Search Documents

By F. O. Garrabrant

Power is furnished to the Climax Molybdenum Co. by the Public Service Co. of Colorado over two 100,000-volt lines to a bank of three 3333-kva. transformers 100/13.8 kv. These transformers are so designed that with the addition of forced cooling their capacity may be increased 331/3 Per cent at 12,000-ft. altitude. Under present conditions, these transformers are operated at 140 per cent of their rating with forced air cooling. On the secondary side of this bank there is a 15-kv., 1200-amp. Westinghouse oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station (Fig. I) where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches.

Jan 1, 1947

By Charles W. Chesterman

Perlite is a glassy volcanic rock which will, upon rapid controlled heating, expand or "pop" into a frothy material of low bulk density, valued as a lightweight aggregate. The term perlite also is applied to the expanded product. The chemical composition of perlite ranges from that of rhyolite to that of andesite; the water content ranges from 2 to 5%. Most perlite is pale gray, but some is black, brown, or even green. Inclusions in perlite are common and include phenocrysts of quartz, feldspar, biotite, and hornblende, and miscellaneous rock fragments. Occurrences of perlite are restricted to areas of Tertiary and Quaternary volcanic rocks. Perlite occurs as flows associated with thick accumulations of pyroclastic debris and other flow rocks, as dikes, sills, domes, and as selvages of intrusive bodies of volcanic rock. Individual flows of perlite range in thickness from a few feet to as much as 100 ft and commonly cover several square miles. Dikes and sills of perlite generally are small, but domes generally are substantial in size and may be as much as several miles in diameter. Most perlite deposits are large enough and topographically situated so as to lend themselves to low-cost open pit mining methods. Conventional equipment is employed in the mining of perlite. Although milling procedures may appear to be simple, care is exercised in order to produce a carefully sized product and to minimize the production of excessive quantities of fine materials, which have limited use and are considered as waste. Perlite is processed, or "popped," in one of two basic types of furnaces: horizontal rotary or vertical stationary. Both types of furnaces include product collection and dust control systems. Many commercial deposits of perlite are known to occur throughout the world, and although no exact estimate of reserves is available, there appears to be an adequate supply to meet current and future worldwide requirements. End Uses The uses of expanded perlite are many and varied and are based primarily upon its physical and chemical properties. Because of its (1) low bulk density, which generally ranges between 2 and 20 lb per cu ft; (2) low thermal conductivity "K" factor (Btu per hr per sq ft per OF per in, of thickness), which ranges between 0.267 for loosely packed perlite (bulk density of 4.48 lb per cu ft) to 1.25 for perlite gypsum plaster; (3) high resistance to fire; and (4) low sound transmission, expanded perlite is used to a great advantage as aggregate and insulating material in the construction industry. Early uses of perlite were related exclusively to the construction industry, which now consumes about 60% of the domestic production. The primary use of perlite now is as aggregate in insulation boards. Other uses of perlite in 1971 were as aggregate for plaster, horticultural aggregate, low-temperature insulation (cryogenics), and concrete. Because of its low thermal conductivity ("K" factor), high adsorption of sound, low bulk density, and fire resistance, perlite aggregate plasters hold many advantages over conventional plaster. Perlite aggregate plaster lends itself to machine applications, dries quickly, and has relatively high elasticity which reduces cracking after drying. These same features make perlite useful as aggregate in portland cement concrete and asphalt concrete for construction wherever weight reduction, insulation, and acoustics are of prime importance. Perlite-portland cement concrete offers up to 20 times more thermal insulation than conventional concrete, and because of this it finds wide application in roof decks and floor fill in multistory buildings, in

Jan 1, 1975

By Wm. E. Milligan

DESPITE the zero weather of Monday, the morning meeting on nonferrous ore-reduction metallurgy got under way promptly under the efficient control of Arthur A. Center. The first and third portions of the paper on the Tri-State region were presented by B. M. O'Harra, with R. H. Lowe substituting for co-author Illidge on the second part. Attention was drawn to the compact design attainable when "Sink and Float" was employed as a means of primary concentration. The teaching profession should welcome this concise correlation of data from such a renowned center of lead and zinc production. H. R. Hanley and C. R. Hay¬ward were much interested in the mechanics of charging, manufacture, and life of the retorts.

