Search Documents

By C. N. Garman

Homestake-New Mexico Partners operate a 750-tpd carbonate leach uranium concentrate mill near Grants, N.M. The highly mineralized water available as process water leaves much to be desired. The 628 ppm as CaCO 3 makes the use of raw water very troublesome in pipes and on filter cloths. However, the residual sodium carbonate in the final filter cake going to tails makes an ideal softening agent. To take advantage of this fact, all makeup water used in the mill is first used as tailing slurry dilution water and comes to the mill from the tailings pond. The 5-acre tailings pond serves as a thickener and 100 to 150 gpm of nearly clear solution is decanted to a pump to be returned to the mill. Since this tailings water has small quantities of uranium in the solution an ion exchange scavenger unit was installed to remove as much uranium as possible. The ion exchange raffinate is then used as final filter wash ahead of the tailings slurrying step. In spite of the large settling area this return water is not clean enough for ion exchange feed. The solids present are very fine and composed of approximately 15 pct (by weight) burnable carbonaceous material common to the sandstone uranium ores in the area, 40 pct SiOz plus 45 pct CaC03. Laboratory work showed that this material responds very well to flotation. Before deciding to use flotation, various clarifying systems such as pressure leaf filters, sand filters, and continuous vacuum pre-coat filters, were considered. Each of these could have solved the problem but with much more operating labor, more reagents and greater installation costs than the flotation step. About 100 to 150 gpm of fouled water is fed to two 66-in. Fagergren cells, in series. Reagents used at the beginning were Arquad 2HT75 and Arquad C50, at the rate of about 1% lb per 8-hr shift, or about 0.0053 lb each per ton of ore. This did not completely remove the solids but does an acceptable job. Approximately 75 pct of the slimes are a size that can be caught on a 41-Whatman Paper are removed. Removal of these slimes also allows much better settling of the coarse nonfloatable material. Advantage is also taken of this fact in a small settling tank ahead of precipitation. Removal of this amount of the slimes makes the ion t:xchange feasible. PREGNANT SOLUTION CIRCUIT The carbonate? leach-caustic precipitation method of uranium concertration does not provide for any process purification step ahead of precipitation. Therefore, any fine solids getting into the pregnant solution through the filter cloth show up in the final concentrate. This, of course, lowers the grade, and, at times, the slimy nature of these very fine solids rendered final filtration of the concentrate difficult if not impossible At Homestake-New Mexico Partners a 75-ft thickener was available for gravity clarification of 100 to 120 gpm of this pregnant solution. However this did not sufficiently remove the slimes. Laboratory investigation of the whole range of flocculants that were suggested by literature, salesmen, and friends failed to turn up anything of consequence. A continuous vacuum pre-coat filter would do the job and was investigated. The capital cost and the operating labor and materials made this a last chance choice. Following work done in the metallurgical laboratory on the tailings return water, it was found that some changes in the reagent strengths and combinations made a very definite decrease in the solids in the pregnant solution. Concentrate grade improved about 5 pct anti the final product after drying had an appreciably greater bulk density. Compared to a cost of about 2.2e per ton for pre-coat filter opelation for cleaning just one circuit, flotation costs less than 1.0 per ton of ore for cleaning two circuits. While a pre-coat filter would do a more thorough job, the flotation does all that is required for either circuit. Gravity causes the froth produced to run back into the leach circuit. This does not appear to result in a build-up of objectionable slime. No extra manpower is required; the operators in the separate areas can observe the operation of the cells and mix the small quantities of reagents as needed. Normally the 66-in. Fagergren cell requires 15 hp per cell, but this very dilute slurry needs only 10 hp for both cells. Originally, a combination of the two Arquads mentioned previously served as frothers and promoters. As further testing

Jan 1, 1962

By T. M. Gurr

The United States is the world's leading producer of phosphate rock. In 1975 according to the US Bureau of Mines' statistics, 44.3 million tonnes (48.8 million st) of phosphate rock were produced in the United States, l which is 40.6% of the world's production.2 The major phosphate producing areas of the United States are located in [Fig. 1] and the production for 1975 is listed as follows: [ ] All of these areas produce phosphate from deposits which are of marine sedimentary origin. Occurrences of phosphate exist throughout the United States in numerous locations that are of both igneous and sedimentary origins. However, these other phosphate occurrences vary greatly in extent and economic significance. Georgia, South Carolina, California, Texas, Arkansas, Kansas, Iowa, Alabama, Kentucky, and Virginia are but a few of the states in which phosphate is thought or known to exist. The near future expansion will probably continue to be in, or near, existing producing areas, (i.e., Florida and North Carolina).

