Search Documents

By L. L. Melton, D. L. Lord, B. W. Hulsey

A mathematical model d1.20p/4L = A(8v)8 derived from the Blasius equation is proposed to be applicable to turbulent flow through straight cylindrical pipe for time-independent fluids which produce a diameter family of straight parallel lines on a log (dp/4L) vs log (8v/d) plot or stress-flow diagram. Such a correlation should permit scale-up with data taken from one pipe diameter for Newtonian, inelastic non-Newtonian and viscoelastic fluids, such as dilute polymer fracturing fluids, which produce considerable frictional pressure reductions. The Newtonian diameter exponent value 1.20 is shown to be empirically valid for turbulent non-Newtonian flow by application of numerical analysis methods. Multiple regression analysis is applied to a logarithmic linearization of the proposed model. An improved data fit results from further linearization achieved by taking linear terms from a generalized Taylor's series expansion about the multiple regression coefficients. Extensive experimental data obtained in five pipe diameters with water, sodium carboxymethyl-celIulose solutions, guar gum solutions, bentonite clay suspensions and calcium carbonate slurries are presented. Except for calcium carbonate slurries, which were investigated rather than time-dependent cement slurries, the fluids studied contain drilling or fracturing fluid additives. The behavior exhibited by these fluids is considered typical of most fluids encountered in drilling, cementing and fracturing operations. INTRODUCTION Considerable difficulties have been encountered in predicting turbulent flow pressure drops produced by non-Newtonian fluids flowing through straight cylindrical pipe. Correlations previously presented require extensive experimental data which represent several pipe diameters and a wide flow rate range to estimate the necessary scale-up parameters.l-7 One must implement either elaborate experimental apparatus or spend considerable time and effort to gather these data. Presented here is a correlation method which should minimize the experimental effort and data analysis normally required by utilizing flow data taken with only one pipe diameter. Turbulent flow data (up-stream and down-stream pressure and volumetric flow rates) were collected for five pipe diameters through operation of a small pipeline system having an electronic data acquisition and digitizing system. A mathematical model derived from the Blasius equation was utilized to describe the functional relationship between pressure drop and the two independent variables, diameter and average flow velocity. A correlation, which should produce a valid single-pipe scale-up, resulted from a computer-implemented statistical and numerical data analysis for several time-independent non-Newtonian fluids.

(This list. includes only those who have entered military service within the past month, or whose entry has only recently become known to us; it also includes a few names of those whose titles or assignments have been changed within the month. A complete list will he found in the Year Book mailed with this Bulletin. Another Honor Roll is maintained in the reception room of the Institute.) ALDEN, HERBERT W., Lieutenant-Colonel, Ordnance Dept. ALDER, ALFRED; Engineers' Reserve Corps. ALFORD, NEWELL G., Sergeant, Bureau of War Risk Insurance, Headquarters 84th Division. AMBLER, HARRY A., Lieutenant, 30th Infantry. ANDERSON, GEORGE K., JR., Sec. C, 1st Co.; 3d Officers' Training Camp. AYER, -FRANK A., 1st Lieutenant, 43d Squadron, 3d Prov. Regiment, Aviation Camp.

Jan 3, 1918

By Walter S. Weeks

THE subject of the flow of air through a mine under the influence of natural ventilation has proved an elusive one. To my knowledge only cut and try algebraic solutions have been used where multiple paths are involved. The object of this paper is to present a method for the graphical determination of the flow induced by the natural ventilation pressure (N.V.P.) alone or in combination with a fan. The N.V.P., measured in pounds per square foot, induced by two columns of air between two horizontal planes at different elevations, is equal to the difference in weight of the two columns, assuming each to have a cross-sectional area of 1 sq. ft. Pressure in pounds per square foot is converted into inches of water by dividing by 5.19. Methods of calculating the N.V.P. have been discussed in the literature. In this paper, for simplification of exposition, the change in pressure due to the weight of superimposed air will be assumed directly proportional to the length of the column. The actual methods of calculating the N.V.P. do not affect the solutions to be presented. It must be realized that the precision to be obtained from the small- scale, inked diagrams presented is not as great as would be obtained from large-scale, penciled curves that would be used in practice. The accuracy of the curves does not warrant reading "volumes" closer than the nearest thousand cubic feet per minute. CASE I. DUCTS IN SERIES The simplest type of problem is to determine the flow when two shafts are connected by a crosscut, as shown in Fig. 1. In this example, the resistance of the shafts is to be taken as 0.0001 in. of water for a flow of 1000 cu. ft. per minute for a length of 1000 ft. The resistance of a crosscut is to be taken as 0.0005 in. of water for a flow of 1000 cu. ft. per minute. The small pressures necessary to cause changes in velocity will not be considered, because the accuracy of other obtainable data does not warrant their consideration.

