Search Documents

By W. H. Blauvelt

W. H. BLAUVELT, Syracuse, N. Y. (communication to the Secretary*).-I have read Mr. Howland's paper on Calculations with Reference to the Use of Carbon in Modern American Blast Furnaces with much interest, and believe that his method of analysis of the subject will be of material assistance in our study of the action of coke in the blast furnace. Mr. Howland quotes Professor Richards' statement that from the standpoint of the generation of the maximum quantity of heat in the furnace, Grüner was right in saying that all the carbon burned in the furnace should be first oxidized at the tuyères to CO and all reduction of oxides above the tuyères should be caused by CO, which thus becomes CO2. It is clear that the maximum quantity of heat is generated in the furnace when the greatest amount of carbon is burned to CO2 irrespective of whether it is burned at the tuyères or further up the furnace. So it would appear that Grüner's theory is sound regarding the maximum production of heat only because if all the carbon is burned to CO at the tuyères the reduction of the ores will have to be effected by the further oxidation to CO2. Whereas, if the reduction of the ores is effected in part by solid carbon, part of this carbon might be oxidized only to CO, resulting in a higher percentage of CO in the escaping gases than from Grüner's "ideal conditions.? But in studying the combustion of coke in the furnace, it is clear that the production of the maximum quantity of heat is not of the first importance in blast-furnace operation, or in the utilization of the fuel charged into the furnace. To my mind the production of a high thermal head at the tuyères is of the first importance, and the best coke is that which reaches the tuyères in proper condition to produce the highest temperature at the tuyères, and in just sufficient quantity to do the amount of work required there under the conditions produced by this maximum temperature. The combustion of a much larger amount of fuel at the tuyères, under conditions that will fall short of producing the highest possible temperature, cannot produce as good results, either in fuel economy or output. If this statement is correct, does it not correspond with Mr. Howland's statement that too much wind is inimical to low coke consumption? Nothing is more fatal to obtaining the highest temperatures than an excess of air for combustion. In the blast furnace an excess of air dilutes and cools the products of combus-

Jan 10, 1916

By Richard Addison, Ronald O. Cranor

Tailings dam construction and operation of Rosario Dominicana's gold/silver mine in the Dominican Republic is described. Impoundment of 8.5 kt/d of cyanide-process tailings is required in an intensive agricultural area which is also an earthquake and high rainfall zone. The earthfill embankment dam, incorporating internal gravel drains, is described together with methods of construction used. Methods of tailings transport, solution reclaim, and runoff water diversion that have evolved are discussed.

Jan 1, 1982

By R. A. Wagstaff

MANY changes in equipment have had to be made to handle the flotation products at the blast furnace, and these changes have meant an expenditure of considerable money, which has not been compensated by an increase in smelting tonnage. To date, very few new lead mines have been developed, so that the help derived by the innovation of flotation has been directed to old producing properties, where the ratio of concentration is greater now than when gravity concentration was in effect. In some smelting plants there has been an abandonment of complete units due to the introduction of flotation. FLOTATION PRODUCTS DIFFICULT TO HANDLE The physical characteristics of the flotation product do not make for economic handling for lead blast-furnace work, either mechanically or metallurgically. The millman or miner do not know what trials and tribulations they have passed on to the smelterman. To the smelterman it is "the everchanging flotation," for little does he know what new reagent will be perfected tomorrow that may completely change the grade and physical characteristics of the product. Even the mining companies who have complete units of mining, milling and smelting have had a hard time to reconcile themselves to the fact that the unit cost per ton of ore smelted must go up with the increase of flotation product on the blast-furnace charge. The "smelterman's burden," for that is what flotation has been for the last few years, has not caused the smelter operator to lag or fall down, but has spurred him on with new zeal. The physical properties of the flotation products are as follows: (1) High moisture content; (2) mucky nature of product; (3) fineness of product, and (4) high metal content. NEW MECHANICAL DEVICES FOR HANDLING FURNACE PRODUCT These characteristics have caused the use of many new mechanical devices in smelting practice, for example: New transportation equipment, such as solid-bottom cars, is required; unloading equipment and sampling

Jan 1, 1928

By Gerald Edmunds

THE liquidus line on the phase diagram for temperature versus composition of a binary alloy system, representing the boundary between the homogeneous melt and the heterogeneous melt plus solid, besides showing the minimum casting temperature, is useful in determining eutectic compositions and the presence of phase changes such as peritectic transformations and intermetallic compound formation. The liquidus often is determined by the cooling curves of thermal analysis, but supercooling frequently occurs, so that the temperature values are low. An alternative method, the one employed here, consists of determining the com- position of samples of the melts from heterogeneous alloys that are at equilibrium. With meticulous attention to fundamentals, this method is capable of yielding values limited in precision only by the temperature control and measurement and analyses. APPARATUS By starting, on the one hand, with a supersaturated solution and allowing the excess solute to precipitate, and on the other hand with an undersaturated solution and allowing more of the solute to be dissolved, both processes being carried out at the same temperature, equilibrium may be said to have been approached from both directions; that is, from above and from below. If the analyses show the solutions to contain the same fraction of solute when equilibrium has been approached from above and from below, one is assured that equilibrium has been reached in both determinations. In order to carry out such determinations, it is necessary to have equipment for obtaining and maintaining the proper temperatures; for holding the melt, measuring its temperature, and stirring, sampling and analyzing it. The present work required temperatures from 420° to 900°C. The equipment consisted of: A furnace, which was a vertical alundum tube, 1 ¾ in. diameter inside and 18 in. long, wound with Nichrome resistance wire, surrounded by a 3-in. i.d. alundum tube wound for 5 in. of length near each end, for compensation of end losses. This muffle was contained in an iron shell with Transite end plates, the intervening space being packed with Sil-O-Cel. The outside dimensions of the furnace were 12 in. in diameter by 18 ½ in. in height. Heating current was supplied by three independent variable-voltage transformers (Variac), one connected to each end compensator winding and manually controlled, and one connected to the main winding through a series resistance of 5 ohms. This resistance was short-circuited for

