Search Documents

By W. L. Fink, L. A. Willey

DURING the war there was introduced a new higher strength aircraft alloy designated 75S.1,2.3 The properties of this alloy assure extensive applications in both military and commercial aircraft. It is therefore important to understand its limitations as well as advantages. The properties of 75S alloy in the heat-treated tempers, like those of many other aluminum alloys, are affected by the rate of quenching. In general, low quenching rates tend to cause low strengths and to adversely affect the resistance to corrosion. Commercial quenching procedures are usually sufficiently rapid to permit the development of maximum properties. However, in the center of heavy sections, such as large rolled and extruded shapes, the quenching rates may not be rapid enough to develop maximum strength or resistance to corrosion. The investigations of 75S alloy described herein reveal the most critical range of temperature and the effects of quenching sheet and extrusions at different rates through that temperature range, on the tensile properties and resistance to corrosion. PROCEDURE Preparation of Specimens Sheet specimens (3 in. by 9 in.) were prepared from a commercial lot of 75S "as rolled" sheet (0.064 in. thick). The composition° was as follows: Weight Percentage Cu Mn Mg Zn Cr Al with Normal Impurities 1.64 0.16 2.58 5.66 0.27 Remainder The specimens employed for the determination of the time-temperature relations during quenching of sheet were prepared by the following procedure: the hot junction of a 28-ga. iron-constantan thermoelement (asbestos insulated) was brazed to a thin strip of aluminum which was in turn brazed into the end of a 3/16 in. i.d. by ¼ -in. o.d. by 30 in. long aluminum protection tube. Before brazing, the tube was flattened to 0.064 in. thickness over the junction and adjacent lead wires for a distance of 1 ½ in. The flattened end of the tube was fitted into a slot cut from one edge to the center of the 3 in. by 9 in. by 0.064 in. sheet and brazed into place. The brazed joint was dressed to the thickness of the sheet and the entire specimen buffed to approximately the brightness of "as rolled" material. Because of the brazing operations required, these specimens were prepared using 3S alloy. For the investigation of quenching rates in heavy sections, there were used 75S extrusions which had compositions similar to that of the sheet. The specimens consisted of 14 in. lengths of ¾ in., 2 in., 3 in. and 4 in. diam cylindrical rods and a roughly rectangular extruded section which was approximately 4 in. by 7 ½ in. Thermocouples were peened into the bottoms of 1/8 in. diam wells drilled into one end and parallel to the axis to a depth of

Jan 1, 1947

By A. A. Smith, J. S. Smart

THE controlled amounts of phosphorus, arsenic, sulphur or selenium found in commercial coppers perform a variety of highly useful functions. Indeed, a large segment of modem copper technology is essentially dependent upon the presence of one or more of these elements. Consequently, the literature contains many references to their effects but the scope is broad and has been only partly covered. New data are presented herewith directed toward a better understanding of the basic behavior of these elements in copper, with particular emphasis on the composition range 0 to 0.05 per cent. These data are a part of a general program of research on the effects of impurities on the properties of oxygen-bearing and oxygen-free copper, other portions of which have been reported previously.1-2-3 Schematically, the behavior of individual elements is determined from measurements of conductivity and softening temperature,1, 2 and the binary alloys employed are synthesized from high-purity copper in order to eliminate interference from the effects of extraneous impurities. Alloys of selected composition were first prepared in the oxygen-free form by continuously casting the melts in the form of 3/8-in. diameter rod. Oxygen was added subsequently to portions of the alloys, either by remelting or by diffusion at 850°C. from a surface scale. Test wires were drawn one B. and S. number per pass, using four 30-min. 600°C. anneals at o.3125, 0.257, o.204 and o.162 in., and a final cold reduction of 95 per cent t0 0.081 in. Oxygen-bearing slugs made by remelting were hot-rolled to 5/16 in., drawn to 0.162 in., annealed for 30 min. at 600°C. and cold-drawn 95 per cent to 0.081inch. The alloys containing phosphorus, having been compounded very early in the program, were prepared in the form of 5/16-in. rod, and processed to wire with only the last three intermediate anneals listed above, all of these having been conducted in commercial nitrogen. In addition, the conductivity anneals on these alloys were also performed in the same atmosphere, and the small amount of oxygen present as an impurity in the gas resulted in some loss of accuracy at temperatures of 700° to 800°C., as will be shown later. Subsequently, the anneals for all oxygen-free alloys were conducted in hydrogen to prevent oxidation, and purified nitrogen was employed only for oxygen-bearing samples. All conductivity anneals were of one hour duration followed by a rapid quench in 10 per cent H2SO4. EFFECT OF PHOSPHORUS The widespread use of phosphorus as a deoxidant has resulted in universal appreci-