Jan 1, 1938

By C. L. Sollenberger, R. B. Greenwalt

PERHAPS the most widely used dispersants or gangue depressants in nonmetallic flotation are sodium silicates, which vary in silica-to-soda ratio from 1 to 3.75. Typical manufactured silicates in order of decreasing solubility and increasing amounts of silica are Metso, silica-to-soda ratio of 1.00; D, 2.00; RU, 2.40; K, 2.90; N, 3.22; and S-35, 3.75.* References in flotation literature's to the use of sodium silicates are often weak because they fail to mention the type of silicate used. Metso and silicate N have occasionally been mentioned, but when the type of silicate is not mentioned, it is usually assumed to be N, the cheapest of the soluble silicates and the one recommended by sodium silicate manufacturers as a flotation agent.

Jan 6, 1958

By Kenzo Ikeda

The Kosaka smelter is situated in the extreme northern end of Hondo (the main island of Japan) 15 mi. east of Odate, on the government railroad, to which it is connected by a private railway. It contains ten blast furnaces having a maximum daily capacity of 1600 short tons of ore, conducting a slow pyritic smelting entirely without coke or limestone, and with a charge carrying over 50 per cent. of briquetted and agglomerated fines. The matte (35 per cent. Cu) is blown in two basic-lined barrel converters, the blister copper (98.8 per cent. Cu) being cast at once into anodes. The adjoining refinery contains 600 tanks with a maximum capacity of 1300 tons of cathodes per month, the byproducts being gold, silver, and bismuth. At present, working at about half capacity, the whole plant consumes 2000 kw. of hydro-electric power, and employs 850 men and women. The ores are derived from two principal sources: The relatively new Hanaoka mine, 20 mi. from the smelter, yielding copper pyrites by underground mining, and the old Kosaka open-cut mine, 1 1/2 mi. from the smelter, yielding three different ores: (a) kuromono, a compact finegrained mixture of barite (32 per cent.), zinc blende, galena, and pyrite, the whole carrying about 2.5 per cent. Cu; (6) cupriferous pyrites with 2.4 per cent. Cu; (c) siliceous ore with 2 per cent. Cu. The Hanaoka ore now constitutes approximately one-half of the charge, almost replacing the Kosaka kuromono which was the ore chiefly smelted until 1913.'

Jan 1, 1923

By Kenzo Ikeda

The Kosaka smelter is situated in the extreme northern end of Hondo (the main island of Japan) 15 mi. east of Odate, on the government railroad, to which it is connected by a private railway. It contains ten blast furnaces having a maximum daily capacity of 1600 short tons of ore, conducting a slow pyritic smelting entirely without coke or limestone, and with a charge carrying over 50 per cent. of briquetted and agglomerated fines. The matte (35 per cent. Cu) is blown in two basic-lined barrel converters, the blister copper (98.8 per cent. Cu) being cast at once into anodes. The adjoining refinery contains 600 tanks with a maximum capacity of 1300 tons of cathodes per month, the byproducts being gold, silver, and bismuth. At present, working at about half capacity, the whole plant consumes 2000 kw. of hydro-electric power, and employs 850 men and women. The ores are derived from two principal sources: The relatively new Hanaoka mine, 20 mi. from the smelter, yielding copper pyrites by underground mining, and the old Kosaka open-cut mine, 1 1/2 mi. from the smelter, yielding three different ores: (a) kuromono, a compact finegrained mixture of barite (32 per cent.), zinc blende, galena, and pyrite, the whole carrying about 2.5 per cent. Cu; (6) cupriferous pyrites with 2.4 per cent. Cu; (c) siliceous ore with 2 per cent. Cu. The Hanaoka ore now constitutes approximately one-half of the charge, almost replacing the Kosaka kuromono which was the ore chiefly smelted until 1913.'