Jan 1, 1944

By Roy J. Helfinstine

One of the most urgent needs in the field of coal combustion is the ability to predict the performance of a coal from knowledge gained from small-scale tests. Numerous types of analyses and tests are conducted on coal, including the proximate and ultimate analyses, heating value, varieties of sulphur, ash analysis, ash fusion temperatures, free swelling index, petrographic analysis, and Gieseler plasticity. The Illinois Geological Survey has made an intensive study of the value of these tests for judging the performance characteristics of the coal as actually utilized. To date, three reports 1 2 3 have been is- sued, and another is being prepared. The present paper briefly summarizes some of the results found in the studies.

Jan 1, 1949

By Y. C. Liu, W. R. Hibbard

An aluminum single crystal cold-rolled from (110) [1121 essentially retains its initial orientation after 99.6 pct reduction in thickness. The orientation of the recrys-tallized grains of this material can be described in terms of crystallographic rotations about principal poles of deformation texture. DURING the study of the recrystallization of a copper single crystal cold-rolled from a (110) [112] initial orientation, the orientation of the re-crystallized grains could be derived by a 30" rotation of the orientation of the cold-rolled matrix about its <111> poles.&apos; The present investigation was undertaken to extend the work done on copper&apos; to an aluminum crystal also cold-rolled from a (110) [112] initial orientation. Experimental Procedure The procedure of this experiment was similar to that reported for copper.&apos; An aluminum (99.998 pct) single crystal rod* 1 % in. in diameter was grown in back-reflection technique.&apos; The specimen (1.20x 1.004x0.6787 in. thick) was then rolled along the [112] direction. The final thickness was 0.0028 in., giving a reduction in thickness of about 99.6 pet. Specimens were cut from the rolled strip with scissors, and approximately in. of disturbed metal was removed with Tucker&apos;s reagent. The rolling edge remained intact. The specimens were sandwiched between two graphite plates and annealed in a lead or lead alloy bath which was electrically heated. Pole figures were constructed using the techniques previously described.&apos; Specimens were electrolytically polished4 and etched with 47 pct HNO8, 50 pct HC1, and 3 pct of 48 pct HF. The electrolytic polishing method and etching reagent employed for aluminum specimens were not entirely satisfactory and the microstruc-tures could not be studied in any detail. Results and Discussion The octahedral pole figure of cold-rolled aluminum strip is plotted in Fig. 1. The <111> poles spread in the transverse direction approximately 8" for the highest intensity areas. The spread in the transverse direction can be related to a rotation about two <110> directions lying in a plane containing the rolling direction and rolling plane normal. The two <110> directions and a scale of rotation for the <111> poles are shown in Fig. 2. The amount of rotation is consistent for three of the four <111> poles, about 35" to 40". The discrepancy for the fourth pole is believed to be due to limitations of the film technique. Alternate inter-

Jan 1, 1956

By W. F. Stowasser

Robert E. Hagen (Oliver Iron Mining Div., U. S. Steel Corp.)—Mr. Stowasser and his associates are to be congratulated on their achievements in developing the design of a pilot agglomerating plant, based on information obtained from experiments made in a laboratory sinter pot, and subsequently constructing and successfully operating this plant. In his Transactions article, May 1955 (vol. 201) Mr. Stowasser stated that the output of his heat treating strand was about 2 Lt per sq ft of grate area per day and that the fuel consumption was 0.7 to 0.8 million Btu per Lt of product. If it is assumed that the burning zone extends from the back of the ignition furnace to the beginning of the recuperation windbox, only about 1/3 of the grate area over the windboxes is utilized for burning pellets, and the actual rate at which partially dried pellets are burned is about 6 Lt per sq ft of grate area per day. It may be interesting to compare the above operating data with that obtained at the Extaca plant, where taconite concentrate is treated on a conventional sin- tering machine using limestone or hydrated lime additives with no recuperation of heat. The entire windbox area is used for burning, and a production rate of 2.5 Lt per sq ft of windbox area per day has been attained at a fuel consumption of 1.8 to 2.0 million Btu per Lt of product, the latter being considerably in excess of that reported by Mr. Stowasser, partly because a circulating load of returns amounting to 28 to 30 pct of the machine feed is used and because no attempt is made to recuperate heat from the waste gases. With the high capital and labor costs prevailing today, it seems that future development of the downdraft grate pelletizing process should be directed toward taking advantage of the high burning rate of predried pellets and increasing capacity, perhaps at the expense of fuel economy, by decreasing the proportion of grate area utilized by ancillary functions. For example, eliminating the cooling zone and using this area for burning would increase the proportion of grate area available for burning from 33 to 50 pct of the total windbox area, and a proportionate increase in capacity would result.