Jan 1, 1943

By G. Y. Chin, A. R. Von Neida

The relationship between crystalline texture and magnetic anisotropy in a Co-10 pct Fe alloy has been investigated by means of X-ray pole .figures, hysteresis-loop tracings, and magnetic-torque measurements. The cold-rolled texture of a sample after 95 pct thickness reduction is of the "brass-type", that is, (110)[112/. At 500°C the cold-rolled material recrystallizes fo a (311)[112] orientation, plus a minor (210) [001] component. This texture persists up to 1400°C, at which point it is replaced by a secondary recrystallization texture, (111)[112]. Magnetic-torque measurements show that the easy axis of magnetization lies along the transverse direction in the cold-rolled material and changes to the rolling direction after primary recrystallization. This change is also reflected in the hysteresis characteristic; whereas the B-H loop along the rolling direction is nonsqunre with a low value of residual induction (750 vs 19,000 gauss at saturation) for the cold-rolled material, the annealed sample exhibits a very square loop with a large value of residual induction (16,000 gauss). Theoretical torque curves calculated from the texture data on the basis of magnetocystalline anisotropy energy compare favorably with the observed torque curves. Values of the crystal anisotropy constant, K1, obbained from these comparisons are in good quantitative agreement with single-crystal data. Furthermore, both the torque amplitude of the poly crystalline material and the magnitude of K1 obtained with a single crystal show an identical temperature dependence over the range from —195° 10 +220°C. It is thus conclzided that the magnetocrystalline anisotrpopy erlergy is chiefly I-esponsible. for the nzagnetic allisotropy of textured Co-10 pct Fe alloy. THE results of a study on the relationship between crystalline texture and magnetic anisotropy of an alloy containing 90 pct Co and 10 pct Fe by weight are reported in this paper. The alloy has an fcc structure: a saturation magnetization of about 19,000 gauss,2 and a nearly zero value of magnetoatriction.3 puzey4 has reported a large crystalline anisotropy constant of -7.4 X 105 ergs per cu cm, indicating the (111) directions as the easy axes of magnetization. Hence, texture variations resulting from cold work and annealing are expected to introduce a magnetic anisotropy in the polycrystalline material through the alignment of these (111) easy directions. In the present study, magnetic anisotropy of both rolled and annealed strips was determined by magnetic-torque measurements and hysteresis-loop tracings The results were correlated quantitatively with calculations based on texture data obtained by the X-ray pole-figure technique. It is established that the magnetocrystalline anisotropy energy is indeed chiefly responsible for the magnetic anisotropy of textured Co-10 pct Fe alloy. EXPERIMENTAL Material Preparation. The alloy nominally contained 90 pct Co, 9.5 pct Fe, and 0.5 pct Mn by weight, the chief impurities being nickel, carbon, and silicon (less than 0.5 pct total). The cast ingot was rolled to strips 10 mils thick and slit to 1 in. in width. After strand annealing at 900°C in a hydrogen atmosphere, these strips were further cold-rolled to various thicknesses down to 0.25 mil (97.5 pct reduction), with samples collected for study of the development of texture and magnetic anisotropy as a function of thickness reduction. subsequently, samples cold-rolled from 100 mils to 0.25 mil were obtained, thus extending the thickness reduction range to 99.75 pct. In addition, 0.5-mil samples cold-rolled from 10 mils were selected

Jan 1, 1965

By Albert L. Toenges

COAL mining technique progressed slowly until the advent of mechanized mining. The cutting machine was a forward step, but had only a limited effect upon improving the percentage of coal recovery. Previously, the physical fitness of the loaders and the total output of the miners fixed mine production. The miner was an independent contractor and supervision over his working place was superficial. Rising costs and the inroads of substitute fuels demanded increased output per man to lower the unit production cost. Therefore, the amount of coal loaded mechanically in underground bituminous mines has risen from 0.3 per-cent in 1923 to 7.4 in 1929, to 20.2 in 1937, and to 48.9 percent in 1943. When loading devices were introduced it became necessary to adapt them to existing systems of mining, or to alter the mining system to fit the machine. An increased amount of supervision was required as output depended upon proper operation of the machine rather than on the physical fitness of the individual.