Jan 1, 1980

By Benjamin C. Koskiniemi

Introduction When evaluating any ore body, one of the first questions concerns the ore reserves. In the case of an open pit mine, this is not possible to answer reliably until the ultimate (final) pit limits have been established. Techniques used in designing an ultimate pit are classed as (1) manual, (2) computer, and (3) combined manual-computer. This chapter will describe how manual techniques can be utilized in designing an ulti¬mate pit Certain economic and design criteria must be established before the actual design begins In order to begin designing an ultimate pit, it will be assumed that the engineer already has the following data available (1) vertical sections, (2) horizontal sections for each level, (3) stripping curve, (4) bench height, (5) bank slope angle between levels, (6) level berm width, (7) roadway width, (8) pit slope angles at ultimate pit limits (estimated average including roads and ramps and between roads and ramps), and (9) minimum width of pit bottom

Jan 1, 1979

By S. F. Willey

Difficulties encountered in justifying replacements for overage mobile mine equipment at the Gay mine are common to most mining operations. More critical management reviews, resulting from ever rising capital expenses, increased such difficulties. These increased difficulties are especially apparent to those who are primarily operators and are not statisticians, mathematicians or computer men. The Gay mine is located 17 mi east of the town of Fort Hall in southern Idaho. This open pit operation annually supplies the J. R. Simplot Co. and the FMC Corp. with 1.5-2.0 million tons of phosphate ore. Stripping ratios average approximately three bank cubic yards of waste per ton of ore mined. The mobile mine equipment fleet consists of ten 24-cu yd scrapers; twenty-one 30-50-ton end-dump trucks; four 3%-4%- cu yd shovels; fifteen dozers in the D-8 and D-9 classes; and three road patrols. Equipment replacement is based on the results of evaluations made on individual units.

Jan 9, 1972

By Earl Kennedy

The Northern West Virginia Region of Consolidation Coal Company consists of ten underground mines. The Pittsburgh seam of coal is being mined. This seam is approximately seven feet in thickness in our area. The mining equipment consists of twelve longwall systems and a combination of Joy and Jeffrey ripper type miners. There are a few boring type machines still in use, but these are rapidly being phased out. The auxiliary ventilation fans being utilized vary in type from single stage carriage mounted 20 horse-power Joys to 40 and 50 horsepower two-stage Joys, Buffalo Forge, and Peabody brands. The particular fans that we have primarily been working with on noise reduction are the two-stage 40 and 50 horsepower types.

Jan 1, 1982

By Clyde Longyear

DURING the last two years, the diamond core drill has come rapidly to the front as a very valuable auxiliary to the equipment of the exploration and production departments of oil companies. The diamond drill and the rotary oil drill work on the same general principles, the essential difference being that the diamond drill employs an annular steel bit set with black diamonds ("carbons"), instead of the fish-tail or other type of bit employed by the rotary drill. On account of the brittleness of the carbon and the danger of breakage if subjected to sudden blows or stresses, it is not practicable to attach a diamond bit and core-barrel to the end of a rotary drill stem. The operating mechanism of the diamond drill must be subject to much more sensitive control than the rotary drill. The bit must be rotated smoothly, without the jerks that are incident to the operation of the clutches and chain drives on the rotary draw works, and the feed must be con-trolled in a much more delicate manner than the mere action of a brake on a hoist. To accomplish this smooth rotation, diamond drills are usually built as a self-con-tained unit with the crank shaft of the engine geared direct to the drive shaft that turns the drill rods or stem. One or two hydraulic cylinders connected with a high-pressure pump control the feed so definitely that the bit can be raised or lowered at will, while the bit is rotating, by the simple operation of valves. The smaller-sized-drills for very shallow work usually have a screw feed control instead of the hydraulic feed. The principal uses of the diamond drill in oil work are three: 1. Reconnaissance or structure drilling; that is, the drilling of a number of shallow holes to ascertain the subsurface contour. 2. Scout drilling, or the drilling of holes of smaller diameter than is required for production, to obtain information as to the character of the oil sand and the quality of the oil. 3. Drilling producing wells.