Jan 1, 1956

By R. A. Wagstaff

Many changes in equipment have had to be made to handle the flotation products at the blast furnace, and these changes have meant an expenditure of considerable money, which has not been compensated by an increase in smelting tonnage. To date, very few new lead mines have been developed, so that the help derived by the innovation of flotation has been directed to old producing properties, where the ratio of concentration is greater now than when gravity concentration was in effect. In some smelting plants there has been an abandonment of complete units due to the introduction of flotation. Flotation Products Difficult to Handle The physical characteristics of the flotation product do not make for economic handling for lead blast-furnace work, either mechanically or metallurgically. The millman or miner do not know what trials and tribulations they have passed on to the smelterman. To the smelterman it is "the everchanging flotation," for little does he know what new reagent will be perfected tomorrow that may completely change the grade and physical characteristics of the product. Even the mining companies who have complete units of mining, milling and smelting have had a hard time to reconcile themselves to the fact that the unit cost per ton of ore smelted must go up with the increase of flotation product on the blast-furnace charge. The "smelterman&apos;s burden," for that is what flotation has been for the last few years, has not caused the smelter operator to lag or fall down, but has spurred him on with new zeal. The physical properties of the flotation products are as follows: (1) High moisture content; (2) mucky nature of product; (3) fineness of product, and (4) high metal content. New Mechanical Devices for Handling Furnace Product These characteristics have caused the use of many new mechanical devices in smelting practice, for example: New transportation equipment, such as solid-bottom cars, is required; unloading equipment and sampling

Jan 1, 1928

By Robert F. Brindisi

There are approximately thirty to forty operating mills in the United States which are currently producing uranium yellow cake. This figure includes a significant number of in situ and by-product operations however the conventional acid leach flowsheet depicted in Figure 1 is the most common process used by domes- tic yellow cake producers. Ground ore is leached with sulphuric acid and the solids are separated from the pregnant liquor and washed in a series of counter- current decantation thickeners. After clarification of the pregnant liquor, uranium is recovered from the solvent extraction/stripping circuit by the addition of ammonia with precipitation of ammonium diuranate, or simply yellow cake. The yellow cake precipitate is then thickened in a conventional thickener before re- porting to the dewatering/washing unit operation. De- watered solids subsequently report to thermal drying, and clarified liquor from the dewatering/washing step is recycled to the yellow cake thickener. The yellow cake dewatering/washing unit operation is generally accomplished using either a solid bowl centrifuge or a rotary vacuum drum filter. In most cases the underflow from the yellow cake thickener is pumped to the dewatering/washing unit operation at approximately fifteen to twenty percent solids. For the purpose of this discussion ammonium diuranate, the product of ammonia precipitation from a conventional acid-leach uranium mill flow sheet, as discussed earlier, will be considered. With only slight adjustment this discussion will be equally applicable to sodium diuranate or uranium perioxide precipitates and to either in situ or by-product operations where such precipitates are generated. Some of the domestic uranium mills which have selected solid bowl centrifuges instead of vacuum drum filters for the dewatering/washing unit operations are listed in Figure 2. Why have these uranium mills, as well as others not listed, chosen to use the solid bowl centrifuge for this particular application? It is simply a matter of performance, reliability and economics. In the remainder of this paper the performance, initial cost, installation cost, maintenance and power consumption of both the solid bowl centrifuge and the rotary vacuum drum filter will be com- pared. In order to provide a consistent basis for comparison the appropriate sized (centrifuge or filter) unit for the dewatering/washing of 400 to 500 pounds per hour of yellow cake solids will be considered. Such a flow will usually be generated by a typical 3,000 ton per day (acid-leach) uranium mill.

Jan 1, 1980

By William B. Stephenson

IN the pumping of sands, slurries and slimes, practices developed over the years are the real keystones of successful operation. These practices are necessarily based on modifications of familiar theories. Practical methods used in the solution of problems involving the pumping of materials are set forth in the following discussion. BASIC REQUIREMENTS To pump sands and slurries economically, a few basic requirements must be met by the pumping system as a whole. A pipe-line velocity must be established that will move the fluid mixture throughout the entire system without any possibility of the solids settling out. To accomplish this, the velocity of flow must be slightly in excess of the critical velocity of the mixture. The critical velocity of a mixture varies from 3 ft. per sec. to 18 ft. per sec., depending on the screen analysis, concentration, and specific gravity of the solids in the mixture. Most tailings are pumped at a minimum velocity of 4 ft. per sec. if they include slimes, whereas the pipe lines of sand and gravel dredges require velocities as high as 18 ft. per second. A number of articles have been written on the determination of the minimum velocities required to maintain solids in suspension. Studies have also been made on the friction and pumping heads developed when handling solids in suspension.1-4 Our experience so far has shown that, within the normal operating limits of a pumping system, the friction factor follows more nearly the basis described by Howard,1 who says, among his conclusions: " ... values of ƒ (friction factor) .. . will decrease with an increase in velocity." This conclusion is borne out by our actual experience. When the velocity in a pipe line is not sufficient to keep the solids in suspension, the total friction head is greater than when the velocity is increased to a point where the solids are in suspension. A slight increase in the volume of feed to the pump and a slight increase in the pump speed are usually all that is necessary to put the system in balance. MAINTAINING CONSTANT VOLUME Within reasonable limits, the volume of mixture to be handled through a pipe line should be held constant, so that the required velocity will be provided at all times. There are several ways in which this can be accomplished. The commonest is to provide a sump of sufficient capacity to take care of slight surges in the volume of mixture being fed to the pumping system. This sump, however, should not be as large as a settling chamber. The use of a float-controlled, fresh-water make-up valve in a sump will guarantee a constant volume. Where variations in volume are slight,