Jan 1, 1923

COUNCIL OF NATIONAL DEFENSE W: S. GIFFORD, Director, GROSVENOR B. CLARKSON, Secretary. The Council of National Defense The Advisory Commission NEWTON D. BAKER, DANIEL WILLARD, Chairman, Secretary of War, Chairman.. (Transportation). JOSEPHUS DANIELS, BERNARD M. BARUCH, Secretary of the Navy. ' (Raw Materials). DAVID F. HUSTON, HOWARD E. COFFIN, Secretary of Agriculture. (Munitions, Manufacturing). FRANKLIN K. LANE, HOLLIS GODFREY, Secretary of the Interior. (Science and Research, including En¬ WILLIAM C. REDFIELD, gineerlng and Education). Secretary of Commerce, SAMUEL M. GOMPERS, WILLIAM B. WILSON, (Labor). Secretary of Labor. F. H. MARTIN, (Medicine and Sanitation). ' JULIUS ROSENWALD, (Supplies). At the request of Dr. Hollis Godfrey, Chairman of the Advisory Committee On Science and Research, which includes Engineering and Education, a Sub-Committee of Engineering Societies has been appointed with representatives as follows:

Jan 6, 1917

By E. W. Davis

DURING late years, the proportion of beileficiated iron ore shipped from the Lake Superior District has increased very rapidly. By benefication is meant washing, screening, drying, sintering or any process by which the grade or structure of the crude ore is improved before shipment. In 1915, only 3,000,- 000 tons, or 9 per cent, of t6e total Minnesota shipment was beneficiated ore, compared with 13,500,000 tons, or 35 per cent, of the total Minnesota shipment in 1925. This increase is, of course, due to the fact that iron and steel can be made more cheaply after beneficiating these ores than they could have been had these ores not been so treated. Fundamentally, however, several causes contribute to the necessity for beneficiating iron ores, such as depletion of the reserves of high-grade ores, the iron ore leasing systems and taxation methods and, at the smelting plants, a better understanding of blast-furnace operations, increased operating costs and increased sulfur content of blast-furnace coke. As economic conditions change, it is by no means certain that the proportion of beneficiated ore shipped each year is going to continue to increase. Undoubtedly some of the beneficiation operations are not economically sound at the present time and what the future has in store for the iron ore industry is problematical. Generally speaking, the cost of fuel for blast-furnace operations will increase as time goes on and in order to continue to produce cheap iron and steel, some of the other costs must be lowered. Freight and labor rates probably can- not be reduced. The cost of producing iron ore cannot be reduced much below the present price. It therefore appears that the best opportunity for maintaining iron and steel prices at their present level in spite of in- creased costs of labor and raw materials is to use. less or cheaper raw materials. This, of course, contemplates an improvement in metallurgical processes all along the line and, as a matter of fact, we can confidently expect these improvements because scientific investigations will undoubtedly be even more productive in the future than they have been in the past.

Jan 1, 1926

By P. R., Bradley

THE Juneau gold belt is divided into ore-bands of poor definition. The most easterly workings on the , belt, those of the Alaska Gastineau Co., disclosed three separate bands: the Footwall or Ground-hog band, 70 ft. wide; the Perseverance band on which the recent mining was done, also 70 ft. wide; and the No. 2 band, 100 ft. wide. These bands, aggregating 240 ft., are found over a width of 2000 ft. Going toward the west into the adjoining Alaska Juneau ground, four bands have been found which have a total 'right-angle thickness of 755 ft. These bands are convergent in their westerly trend and terminate on the plane of Silver Bow fault. The four bands have better definition at the fault plane than at the eastern boundary line where they enter the property. -Along the property line, the width of the bands and intervening country is 1600 ft., and at the Silver Bow fault this width is reduced to 1300 ft. The distance from the eastern property line to Silver Bow fault is 2400 ft. The bands are slate or slate with metagabbro intrusions, together with gold-bearing quartz masses, stringers, and gash veins. The bands themselves are not all ore, but all commercial .ore is found within the bands. They have no uniform width either in horizontal or vertical section. The ore has no hard and fast boundary except where cut by faults, and profitable mining ceases on a vague and