Jan 1, 1945

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,' of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in terms of mass per unit time by w Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L Slope of energy grade line by s Mass per unit volume of solids by m8. Mass per unit volume of liquid by mi Mass per unit volume of mixture by 11 We then have as an expression for the solids load: w = pqmm The work done per unit mass, p, on the mixture to move it along the pipe the

Jan 1, 1947

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,' of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in terms of mass per unit time by w Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L Slope of energy grade line by s Mass per unit volume of solids by m8. Mass per unit volume of liquid by mi Mass per unit volume of mixture by 11 We then have as an expression for the solids load: w = pqmm The work done per unit mass, p, on the mixture to move it along the pipe the

Jan 1, 1947

By John L. Schroder, Woods G. Talman

EXPERIENCE has shown that certain known natural conditions and other indefinite characteristics combine to make a mining area vulnerable to mountain bumps. Some of the known conditions are heavy overburden, an overlying stratum of strong non-elastic rock, a structurally strong coal seam that does not crush easily and yet is the weakest stratum in the series, and a floor stratum of more than ordinary firmness. The indefinite characteristics could include resistance of top or bottom of a coal seam to lateral flow, effect of immediate top and bottom strata, nature of the coal seam, and other factors about which very little is known. It is in this area that exhaustive study is needed to achieve positive control of the dreaded mountain bump hazard.

Jan 8, 1958

By Shun-ichi Satoh

Studies by many authorities have proved that nitrogen exerts an injurious influence upon iron and steel, but in the casehardening of steel by carbon, nitrogen has the advantage of accelerating the process of cementation. Its influence upon special steels is quite remarkable; it can produce the hardest layer ever known in metallurgical products—a fact hit upon by A. Fry and studied and ascertained by L. Guillet. As there have been very few investigations on the influence of nitrogen on special steels, the writer has listed important articles dealing with this problem and has conducted experiments on nitrification. He also has tested the influence of nickel upon the penetration of nitrogen in electric-arc welding. Nitrogen Process for Surface Hardening In 1919, Siegmonl conducted an experiment known as "Versticken" by treating steel with ammonia gas and found that the steel thus treated has the properties of resisting corrosion. In 1922, L. E. Benson3 nitro-genized iron and steel by sodium nitrate. Fry3-"studied the nitrogen process for surface hardening and published the results of his studies in 1923, 1924 and 1926. Guillet tested special steels containing various elements with the current of ammonia at 500' to 510' C.10, 11, 12, and determined the hardness of some of them at various temperatures.13 He also conducted corrosion tests14 in 1927. Fry15 stated that tinplat-ing could prevent nitrogen from penetrating into steel in the course of nitrification. In 1927, Guillet 65 described the historical notes of the nitrification; and many applications of nitrification were published in the Kruppsche Monatshefte.51, 59, 62, 63, 64-74~75 H. K. Herschman66 conducted the wear test of the nitrified steel. Gunnar Hägg investigated

Jan 1, 1930

By B. R. Coil

One executive writing on capital equipment re- placement stated: "We keep extremely close watch over repair costs and when we reach the point of uneconomical operation, we replace the machine." This, of course, is most elementary, but a very basic premise. However, it seems advisable to set forth several equally obvious principles, so that all discussion will start from the same point. The subject is intended to deal with the point of uneconomical operation due to high operating costs in general and high repair costs in particular. This is not concerned with a similar problem of high costs because of an insufficient number of machines, be they trucks, shovels, or dozers.