Jan 1, 1946

By C. A. Hartnagel, D. H. Newland

The market for Pennsylvania grade showed a drop both in demand and in prices, which reacted unfavorably on New York oil production, all of which comes under that classification. The output for the year in New York amounted to 5,045,200 bbl. The production in 1937 was 5,478,000 bbl., the largest in any year for the last half century or more. Falling prices, of course, affected new drilling. They declined from $2.20 a barrel, which was posted at the start, to $1.68 in the final months of 1938. With this came a reduction in the amount of oil that would be accepted by the refineries operating in the New York fields. Conditions therefore have combined to halt, at least temporarily, the growth of oil production in the state, which had experienced a steady gain for the last 15 years or more, the yield having risen from less than 1,000,000 bbl. to the round total of 5,500,000 bbl. in 1937. Practically all the oil now obtained is from old, developed fields. No new pools have been found in the last quarter of a century or more. The larger share comes from flooding the sands. Although there are many wells that still produce without the aid of the water drive, they are small and for the most part are pumped periodically. Of late, new drilling has been restricted mainly to that required to maintain existing flood projects. Because of the high initial cost and time required to put a flood into production, the depressed condition of the market has been a serious handicap financially, and, further, has been an unfavorable influence on the planning of operations to secure the maximum recovery of the oil. Unless market conditions improve, it is certain that the effects will be shown in the yield for some time to come. Gas Developments Drilling was active in the southwestern area, chiefly in Allegany and Steuben Counties, and some notable wells were brought in that tapped the Oriskany sandstone. Altogether 42 holes were put down in the two counties, of which 31 were listed as producers and 11 were dry. The new wells gave an initial daily flow of 239,000 M cu. ft. At the close of

Jan 1, 1939

By C. A. Hartnagel, D. H. Newland

The market for Pennsylvania grade showed a drop both in demand and in prices, which reacted unfavorably on New York oil production, all of which comes under that classification. The output for the year in New York amounted to 5,045,200 bbl. The production in 1937 was 5,478,000 bbl., the largest in any year for the last half century or more. Falling prices, of course, affected new drilling. They declined from $2.20 a barrel, which was posted at the start, to $1.68 in the final months of 1938. With this came a reduction in the amount of oil that would be accepted by the refineries operating in the New York fields. Conditions therefore have combined to halt, at least temporarily, the growth of oil production in the state, which had experienced a steady gain for the last 15 years or more, the yield having risen from less than 1,000,000 bbl. to the round total of 5,500,000 bbl. in 1937. Practically all the oil now obtained is from old, developed fields. No new pools have been found in the last quarter of a century or more. The larger share comes from flooding the sands. Although there are many wells that still produce without the aid of the water drive, they are small and for the most part are pumped periodically. Of late, new drilling has been restricted mainly to that required to maintain existing flood projects. Because of the high initial cost and time required to put a flood into production, the depressed condition of the market has been a serious handicap financially, and, further, has been an unfavorable influence on the planning of operations to secure the maximum recovery of the oil. Unless market conditions improve, it is certain that the effects will be shown in the yield for some time to come. Gas Developments Drilling was active in the southwestern area, chiefly in Allegany and Steuben Counties, and some notable wells were brought in that tapped the Oriskany sandstone. Altogether 42 holes were put down in the two counties, of which 31 were listed as producers and 11 were dry. The new wells gave an initial daily flow of 239,000 M cu. ft. At the close of

Jan 1, 1939

By C. E. Reistle, G. L. Nye

The East Texas field is in Smith, Rusk, Gregg, Upshur and Cherokee counties, Texas. The discovery well was completed Sept. 8, 1930, near the eastern limit of the field. Within less than one year the new field became the dominant factor in the world production of crude oil. On Aug. 16, 1931, eleven months after completion of the discovery well, there were 1644 wells in the field, and the average daily production was 584,475 bbl. Since that time the number of wells has increased to 8195 on Oct. 1, 1933, and the field has produced 385,979,691 bbl. of oil. The geology of the East Texas field has been discussed by Lahee,1 Levorsen,2 Minor and Hanna3 and others, and it will not be discussed in detail here. The field is a structure of the monocline type on the westward dipping homocline between the Sabine uplift and the East Texas geosyncline. Production is obtained from the Woodbine group, which has been truncated and then sealed by the Austin chalk, which rests unconformably upon it. The oil-saturated part of the sand lies bettween a sub-sea depth of 3050 ft. on the east side of the field, where the Woodbine sand stops and the Austin chalk rests directly upon older formations, and a sub-sea depth of 3320 ft., which was the average depth of the water table in the sand at the time the field was discovered. The field is about 40 miles long and has an average width of approximately 4 1/2 miles. The area within the proven limits of the field is close to 116,580 acres and the normal Woodbine water underlies nearly 62,000 acres on the western side of the field at the present time. The field is unusual in several respects: (1) the tremendous size of the reservoir system and the quantity of oil in place; (2) the large area of the oil and water contact, which makes water movement possible into the oil-bearing part of the structure; (3) the absence of free gas within the main producing sand of the field. Changes in the reservoir pressure during the production history of the field have been greatly affected by

