and degree of resolution are so much higher, and the field so much smaller than in the light rnicroscope that it is often difficult, if not impossible, to identify positively what is being observed. The difficulty is increased by the fact that, because a transparent film replica of the metal surface must be used in the electron microscope, micro-constituents can be identified not by their color but only by their texture and contours. For these reasons it is desirable to obtain a series of photographs showing the same field in both microscopes in order that the appearance of common microstructures and micro-constituents in the electron microscope may be identified and catalogued for future reference. The need for a method of locating the same field in both microscopes arises also when it becomes desirable to enlarge in the electron microscope for more detailed study a particular interesting structure observed in the light microscope. Using the standard polystyrene-silicalJ replica technique, in which the silica film replica is fished from the ethyl bromide on a 1/8 in. diam zoo-mesh specimen screen, the possibilities of locating a particular area on the film in the electron microscope are rather remote. The desired structure may be obscured by the wires of the specimen screen or unrecognizable at the high magnification. A solution to the problem would be provided if a specially designed specimen screen, containing an opening which could be absolutely identified and quickly located in the electron microscope, could be fastened to the silica film replica in such a position that the desired field on the specimen would be located at the identifiable opening in the specimen screen. The design for such a specimen screen, a method for producing it, and a technique for fastening it to the silica film replica are described below. Description OF Method The Specimen Screen A simple design for a specimen screen containing an opening easy to identify and locate in the electron microscope is one with two lines of openings at right angles in the form of a cross. Such a screen is shown in Fig I. The opening at the center of the cross is identified easily and can be located quickly in the light microscope and in the objective image of the electron microscope. The specially designed specimen screens for this work were produced in quantity by electroforming. On both sides of a polished strip of copper I X 3 X 1/8 in., twenty patterns of the cross of openings were punched with a diamond point micro-hardness tester, using a load of magnitude

Jan 1, 1949