Oct 1, 1955

By Fred C. Bond

Many grindability tests have been made in the Allis-Chalmers laboratory since the tabulated results were last published.' The lists of standard ball-mill and standard rod-mill grindability tests are brought up to date in this paper, and considerable new material is added. This includes a tabulation of open-circuit grinding tests, with impact and compression-crushing tests. The standard ball-mill grindability tests (Table I) were made in a standard laboratory ball mill, 12 by 12 in. inside, running at 70 rpm, with a charge of 285 iron balls ranging from 1½ to 3/4 in. in diameter and weighing 20,125 grams. Seven hundred cubic centimeters of minus 6-mesh stage-crushed dry feed was used, and the circulating load was maintained constant at 250 pct by adjusting the number of mill revolutions for each grinding period. Tests were made at all mesh sizes from 28 to 200, and the grindability is the number of net grams of screen undersize produced per revolution. The table includes 479 tests. It has been calculated that the ball mill does 52.3 joules of useful work on the ore per revolution2 with 93 joules input to the mill. The standard rod-mill grindability tests (Table 2) were made in a laboratory tilting rod mill, 12 in. in diameter by 24 in. long inside, with a wave-type lining, running at 46 rpm. The grinding charge consisted of six I1/4-in. diameter and two 13/4-in. diameter steel rods, all 21 in. long and weighing 33,380 grams. The mill was rotated level for eight revolutions, then tilted up 5' for one revolution, down 5° for one revolution, and returned to level for eight revolutions. It was discharged by tilting downward at 45° for 30 revolutions. Feed consisted of 1250 cc of minus in. stone and the circulating load was maintained constant at 100 pct by adjusting the number of mill revolutions for each grinding period. Tests were made at all mesh sizes from 3 to 65, and the rod-mill grindability is the number of net grams of screen undersize produced per revolution. The table includes 105 tests. The impact and compression-crushing tests (Table 3) are given in a table that is an extension of a previous publication8 in which the method of testing was described in detail. Two equal hammers weighing about 30 lb each were arranged to strike simultaneous blows on opposite sides of the test specimen. Broken pieces of rock passing a 3-in. square and retained on a 2-in. square were set up with the smallest dimension between the hammers, and this distance was measured. The height of the hammers was increased slightly before each blow until the specimen broke, and the foot-pounds per inch of thickness was calculated. Ten pieces

Jan 1, 1949

By R. G. Ward

The temperature gradient in the subhearth metal or "salamandern of the iron bhst furnace results in the establishment of gradients in the concentrations of silicon, manganese, carbon, and sulfur. The temperature and compositional variations observed in three blast furnaces are analyzed according to irreversible thermodynamics and the systems appear to be close to the steady state condition. Apparent heats of transport, Q, for silicon, manganese, carbon, and sulfur are found to be respectively -17.5, -5, -2.1, and+22k cal per g mol. In conclusion the significance of thermal diffusion in extraction metallurgy is briefly discussed. INCREASING interest has been shown in recent years in the application of irreversible thermodynamics to metallurgical problems. In particular studies have been made of the transport of matter in thermal gradients1-' and under chemical gradients imposed by a binary solvent However, no detailed example in extraction metallurgy has been reported although gradients are the essence of many extractive processes. The case of the distribution of elements in molten blast furnace iron under a thermal gradient is discussed here. DATA In blast furnace operation the hearth bottom is often extensively destroyed by molten metal, and the metal may penetrate perhaps 10 ft into the furnace foundations forming a "bear" or "salamander". Several hundred tons of molten metal may thus exist beneath the level of the conventional tap hole and remain relatively undisturbed for several years under a thermal gradient. This system is subject to little convective stirring because the temperature decreases from top to bottom, and mechanical stirring due to movements in the stack and to tapping operations is unlikely to penetrate far into the metal. The system may thus be regarded as static

Jan 1, 1963

By Charteris A. Stewart

The following scanty notes on the Roumanian oil-region may serve as an introduction to more detailed future study and description. The Roumanian oil-belt follows the outer edge of the sweep of the Carpathian mountains, and may, in a broad sense, be regarded as a prolongation of the Galician belt. It is distributed over a tract of country from 300 to 400 miles in length, with a width of from 15 to 20 miles, and is believed to cover an area of at least 20,000 hectares (49,420 acres). The governmerit claims that 16,000 to 17,000 hectares of its land is petroliferous. The primary deposits of petroleum arc considered to be in the Paleogene (Oligocene) and the Neogene (the salines of the Miocene) formations. Most of the other repositories, especially those of Muntenie, are only secondary, the petroleum there having been introduced by the orogenic movements which raised the Carpathian mountains. The oil-field has been divided by the Roumanian Survey into two regions, the Flysch and the Sub-carpathian, as is shown in the accompanying sketch-map, Fig. 1. So far as is yet known, practically all the seepages and productive pits and wells are situated on anticlinals. Those which outcrop in the Flysch region (called Paleogene anticlinals), as indicated in the sketch-map, Fig. 1,are : Solontz,