Jan 1, 1929

By R. G. Knickerbocker

The copper smelter and refinery of The Messina (Transvaal) Development Co. Ltd., at Messina, South Africa, was erected in 1920 and 1921, but initial operations were deferred until late in 1922 on account of the collapse of the copper market in the interim. Because the anticipated production was to be only 20 tons of copper per day from a high-grade matte containing 60 per cent copper, and because the ore did not contain gold or silver in quantities sufficient to pay for separation from the copper bullion, it was decided to design the plant along lines quite different from the modern smelteries treating large quantities of sulfide ores carrying appreciable amounts of gold and silver. The plant was built, therefore, for the production of copper by the Nicholls-James process. By this method two-thirds of the copper matte produced was roasted in a Merton calciner and charged into a bath of the remaining one-third portion of unroasted matte in a reaction furnace. The original design was not only novel in providing for the Nicholls-James process, but also in comparison with new plants built elsewhere, because of factors inherent in the locality. Sources of supply for machinery were very remote; it takes three months after the placing of an order to accomplish delivery of machinery into Messina from the United States. Native labor was available at 30 to 40¢ per 8-hr. shift. These factors permitted plant design which provided no overhead cranes, no matte ladles, no slag pots or other usual mechanical means of transportation between departments. The design resulted in a compact simple plant with furnaces arranged close together and terraced so as to provide for gravity transfer of molten material from one furnace to another and for manual disposal of products. Fig. 1 shows the relative location of furnaces. The three furnaces are parallel on successively decreasing elevations. A superimposed feed floor was provided above the furnaces. All three furnaces were provided with coal-dust burners served from a Bonnot system of coal-dust transportation, and the waste gases were discharged into waste-heat boilers. A short trial of the Nicholls-James process developed several facts which brought about a decision to abandon the process. Owing to the

Jan 1, 1934

By W. B. Triplett, H. I. Aaronson, G. M. Andes

THE morphology and mechanism of the proeutectoid a and the eutectoid reactions have been recently investigated in some detail in an iodide-base Ti—7.22 pct Cr alloy.' These studies have now been extended to an iodide-base Ti—10.8 pct Cr alloy in order to evaluate the effects of composition on the proeutectoid and eutectoid transformations in titanium-chromium alloys. The alloy used in this investigation had the following composition: 10.8 Cr, 0.0327 0, 0.011 N, 0.0063 H, and 0.011 pct C. Specimens of this alloy were heat treated in evacuated and internally get-tered Vycor capsules. The specimens were solu-