Jan 1, 1946

By Michael A. Arkoosh, E. A. Peretti

ANALYTICAL results have previously been presented for the diffusion-controlled solution of a second phase in a finite medium for planar, cylindrical, and spherical geometries.' These results were obtained by numerical methods using digital computer techniques and are applicable not only to the stage of the problem where the unstable phase shrinks to zero size, but also the subsequent stage where the concentration gradients in the matrix phase become negligible (essentially complete homogenization). It is anticipated that the results of such an analysis may be of use to those workers who are interested in the processes

Jan 1, 1970

By Chester Purington

THE AUTHOR hopes that this paper will meet with criticism and debate by fellow members of the Institute rather than with that attitude of passiv-ity and indifference which one is inclined to adopt when considering a field completely foreign to one's own experi-ence. After several years of study of voluminous literature, maps, and statistics, and many personal journeys and field inspections of various parts of Siberia, the conclusion is reached .that the area adjacent to the Stanovoi, Zhugd-Zhur, and Yablonoi ranges as below defined is that which .is most accessible to the western world and will soonest give results from exploration. HISTORY The first incursion of the Russians into Siberia east of the Yenesei River appears to have been in 1632 when the fort of Yakutsk was founded on the middle Lena. The early expeditions were in quest of furs. As the Siberians say, "the sable beckoned" and the post of Anadyr was founded in 1639, two thousand miles further northeast. Thus nineteen years after the Pilgrims landed in Massachusetts, the Russians had established a trading post within 700 miles of what is now the town of Nome, Alaska. Parties of Cossaks penetrated to the shores of the Okotsk1 Sea early in the seventeenth century, but it was not until 1688 that the town of Okotsk was founded. In 1712 a grand project was elaborated at St. Petersburg for building a port at Okotsk, but it came to nothing. Vitus Bering, the Alaska explorer, built ships at Okotsk, and made this his point of depar-ture. It is stated that the iron work used in these ships was brought overland partly from Yakutsk, and partly even from St. Petersburg, 5500 miles away. Accord-ing to report a copper deposit was worked on the river Urak, not far from the coast, and copper was smelted for sheathing the bottoms. Grassgrown mounds con-taining slag and shots of copper were inspected by the writer last summer, at the site of the ancient shipyard.

Jan 11, 1923

By G. Derge, Ling Yang, John Henderson

Self-diffusion coefficients of aluminum have been measured by the capillary reservoir technique in liquids of the CaO-SiO2-Al2O3 system containirg equimolar portions of CaO and SiO2, in the temperature range 1400o to 1520oC. For the melt containing 6.0 mole pct Al2O3 the results can be expressed by the equation D = [(4.3 * 0.3) x 104] exp [(-85,000 * 17,500)/RT]cm~sec-'; for the melt containing 12.5 mole pct Al2O3, by the equation D = (5.4 i 0.2) exp [(-60,000 * 10,00O)/RT] cm2sec-: A concept of the constitution of these melts has been developed which proposes that the ratios O/(Si +Al) and Al2 O3/CaO determine the dominant species present. In recent years considerable work has been done on the system CaO-SiO2-A12O3 with a view to elucidating the structure of liquids of this system. Conductivity,' electromotive force, 3 density,4 and activity5 measurements have all contributed to an understanding of the problem, but as yet there is no entirely satisfactory theory that can account for all the observed experimental results. In principle, measurements of self-diffusion coefficients should give further information which is not obtainable in other ways. Self-diffusion coefficients for calcium, silicon,6 and oxygen7 have been measured. The present investigation extends the series of self-diffusion coefficient measurements to include aluminum and develops a concept of constitution for liquids of this system which is compatible with all the observed experimental results. EXPERIMENTAL The technique used in the measurement of the self-diffusion coefficient of aluminum was the capillary-reservoir method,8 A126 being incorporated in the melt contained in the capillary and inactive aluminum in the reservoir melt. This method was chosen because it minimizes convection currents' in the diffusion zone. It has the further advantage that the boundary conditions are such that a slight modifica- tion of Anderson and saddington's8 solution of Fick's Law yields an equation which requires measurements only of the length and the initial and final average specific activities of the solidified melt within the capillary. where t is the diffusion time, Co is the average specific activity of the melt contained in the capillary at t = O, C is the average specific activity of the melt contained in the capillary at t = t, 1is the length of the capillary, and D is the self-diffusion coefficient. The equation is of somewhat different form than those previously applied to high temperature diffusion studies because the specific activity of the melt in the reservoir was negligible both before and after diffusion. The diffusion apparatus is shown schematically in Fig. 1. It consisted of a silicon carbide resistance furnace containing the inactive melt in a graphite crucible, internal dimensions 7/8 by 4 in., enclosed in a 1 1/4- by 1 1/2- by 30-in. McDanel tube. A 3/8-in. McDanel thermocouple sheath to which graphite radiation shields and a graphite protection tube were affixed, was used to hold the capillaries. By moving this sheath through a rubber seal at the top of the McDanel tube the capillaries could be lowered into or raised out of the melt. Temperature was measured with a Pt-Pt 13 pct Rh thermocouple which was calibrated periodically against a standard couple. The furnace temperature was controlled to ± 5°C through the thermocouple immersed in the melt. Temperature variation over the depth of the melt was less than ± 3°C. The inactive melts were prepared from pure native quartz, assaying better than 99.9 pct SiO2, A.R. grade A12O3 and A.R. grade CaCO,. The same quartz and CaCO3 were used in preparing the active melts, the