Jan 1, 1907

By A. U. Seybol

Eight binary iron alloys were examined after ion nitriding experiments to determine the behavior of the following elements: Al, Mo, Mn, Si, Ti, V,Cr, and C. Only Al, Cr, Ti, and V additions caused hardening in binary iron alloys. A few steels were examined to see the effect of Cr, Cr + Al, Cr + Ti, and Cr + V. It is suggested that a useful new class of ni-triding grade steels might be those containing about I pct V. The nitriding of steel, first described by Fry1 about 45 years ago, rapidly attained commercial application with very little knowledge of the fundamentals involved. While Fry,' in describing the status of nitriding in 1932, apparently correctly postulated hardening by precipitated nitrides, the details of the nitriding process were not understood, nor has the situation changed much since that time. It is also interesting to note that the compositions of some typical nitriding steels given by Fry at that time have changed little in the intervening years. Currently used nitriding steels owe their surface hardening to either chromium (as in 4340 steel) or aluminum plus chromium as in the Nitralloy grades, where both CrN and AlN appear to contribute to harden ing. Titanium additions have been studied experimentally, but thus far titanium steels have not won wide commercial acceptance. This subject will be expanded later. The orthodox ammonia nitriding process has been reviewed very adequately many times as in Jenkins3 and Case and VanHorn,4 and their is no need to outline the process here. Ion nitriding is not as well-known, although there have been several descriptions5-9 of the process given, sometimes with comparisons with the ammonia process. Most of these papers are primarily concerned with a description of the equipment, or of the physics or electrical engineering aspects of ion nitriding, but Noren and Kindbom9 gave the results of a metallurgical investigation using both processes. In brief, ion nitriding is carried out in a vacuum chamber from which the air is exhausted and replaced by a N2-H2 mixture, typically containing 10 to 20 pct N2, at about 5 to 10 torr pressure. While ammonia gas has also been used in ion nitriding, there is no evidence that ammonia makes any improvement in the ion nitriding process. A few hundred volts dc is applied between the grounded container wall (positive) and an insulated center post supporting the work (negative) to be nitrided. A glow discharge is created in the ionized gas, accelerating positive nitrogen ions to the work. These ions contain enough energy to form the normally unstable Fe4N "white layer", thus establish- ing surface nitrogen solubility characteristic of the a Fe/Fe4N equilibrium. This creates a substantial concentration gradient, driving dissolved nitrogen into the steel. The temperature employed is in the same range (around 500" to 550°C) as in ammonia nitriding, but because of factors which are not understood at present the nitriding time is ordinarily considerably reduced in ion nitriding. Other advantages have been cited,9 but it is not the purpose of the present work to contrast the two processes. The present objective was to examine the behavior of binary iron alloys during ion nitriding with respect to the microstructure, hardness level, and depth, and to examine some of these factors in steels as well. In this way it was hoped to be able to find out something about the individual role of these elements in steels. While all the work was done by ion nitriding, there seems to be no reason why any conclusions reached would not equally apply to ammonia nitriding, excepting only the kinetic aspects of the process. Another objective was an exploration of the critical-ity of the ion nitriding variables: gas composition, pressure, temperature, and time. EQUIPMENT AND MATERIALS The equipment used was substantially as described by Jones and Martin.8 The vacuum tank was about 12 in. in diam by about 18 in. high, and consisted of water-cooled stainless steel, with a single small window at the top for viewing inside. This sat on a heavy mild steel base equipped with the main pumping port, pressure control port, and vacuum gaging. A series of variable resistances was interposed between the glow discharge and a large-capacity -40 amp variable primary transformer feeding a 1000-v transformer, but 600 v were about the maximum ordinarily used. With the small l-in.-round, 4-in.-thick discs used for nitriding, the electrical load was usually about 500 v at 0.8 amp. The specimen temperature was controlled by a stainless-steel sheathed chromel-alumel couple, whose junction was in the steel stool upon which the flat discs were placed. These were ground through 400 Sic paper. Cycling of the temperature controller caused -0.2 amp variation in ion current, providing an ample control band. The binary iron alloys were made from vacuum-melted hydrogen-deoxidized electrolytic iron and alloys of 99.9 pct purity. Cast ll-lb-square tapered ingots were forged and hot-rolled to about 11/4-in.-diam rounds. Discs of 1/4 in. thickness by about 1 in. diam were machined from the rods for nitriding specimens. The following alloys were prepared: 1 pct each of Mn, Mo, Cr, Ti, Al, V, Si, and an Fe-0.8 pct C alloy. EXPERIMENTAL VARIABLES Of the variables total gas pressure, nitrogen partial pressure, temperature, and time, only nitrogen partial pressure was found to be critical to the operation. A critical nitrogen partial pressure was found corre-