Jan 1, 1959

By D. J. DeLazaro, W. Rostoker, R. E. Riley, M. Hansen

At very low concentrations, carbon dissolves interstitially in molybdenum resulting in a linear expansion of lattice parameter with increase of carbon in solid solution. Geometrical consideration of the relative size of carbon atom to size of interstice approximately predicts the observed volume expansion. THE element carbon, occurring in molybdenum, either as an unavoidable impurity, or purposely added, markedly affects the mechanical properties of molybdenum. Several investigators1-" have noted the occurrence of molybdenum carbide at the grain boundaries of cast molybdenum, and Fischer and Rengstorff' have shown that this intergranular constituent can induce intergranular brittleness. The appreciable change, with temperature, of the solid solubility of carbon in molybdenum, found by Few and Manning," suggests other important effects upon mechanical properties. Finally the relative atom diameters of carbon and molybdenum (the ratio of atom diameters is 0.59) are indicative, by analogy with iron (ratio of carbon atom diameter to iron atom diameter is 0.65), of a possible interstitial solid solution. If carbon dissolves intersti-tially in molybdenum, anelastic effects and age-hardening effects, similar to those observed in other body-centered cubic metals, could be expected. However, from the work of Sykes, Van Horn, and Tucker," it might be inferred that carbon forms only a substitutional solid solution with molybdenum. These considerations made it desirable to study the effect of carbon on the lattice parameter of molybdenum in greater detail than heretofore. All heat treating was done in a high temperature furnace7 built specifically for heat treatment of molybdenum. The temperatures and times of heat treatment were determined from the a solubility limit for the Mo-C system." These heat treatments were carried out in argon which was purified with respect to N, and H.!0." Purification of the argon was accomplished by passing the argon over hot (750°C) titanium and then through a magnesium perchlorate drying tower. As many as six samples were run concurrently and quenched at different times without interrupting the furnace cycle. Both the purity of the furnace atmosphere and ability to quench samples from any temperature up to 4000 °F were of prime importance in the successful heat treatment of samples for the lattice parameter investigation. Carbon Analysis The Leco Combustion apparatus was used for carbon analysis. This apparatus is capable of an accuracy of & 0.003 pct for a 1 g sample in the range below 0.10 pct. However, it is felt the degree of accuracy is somewhat better than this limit in view of the consistency evident by cross checking a number of determinations. The Battelle Analytical Laboratory consistently reported check results to within k 0.001 pct C. X-ray Measurements The molybdenum wire specimens (20 mils) were carefully filed down to about 12 mils and then etched with nitric acid to 8 mils. Carbon analyses were made on specimens before reduction in size; however, since there was no evidence of surface carburization, it is probable that the carbon was uniformly distributed throughout the sample. The resultant specimens were strain free and small enough to minimize the error in the lattice parameter determinations due to X-ray absorption. Diffraction patterns were obtained with a Debye-Scherrer powder camera 114.59 mm in diam utilizing the Straumanis type asymmetrical film mounting. Nickel-filtered copper. Ka radiation and zirconium-filtered molybdenum Ka radiation were used. Line positions on the film were measured with a traveling microscope equipped with a vernier scale permitting measurement to 0.001 cm. The average of five readings was used to determine the position of each line. The lattice parameter for each specimen was determined from the data by the extrapolation method of Bradley and Jay, Y.e., the intercept at 90" of the straight line obtained by plotting the apparent lat-

Jan 1, 1953

By R. M. Rose, D. P. Ferriss, J. Wulff

Single crystals of tantalum, tungsten, and the binary alloys thereof were grown by electron-beam zone melting and tested in tension between 77° and 373°K. The ductile-to-brittle transition temperature increased sharply with solute concentration, for both tungsten-rich and tantalum-rich alloys; apparently, the maximum transition temperature exists near the 50 pet concentration. Twinning was observed to be a consequence of cleavage-crack propagation. Cleavage occurred on(100)planes, and extensive tearing and "river markings" were present. The onset of brittleness could not be associated with any change in deformation mode, the yield point phenomenon, or the large rise in yield stress with decreasing temperature. Cleavage was observed to initiate at either the specimen surface, or subgrain boundaries. The observation was made that the grain boundaries of Polycrystalline materials are probably even better as nucleation sites for fracture, and are responsible for brittleness at high temperatures and lower solute concentrations than those of the corresponding single crystals. TUNGSTEN and tantalum, the two high-melting neighbors in the third transition period of the periodic table, present striking contrasts. Although both are bee, tungsten has far higher elastic moduli, and the highest ductile-to-brittle transition (DBT) of all the pure metals.' Tantalum, however, is ductile at liquid helium temperatures. Large strain aging and yield point phenomena are observed in tantalum,2,3 but only to a lesser extent in tungsten.4 Tungsten work-hardens at a high rate,5 whereas this effect is negligible in tantalum.' Since the mutual solid solubility of these two metals is complete,7 and no ordering has yet been reported in the binary system, the possibility of depressing tungsten's DBT by tantalum additions was considered. Also, tungsten additions to tantalum could produce hard, high-melting alloys which might be ductile at room temperature. Such alloys offered excellent bases for complex alloy development, particularly with regard to the effect of rhenium on Group VI metals.8"10 In addition, there was the opportunity to examine flow and fracture modes in the vicinity of the DBT, with particular emphasis on the correlation between brittleness and fundamental deformation mechanisms. Myers11 has reported that recrystallized alloys with up to 10 pet W in tantalum are ductile at room temperature, but alloys with 20 pct W could not be swaged at temperatures as high as 500°C. The whole spectrum of Ta-W alloys has been surveyed by Braun, Sedlatschek, and Kiefferl2 using sintered powder compacts. In addition to some physical properties they reported a maximum hardness at about 50 at. pet W, dropping to much lower hardness levels for the pure components. They were able to cold work tantalum-base alloys with as much as 30 pet W and to warm work tungsten-base alloys with up to 20 pet Ta by procedures similar to those used for pure tungsten. EXPERIMENTAL In order to study deformation modes and to keep the impurity concentrations at a minimum, electron-beam zone melting was used to prepare single crystals of high purity. The electron-beam zone melting apparatus is similar to that described by Calverley, Davis, and ever" and incorporates a grid control rectifier to maintain control of emission current. Pure metals were refined by making three zone passes at 4 mm per min up the rod. Alloys were prepared by melting together wire of one constituent on a previously melted rod of the major constituent. Subsequently, two zone passes were made in opposite directions to level the composition after the manner suggested by pfann.14 Purification of the starting materials was accomplished by evaporation of the several impurities, and the degree to which this was accomplished is indicated in the chemical analyses of Table I. The uniformity of composition along a zone levelled rod was within the i 1 pet accuracy of the fluorescent X-ray technique used to determine composition. Crystallographic orientation of the