Jan 1, 1962

R. Culver, Colorado School of Mines I appreciated Professor Starfield's presentation, because his approach to blasting research reflects my feelings that a lot of practical work can be done toward making short-term advances that can be used by the blasting industry. We should not forget this in our attempt to obtain solutions to such idealized problems as a mathematical theory of cratering. The blasting industry would like very much to have the efficiency of the basic blasting processes improved from the range of 20 percent up into the range of 50 percent. And many of these problems should be approached and attacked in the laboratories. Blasting research at the Colorado School of Mines for the past two or three years has been aimed at improving the pre-splitting process, because we feel it will become increasingly important to the construction industry. We have attempted to develop a unified theory of how pre-splitting works; and the more we investigate, the more variables we find. We may never obtain an entirely satisfactory theory of pre-splitting, but we have developed a tentative explanation. One of our first conclusions was that we are making very poor use of the explosive in current pre-splitting practice. But to appreciate this we must first consider how pre-splitting works. A series of parallel boreholes are loaded with low density charges which are detonated simultaneously. (Delayed detonation has been tried, but most people agree that simultaneous detonation is best, and this is what we found.) Stress waves traveling out from each borehole interact with the stress waves from the two adjacent boreholes influencing the direction of the fractures that occur and propagate from each borehole. It has been suggested in private communication with Mr. Wilbur Duvall of the U. S. Bureau of Mines, that the fracture between the adjacent boreholes is a result of the net particle velocities above and below the pre-split plane which tend to set up a net tension along the pre-split plane. Regardless of what the exact mechanism is that causes the fracture to propagate from one borehole to the next, we know that it, in general, relies upon an interaction of the stress waves. However, if there is a large compressive stress normal to the pre-split place, it can practically eliminate any possibility of obtaining the desired pre-split by preventing the desired fractures from getting started. Aside from obtaining a fracture along the pre-split plane, the other major aim of pre-splitting is to minimize the fracturing that occurs around the borehole. We do this by drilling a large hole and putting a small charge in the middle of it. This results in a badly decoupled charge which is very inefficient; most of the energy is used in compressing the air in the borehole. Out of discussions about how pre-splitting works, we decided that perhaps there was some other explosive geometry which would make more efficient use of the explosive, and result in optimizing the pre-splitting process. Starting in the laboratory with small plexiglas blocks, we found that a fully-coupled explosive charge of 5 grains/in. of PETN gave random fractures extending about I in. from the borehole. A 1/4 in. plexiglas plug fit into a 1/4 in. hole in a similar block with the same fully coupled charge gave random fractures extending out only about 1/2 in. due to the energy absorbed in fracturing the plug. If the plug was split longitudinally but otherwise using the same geometry, it was possible to drive a fracture about 2 in. in either direction from the borehole, with an even smaller amount of fracturing around the borehole.