Jan 1, 1970

By Magnus Troilius

For some time I have been using with great advantage, for the purpose of determining rapidly and accurately the chemical composition of gases from Siemens producers, an apparatus arranged generally like that proposed by Prof. Eggertz; * and I now take pleasure in laying before the members of the Institute a description of the apparatus and its use, hoping that some of them may find it. of practical advantage. At the end of the paper are given some results obtained and heat calculations, with the necessary data for the same. COLLECTION OF GASES. Fig. 1. Shows the arrangement for taking a sample of gas. The funnel F, which may be made of tin plate, is made to fit the test-hole. The gas passes up through the funnel and through the rubber-tubing with the glass tube K, filled with asbestos for retaining dust,, and is drawn into the upper flask by means of water flowing from the same into the lower flask. The upper flask must be completely filled with water from the beginning, so that no air remains. When filled with gas the screw-compressors are securely fastened on, and the flask disconnected from the funnel and receiver. Quart flasks, with openings at the bottom, are very suitable, and easily obtainable. COMPOSITION OF THE GASES. The ingredients found in producer gases are: carbonic acid (CO2), oxygen (0)) ethylene (C2H4), carbonic oxide (CO), hydrogen (H), and marsh gas (CH4). The nitrogen is taken by difference. CO2,O,C2H4, and CO are determined by absorption in various liquids and by observing the resulting diminution of volume. H and CH4 are determined by combustion with oxygen. Carbonic acid.—For this gas is used a solution of 16 grams of potassium hydrate in 100 C.C. of water. 4 or 5 C.C. of this solution absorb 100 C.C. of CO2.

Jan 1, 1883

By D. R. Irving

Prior to this time, ample supplies of high grade mineral fillers, such as clay, have been available close to consuming centers. Now depletion of these accessible deposits, coupled with other factors such as increasing demand due to population expansion and standard of living rise, has made development of upgrading techniques attractive to producers. Various investigations being carried out by the U.S. Bureau of Mines are described. Factors making the development of improved methods for upgrading clays attractive to producers include: depletion of accessible deposits of high-grade clays, rising transportation and labor costs, more exacting specifications, and increased demand resulting from an expanding population and a constantly rising standard of living. Industry recognizes the need for upgrading presently unusable materials and has cooperated with the U.S. Bureau of Mines by providing samples from submarginal deposits and by evaluating the products that USBM upgrades. Following are some examples of recent clay beneficiation work by the Bureau. FIRE CLAY BENEFICIATION At the Rolla Metallurgical Center, Rolla, Mo., the Bureau is conducting research to develop technically and economically feasible mineral-dressing methods to remove quartz, pyrite, and other impurities from submarginal fire clays. The research has been spurred by the growing shortage of high-grade bur-ley, flint, and plastic clays in the Missouri fire-clay district resulting from increased consumption and the low rate of discovery of new deposits of adequate quality. There apparently is ample tonnage of submarginal flint and plastic clays to maintain the industry for many years if such material can be upgraded to commercial quality. Samples have been submitted to USBM by several major producers of refractories, including A. P. Green Fire Brick Co.; Harbison-Walker Refractories Co.; Mexico Refractories Div., Kaiser Aluminum and Chemical Corp.; and Wellsville Fire Brick Co. Research on some samples has been completed and still is in progress on others. The Bureau has found that specimens containing quartz or pyrite in grains coarser than the accompanying clay generally can be upgraded either with a gravity table or hydraulic cyclone. The improvement in quality is notable not only in chemical analysis but in an increase in pyrometric cone equivalent (PCE) of one or more cones. As an example, consider the results attained on a sandy flint—a fine-grained mixture of kaolin and halloysite with quartz and minor quantities of iron and manganese oxides. Chemical analysis was: 35.4 pct alumina (A12O3) and 47.8 pct silica (SiO2). The sample contained 9.2 pct free silica as quartz. The PCE was 33. The sample was crushed to -10-mesh, blunged with water, and then stage-ground to -48-mesh. The ground sample was tabled to yield a clay fraction containing 37.6 pct A12O3, and 45.3 pct SiO2 of which 2.4 pct was free silica. The PCE was 34. Recovery of alumina by this process was 73.6 pct. Concentration of the same clay in the hydraulic cyclone was even more effective in respect to quartz removal. The clay fraction analyzed 38.6 pct A12O3, 45.0 pct SiO2 of which 0.5 pct was free silica as quartz, and had a PCE of 34. Recovery of alumina was 71.9 pct. The hydraulic cyclone was also effective in reducing the pyrite content of a plastic clay which likewise was a mixture of kaolin and halloysite, plus some pyrite, quartz, and carbonaceous material. It analyzed 30.6 pct Al2O3, 52.3 pct SiO2, 2.3 pct Fe2O3, and 0.76 pct S. The sample was blunged and screened through 10-mesh to remove some coarse pyrite, then ground to -65-mesh and cycloned to remove most of the remainder. The final product recovered 81.8 pct of the alumina at a grade of 32.3 pct A12O3, 50.9 pct SiO2, 1.4 pct Fe2O3, and 0.1 pct S. The PCE was 32-1/2, compared with a PCE of 31-1/2 for the crude clay. The fine beneficiated clays, of course, must be pelletized and dried or fired to meet commercial acceptance. This operation has already been solved by industry. Little progress has been made on two remaining problems. One is that of fine-grained impurities, not separable by table or cyclone. Flotation is being investigated to solve this. Although fine pyrite is readily rejected, a satisfactory quartz-clay separation has not been attained. The second problem, a stubborn one, is that of alkali. Samples containing as much as 5 pct potas-