Jan 1, 1962

By Carl G. Hogberg

During recent months, the acute shortage of steel scrap has necessitated the use of higher percentages of hot metal in the open-hearth charge. With these higher percentages, the sulphur content of hot metal has become an increasingly important factor in the control of the quality of steel. Thus, the blast-furnace operator is faced with a demand not only for more output but for a higher quality of product. More than go per cent of the sulphur charged into the blast furnace is contained in the coke. With the tremendously increased demand, the trend of coke quality has been toward higher sulphur, higher and more variable ash, and poorer physical characteristics. This has been brought about by less selective coal mining, increased production rates in coke plants and resumption of operations of many beehive ovens. In a single month last year, one blast-furnace plant in the Pittsburgh district operated with coke obtained from 52 sources. The effect of variability and quantity of coke ash on blast-furnace operation is well known. The improved results obtained with furnaces operating on coke made from washed coals compared with results on coke made from raw coals is ample proof of the effectiveness of low and uniform ash. Coal-washing plants, however, require a large capital expenditure, and are impractical for most of the large number of small producers, whose operations are confined chiefly to periods of abnormally high demand. Furthermore, not all coals are physically adaptable to washing. Principles 01 Iron Desulphurization in Furnace Although investigations of the blastfurnace process have not clearly revealed the detailed mechanism of iron desulphuri-zation within the furnace, they have been sufficiently extensive to permit a postula tion of the following general principles: 1. Iron, in its travel from furnace top to hearth, continues to pick up sulphur until it has reached tuyere level. The zone of iron desulphurizatioil is relatively narrow, being confined to a vertical distance extending zapproximately from tuyere level to the iron-slag interface in the hearth.' 2. Combustion of coke is confined to spherical zones extending approximately 40 in. from the nose of each tuyere.= Coke ash is released as the coke bums in these combustion areas. 3. With a constant amount of sulphur in the charge, the sulphur content of the metal product is a function of hearth temperature, final slag analysis, slag viscosity, and slag volume. Both hearth temperature and slag analysis affect slag viscosity. For a slag of constant analysis, viscosity always decreases with an increase in temperature;

Jan 1, 1943

By Carl G. Hogberg

During recent months, the acute shortage of steel scrap has necessitated the use of higher percentages of hot metal in the open-hearth charge. With these higher percentages, the sulphur content of hot metal has become an increasingly important factor in the control of the quality of steel. Thus, the blast-furnace operator is faced with a demand not only for more output but for a higher quality of product. More than go per cent of the sulphur charged into the blast furnace is contained in the coke. With the tremendously increased demand, the trend of coke quality has been toward higher sulphur, higher and more variable ash, and poorer physical characteristics. This has been brought about by less selective coal mining, increased production rates in coke plants and resumption of operations of many beehive ovens. In a single month last year, one blast-furnace plant in the Pittsburgh district operated with coke obtained from 52 sources. The effect of variability and quantity of coke ash on blast-furnace operation is well known. The improved results obtained with furnaces operating on coke made from washed coals compared with results on coke made from raw coals is ample proof of the effectiveness of low and uniform ash. Coal-washing plants, however, require a large capital expenditure, and are impractical for most of the large number of small producers, whose operations are confined chiefly to periods of abnormally high demand. Furthermore, not all coals are physically adaptable to washing. Principles 01 Iron Desulphurization in Furnace Although investigations of the blastfurnace process have not clearly revealed the detailed mechanism of iron desulphuri-zation within the furnace, they have been sufficiently extensive to permit a postula tion of the following general principles: 1. Iron, in its travel from furnace top to hearth, continues to pick up sulphur until it has reached tuyere level. The zone of iron desulphurizatioil is relatively narrow, being confined to a vertical distance extending zapproximately from tuyere level to the iron-slag interface in the hearth.' 2. Combustion of coke is confined to spherical zones extending approximately 40 in. from the nose of each tuyere.= Coke ash is released as the coke bums in these combustion areas. 3. With a constant amount of sulphur in the charge, the sulphur content of the metal product is a function of hearth temperature, final slag analysis, slag viscosity, and slag volume. Both hearth temperature and slag analysis affect slag viscosity. For a slag of constant analysis, viscosity always decreases with an increase in temperature;