Jan 1, 1967

By E. J. Roberts

F. C. Bond (Allis-Chalmers Mfg. Corp., Milwaukee) —This paper considers comminution as a first order process, with the reduction rate depending directly upon the amount of oversize material present. The data show that other factors should be taken into account, and it is possible that in time these may be evaluated as simultaneous or consecutive reactions: Development of the theory of comminution has been retarded for many years by the assumption that surface area measurements constitute the sine qua non of the work done in crushing and grinding, and it is encouraging to note the belated growth of other ideas. In the Abstract the term "net power" should be changed to "net energy." Throughout the paper the term "hp per ton" should be changed to "hp hrs per ton", or "hp hr t." The term "Probability Theory" in the title does not seem appropriate, since it is not clear how the probability theory is used in developing the ideas in the paper. There seems to be a contradiction between the large calculated advantages of closed circuit operation and the statement following that the closed circuit test results showed no significant change in grinding behavior, when compared with the batch grind curves. Tables I and II show that between 75 pct and 50 pct solids the energy input required decreases with increasing moisture content and may indicate the advisability of grinding at higher dilutions in certain cases. The calculation of the hp-hr per ton factor indicates an input in the laboratory mill of only 7.32 gross hp per ton of balls; this casts some doubt upon the accuracy of the factor used, since the power input in commercial mills at 80 pct critical speed is customarily much higher. The tests show that within fairly wide limits the amount of ore in the laboratory mill may be varied and a product of constant fineness obtained, provided that the grinding time is varied in the same proportion. This has often been assumed, and confirmation by actual testing is of value. The Cavg corrections for differences between the plant and laboratory size distributions do not seem very satisfactory, since in many cases the plant/laboratory ratio is farther from unity after correction than before. The following equation has been derived from the data in Table VI: Relative Energy (log new ball diam in in. + 0.410) Input = --------------—--------------- from which the relative energy inputs for balls of different sizes can be calculated and compared. The relative energy input is unity for balls of 2.715 in. diam. The equation indicates that the work accomplished by a ton of grinding balls per unit of energy input is roughly proportional to the square root of the total ball surface area; provided, of course, that the balls are sufficiently large to break the material. The data in support of this statement are admittedly meager, but are fairly consistent when plotted. The relative grindability values listed in Table VI for 200 mesh multiplied by 4/5 apparently correspond approximately to the A-C grindability at 200 mesh.' It would seem that for open circuit tests comparable accuracy could be obtained much more simply by the old method' of plotting the test grind, extending the mesh grinds to the left of zero time if necessary, and determining from the plot the equivalent time required to grind from the plant feed size to the plant product size, using the average of several mesh sizes. The en- ergy input value of one time interval could be determined by tests on materials of known grinding resistance, and this multiplied by the interval required should give the desired energy input value. The relative grindabilities would be the relative time intervals required for a specified feed and product size. When the plotted mesh size lines of a homogeneous material are extended to the left beyond zero time they meet at one point at zero pct passing. The horizontal distance of this point from zero time indicates the equivalent energy input required to prepare the mill feed. The author's results show that the closed circuit grinding tests give about the same K values as open circuit tests, from which he concludes that open circuit tests are satisfactory in many cases. The value of the closed circuit test is its ability accurately to predict energy requirements in closed circuit grinding for both homogeneous and heterogeneous materials. If the material is homogeneous, the open circuit test gives satisfactory results; but if the material contains appreciable fractions of hard and soft grinding ore, the open circuit tests will not be accurate because of the accumulation of hard grinding material in the circulating load. Since in most cases it is not possible to determine a priori whether the material contains hard and soft fractions, the closed circuit tests are preferable and more reliable. B. S. Crocker (Lake Shore Mines, Ontario)—Dr. Roberts probability theory of grinding is very similar to our log pct reduced vs. log tonnage method of plotting and evaluating grinding tests at Lake Shore. However, although we both seem to start at the same point we finish with different end results. Shortly after publishing our grinding paper (referred to by Dr. Roberts) in 1939, we did pursue the subject of the "constant pct reduction in the pct +28 micron material for each constant interval of time. We ran innumerable tonnage tests on the plant ball mills, rod mills, tube mills with 11/4 and 3/4 balls, and lastly pebble mills, with tonnage variations from 180 tons per day to 950 tons per day. We found that when we plotted the log of the tonnage against the log of the pct reduced of any reliable mesh, we had a straight line up until 90 pct of the mesh is reduced. We have also tested this in our 12-in. laboratory mill with the same results. We have used this method of evaluating grinds for the past 8 years and developed the recent four stage pebble plant on this basis. By pct reduced we mean the percentage of any given mesh that is reduced in one pass through a mill at a given tonnage (or time). For example, if the feed to a rod mill is 90 pct +35 mesh and the discharge at 500 tons per day is 54 pct +35, the pct reduced is 90 — 54/90 = 40 pct. If the feed had been 80 pct +35 the discharge would have been 48 pct +35 or pct re- duced 80-48/80 = 40 pct as long as the tonnage re- mained constant at 500 tons per day. Thus we can easily correct for normal variation of mill feeds. This log — log relationship derived from the tonnage tests of all our operating mills has proved of tremendous help in checking laboratory work and in designing alternate layouts or new plants. The difference between the log — log and the semi-log plot is only shown up when the extremes in tonnages are plotted. When the relationship between the pct reduced and the tonnage was first investigated, we used semilog

Jan 1, 1952

By W. S. Tower

STEEL is the basic metal, the main metallic prop of the modern industrial world, a good gage for measuring the state of our complex economy. Any who had doubts on that score should have had them dispelled by the many evidences of public concern over the affairs of the steel industry in recent months. I do not need to relate the various criticisms of the industry, nor the questions about its policies and performance which have come in a rising flood, especially from unthinking and irresponsible sources. But judged from the standpoint of production, or from plans to improve and expand facilities, or from technical progress, the facts about the steel industry are proof of