Jan 5, 1923

For the benefit of those of our members who are considerable holders of securities, but owing to their isolated situations are not in close touch with the metropolitan market and current quotations, we are publishing two very interesting graphs, showing the course of the bond and stock markets in New York over a long period. These graphs are furnished through the courtesy of the financial department of the New York Tribune.

Jan 12, 1919

PRESIDENT SIDNEY J. JENNINGS NEW YORK, N. Y. PAST PRESIDENTS L. D. RICKETTS NEW YORK, N. Y. PHILIP N. MOORE FIRST VICE-PRESIDENT C. W. GOODALE BUTTE, MONT. TREASURER GEORGE C. STONE, NEW YORK, N. Y. SECRETARY. EMERITUS ROSSITER W. RAYMOND, NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON, NEW YORK, N. Y.

Jan 5, 1918

By J. Parke Channing

THE growth of and profession depends on meeting and solving new problems. It is a continuous process. 'A period free from new, or hitherto unknown, questions will be a period of arrested development in the profession it affects. The present generation has witnessed a' mechanical development that has been truly marvelous: Almost every day marks the advent of a new, or the improvement of an old; process, method or machine. Wonders are now commonplace. The impossible is regularly accomplished. Yet, with all our progress in every realm of science and with our development in the engineering field, advances which have made possible the marvelous growth in industry, we have not made commensurate gains in methods affecting the human factor. Without the cooperation of the worker, we shall always fall short of our goal in a mechanical or statistical sense. If we do not make the individual members of the human family strong, healthy, happy, and ambitious for better things for themselves and their children, we will have failed utterly, for that is the real reason for our existence as men and the purpose of our organized effort as an engineering group. Thomas A. Edison

Jan 1, 1921

By A. L. Simpson, J. M. Edwards

The application of the Scintillometer to radioactivrty surveys in boreholes of oil wells has made it possible to determine bed thickness with a high degree of accuracy. This fact, combined with known relation of logging variables, makes thin bed porosity determination practical. With the use of the Scintillometer a method hot been derived whereby the apparent level of radiactivity, as recorded on radiation logs, may be converted to the true level. The true level of radioactivity is that level to which the recording pen would have traveled had the detector remained at a given depth for on infinitely long period of time. This factor is: radioactivity level, Ra, is the apparent radioactivity level, T is the bed thickness, D is drag, and L is the length of the detecting system. This method depends entirely on accurate measurements of bed thickness and drag. A thorough discussion of the concept of time constant and logging speed as related to drag is undertaken. INTRODUCTION Neutron curve interpretation has become one of the accepted methods for porosity determination in oil field practices. A great deal of literature has been published about neutron derived porosities, but this has been concerned with thick beds, or possibly even averaging of a series of thin beds as a single unit. There has been a lack of written information on methods whereby porosity can be evaluated for beds less than 10 ft in thickness. In certain areas, production is derived from relatively thin formations. The importance of thin bed evaluation, the fact that the Scintillometer is an adequate tool for this application, and the general lack of published information concerning neutron porosity for thin beds are the fundamental reasons for presenting this method of porosity determination. This concept is not put forth with the idea of discounting existing methods, but is merely suggested as a modification of other accepted methods of porosity determination which makes no allowance for quantitative evaluation of thin beds. The effects on the neutron log of counting statistics, statistical variation in the porosity of earth materials, and hole size must be taken into account to obtain neutron derived porosities. Since these effects have been described in past literature, the authors have not made an attempt to go into the subject in detail. With the use of statistical and repeated sections on the log, it may be determined which responses on the log actually correspond with lithologic changes. EFFECT OF DRAG AND ITS RELATIONSHIP TO TIME CONSTANT AND LOGGING SPEED Before entering into a discussion of porosity determination of thin beds, there should be a thorough