Jan 1, 1961

By Robert Glass Cleland

THE OUTBREAK of World War II found Phelps Dodge, thanks to both foresight and good fortune, in a position to increase production of its mines and factories to meet the insatiable military and domestic needs of the times, far beyond all previous records. With the timely completion of the expansion program at Morenci, the company's copper output rose to approximately 447 million pounds in 1942 and to over 478 mil- lion pounds the next year, compared to some 300 million pounds in 1939. To meet the civil and military needs for fabricated cop- per products, the Phelps Dodge Copper Products Corporation carried out an expansion program comparable in size to that of the Phelps Dodge mining operations. It built new plants, enlarged and reorganized those already in operation, multiplied the number of technical experts on its staff, adopted new methods and new machines for the new prod-

Jan 1, 1952

By John C. Holtz

Hostility is a characteristic of the environment in underground mines. Nature opposes man's efforts to remove mineral deposits, and this condition is recognized when mining is described as winning minerals from the earth. Evidence of this conflict is the action of natural forces to close excavated passageways. In many mines, this behavior of the surrounding environment is an ever-present and ever-changing problem despite much research and empirical study. Geological conditions change abruptly and may result in rock bursts, the inrush of water, or variations in rock hardness. Although aspects of these problems will become intensified as the rate of mining increases, they are not considered in this discussion. Emphasis herein will be on the changes in the atmospheric environment. Men underground work in an ever-changing, alien, ambient atmosphere. Many conditions are encountered that will affect their health and safety unless properly controlled. Potentially explosive gases are released from minerals as they are mined or enter from the surrounding earth. Some mining methods generate noxious gases. Natural processes and diesel equipment can steal life-sustaining oxygen. Airborne dust may cause lung diseases when breathed by miners in excessive amounts and by affecting visibility, introduce safety hazards. Deep mines pose heat problems that may be aggravated by high-speed mining. The deleterious effects caused by these changes, and their mitigation, are subjects of this discussion. THE UNDERGROUND ATMOSPHERE Health and safety problems from changes in the underground atmosphere have been apparent since the beginning of mining. Alleviation of these problems has been by ventilation with normal air from the earth's surface that flushes away the vitiated mine atmosphere. The objective is to provide atmospheric conditions essentially similar to those that man is accustomed to on the surface.

Jan 1, 1970

By Woolsey McA. Johnson

Independently of the recognized chemical reactions involved in the production of metallic zinc, the process is affected by physical conditions in efficiency, and by commercial as well as technical economy. To offer some observations concerning these conditions is the purpose of the present paper. Among the important elements of this problem is the physical nature of the particles constituting the mass of zinc oxide to be reduced. This may be the result, either of the manner of the original deposition of the mineral, or of the treatment to which it has been subjected in the roasting-furnace. The physical character of the reducing-agent is another important factor, since the carbon of some coals is much more active in reduction than that of others. The degree of fineness, whether of ore or coal, or both, likewise plays a significant part. These factors, together with the physical admixture of foreign substances with the ore, may give rise also to chemical " side-reactions," sometimes hindering or retarding, and sometimes accelerating, the reduction. Finally, thermal conditions, including the relative conductivity of the materials, deserve to be taken into account. In firing a furnace with retorts charged with a mixture of roasted ore and coal, the first reaction is naturally the boiling-off of the contained water; the next is the distillation of the light hydrocarbons from the coal; the next is the reduction of the iron oxide to protoxide and sub-oxide successively, and then to metallic sponge; and the final reaction is the reduction of the zinc oxide in the ore by the carbon to metallic zinc. This reaction commences at 1,022o to 1,060o C., according to the physical nature and condition of the coal and ore. Since the retort and the charge are far from being good con-