Jan 1, 1948

By W. B. Dancy, A. Adams

Laboratory test work on heavy liquid separation of sylvite from halite is reported. Numerous tests were run on sylvite ore sized in the ranges of 4x20 mesh, 10x65 mesh, 8x100 mesh, -8 mesh and -10 mesh with heavy liquids in the range of 2.05 to 2.15 sp gr. From the test results, it was concluded that, with the type of ore under study and a size in the range of -8 mesh, a recovery as high as 90% could be achieved with a product grade of 70% KCl. However, a final product at an acceptable recovery cannot be made with one pass, and the float must either be further processed with heavy liquids or dried and sent to a conventional froth flotation circuit. Potash ores occurring in this country consist essentially of sylvite and halite plus minor amounts of magnesium sulfate salts and montmoril-lonite-type clays. Recovery of potash minerals from evaporite ores in the North American potash fields is accomplished almost exclusively by use of amine flotation. European practice involves froth flotation as well as solution-crystallization processes. Laboratory and pilot plant test work has been reported in Europe and the U. S. on the application of heavy media separation to potash ore beneficiation. Work was probably discontinued because of lack of ore with the required very coarse liberation characteristics (1/8 to 1/2 in. liberation size). Sylvite, with a gravity of 1.99, and halite, with a gravity of 2.17, appear to be ideal for separation by heavy liquids, which are now available in gravities from 1.59 to 2.95. This paper reviews preliminary results obtained from laboratory test work on heavy liquid separation of sylvite from halite. TEST WORK The heavy liquids used in the tests under discussion were chlorobromethane, with a specific gravity of 1.923, and dibromethane, with a gravity of 2.490. These liquids, completely miscible, were combined in the proportions needed to give a mixture having the desired specific gravity. Feed for the laboratory tests was mine-run ore screened to the desired mesh sizes. In conducting the tests, the sample was fed at a constant rate into a stream of heavy liquid and the mixture directed into a small separatory vessel. The float overflowed into a collecting pan while the sink collected in the bottom of the separatory vessel and was removed at the end of the test. Approximately 500 g of feed constituted a charge. Pulp density of the feed was kept low to prevent particle to particle interference in separation. With feed in the range of 8x100 mesh, a pulp density of under 10% solids by weight was found advisable. With coarser feed the pulp density could be carried as high as 15% solids. Time of separation was very rapid. In the case of 4x20-mesh material, separation was effected in 15 to 30 sec; with -10-mesh feed, separation required about 1 to 2 min. SPECIAL EQUIPMENT Since heavy liquids are toxic to varying degrees, all separatory work was carried out in a standard laboratory fume hood. It was noted that complete removal of fumes was not being effected; therefore the hood construction was modified, resulting in a completely satisfactory arrangement for heavy liquid test work. In the interest of safety, details of this fume hood are reported here. Unlike most fumes, heavy liquid fumes tend to settle and flow like water, rather than to rise like a gas. Working on this assumption, a standard water drain was installed in the hood. Across the front of the hood a 1-in. barrier was constructed. In the rear of the hood a false back was installed, with an adjustable sliding door on both the bottom and top of this panel. As shown in Fig. 1, the exhaust fan pulled a vacuum behind the barrier, sucking the heavy fumes from the bottom of the hood. Another addition was the drying box, shown to the right of the hood. This is simply a box covered on top with hardware cloth and connected by a 6-in. inlet to the hood. Sample trays made of fine mesh wire filter screens were found ideal for drying samples. With this arrangement, air flowed completely through the sample and all fumes were drawn into the hood. In use, it was found effective to cover with a

Jan 1, 1963

For the year ending February, 1918 PRESIDENT PHILIP N. MOORE ST. Louis, Mo. PAST PRESIDENTS WILLIAM L. SAUNDERS NEW YORK, N. Y. L. D. RICKETTS NEW YORK, N. Y. FIRST VICE-PRESIDENT SIDNEY J. JENNINGS NEW YORK, N. Y. TREASURER GEORGE C. STONE, NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON, NEW YORK, N. Y.