Jan 1, 1934

By W. M. McKewan

Magnetite pellets were reduced in flowing hydrogen at pressures up to 40 atm over a temperature range of 350° to 500°C. The rate of weight loss of oxygen per unit area of the reaction surface was found to be constant with time at each temperature and pressure. The reaction rate was found to be directly proportional to hydrogen pressure up to 1 atm and to approach a maximum rate at high pressures. The results can be explained by considering the reaction surface to be sparsely occupied by adsorbed hydrogen at low pressures and saturated at high pressures. PREVIOUS investigation1,2 have shown that the reduction of iron oxides in hydrogen is controlled at the reaction interface. Under fixed conditions of temperature, hydrogen pressure, and gas composition, the reduction rate is constant with time, per unit surface area of residual oxide, and is directly proportional to the hydrogen pressure up to one atmosphere. The reduction rate of a sphere of iron oxide can be described3 by the following equation which takes into account the changing reaction surface area: where ro and do are the initial radius and density of the sphere; t is time; R is the fractional reduction; and R, is the reduction rate constant with units mass per area per time. The quantityis actually the fractional thickness of the reduced layer in terms of fractional reduction R. It was found in a previous investigation2 of the reduction of magnetite pellets in H2-H,O-N, mixtures, that the reaction rate was directly proportional to the hydrogen partial pressure up to 1 atm at a constant ratio of water vapor to hydrogen. Water vapor poisoned the oxide surface by an oxidizing reaction and markedly slowed the reduction. The enthalpy of activation was found to be + 13,600 cal per mole. It was also found that the magnetite reduced to meta-stable wüstite before proceeding to iron metal. The following equation was derived from absolute reaction-rate theory4,8 to expfain the experimental data: where Ro is the reduction rate in mg cm-2 min-&apos;; KO contains the conversion units; Ph2 and PH2O are the hydrogen and water vapor partial pressures in atmospheres; Ke is the equilibrium constant for the Fe,O,/FeO equilibrium; Kp is the equilibrium constant for the poisoning reaction of water vapor; L is the total number of active sites; k and h are Boltzmann&apos;s and Planck&apos;s constants; and AF is the free energy of activation. Tenenbaum zind Joseph5 studied the reduction of iron ore by hydrogen at pressures over 1 atm. They showed that increasing the hydrogen pressure materially increased the rate of reduction. This is in accordance with the work of Diepschlag,6 who found that the rate of reduction of iron ores by either carbon monoxide or hydrogen was much greater at higher pressures. He used pressures as high as 7 atm. In order to further understand the mechanism of the reduction of iron oxide by hydrogen it was decided to study the effect of increasing the hydrogen pressure on rebduction rates of magnetite pellets. EXPERIMENTAL PROCEDURE The dense magnetite pellets used in these experiments were made in the following manner. Reagent-grade ferric oxide was moistened with water and hand-rolled into spherical pellets. The pellets were heated slowly to 550°C in an atmosphere of 10 pct H2-90 pct CO, and held for 1 hr. They were then heated slowly to 1370°C in an atmosphere of 2 pct H2-98 pct CO, then cooled slowly in the same atmosphere. The sintered pellets were crystalline magnetite with an apparent density of about 4.9 gm per cm3. They were about 0.9 cm in diam. The porosity of the pellets, which was discontinuous in nature, was akrout 6 pct. The pellets were suspended from a quartz spring balance in a vertical tube furnace. The equipment is shown in Fig. 1. Essentially the furnace consists of a 12-in. OD stainless steel outer shell and a 3-in. ID inconel inner shell. The kanthal wound 22 in. long, 1 1/2, in. ID alumina reaction tube is inside the inconel inner shell. Prepurified hydrogen sweeps the reaction tube to remove the water vapor formed during the reaction. The hydrogen is static in the rest of the furnace. The sample is placed at the bottom of the furnace in a nickel wire mesh basket suspended by nickel wire from the quartz spring. The furnace is then sealed, evacuated, and refilled with argon several times to remove all traces of oxygen. It is then evacuated, filled with