Jan 1, 1908

By R. Schuhmann

PROBLEMS in expressing, interpreting, and using size-distribution data recur in many phases of mineral dressing; therefore it is desirable that size analyses be expressed in such a form, either numerically or graphically, that comparisons can be made readily. The size distribution of comminuted material is a result of a specific physical operation on the material and therefore should be governed by some definite physical principle, or cause-effect relation. Although this principle has not been discovered, it has been found that the size distribution of comminuted, homogeneous solids may be expressed by relatively simple mathematical equations. Two equations in particular, proposed by Gaudin1 and by Rosin and Rammler,2 respectively, have stood out, both having wide demonstrated ranges of application. The form and the method of application of the two appear almost irreconcilably different on the surface, but, as will be shown, they are asymptotic in the fine sizes when expressed in the same units. This paper gives the results of a further study of the Gaudin and Rosin-Rammler relations, made with the object of developing a form of size-distribution equation that will be more usable and more significant-particularly in comminution studies, both for interpreting the nature of size distribution and for evaluating surface. The work is summarized in the following: I. An equation relating cumulative per cent finer to particle size in the fine sizes is derived from Gaudin's original equation. That equation relates weight per cent retained on one size and through the next larger size in a geometric series of sizes to size (of the retaining screen, for example). 2. Comparisons with Gaudin's equation and with the Rosin-Rammler equation show that the cumulative equation applies to the fine sizes of all size distributions that fit either of these earlier relations, and, furthermore, has some advantages over each. 3. A simple graphical method of surface calculation based on the cumulative-equation plot is evolved and illustrated. 4. Additional confirmation of the cumulative equation was obtained in the more severe test of sizing down to the limit of a sedimentation balance a sample of jaw-crushed quartz. The equation was closely followed over a 20o-fold range in size, from approximately 0.4 mm. (35 mesh) down to 0.0023 mm. (2.3 microns), the lower limit of the size analysis made. There is no indication that the equation will not hold further to well below 2.3 microns. 5. Calculations of the surface produced in the jaw-crushing test mentioned above showed that at least 8o per cent of the total new surface was on particles finer than 35 mesh (about ½ 5 of the crusher setting). The minus 35-mesh portion was only