Jan 5, 1917

THE CHAIRMAN (A. F. Lucas, Washington, D. C.).-Mr. Matteson has stated that the drilling of certain deep wells has proved a failure because they were abandoned too soon. He advises drilling more wells around salt domes, in the hope of finding additional oil sands. I have had some experience on the domes and believe that by drilling shallow wells, one loses time and money. I have advanced the opinion -that by drilling central wells in the -most likely location of a dome, showing is certain weakness, a better result could be obtained. I have in mind one locality where Mr. Knapp drilled a well through the salt¬the only location that I know of on the Gulf Coast where oil was found underneath the salt. Mr. Knapp found a great deal of gas in it. The salt itself was impregnated with oil and gas; and my opinion is that in such instances, instead of drilling so many wells around a dome, if you will attack at a weak point to as great a depth as a drill will go, the results will he much better. At present we have instances where drills have penetrated to 7300 or 7400 ft. in depth. Why couldn't the rich companies that are operating around the Gulf Coast arrange to get some special drilling apparatus and drill with the rotary first for, say, 3000 to 4000 ft., always in the likely location, and then proceed with the cable? I think we need just such work. In Mr. Matteson's paper lie quotes from an author whose writings in the Federal Bulletin and in the Louisiana Bulletins have been quite extensive. He states that oil and asphalt have originally been found on the surface of those domes. I have been over and examined nearly all of those domes (not all of them, because many have been developed in the last few years) and found no such occurrence at the time; and in the old well-known humps or big hills, as they generally called them; I have never found either salines or asphalt or petroleum. In only' one instance it looked as though asphalt night have exuded out of the ground, and that was in the Sour Lake, but right in that neighborhood years previous to that a company had operated commercially-they had a little refinery there-and had found it so unprofitable that they pulled up stakes and quit.

Jan 4, 1918

IRON AND STEEL COMMITTEE ALBERT SAUVEUR, Chairman A. A. STEVENSON, Vice-Chairman HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. Guilliaem Aertsen, Henry M. Howe, E. Gybbon Spilsbury, John Birkinbine, _Robert-W. Hunt, J, S. Unger; William-H. Blauvelt, J:-E: Johnson, Jr., Felix A: Vogel; Charles A. Buck, Charles Kirchhoff, Leonard Waldo, Ernest F. Burchard, Richard Moldenke, William R. Walker, F. D. Carney, Charles F. Rand, William R. Webster, James Gayley, Joseph W. Richards, Frederick W. Wood. Henry D. Hibbard, C. F. W. Rys, There will be a meeting of the Institute in Pittsburg on Oct. 8, 9, and 10, 1914. This meeting will be under the joint auspices of the Iron and Steel Committee, the Committee on Coal and Coke, and the Committee on Petroleum and Gas. The iron and steel papers will probably be presented on Oct. 8. The following papers have been received and accepted and will be read at the October meeting.

Jan 6, 1914

By P. J. Potter

PRACTICALLY all tin-base babbitt metals used in engine bearings are made to customers' specifications, which are many and varied. The copper ranges from 3 to 8 per cent. and the antimony from 4 to 13 per cent.; generally, the babbitt with lower copper content will contain from 4 to 8 per cent. antimony and that with higher copper will have from 7 to 13 per cent. antimony. The allowable lead content varies from 0.20 to 2.00 per cent. If a solder is used as a bonding material instead of tin, the resulting material in the finished bearing will have a higher lead content, but it would not be enough to bring the lead above specificational limits. Impurities such as iron, arsenic and bismuth should be determined in the tin before using to insure a uniform and high-grade product. These points must be considered when segregating and grading the waste that comes from the finishing operations on lined bearings.

Jan 1, 1929

By Robert H. Richards

THE Institute of Mining Engineers has shown so much interest in the educational problem of profitably combining theory and practice, that it seems especially appropriate to lay before its members the methods and aims of the mining laboratory of which I have charge, and in which one form of combination of hand with head work is now being tried. If anything may be contributed toward the solution of this problem by the discussion which follows, my purpose mill be attained. Whether it was wise or not to establish a mining school so far from the principal mining centres, does not now enter into the question. Given, a mining school already begun, how shall it be made most efficient in developing engineers who are trained to think for themselves as well as versed in the works of others ? This is the question with which we have had to deal. In considering the bearing of this laboratory work upon the students' preparation, it will be convenient to take it up under five different heads: 1. The methods and aims of the laboratory. 2. The advantage to students of having a part, at least, of their practical work in the curriculum of their school. 3. The advantage to be derived by mine; and works. 4. Degree of accuracy which may be attained in working ores on a small scale. 5. Reslts of work in the laboratory. 1. The Methods and Aims of the Laboratory.—During the May meeting of 1873, held in Boston, I had the privilege of reading before you a paper stating the plan; and aims of this laboratory. Since that time me have been constantly following out those plans, and are more than ever convineed that me are working in the right direction. We do not feel that the time we have spent has been in any sense thrown away. Perhaps the aims of the laboratory can be most clearly shown by illustration. Many young engineers have school thinking that they know everything. They go to the works, and expect to teach the superintendent something and the men a good deal, regardless of the fact that it is this spirit that has prejudiced workmen against schoolmen. They are often more trouble than they