Jan 1, 1962

By B. L. Averbach

Recovery and primary recrystalliza-tion in cold worked metals are usually considered as two competing processes. Some of the effects which usually accompany recovery are: alleviation of stress corrosion tendencies, changes in thermal emf,1 damping capacity,2 electrical resistivity,2 and magnetic properties,3 and only minor changes in hardness or the related strength properties. During primary recrystalliza-tion new unstrained grains are formed at the expense of the strained matrix. These new grains eventually become visible metallographically, and nucle-ation and growth kinetics have been indicated for this process.4,5 Frequent attempts have been made to study the cold-working phenomenon by observations on the line broadening by X ray diffraction patterns. Relatively few measurements of line intensities have been made, although Brind-ley and his collaborators, 6,7,8 by means of film techniques, compared the intensities of cold worked Cu, Ni, and Rh patterns with those from chemically precipitated powders. These precipitated powders were presumed to be strain free, and it was found that the intensities for the cold-worked materials progressively decreased as the Bragg angle increased except for the first line, where there was an increase due to reduction in extinction. This was interpreted as a randomness in atomic position induced by cold work. Such randomness is similar to that caused by thermal agitation and has been described as "frozen heat" displacement of 0.08-0.10 A from the mean atomic position. In a recent study9 on the effect of cold work in metals on their powder pattern intensities, the changes in integrated intensity for heavily cold worked alpha brass were observed as a function of the annealing temperature. These measurements were made with a manually operated Geiger-counter spectrometer using CuKa radiation monochromated with a rock salt crystal. Intensity measurements were made with a scaling meter over small intervals of angle, and the equipment was so arranged that the diffracted and incident beams made equal angles with the specimen. Intensities could be compared directly by simply interchanging specimens, and comparisons from day to day were made with a standard whose line intensities did not change on aging. It was shown that a cold worked alpha brass standard was stable for at least a year. Table 1 indicates the results of the integrated intensity measurements on a 70 Cu-30 Zn brass. In the sample preparation, a brass plate was first cold rolled 50 pct and then filed, screened to —325 mesh, compacted into briquettes at a pressure of 60,000 psi and finally annealed for one hour at various temperatures up to 400°C. The briquetting pressure did not seem to influence the integrated intensities, and most of the cold work was introduced by the filing. Although this method of cold work is not quantitative, it was used to obtain random orientation (and thus uniform diffraction lines) in order to make accurate measurements of integrated intensity. Back reflection patterns were taken in each case to check the uniformity of the lines, and from the observed line broadening it was apparent that this type of plastic deformation was quite severe. Care was taken to traverse the entire background of the pattern and to assign to each peak the total intensity above this background. The bases of the diffraction lines were quite broad and spread out over several degrees, even for the narrow peaks. The theoretical intensities were calculated to include a temperature correction, a dispersion correction, and a Lorenz- polarization factor corrected for the crystal monochromated beam. In Table 1 it was necessary to match the calculated and observed values at only one point, and the rest of the experimental values were converted directly to this arbitrary scale. The integrated intensities in Table 1 are listed in arbitrary units, and the accuracy was sufficient to reproduce any of the measured line intensities to within + 1.5 units. It is evident that the percentage error on the strongest line (111) was quite low. The calculated values and the observed intensities for the cold worked material matched reasonably well. As the annealing temperature was raised, however, the intensity of the strongest reflections, particularly the (lll), decreased measurably. Since the background intensities of all of these patterns were identical, such behavior could be interpreted as a primary

Jan 1, 1950

By Alfred H. Bell

The year 1937 has been outstanding in the history of the Illinois oil industry. During the course of the year the state&apos;s daily production has been trebled, increasing from 12,000 bbl. per day at the beginning to 37,000 bbl. per day at the end, and the year&apos;s total, 7,426,000 bbl. is 66 per cent above the previous year&apos;s production of 4,475,000 bbl. The production in January was 368,000 bbl.; in December it was 1,085,000. Production from the old fields increased slightly. Most of the new production is from fields in the central part of the Illinois Basin, an area that for many years was considered unfavorable to the occurrence of oil and gas. The principal producing horizon of the new fields is the McClosky "sand," an oolitic limestone in the Ste. Genevieve formation of lower Mississippian age. Although development has not yet gone far enough to permit accurate estimates of oil reserves in the new fields, it is believed that they are of the order of 100,000,000 barrels. The following are the oil fields discovered in 1937 listed in order of amount of daily production at the end of the year; Noble (Richland County), Clay City, including Southeast Clay City (Clay and Wayne counties), Patoka (Marion County), New Centralia (Clinton County), Olney (Richland County), Cisne (Wayne County),.Beecher City (Fayette County), and Rinard (Wayne County). One gas field, the Russellville, in Lawrence County, was discovered in 1937. For locations of the new fields see Fig. 1. A generalized geologic column for Illinois, showing producing horizons in the new fields, is given in Fig. 2. The total productive area of the new fields at the end of 1937 was 1712 acres, in which 230 wells were producing. Thisrty-five dry holes were drilled within 1/4 mile of producing wells. At the end of the year there were 19 drilling wells, 28 rigs standing, 18 rigging up and 4 new locations in these fields. In the whole state 447 wells were completed, of which 284 were oil producers and three gas producers. Total initial daily production of