Jan 1, 1940

By G. W. Form, W. A. Spitzig

The effects of hydrogen and vacuum shtering treatments on the physical and mechanical properties of arc plasma-sprayed tungsten were inuestigated. Temperatures examined ranged from 3000" to 4000°F in vacuum and 2000" to 3000°F in hydrogen for both single and duplex sintering cycles. Densities of 92 pct of theoretical density were obtained when a long-time hydrogen treatment at 2000°Fpreceded sintering in vacuum at 4000°F for 4 hr. This cycle also produced the highest ualues for modulus of rupture and bend angle. The results of this investigation point out the desirability of using a low-temperature long-time hydrogen treatment prior to a high-temperature vacuum sinter for arc plasma-sprayed tungsten. ADVANCES in the development of arc plasma-generating equipment have provided a high-temperature heat source that makes the fabrication of tungsten shapes possible by a metallizing process. Tungsten in the as-sprayed condition is very brittle. It has a density between 80 and 85 pct of theoretical density, a lamellar structure with elongated pores, and a high interstitial impurity content. To improve these properties, sintering treatments can be applied to the as-sprayed material, similar to those used for the densification of compacted tungsten powder. However, in view of the differences in the density and microstructure of as-sprayed tungsten as compared with compacted tungsten, responses to sintering were expected to be different. EXPERIMENTAL PROCEDURES The tungsten powder used in this investigation had a particle size varying from 3 to 13 p with an average diameter of 8p. The impurity level was less than 0.1 pct. The arc plasma spraying was done with an F-40 Thermal Dynamics Corp. plasma jet. Spraying was performed in air and thus required cooling of the substrate by an air blast in order to minimize oxidation. The spraying parameters employed in the fabrication of all specimens are listed below: Power input, kw 12 Arc-gas flow, cfh 95N2 + 5H2 Powder feed rate, g per min 33 Powder carrier gas flow, cfh ION, Spray distance, in. 3 Traverse rate, in. per min 30 Mandrel speed, rpm 100 Nozzle orifice, in. 7/32 These values of the spraying parameters correspond to optimum conditions ascertained in a previous study. Sintering was conducted at 3000°, 3500, and 4000°F in vacuum (< 0.1 Hg), and at 2000 and 3000°F in hydrogen. Duplex sintering treatments investigated are listed in Table I together with the designations that will be used for reference throughout this paper. The samples were fabricated by spraying onto a copper mandrel which was removed prior to sintering. The specimens used for the sintering analyses had the shape of small hollow truncated cones 1 in. high with an inside diameter varying from 0.500 to 0.125 in. and a wall thickness of 1/8 in. Specimens for bend testing were taken from hollow hexagonal prisms 1-1/2 in. high with a 1-in. diam across the flats and a wall thickness of 1/8 in. The bend-test specimens were ground to the dimensions 0.085 by 0.350 by 1-1/2 in. Prior to bend testing 0.0025 in. of stock was removed from each surface by electro-polishing. Density measurements were made by the water-displacement method. In addition, a porosimeter was used to determine the amount of interconnected porosity for representative samples. Strength and ductility were determined from recorded values in transverse bending using a cross head speed of 0.020 in. per min. The load was applied at the midpoint of a 1-in. span. The deflection data reported herein refer only to the plastic portion of the total deflection. RESULTS AND DISCUSSION The as-sprayed samples had a density corresponding to 83 pct (l pct) of the theoretical density of tungsten. Fig. 1 shows a representative as-sprayed tungsten structure.

Jan 1, 1964

By Jacques B. Wertz

Even with the best geological maps, there is a constant need for further information and a constant demand for new clues, particularly in exploration work. New ideas and new thoughts are a necessity for progress. In the structural study of an area, be it in Arizona, Africa, or British Columbia, the basic fracture pattern has to be determined first. There is, however, no assurance that the trends shown on the map are really meaningful because they often are secondary in nature, having occurred as a consequence of an intrusion, of doming, or of gravity faulting. Thus, such trends often are a weak basis for assuming the presence of ancient and important zones of fractures that could constitute useful guides to mineral exploration.

Jan 6, 1969

By C. D. Hunter, J. B. Browning

During the year 1934, Kentucky oil and gas operators have partly overcome their past depression fears and in the oil industry, with possibly more abandonments of old oil producers than the completion of new oil wells, produced 4,814,904 bbl. of oil in 1934 against 4,501,511 bbl. in 1933. In the gas industry of eastern Kentucky, 115 gas wells were completed during 1934. This production is delivered through two 20-in., one 16-in., one 12-in., one 10-in., and two 8-in. pipe lines to supply both domestic and industrial markets in Cincinnati, Ohio; Louisville, Lexington, Frankfort, Winchester, Ashland, Covington and other Kentucky towns; Washington, D.C., and other eastern cities. The largest percentage of these gas wells and production are from the Devonian black shale area of Floyd, Pike, Knott, Martin and Magoffin counties, Kentucky. In this area the largest percentage of 1889 wells, developing 421,-215 acres, has been completed in the past 10 years, of which 55.3 per cent produce from the 400 to 550 ft. of Carbonaceous Devonian black shales. The successful results obtained from these Devonian shales are due to the physical effects of the 5000 to 6000 lb. of gelatinated nitroglycerin with which the entire 400 to 550 ft. of shale is shot. A very small number of the shale wells are natural producers and do not require shooting. Other than the Devonian shale gas production, the remaining 44.5 per cent of the gas in this field is encountered throughout the entire strati-graphic section above this horizon; namely, salt sands of Pennsylvanian age and Maxon, Big Lime and Weir of Mississippian Age. A very small percentage is encountered in the Corniferous Devonian lime and the Silurian Big 6 below the black shales. In western Kentucky, in the counties of Henderson, Webster, Hopkins, McLean, Christian, Muhlenburg, Ohio, Daviess, Hancock, Brecken-ridge, Hart, Barren and Warren, many gas wells have been completed, but, because of insufficient market, activity has been somewhat desultory. The area is served by the pipe lilies of the Kentucky Natural Gas Corporation, with headquarters at Owensboro. Their market is increasing and the gas is delivered to Owensboro, Henderson, Madisonville, and many

Jan 1, 1935