Jan 1, 1956

"The cleanliness and system evidenced in the accompanying photographs of the West Steward change-house will appeal to all mine operators. This design is the most efficient in use at Butte. It is the standard which will probably be used in Butte in all future construction and is the result of a long period of investigation and experimenting. It is important that such a structure be as nearly fire-proof as possible, because of the frequent fires originating within the lockers from matches, etc., in the men's clothes. The concrete floors permit the thorough washing of the building whenever necessary.The lockers are roomy and well ventilated. They are constructed of sheet steel and are warmed from below by steam pipes."

Jan 1, 1913

PHOTO

Jan 1, 1928

By J. O. Brittain, E. P. Lautenschlager, F. Felberbauer

This investigation was undertaken to evaluate the effect of a dispersed phase in a iron upon the strain hardening and the stress dependency of dislocation velocity as inferred from the strain-rate sensitivitv. Experiments were made in a-iron specimens with controlled amounts of carbon and/or A12O3. They were tested at various temperatures between 195' and 373 'K under a variety of conditions oj-concentration, strain rate, and quench aging. The resulting yield strength, flow strength, and strain hardening increased with addition of Al2O3. The parameter m, measured from changes in strain rate, was xsed to describe the stress dependency of the dislocation velocity. m was found to increase with additions of A12O3, increasing carbon in solution, and with increasing temperature. When applied to a recent model for yielding based upon dislocation multiplication and velocity characteristics, the values of m alone did not successfully predict yielding for the materials of this investigalion, but had to be adjusted with a consideration of the number of unlocked dislocations nucleated heterogeneously at discontinuities or inclusions. The change of yield strength with Al2O3 Interpar-ticle spacing appeared to obey a theory of Orowan. EVER since the concept of dislocations has been introduced to explain plastic deformation in crystalline materials, the origin of dislocations and the source of the number of dislocations required to account for plastic deformation have been persistent questions. Ruling out the possibility of homogeneous nucleation,' Gilman2 drew attention to the various cases of heterogeneous nucleation as the source of dislocations, whereas Frank and Read3 introduced the Frank-Read source. However, Gil-man found that the Frank-Read sources did not play a dominant role in the deformation of LiF crystals, but that small precipitates are often, if not always, associated with the nucleation of dislocations. In LiF crystals, however, most of the dislocations arose through the multiplication of moving dislocations in a mechanism described by Koehler4 and Orowan,5 Thus, relatively few precipitates could account for a large number of dislocations. A similar observation of dislocation nucleation at inclusions of precipitates was made by Stein and LOW' on Si-Fe crystals. Their crystals contained