Jan 1, 1879

For the year ending February, 1918 PRESIDENT PHILIP N. MOORE ST. Louis, Mo. PAST PRESIDENTS WILLIAM L. SAUNDERS NEW YORK, N. Y. L. D. RICKETTS NEW YORK, N. Y. FIRST VICE-PRESIDENT SIDNEY J. JENNINGS NEW YORK, N. Y. TREASURER GEORGE C. STONE, NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N.Y.

Jan 9, 1917

S. F. EMMONS, Washington, D. C.: Papers of Collins, Vogt, DeLaunay, etc.-Mr. Collins tells us about facts in the veins of Cornwall that suggest secondary sulphide-enrichment is highly interesting; and I am free to confess that I have not studied the literature of that region as fully as I should have done. Nevertheless, even if it had been as familiar to me as it is to Mr. Collins, I should probably have hesitated to draw theoretical conclusions without having seen the mines myself; for the personal equation and the point of view of the observer play, perhaps, a larger part in the study of ore-deposits than in that of any other natural phenomena. One important purpose of my paper, and its publication at the time of the Washington meeting, was to call forth remarks from other geologists upon deposits with which they were personally familiar, or to lead them to re-examine such deposits with the idea of secondary enrichment in mind. Mr. Collins's remarks on Rio Tinto, which he has the advantage of personally knowing, are also interesting. With regard, however, to his suggestion-advanced as an apparent argument against our theory-that the re-precipitation of copper from cupric sulphate solution by pyrite can hardly take place there, since it would upset the commercial process, I would remark that, while he is undoubtedly right as to the fact, it does not militate against the reduction and re-precipitation of cupric sulphate in veins; since on the surface, as at Rio Tinto, there is free access of air, and consequently an excess of ferric sulphate, whereas in depth the ferric sulphate would have been mostly reduced to ferrous sulphate, and (there being no excess of acid to hold it in solution) the small amount of copper in the presence of an excess of iron sulphide would be precipitated either as sulphide or as native copper. To Professor Vogt's analogous remarks, that in his experience sulphuric acid is formed only in subordinate amount in the attack of sulphides by ferric sulphate, I would say that Dr.

Jan 1, 1902

By J. A. Herrick Nashua

IN this country steel made in a Siemens furnace or Bessemer converter, is generally tapped into a ladle or shoe, and then drawn through an aperture in its base into the various moulds. In order to regulate the flow of the molten mass a refractory valve is arranged at the aperture. A plumbago nozzle is fixed firmly in this aperture, and a stopper of like material is fitted to it, making a socket valve. In order to raise and depress this stopper at will, a rod is fastened-to it, extending through, the metal and over the brim of the ladle, where it is bent back in a half circle and secured in a slide. This slide plays vertically in a frame, permanently fastened to the outside of the ladle, and is moved by a lever having as a fulcrum a pin fixed in this frame, one end, of the lever being temporarily fixed to the slide, and the other end being moved by hand. Reference being had to the drawing (see Plate 1, Fig. 1), E is the nozzle, D is the stopper, A is the rod, protected as hereinafter described, C is the cast-iron framework, B is the wrought-iron slide, B' is the offset into which the rod, A, enters, and is secured in the usual manner by a key, a. Section J, K, shows the manner of hanging the lever. J is a pin attached to the slide by which the end of the lever raises the slide, B. J is the fulcrum fastened to the frame, C. K (Fig. 1) is a hand-nut fastening the slide, B, to the frame, C, at will. Fig. 2 is a side elevation of ladle, showing the outside working of the parts above described. It is the common practice to protect the rod, A, by a coating of clay and fire-sand, kneaded to the right consistency and applied to the rod, and then thoroughly dried. Just before casting, the plumbago stopper, D, is heated at its extremity to redness separate from the ladle and, at the moment of pouring, is placed in the ladle and slide, and adjusted as well as practicable. Some very serious defects ensue, causing much trouble and vexation as well as actual loss. The fire-clay coating in drying becomes cracked and seamy, and at its best is more or less loose on the rod. The hot metal sometimes cuts

Jan 1, 1879