Jan 1, 1943

By D. H. Davis, I. Fatt

Oil bearing rocks, usually found at depths of 2,000 to 10,000 it, are elastically deformed by overburden pressure. Although the change in porosity with pressure in a number of example rock.: has been shown to be small, it was thought that overburden pressure might have a significant effect on permeability. This note presents results of an investigation to determine the magnitude of the change in permeabilty with pressure. In routine core analysis permeabilities are measured on rock samples which are not under overburden pressure. If permeablity measured in this way differs from permeabilities measured under overburden pressure, a systematic error is introduced into well productivity calculations. The experiments described in this report were made to determine the magnitude of the change and thus to give an estimate of the error introduced into the calculations. The error introduced by the neglect of the change in permeability when overburden pressure is removed may account for part of the difference between well productivity calculated from core analysis and the actual well productivity. The results obtained in this investigation have only quali-tative significance because of the difficulty in reproducing in the laboratory the stress conditions on the rock buried in the earth. The assumption which is usually made is that the rocks in the earth are under a uniform pressure equal to the weight per unit area of the vertical overburden column from the rock in question to the surface of the earth less the pressure of the liquid in the pores of the rock. For an overburden consisting of sandstones and shales (of assumed average specific gravity of 2.3) and for a liquid pressure equal to the pressure in a salt water column (of specific gravity 1.0) reaching from the rock to the surface, the resulting net pressure on the rock is approximately 0.56 psi per ft of depth. EXPERIMENTAL METHOD Clean, dry sandstone core plugs one in. in diameter and about three in. long were mounted in a copper foil jacket as shown in Fig. 3 or molded in a Lucite jacket as shown in Fig. 4. All cores except those labeled "2" in Fig. 1 and "8" in Fig. 2 were measured in the copper foil jacket. Cores "2" and "8" were measured in the Lucite jacket. The jacketed core was placed in a high pressure hydraulic bomb in which the liquid pressure outside the jacket could be raised to 15,000 psi. Flow lines from the core were brought out of the bomb through special fittings in the bomh head and connected to a laboratory type gas permeameter. Measurements were made with nitrogen gas; the maximum mean gas pressure in the core was 16.1 psia. RESULTS The specific permeability of sandstone decreases with in. crease in overburden pressure. Most of the decrease takes place over the range of zero to 3,000 psi overburden pressure. If the net pressure on the rock is assumed to be 0.56 psi per ft of depth as discussed above, 3,000 psi of overburden pressure is equivalent to about 5,000 ft of overburden. At 3,000 psi overburden pressure, the permeability of the eight sandstone core samples tested ranged from 59 to 89 per cent of the permeability without overburden pressure. Figs. 1 and 2 show the permeability reduction as a function of overburden pressure. The permeability of the eight cores without overburden pressure ranged from 4.35 md to 632 md; these permeabilities are listed in Figs. 1 and 2. REFERENCES 1. Carpenter and Spencer: "Measurements of Compressibility of Consolidated Oil Bearing Sands," U. S. Bureau of Mines, R.I. 3450, (1940). * * *

Jan 1, 1952

By C. Chamberlain

The Telfer Project, Australia's newest, largest, and most remote gold mine treats 480 kt of ore grading 9.33 g/t derived from open pit mining operations. Coarse gold is recovered by gravity concentration with jigs and further upgraded wing a continuous strake launder table, and by amalgamation. Remaining gold is recovered in a cyanide circuit and incorporates flat bottom air agitators, counter current decantation (CCD) and stellar filters for clarification and precipitate removal. Overall recovery into a bullion averages 98%. The mill incorporates a number of design features that allow for maximum efficiency and security wing a minimum number of operation personnel.