Jan 1, 1938

By J. Lemish

Considerable research has been conducted in Iowa in recent years on carbonate aggregate reactions in concrete. Groups outside the state have become active in the past few years after recognizing that certain carbonate aggregates are reactive in concrete. The paper reviews the nature and extent of the problem and a summary is given of research by the author and his associates. In recent years considerable research has been conducted in Iowa on carbonate aggregate reactions in concrete. The research is part of a general study on the behavior of carbonate rocks as concrete aggregates sponsored by the Iowa State Highway Commission. Research on carbonate aggregates has not been extensive in the past. Laughlin1 published one of the first papers on carbonate aggregates in 1928 and was followed by others, notably H. S. sweet,&apos; B. Mather et al.,3 and K. Mather4 who emphasized the petrographic and physical aspects of carbonate aggregates. The recognition that certain carbonate aggregates are reactive in concrete has led to increased participation in research in the past few years by groups outside of Iowa. Significant contributions have been made by Swenson and Gillot,5 Hadley,6 and Chaiken and Halstead7 in work which emphasizes the expansion of carbonate rocks in alkaline environments and the reaction of carbonate minerals or dedolomitization with alkalies. It is the purpose of this paper to review briefly the nature and extent of the problem and present a summary of the research by the author and his associates. EXTENT AND NATURE OF THE PROBLEM The problem is the deleterious behavior of certain carbonate aggregates in concrete. It was first recognized in Iowa over 20 years ago when poor service records of certain highways were correlated with aggregates produced from the Glory and LeGrand quarries. Deleterious behavior of carbonate aggregates have been reported in Canada and, more recently, in New York and Virginia. As more knowledge is gained concerning the problem, distress in concrete related to carbonate aggregates may be recognized over a widespread area. The problem may potentially exist in the Midwest, the Northeast, and other parts of the country underlain by thick sections of carbonate rocks readily available for utilization as aggregates. The nature of distress in Iowa highways is a general weakening and deterioration of concrete characterized by progressive cracking and spalling away from joints and edges (Fig. 1). The distress generally occurs after 15 years of service and becomes progressively worse. Specimens of such concrete lack the toughness of sound concrete and break easily under the hammer in the manner of a soft brick. The matrix is generally highly carbonated and dark borders, or reaction shells or rims outline the argillaceous carbonate aggregate fragments (Fig. 2). Cracks observed in cores cut across the aggregates and concrete matrix. Although localized volume change (expansion) is associated with spalling, there is no definite field evidence in Iowa that excessive growth of concrete slabs has occurred. The experience with carbonate aggregates in Iowa indicates that the concrete deterioration is not the same as that induced by the alkali-aggregate reaction associated with siliceous aggregates. The principal difference is that in Iowa the distressed concrete is weakened throughout the slab. In concrete affected by the alkali aggregate reaction, the

Jan 1, 1961

By H. A. Fisch, A. J. Opinsky, J. L. Bartos

Fort?-six- two-grain bounduries were studied in doped tungsten 1amp wire that had been heated to 3450°K very vapidly. Back-reflection Laue photograms were taken of the grain boundary partners and solved, using a computer. The resulting distribution of large-grain orientations was analyzed. Rotational axes were calculatedfor each grain boundary pair. The axes of least rotation show an anisotropy of rolalional angle. WhILE the orientations of large grains in straight doped tungsten wire have been studied extensively, little has been done to characterize the boundary that separates them. Rosi.1 upon seeing the jagged interlocking boundary in doped tungsten wire. inferred that the grains should have a preferred orientation, and proved it. He interprets his data as indicative of a single ideal orientation—(531)— being parallel to the wire axis. Rieck2, 3 and Mannerkoski&apos; have essentially confirmed this finding. Opinsky, Orehotsky, and Siegle argue that the data suggest that (211)—a plane-is parallel to the wire axis instead. This (211 ) contains the (531). and hence would appear to be a more general case.5 Ahlborn and wasserman6 report that their orientation data stretch from (110) through (531) to (311). This path is the locus of {211 Recently. Opinsky has suggested that the data can be interpreted as a series of ideal orientations that can be related by coincidence relationships to the (110) fiber texture. All these investigators have determined the orientations of the large grains by the back-reflection Laue technique, and they have all obtained similar results. Only Rieck5 as methodically looked at the large grains along a wire. He was apparently not concerned with the relationships of the large grains across their common boundary, but only with their individual orientations. This research was undertaken to fill this gap in the under standing of the mechanical properties of tungsten wire. Only the crystallographic aspects of the problem will be reported here. In addition, the large number of large-grain orientations, which was accumulated in this study. will also be analyzed. EXPERIMENTAL MATERIAL AND TECHNIQUES All of the data were obtained from four pieces of the same 7-mil-diam General Electric tungsten lamp wire. Twelve-inch lengths of the cleaned wire were heated in vacuum by the flick of a switch to 90 pct of the amperes necessary for fusion (a temperature of approximately 3450°K) and held for 1 min. On the basis of other data. it is estimated that the rise time is of the order of 0.5 sec. The four pieces of wire could have come from anywhere within about 18 ft of wire. Consecutive segments of each piece of wire were mounted in bakelite and polished metallographically The polishing procedure followed that described by woods. "nly boundaries between two grains that each occupied the entire cross section of the wire were photographed and X-rayed. The metallographic sample was mounted accurately with respect to the X-ray unit. Steps were taken to read the films as accurately as possible with the conventional Greninger net. The data were then entered into computer programs that solve the Laue film by precisely the same techniques that are used in the solution of the film by means of the stereographic projection. The use of the computer has probably shifted the main source of error from the stereographic plot to the reading of the film. On the basis of several experiments, it is thought that the error associated with the entire process, from mounting the sample through the computer solution, is of the order of about one-half degree. The output of the computer is the direction cosines of the fiducial direction (the wire axis) and the locations of the three cube axes. The former data were used to calculate the differences in orientation between the two grain boundary partners, and the latter were used in the calculation of the rotational axes that could bring the two grains