Jan 1, 1964

By E. Miller, J. M. Eldridge, K. L. Komarek

The thermodynamic properties of- liquid Mg-Pb allojs have been determined by an isopiestic method from 18 to 42 at. pct Pb and by a thevmodynumic analysis of the phase diagram frofiz 0 to 100 at. pct Pb. In the overlapping composition range the magneszupn activity values derived by the two methods are in excellent agreement, thus mutually supporting the correctness of the Mg-Pb phase diagram previously determined by the authors and of the acticitzes deriz~ed isopiestically. SEVERAL studies have been made of the thermody-namic properties of liquid Mg-Pb alloys. Wagner and Engelhardt,1 Lantratov,2 Knappwost,3 Sryvalin et al.* and Wilson5 used the electromotive-force method, Scheil and Wolf8 and Schmahl and Sieben" applied the transpiration technique, and the present authors8 utilized the phase diagram to determine the activity of magnesium in the Mg-Pb system. The results of these studies are not in very good agreement and could not be incorporated into a general systematic analysis of the thermodynamic properties of the homologous series of the Mg-Group IV B systems Mg-Pb,8 Mg-Sn,° Mg-Ge,10and Mg-Si.11 The thermodynamic properties of the Mg-Pb system were therefore re investigated by an isopiestic technique which has been developed for similar studies in the Mg-SnB and Mg-Ge10 systems- Lead specimens, contained in iron or graphite crucibles, were heated in a temperature gradient in an evacuated and sealed titanium reaction tube and equilibrated with magnesium vapor of known vapor pressure to form alloys of compositions which depended on their temperatures, the temperature of the magnesium vapor source, and the thermodynamic properties of the system. EXPERIMENTAL PROCEDURE Magnesium (Dominion Magnesium Ltd., Toronto, Canada) of 99.99+ pct purity and lead (American Smelting and Refining Co.) of 99.999 pct purity were used. In the early experiments, Runs 2 and 3, the alloys were contained in uncovered high-purity iron crucibles. Alloys formed in the uncovered iron crucibles had to be chemically analyzed owing to the slight volatility of lead under the imposed experimental equilibration conditions. The compositions of these alloys were determined by a gravimetric analysis of lead as lead chromate. To avoid this problem, the remaining runs were made in covered graphite crucibles machined from high-density (1.92 g per cu cm) graphite rods (Basic Carbon Corp., Sanborn, N.Y.) which had a maximum ash content of less than 0.04 pct. The non- i reactivity of graphite with lead and magnesium has been previously established,' and the experimental procedure has been described in full detail.' In the runs using covered graphite crucibles it was found that the weight increases of the crucibles and their contents after equilibration equaled the magnesium contents of the alloys within the accuracy of the chemical analysis (i0.3 at. pct Pb). Clearly, the small lid openings of the graphite crucibles prevented significant lead losses during a run, and the weight increase was therefore taken as the magnesium content of the alloys. EXPERIMENTAL RESULTS At thermodynamic equilibrium the magnesium partial pressure of the specimens equaled that of the reservoir. Since the magnesium reservoir was always maintained at the temperature minimum of the system, the activity of magnesium of any specimen was given by the ratio of the magnesium reservoir pressure to the vapor pressure of pure magnesium at the specimen temperature. The standard state was chosen as liquid magnesium and the vapor pressure of liquid magnesium

Jan 1, 1968

By P. D. Southgate

VIBRATION, both ultrasonic and sonic, can affect the course of a variety of metallurgical processes. Reports of work on this subject have appeared at intervals over the last twenty years and a thorough review has been made by Hiedemann,' who gives a full list of references. It has been established that both refinement of structure and outgassing of the melt can be produced in most metals with sufficiently intense vibration. Many of the experiments in this field have been carried out using alloys of direct commercial interest in production- type casting equipment. Here a different approach is adopted, and simple binary alloys which exhibit different types of structure are used to facilitate examination of the effects produced under well-controlled conditions. Results from this kind of experiment should enable the basis of larger scale experiments with similar types of materials to be better substantiated. The alloys selected for this work are: 1) aluminum of 99.2 pct purity, the principal impurity being iron, near 0.4 pct; 2) A1-1.8 pct Fe, which is near eutectic composition; 3) A1-4 pct Fe—the second phase, of composition FeAl3, forms distinct acicular crystals; and 4) A1-12 pct Si—although this is of eutectic composition, the silicon normally appears in the form of large plates. Experimental Method There are three practicable methods by which acoustic vibration can be transferred to liquid metals: a) vibration of the whole of the container; b) electromagnetic induction; and c) insertion of a vibrating probe into the liquid. Method c is chosen here, and a frequency of 8 kc per sec is used. The end of the probe is electrically heated so that the metal near it will be the last to solidify. This ensures that vibration is transmitted directly to the liquid metal without passing through any solidifying and pasty intermediate region, which would attenuate acoustic waves severely. In addition, the heating prevents solid metal adhering to the probe, with consequent detuning. The transducer assembly is shown in Fig. 1. A stack of Permendur laminations 30 cm long acts as a half-wave vibrator and a winding along its length carries polarizing and energizing currents. It is joined by a half-wave coupling bar to a mild steel exponential horn, which tapers from 3.8 to 1.1 cm diam. A stainless steel stub 3 cm in length is welded on the free end. The assembly is supported by a plate located at the node of the coupling bar. Acoustic radiation losses are minimized by allowing the free end of the transducer to protrude above the surface of the cooling water. The exponential horn serves the function of matching the acoustic output impedance of the transducer to the radiation resistance of the probe into the melt. Electrical drive is provided by a 1 kw generator. Measurements of probe vibration amplitude during melt treatment are obtained from a gramophone pick-up with the needle attached to the wide end of the horn. This device is calibrated with a microscope before use. Liquid aluminum is very actively erosive and solution of materials with which the molten metal comes into contactcauses difficulties. Erosion of the probes in particular can be severe since it is greatly accelerated by the vibration. Tests of various acous-