Jan 1, 1983

By J. D. Forrester

Many have been prone to credit the decline of professional interest in some branches of mineral industry education to the industrialists and other agencies who use our graduates. We hear the cry that industrial salaries are too low, opportunities for advancement do not exist, and the mineral industry specifically and generally is not interested in the engineer's efforts. Perhaps the time now has come when we should "dress-ranks," examine our practices, and publicize and encourage advanced technical training instead of laying all our troubles elsewhere. There can be no doubt but that industry is interested and stands ready and willing to co-operate. This is demonstrated by the numerous grants-in-aid and co-operative industrial projects which have been made available to those relatively few schools which have been encouraging graduate study and research. There is no dearth of research problems in any of the mineral industry fields and the sooner we realize the great opportunities for constructive, technical research in all areas of our profession the sooner we will reap the benefits of our engineering enterprises by closer liaison and broader understanding with industry. An analysis is offered here of the status of graduate work and research in various phases of mineral industry education in the United States. It is

Jan 1, 1949

By M. King Hubbert

In 1856 Henry Darcy described in an appendix to his book, Les Fontaines Publiques de la Ville de Dijon, a series of experiments on the downward flow of water through filter sands, whereby it was established that the rate of flow is given by the equation: q= - K(h2- h2)/I1 in which q is the volume of water crossing unit area in unit time, I is the thickness of the sand, h1 and h2 the heights above a reference level of the water in manometers terminated above and below the sand, respectively, and K a factor of proportionality. This relationship, appropriately, soon became known as Darcy's law. Subsequently many separate attempts have been made to give Darcy's empirical expression a more general physical fornzulation, with the result that .so many mutually inconsistent expressions of what is purported to he Darcy's law have appeared in published literature that sight has often been lost of Darcy's own work and of its significance. In the present paper, therefore, it shall be our purpose to reinform ourselves upon what Darcy himself did, and then to determine the meaning of his results when expressed explicitly in terms of the pertinent physical variables involved. This will be done first by the empirical method used by Darcy himself, and then by direct derivation from the Navier-Stokes equation of motion of viscous fluids. We find in this manner that: q = (N4(p/p)[g - (l/p) gradPI = WE, is a physical expression for Darcy's law, which is valid for liquids generally, and for gases at pressures higher than about 20 atmospheres. Here N is a shape factor and d a characteristic length of the pore structure of the solid, p and IL are the density and viscosity of the fluid, a = (Nd2)(pip) is the volume conductivity of the system, and E = [g - (l/p) grad p] is the impelling force per unit mass acting upon the fluid. It is found also that Darcy's law is valid only for flow velocities such that the inertial forces are negligible as compared with those arising from viscosity. In general, three-dimensional space there exist two superposed physical fields: a field of force of charucteristic vector E, and a field of flow of vector q. The force field is more general than the flow field since it has values in all space capable of being occupied by the fluid. So long as the fluid density is constant or is a function of the pressure only, curl E = 0, E = - grad F where F = gz + dp/p The field of flow, independently of the force field, must satisfy the conservation of mom, leading to the equation of continuity div pq = — f ap/at , where f is the porosity, und t is the time. For steady rnotion ap/at = 0. and div pq = 0 .

Jan 1, 1957

By Ta M. Li

Recent economic and environmental setbacks have not slowed Occidental Oil Shale, Inc.'s program aimed at the commercialization of oil shale. In fact, the firm expects to have a 795 MI (500C) bbl) per day production unit working by the end of 1976. The key to Occidental's ambitious program is an in situ method that extracts the valuable oil by retorting the shale in place. The process will require practically no water and will leave the spent shale in place underground. Additionally, all plant operations are to be located within the mine. These factors thus serve to make the operation attractive from an environmental viewpoint, in contrast to proposed conventional schemes which call for extensive underground mining, crushing and grinding at the surface, and construction of a massive surface retorting facility.

Jan 12, 1976