Jan 1, 1970

By C. N. Reid

Slip-line studies on deformed chromium single cvystals showed the usual bcc behavior. At room temperatuve, cross slip was prevalent—slip was not confined to a given plane, but the slip direction was (111). At -10O0K, slip occuvred on (110) planes, twins on(112) planes, and cleavage on (1001 planes. A single-crystal tensile specimen with an axis close to [011] showed a pronounced yield drop and high strain rate sensitivity which zclere used to derive relevant parame tevs in a dislocation dynamics treatment. Transmission electron microscope studies confirmed the existence of (110) slip planes and showed ecidence of loops punched out by precipitates and of grown-in dislocations promoting tangling. OF recent years experimental studies have been made of the deformation characteristics of single-crystal molybdenum and tungsten, but very little has been published on the behavior of single-crystal chromium. During a study of the mechanical properties of chromium, single-crystal studies were made which have already been partially described.&apos; However, additional information was generated which was not directly relevant to the main theme of Ref. 1, and, therefore, was not reported. In view of the need for complete documentation of deformation modes, the experimental observations made on the deformation of single-crystal chromium are summarized here, together with an electron-microscope study of the associated dislocation structures. It was found that, in terms of the deformation modes, chromium is a conventional bcc metal, showing a very pronounced yield-point phenomenon. Further, it was found that the flow strength of these crystals is very sensitive to the strain rate. Finally, the crystals were observed to contain many unidentified precipitates, which often were associated with prismatic dislocation loops. EXPERIMENTAL METHODS Single crystals were grown from rods of wrought chromium by the method of zone annealing. Rods of "1/4in.-diam were supported vertically in an argon atmosphere while an induction coil was moved up the rod at 1 in. per hr. The power was adjusted to just below that required for melting, and the process produced single crystals in about 30 pct of the rods used. The orientations of the crystals, in general, lay near [011] and are summarized in Fig. 1. Before this treatment, the wrought material contained 35 pprn C, 68 ppm O, and 12 ppm N.* An analyzed single crystal *Usual metallic impurities found in iodide chromium are: Al, 5 ppm; Ca, A ppm; Cu, 2 ppm; Fe, 75 ppm; Yg, 0.5 ppm; Yn, < 3 ppm; Mo, < 3 ppm; Ni, 4 ppm; Si, < 20 ppm; Ti, < 1 ppm; V, 4 ppm; Zr, < 3 ppm. contained 10 pprn C, 79 ppm O, and 50 pprn N. Tension and compression specimens were shaped from the crystals by mechanical grinding, followed by the electrolytic removal of about 0.010 in. from the surface in a perchloric/acetic acid bath. All specimens had a gage length of 0.75 in., and tension specimens had a diameter of 0.100 in., while that of the compression samples was 0.200 in. Mechanical tests were carried out at a rate of 1.3 pct per min, and temperatures below 0°C were attained by means of a nitrogen cryostat similar to that of Wessel.2 EXPERIMENTAL RESULTS Modes of Deformation. In addition to the tensile properties of these crystals, which are described in Ref. 1, deformation markings on the surface were studied. Crystals A and F, Fig. 1, were deformed in tension at 300°K to 10 and 16 pct strain, respectively. The surfaces contained visible slip lines, about 1 C( apart, composed of both straight and wavy segments. They did not define a single plane, and so determination of the slip plane was not possible. However, the slip direction was deduced by comparing the axial orientations of the crystals before and after deformation. Fig. 2 is representative, and shows that the axis ro-

Jan 1, 1968

R. E. Powers (Mellon Institute of lndustrial Research, University of Pittsburgh, Pittsburgh)—Several of the processing methods at the Josephtown smelter might well be considered by plants producing iron blast furnace sinter. In making blast furnace sinter the objectives are much the same as at Josephtown: To produce a strong yet porous agglomerate which has a size consist in a preferred range. The emphasis however is on production rate rather than on the size or other quality characteristics of the sinter. Therefore the technique is entirely different. Blast furnace sinter plants attempt to make their product in one pass with a minimum recirculating load and without sizing treatment after the sinter leaves the machines. Many plants are beginning to feel that more attention paid to quality characteristics would make the product a more desirable blast furnace material. The pelletizing of very fine material before placing it on the bed is not deliberately done at iron sinter plants, although the installed equipment sometimes gives a simila; action. Such pelletizing seems to be a promising way of accommodating the down-draft sintering Drocess to very fine materials. he recirculating load at Josephtown is extremely high. Two plants&apos; producing blast furnace sinter from raw material of comparable size have a recirculating load of about 100 pct of production. At Josephtown it is notable that the size and the rate of feeding of return fines are under control. This is not the case in most blast furnace sinter plants. The sinter slicer appears to be a worthwhile aid in effecting such control. It is similar in action to rakes and plows used at a number of plants, but it has the advantage that the sinter dislodged is positively removed and not left to the inefficient action of a stationary grizzly screen. Blast furnace size specifications for sinter are not at present so rigid as the Josephtown specifications. If the sizing of blast furnace sinter does become important, then the Josephtown crushing practice, in which a large recirculating load is maintained on the crusher in order that minimum fines be produced, may be of interest. H. K. Najarian (authors&apos; reply)—We note that Mr. Powers appreciates some points that we tried to emphasize in our paper as being of importance in making zinc sinter of good quality and which may well be applied to iron blast furnace sinter. Fig. 2 shows the pelletized nature of the feed going on to a Dwight-Lloyd type sintering machine in our plant. Practically, the entire feed consists of more ,or less rounded particles which permit more uniform air passage through the charge, while the larger particles in the charge roll on to the surface of the grate, which helps to keep the grate openings from being clogged by excessive fines. An agglomerated charge of this character may preferably be made by rolling action while being mixed in a rotating drum and wetted by water sprays to bind the fine particles together and give the charge the desired moisture content. From our observations of several iron ore and blast furnace flue dust sintering operations, we believe that if the fines from the sinter discharged from the machines were to be recirculated and agqlomerated with the new feed, not only sinter of better quality but larger capacity from the machines may be realized.

Jan 1, 1952