Jan 1, 1958

The Year Book of the Institute will be mailed with, the May Bulletin. Its membership lists, both alphabetic and geographic, are corrected to Mar. 1, and the lists of officers and committees are corrected to date.

Jan 4, 1919

For the benefit of those of our members who are considerable holders of securities, but owing to their isolated situations are not in-close touch with the metropolitan market and current quotations, we are publishing two very interesting graphs, showing the course of the bond and stock markets in New York over a long period. These graphs are furnished through the courtesy of the financial department of the New York Tribune.

Jan 5, 1919

For the benefit of those of our members who are considerable holders of securities, but owing to their isolated situations are not in close touch with the metropolitan market and current quotations, we are publishing two very interesting graphs, showing the course of the bond and stock markets in New York over a long period. These graphs are furnished through the courtesy of the financial department of the New York Tribune.

Jan 7, 1919

For the benefit of those of our members who are considerable holders of securities, but owing to their isolated situations are not in close touch. with the, metropolitan market and current quotations, we are publishing two very interesting graphs, showing the course of the bond and stock markets in New York over a long period. These graphs are furnished through the courtesy of the financial department of the New York Tribune.

Jan 9, 1919

By E. I. Salkovitz, F. W. von Batchelder

AS Slawson1 and others have already shown, from a geometrical view twinning in the diamond structure may be considered as a reflection across a (111) plane or as a reflection across a (112) plane. An analysis by Ellis and Treuting2 showed that the twinning plane must be the (111) plane, but that a twin might have lateral boundaries along (112) planes. Earlier Slawson1 and Ellis3 had shown that only (111) twinning was present in diamond and germanium respectively. Since an ingot of silicon, 1 in. in diam and 1 1/2 in. long, prepared from Dupont silicon to which 0.2 pct Be had been added was available, it was examined for twinning. The ingot had been cooled slowly from the bottom. A section 1/16 in. thick was ground off from the bottom and then the ingot was sliced vertically through the center. Spectrographic analysis indicated only faint traces of iron and silver, in addition to the beryllium. The sample was first etched with a hot solution of 10 pct NaOH in water.and photographed. Back-reflection Laue patterns were made of the vertical and horizontal sections in the regions designated in Fig. 1. Orientations were obtained for each twin using the Greninger technique. Several regions of the same orientation were found; thus regions A and K were identical, similarly N and P, and C, G, J, and L. Knowing the angles between the traces of the twinning plane on the surface and the specimen axis, the indices of the twinning plane were deduced. In all cases the twinning plane was found to be (111); lateral boundaries, however, were found which were (112) such as the one indicated in Fig. 1. Therefore, as in the case of diamond1 and germanium' only (111) twinning occurs in silicon. We wish to thank Mr. Hino for the use of the ingot as well as for its metallographic preparation. References 1C. B. Slawson: American Mineralogist (1950) 35, p. 193. 2 W. C. Ellis and R. C. Treuting: Trans. AIME (1951) 191, p. 53; Journal of Metals (January 1951). 3W. C. Ellis: Trans. AIME (1950) 188, p. 886; Journal of Metals (June 1950).

Jan 1, 1953